Tender For Special Repair To Certain Open Shelters, Store Shelters And Living Shelters At New Mal Area Under Ge Sevoke Road
Tender Value
48.30 Lakhs
Estimated cost
Bid Submission
27 Jul 2026
20 days left
EMD
96600
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kalimpong → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Certain Open Shelters, Store Shelters And Living Shelters At New Mal Area Under Ge Sevoke Road
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling plain or corrugated steel sheeting any thickness, complete all as specified and directed. |
| 2 | Dismantling floor hearth or wall tiling and stone slabs including cement mortar bedding ( but not backing ) removing serviceable tiles to store and rubbish off the premises etc complete all as specified and directed |
| 3 | Demolition of cement concrete (un reinforced) in ground floors and paving n. exc. 15 cm thickness (below or above ground level) removing rubbish off the premises etc complete all as specified and directed |
| 4 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 5 | Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs of any thickness including cover fillets complete all as specified and directed. |
| 6 | Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and as directed. |
| 7 | Excavating in trenches not exc 1.5m wide and n.exc 1.5 m in depth, for foundations, etc, or for shafts, wells, cesspits, manholes, pier holes, etc and not exceeding 10 square meter on plan for manholes etc and not exceeding 1.5m in depth and getting out in soft/loose soil complete all as specified and directed. |
| 8 | Returning filling in with approved excavated soil including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed. |
| 9 | Removing excavated soils to a distance not exceeding 50 metres and depositing where directed at a level nexc. 1.5 metre above the starting point complete all as specified and directed. |
| 10 | Materials and Labour for broken stone or boulder hardcore of gauge n exe 63mm deposited, spread and levelled in layers n exe 15cm thick, watered and rammed to a true surface. |
| 11 | Materials and Labour for Sand filling under floors or in foundation including watering and consolidation complete all as specified and as directed. |
| 12 | Materials and Labour for plain cement concrete (1:4:8) type D-2, using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed. |
| 13 | Materials and Labour for formwork to soffits of suspended slabs such as roof slab, floor slabs, landings and similer works, for rough finished flat surfaces of concrete, thickness of slab not exc 200 mm, complete all as specified and directed |
| 14 | Materials and Labour for reinforced cement concrete (1:1.5:3) type A1 (nominal mix) using 20 mm graded stone aggregate as in slabs and shelves supported on walls, beams and columns in floors, roofs and landings etc, any thickness complete all as specified and directed. (Note: Steel reinforcement shall be measured & paid separately) |
| 15 | Materials and Labour for reinforced cement concrete (1:1.5:3) type A1 (nominal mix) using 20 mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels complete all as specified and directed including necessary formwork. (Note: Steel reinforcement shall be measured & paid separately) |
| 16 | Materials and Labour for TMT bars 6 to 8 mm dia , as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed. |
| 17 | Materials and Labour for TMT bars 10 mm dia and over, as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed. |
| 18 | Materials and Labour for rolled mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.conforming to Fe 410-W (Gde-E- 250) quality-A/Fe.290.Gde-E-165 including painted one shop coat of zinc chromate primer paint (including preparation of surface) at workshop before fabrication complete all as specified and as directed. |
| 19 | Supply & fixing Mild steel screw bolt (Machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends each screwed end to be filled with washers and one hexagonal or square nut 5 to 10mm dia shank and exc 5cm but n exc 10cm long complete all as specified and as directed. |
| 20 | Supply & fixing Mild steel screw bolt (Machine made) diameter of neck 16 to 20 mm, with hexagonal or square heads at one end and screwed the other, or screwed both ends each screwed end to be filled with washers and one hexagonal or square nut, exc 5cm but n exc 10cm long complete all as specified and as directed. |
| 21 | Supply & fixing rolled mild steel Flats , channel, angle or tee sections as in wind ties for roof including securing bolts, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed. |
| 22 | Supply & fixing rolled mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment (Fe 290 Gde-E 165) complete all as specified and as directed. |
| 23 | Supply & fixing Mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to steel trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165. |
| 24 | Supply and fixing Pre-painted galvalume aluminum zinc coating (AZ-150) GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed. |
| 25 | Supply and fixing Pre-painted galvalume aluminum zinc coating (AZ-150) GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws , complete all as specified and directed. |
| 26 | Supply and fixing 2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc complete all as specified and directed. |
| 27 | Materials and labour for preparing of new steel surfaces of any description , over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed. |
| 28 | Materials and labour for preparing of new steel surfaces of any description , below 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed. |
| 29 | Materials and labour for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 15 mm thick screed bed or bedding layer of cement mortar (1:4) for laying of floor finishes complete all as specified and directed. |
| 30 | Materials and labour for coloured 350x250x7-8 mm /300x450x7-8 mm thick glazed ceramic tiles on vertical surfaces such as skirting,dado and risers to steps etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 10mm thick backing coat in cement mortar (1:4) , complete all as specified and directed. |
| 31 | Materials and labour for Vitrified Ceramic tiles of light shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & incl 15 mm th screed bed in CM 1:6 complete all as specified and as directed. |
| 32 | Materials and labour for Vitrified Ceramic tiles of light shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in vertical serfaces etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & incl 10mm thick backing coat in cement mortar (1:4) , complete all as specified and directed. |
| 33 | Materials and labour for Kota stone slab 20-25mm thick in riser of steps,skirting,dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including 10mm thick backing coat in cement mortar (1:4) including rubbing and polishing complete. |
| 34 | Materials and labour for Kota stone slab 20-25mm thick in floor laid over and including 20mm thick screed bed or bedding layer of cement mortar (1:6)and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. |
| 35 | Materials and labour for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand Complete all as specified and as directed |
| 36 | Materials and labour for 75 mm thick plain cement concrete (1:3:6) type C2 using 40 mm graded stone aggregate as in floors, plinth protection, path etc. finished the surface of concrete even and smooth without using extra cement, complete all as specified and directed. |
| 37 | Materials and labour for 25 mm thick PCC (1:2:4) type B0 using 12.5 mm graded stone aggt as in sub bases of floor finished even and rough, complete all as specified and directed. |
| 38 | Materials and labour for 40mm thick PCC (1:2:4) type B0 using 12.5 mm graded stone aggt as in DPC, WPC shall be mixed with concrete as directed, complete all as specified and directed. (Note: WPC shall be measured and paid separately as supply only). |
| 39 | Materials and labour for brick work with fly ash bricks modular size, straight or curved on plan exc. 6mtr mean radius, built in cement mortar 1:6, complete all as specified and directed. |
| 40 | Materials and labour for brick work with sub class 'B' burnt clay bricks straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed. |
| 41 | Supply and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators and partitions with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed. Please Enable Macros to View BoQ information |
| 42 | Supply and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators and partitions with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 04, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 27, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 20 daysJul 29, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 22 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender