Tender For Special Repair To Building No. Ch-10 (Officers Mess) At Command Hospital (Wc) Chandimandir Under Ge (U) Chandimandir.
Tender Value
1.22 Crore
Estimated cost
Bid Submission
31 Jul 2026
26 days left
EMD
1.97 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Panchkula → Haryana
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Building No. Ch-10 (Officers Mess) At Command Hospital (Wc) Chandimandir Under Ge (U) Chandimandir.
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (reinforced) in of any description and in any position (reinforcement cut as required to facilitate demolition) not otherwise specifically provided for cand removal of debris not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above starting point complete all as specified and as directed by Engineer-in-charge. |
| 2 | M&L for Reinforced Cement concrete (Design Mix), M-25 (using 20 mm graded stone aggregates) as in slabs supported on walls complete all as specified and as directed by Engineer-in-Charge. |
| 3 | M&L for Reinforced Cement concrete (Design Mix), M-25 (using 20 mm graded stone aggregates) as in fins, fascias, louvres, parapets, and railings exceeding 60 cm in height, newels, balustrade, and the like complete all as specified and as directed by Engineer-in-Charge. |
| 4 | M&L for use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar works not exceeding 200 mm thick horizontal or slopping in rough finished flat surface of concrete complete all as specified and as directed by Engineer-in-Charge. |
| 5 | M&L for use and waste of formwork to faces of walls, abutment, parapets and similar works including attached pillars, butteresses etc vertical arch to batter for rough finished flat surfaces of concrete complete all as specified |
| 6 | M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed by Engineer-in-Charge. |
| 7 | M&L for installing rebars of dia 10mm and above in the bldg components i.e., beam, column, parapet wall, roof drop or fascia and slab with chemical anchoring compound by drilling holes of dia and depth as per manufacturers instructions complete all as specificed and as directed by Engineer-in-Charge. |
| 8 | Demolition of brickwork or stone boulder masonary, built in cement mortar including all quions, arches pillars etc., but excluding ashlar facings including removing debris from the site complete all as specified and as directed by Engineer-in-Charge. |
| 9 | M&L for Brick work using sub class 'B' bricks (old size bricks), straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6, complete all as specified and as directed by Engineer-in-Charge. |
| 10 | Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15 cm thick above or below ground level complete all as specified and as directed by Engineer-in-Charge. |
| 11 | M&L for plain cement concrete, 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed by Engineer-in-Charge. |
| 12 | M&L for 75 mm thick cement concrete 1:3:6, type C-2 (using 40 mm graded stone aggregate) as in floors, plinth protection (finished even and fair) laid in panels including joints filled with sealing compound grade 'A' complete all as specified and as directed by Engineer-in-Charge. |
| 13 | M&L for Providing and laying 60 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50 mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paverblocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed by Engineer-in-Charge. |
| 14 | M&L for plain cement concrete type 1:2:4, type B-1 (using 20 mm graded stone aggregate), as in copings and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and as directed by Engineer-in-Charge. |
| 15 | Demolition of stone slabs and tiles of any description or thickness in floors, aprons Laid, bedded and pointed in any mortar etc., complete all as specified and as directed by Engineer-in-Charge. |
| 16 | M&L for 18-20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15 mm thick screed bed or bedding layer in cement mortar 1:4 all as specified and as directed by Engineer-in-Charge. |
| 17 | Extra over Granite or marble slabs as in rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations etc., complete all as specified and as directed by Engineer-in-Charge. |
| 18 | M&L for Makrana White Marble work, 18 to 20 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge. |
| 19 | M&L for Machine cut kota stone slab flooring 18-20 mm thick, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, over and including 20 mm thick bedding in cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge. |
| 20 | M&L for Machine cut kota stone slab as in skirting 18-20mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete and including 10mm thick back coat in cement mortar 1:3 complete all as specified and as directed by Engineer-in-Charge. |
| 21 | S&F PVC wall panelling, hollow cored, 5 mm thick, decorative designs with smooths surfaces, fire resistant, water and heat proof, tongue and groove edge for easy assembly with all accessories such as U cap, end cap, tee, plugs, fillets and screws etc as per manufactures instructions and fixing complete all as specified and as directed by Engineer-in-Charge. |
| 22 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed by Engineer-in-Charge. |
| 23 | M&L for excavating in post holes (or similar holes) each not exceeding 0.5 cum, in soft/ loose soil, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm and removing surplus soil to a distance not exceeding 50 metre complete all as specified and as directed by Engineer-in-Charge. |
| 24 | S&F MS steel work in tubular trusses, posts and purlin including special shaped washers etc., complete using butt welded tubes confirming to IS 1161- 1979 graded St 240 with one shop coat of zinc chromate primer paint complete all as specified and as directed by Engineer-in-Charge. |
| 25 | S&F Mild steel works as in Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-410-W (Gde-E-250) quality B complete all as specified and as directed by Engineer-in-Charge. |
| 26 | M&L for preperation of new steel surfaces of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engineer-in-Charge. |
| 27 | Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering including stacking properly complete all as specified and as directed by Engineer-in-Charge. |
| 28 | S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of mangalore pattern of any colour having tensile strength of 550Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and as directed by Engineer-in-Charge. |
| 29 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet, 0.50 mm thick of any colour having tensile strength of 550 Mpa as in valley/ gutter/ eve board fixed with self tapping screws etc., complete all as specified and as directed by Engineer-in-Charge. |
| 30 | Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets complete all as specified and as directed by Engineer-in-Charge. |
| 31 | Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of semi perforated perforated 12mm thick micro tegular edged GRG false ceiling tiles of size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 4 76 (part 4 )-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of mainT runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of s1ze 600x 600mm , suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50 mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000 mm length and L shape level adjuster of size 85 x 25 x 2mm. Galvanised iron perimeter wall angle of size 24 x 24 x 0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge. |
| 32 | Material and labour for GI Frame work for seamless ceiling comprising of GI perimeter channel 0.55mmm thick with two unequal flanges of 20 and 30 mm and web of 7 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15mm each and web of 45mm suspended form soffit at approx 900 mm centre to entre with GI cleat and steel expansion fasteners with and including ceiling section (not excwwding 1.2 m length) of 0.55 mm thickness having kurled web of 50mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre complete all as specified and as directed by Engineer-in-Charge. |
| 33 | Material and labour for Providing and fixing 10 mm thick plaster of Paris ceiling (Gypsum anhydrous) to curved surface over 2nd class soft wood fillets or metal frame work and reinforced with G.I. wire mesh complete all as specified and as directed by Engineer-in-Charge.(Note: Fillets, metal frame work and G.I. wire mesh paid separately) |
| 34 | Taking down cement plaster of any description on brick or stone walls/ chipping off cement concrete in any situation, etc. including raking out joints, hacking for key, scrubbing down with water complete all as specified and as directed by Engineer-in-Charge. |
| 35 | M&L for rendering 15 mm thick in Cement Mortar 1:4 mixed with water proofing compound as per manufacturer's instructions on fair faces of concrete/ brick surfaces, finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.Note: WPC shall be measured and paid separately. |
| 36 | M&L for rendering 5 mm thick on ceiling surfaces in cement mortar 1:3 on fair faces of brick work or concrete surfaces and finishing the surface even and smooth complete all as specified and as directed by Engineer-in-Charge. |
| 37 | M&L for Rendering 10 mm thick on fair faces of brick work or concrete surfaces in CM 1:6, finished even and smooth without using extra cement (Internal surfaces), complete all as specified and as directed by Engineer-in-charge. |
| 38 | Supply only liquid integral water proofing compound, ISI Marked, complete all as specified. |
| 39 | M&L for preparation of newly plastered surfaces of walls and applying two coats of plastic emulsion paint using mechanical means/ hand roller over a coat of priming paint including 1 mm thick cement based wall care putty complete all as specified and as directed by Engineer-in-Charge. |
| 40 | M&L for preparation of newly plastered ceiling surfaces and applying two coats of plastic emulsion paint using mechanical means/ hand roller over a coat of priming paint including 1 mm thick cement based wall care putty complete all as specified and as directed by Engineer-in-Charge. |
| 41 | M&L for preparation of newly plastered surfaces of walls and Finishing with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and as directed by Engineer-in-Charge. |
| 42 | M&L for preparation of old plastered wall surfaces and applying one coat of plastic emulsion paint complete all as specified |
| 43 | M&L for preparation of old plastered ceiling surfaces and applying one coat of plastic emulsion paint complete all as specified |
| 44 | M&L for Complete removal of existing treatment from wall surfaces and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over 01 mm thick water proof wall putty complete all as specified and as directed by Engineer-in-Charge. |
| 45 | M&L for Complete removal of existing treatment from wall surfaces and finishing with textured exterior paint of required shade : Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm over 1 mm thick wall care putty complete all as specified and as directed by Engineer-in-Charge. |
| 46 | M&L for Preparation of old treated wood & wood based surfaces of any description, not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-charge. |
| 47 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by Engineer-in-Charge. |
| 48 | Material and labour for 25 mm thick plain cement concrete 1:2:4, type B-0 (using 12.50 mm graded stone aggregate) as in levelling courses, finished even & rough to receive topping layer complete all as specified and as directed by Engineer-in-Charge. |
| 49 | M&L for Non-skid Ceramic coloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and as directed by Engineer-in-Charge. |
| 50 | M&L for Glazed ceramic coloured tiles in vertical surface 350 mm x 250 mm x 7 mm/ 450 mm x 300 mm x 7 mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tile over and including 10 mm thick rendering in cement mortar 1:4 complete all specified and as directed by Engineer-in-Charge. |
| 51 | M&L for double charged vitrified ceramic coloured, 8-9 mm thick (square/ rectangular) polished, area of each tile exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc., set and jointed in neat cement slurry and pointed in white cement paste pigmented to tile shade over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and as directed by Engineer-in-Charge. |
| 52 | All as per serial item No. 51.00 here-in-before but on vertical surface such as skirting, dado over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge. |
| 53 | Providing and fixing of aluminium composite panels in cladding of approved make having total thickness of 4 mm (Top coil 0.50 mm, non toxic PE core 3 mm and back coil - 0.50mm) with 25 micron PVdF coating on top coil and polyster/ epoxy coating on back coil (4 to 7 micron) on aluminium sub structure fixed with 19mm x 12mm x 1.6mm aluminum cleat & 10 x 100 mm SS wooden screws with PVC plug on faced horizontal/ vertical surfaces of rectanguler/ circuler columns, suspended ceiling cills, jambs, canopy with and including necessary aluminium frame, scaffolding etc., and making 12 mm to 20 mm wide grooves and applying non staining and non streaking sealants of dow corning (789 or 991HP) and backing rods complete as specified. Note : (i) Only exposed surface shall be measured and paid for.(ii) ACP material shall be for exterior application & of shade as approved by GE. |
| 54 | Dismantling of cast iron drain pipes, 100 mm bore, with fittings, jointed in cement mortar and taking out of trenches complete all as specified and as directed by Engineer-in-Charge. |
| 55 | Dismantling of cast iron drain pipes 75mm bore, with fittings, jointed in cement mortar and taking out of trenches complete all as specified and as directed by Engineer-in-Charge. |
| 56 | S&F PVC(SWR) soil or waste pipe, 110 mm bore, single socketed in any length type 'B' with rubber ring joints fixed to wall complete all as specified and as directed by Engineer-in-Charge. |
| 57 | All as per srl item No. 56.00 here-in-before but 75 mm bore |
| 58 | S&F PVC (SWR) bend in any radius 110 mm dia. complete all as specified and as directed by Engineer-in-Charge. |
| 59 | S&F PVC (SWR) bend in any radius 75 mm dia. complete all as specified and as directed by Engineer-in-Charge. |
| 60 | Taking down chowkhats or frames of area not exceeding 1.5 Sqm each (without taking off shutters from the frame) complete all as specified and as directed by Engineer-in-Charge. |
| 61 | Taking down chowkhats or frames of area exceeding 1.5 Sqm but not exceeding 4.00 sqm each (without taking off shutters from the frame) complete all as specified and as directed by Engineer-in-Charge. |
| 62 | S&F Pressed steel frames for doors (size of frame 105 x 60 mm) with one or more rebates including necessary fixing hinges, lugs, lock, strike plate, hold fasts, peg etc including PCC 1:3:6 type C-0 (using 12.50 mm graded stone aggregates) for back filling of chowkat complete all as specified and directed by Engineer-in-charge. |
| 63 | S&F flush shutters, 35 mm thick, solid core construction with particle board core and plywood face panels commercial type on both sides with lipping/ frame to match complete all as specified and as directed by Engineer-in-Charge. |
| 64 | S&F solid PVC door frame of size 50 x 47 mm, made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed by Engineer-in-Charge. |
| 65 | S&F Factory made particle board core solid PVC moulded door shutter, 28 to 30 mm thick (stiles), with 2, 4 or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2 mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and as directed by Engineer-in-Charge. |
| 66 | M&L for preparation of new wooden surfaces of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-charge. |
| 67 | S&F 100 mm size butt hinges, medium weight, stainless steel complete all as specified and as directed by Engineer-in-Charge. |
| 68 | S&F 100 mm long stainless steel barrel tower bolts, complete all as specified and as directed by Engineer-in-Charge. |
| 69 | S&F 150 mm size stainless steel handles, complete all as specified and as directed by Engineer-in-Charge. |
| 70 | S&F 250 mm long stainless steel sliding door bolts with hasp and staple (bolt type) and fixing clips complete all as specified and as directed by Engineer-in-Charge. |
| 71 | S&F HDHMR prelaminated (one side laminated and inner side balancing white) board of 18-20 mm thick having minimum density of 32kg/cum as in kitchen cabinet work, Side hug/ top hung shutter including fixing of all necessary hardwares (which includes Moduler handles, SS hinges, Magnetic lock, hydraulic closer for top hung shutter cabinets) tapping on edges, fixing screws duly dipped in adralite solution etc complete all as specified and as directed by Engineer-in-Charge. |
| 72 | S&F Solid PVC Wall Lining, consisting of 5 mm thick coloured PVC sheet inclusive of solvent cement and preparing existing surface and fixing at site as on cupboard etc., complete all as specified and as directed by Engineer-in-charge. |
| 73 | S&F 18 mm thick coloured, solid PVC sheet suitably fixed as in shelving of cupboard etc., as per direction and specifications complete all as specified and as directed by Engineer-in-charge. |
| 74 | S&F door closer, hydraulically regulated, aluminium (extruded section) body, designation No. 3, universal type, suitable for top hung cabinet shutter upto 700 mm in width and of weight not more than 35 Kg complete all as specified and as directed by Engineer-in-Charge. |
| 75 | S&F stainless steel magnetic hinges, 70-80 mm long, L type suitable for modular kitchen cabinet shutters complete all as specified and as directed by Engineer-in-Charge. |
| 76 | S&F stainless steel soft auto closing 45 mm wide Ball bearing runners with telescopic Channel, suitable for modular kitchen cabinet drawers/ racks upto 800 mm long complete all as specified and as directed by Engineer-in-Charge. |
| 77 | S&F brass cupboard knobs, 35-40 mm dia fixed with SS screws complete all as specified and as directed by Engineer-in-Charge. |
| 78 | S&F SS handles, fancy type, 75 mm size complete all as specified and as directed by Engineer-in-Charge. |
| 79 | S&F brass mortice lock, 75 mm size with 2 levers, vertical type with necessary screws etc., complete all as specified and as directed by Engineer-in-Charge. |
| 80 | S&F framed work such as grills, grating, etc., with ends of bars shouldered and/ or rivetted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work for water tanks and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed by Engineer-in-Charge. |
| 81 | Supplying and fixing in repair toughened glass of selected quality, 12 mm thickness in vertical profile as in doors, partitions and similar work including cutting to shape, drilling holes, fixing with mullions, floor spring plates complete all as specified and as directed by Engineer-in-Charge. |
| 82 | M&L for providing and fixing factory made uPVC white colour casement (Openable) doors, made of extruded profile wilh wall thickness of 2.3 mm (+0.2 mm). Window profile with hollow section with multi chamber, frame (60 mm x 58 mm), sash (60 mm x 78 mm). T profile (One vertical length in between two shutters) (60 mm x 74 mm). Glazing bead (35 mm x 20 mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + 0.2 mm thick galvanized steel Frame (28 mm x 21.5 mm), sash (31 mm x 27 mm), T profile (27 mm x 17 mm) to be inserted in required profile, frame will be fixed to the wall wilh 8 mm x 100 mm long fasteners, including hardwares such as casement door handle made of zinc alloyed (white powder coated), corner striker, secondary strikers, cylinder, door transmission gear made of mild sleel with multi point locking system with strikes, 3D Hinges of zinc alloyed (white powder coated) complete all as specified and as directed by Engineer-in-Charge. |
| 83 | Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose. |
| 84 | M&L for providing and fixing factory made uPVC white colour sliding window (Three track), area of each window not exceeding 2.0 Sqm, made of extruded profiles with wall thickness of 2.3 mm (+ 0.2 mm), Window profile with hollow section with multi chamber, Frame (88 mm x 52 mm), sliding sash (42 mm x 67 mm), Sliding mesh Sash (42 mm x 57 mm) Sliding interlock (One vertical length in each shutters) (45.50 mm x 28 mm), Glazing bead (24.50 mm x 16 mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM gasket, 1.2+0.2 mm thick galvanised steel Frame (30 mm x 18 mm) 2 nos, sliding sash (30 mm x 18 mm), sliding mesh sash (26 mm x 10 mm) profile to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100 mm long fasteners, Hardware (Touch Lock of zinc alloyed (white powder coated), steel roller system, Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and required accessories complete all as specified and as directed by Engineer-in-Charge. |
| 85 | Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose. |
| 86 | M&L for Providing and fixing factory made uPVC white colour Sliding window (Three track), area of each window exceeding 2.0 Sqm, made of extruded profiles with wall thickness of 2.3 mm (+ 0.2 mm), Window profile with hollow section with multi chamber, Frame (88 mm x 52 mm), sliding sash (42 mm x 67 mm), Sliding mesh Sash (42 mm x 57 mm) Sliding interlock (One vertical length in each shutters) (45.50 mm x 28 mm), Glazing bead (24.50 mm x 16 mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM gasket, 1.2+0.2 mm thick galvanised steel Frame (30 mm x 18 mm) 2 nos, sliding sash (30 mm x 18 mm), sliding mesh sash (26 mm x 10 mm) profile to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100 mm long fasteners, Hardware (Touch Lock of zinc alloyed (white powder coated), steel roller system, Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and required accessories complete all as specified and as directed by Engineer-in-Charge. |
| 87 | Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose. |
| 88 | S&F 4.8 mm thick, tinted sheet glass, ordinary quality and glazing with silicon sealent, fixed in any frame as in windows/ ventilators, size in squares not exceeding 0.5 Sqm in each pane complete all as specified and as directed by Engineer-in-charge. |
| 89 | M&L for 4 mm thick aluminium composit panel (ACP) of approved color as in doors, windows & partitions fixing with aluminium beading or as per manufacturer's instructions including joint filling and tapping, with necessary arrangement complete all as specified and as directed by Engineer-in-Charge. |
| 90 | S&F in repair aluminum (extruded section body) door closer, hydraulically regulated, designation No. 1 universal type, suitable for door shutters up to 700 mm in width and of weight not more than 35 kg and fixed complete all as specified and as directed by Engineer-in-charge. |
| 91 | S&F floor springs, double action, hydraulically regulated, made up of minimum 1.25 mm thick aluminium alloy sheet foundation box main body with steel cover, govening pivot made of brass, other parts made of MS heavy duty fixed complete all as specified and as directed by Engineer-in-Charge. |
| 92 | S&F in repair Aluminum (extruded section body) door closer, hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg, complete all as specified and as directed by Engineer-in-charge. |
| 93 | Taking up or down 15 mm bore steel tubing with connections or fittings from wall, ceiling, floor etc., including removal from site, complete all as specified and as directed by Engineer-in-Charge. |
| 94 | Taking up or down 20 mm bore steel tubing with connections or fittings from wall, ceiling, floor etc., including removal from site, complete all as specified and as directed by Engineer-in-Charge. |
| 95 | Supplying and fixing 20 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings including cutting, threading and fixing as required on walls/ ceiling or laying in floors complete all as specified and as directed by Engineer-in-Charge. |
| 96 | Supplying and fixing 25 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings including cutting, threading and fixing as required on walls/ ceiling or laying in floors complete all as specified and as directed by Engineer-in-Charge. |
| 97 | S&F brass elbow suitable for 20 mm CPVC Pipe complete all as specified and as directed by Engineer-in-Charge. |
| 98 | S&F brass elbow suitable for 25 mm CPVC Pipe complete all as specified and as directed by Engineer-in-Charge. |
| 99 | S&F brass tee suitable for 20 mm CPVC Pipe complete all as specified and as directed by Engineer-in-Charge. |
| 100 | S&F brass tee suitable for 25 mm CPVC Pipe complete all as specified and as directed by Engineer-in-Charge. |
| 101 | Cutting chases, pinning in, making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintel etc. and cutting chases for concealed water tubing or concealed conduit wiring etc. complete all as specified and as directed by Engineer-in-Charge. |
| 102 | M&L for White Vitreous China Wall-Hung Water closet of Rimless Bowl Design with anti-bacterial glazing uptill trap end and with soft closing seat & cover, complete all as specified and as directed by Engineer-in-Charge. |
| 103 | Supply, fixing and commissioning wall Concealed WC Flushing Cistern with Flushing Actuator Plate in chrome, Per flush water discharge rate 2L-4L complete all as specified and as directed by Engineer-in-Charge. |
| 104 | Supply & fixing Hand Spray/ with lever control (health faucet) with flow Rate of 3.78 LPM at 3 Bar pressure complete all as specified and as directed by Engineer-in-Charge. |
| 105 | Supply and fixing toilet roll holder with flap complete all as specified and as directed by Engineer-in-Charge. |
| 106 | Supply and fixing chrome finish two way bib cock with wall flange flow rate of 6 lpm @ 3bar of pressure, Nickel-10.0 micron Chromium-0.3 micron complete all as specified and as directed by Engineer-in-Charge. |
| 107 | Supply & Fixing of chrome finish brass angle valve, 15 mm bore, having Plating: Nickel-10.0 micron Chromium-0.3 micron complete all as specified and as directed by Engineer-in-Charge. |
| 108 | Supply and fixing white vitreous china urinal without sensor but with fixing accessories set, back inlet, anti germ glaze, concealed inlet & outlet to protect from faulse smell with Overall, Product Size 385 mm x 325 mm x 635 mm of approved make complete all as specified and as directed by Engineer-in-Charge. |
| 109 | Supply and fixing in repair urinal sensor concealed type flush valve for urinal complete set with 4 meter adopter wire installation box & control valve (9V transformer), water supply single line, pipeline Inlet & outlet lines (1/2\\" BSP/15mm), Flow Control with Brass Radiator Valve, Minimum residence time Around 7 Seconds, Flush Time 6 to 8 Seconds, Sensor range about 400mm (Default - High) Range Adjustable - 2 Steps (High & Low) (+/- 20%) High - 400 mm Low - 250 mm, Materails Base - PS Front Plate - SS -304 ,Eye PCB Holder - PC , Fixing Bracket - Nylon, Water Release Unit - Brass, Flow rate for Green fitting: 1 lpm @ 3Bar of water pressure of approved make complete all as specified and as directed by Engineer-in-Charge. |
| 110 | Supply and fixing Chrome finish Curved shaped urinal partition with frosted glass of thickness of 8 mm height 900 mm and width 450 mm complete all as specified and as directed by Engineer-in-Charge. |
| 111 | Supply and fixing in reapir wash basin White glazed vitreous china under counter sunk Oval shaped wash basin of size 560x430x195mm complete all as specified and as directed by Engineer-in-Charge. |
| 112 | Supply and fixing Sensor Faucet for Wash Basin (9V transformer), Water Supply Cold or premix water (1 inlet),Water Temperature Maximum 65 ℃ ,Environment working Temperature 0 to 40℃ ,Self-close Over ride Time 12 sec, IP Rating Protection against intrusion (control box) IP 66 and Protection against Ingress (sensor eye) IP 66, Factory setting Parameters Detection Range : 10 CM - 22CM Valve shut of Time : < 2s Detection Time/ Response Time : Sensor activation time : < 1s, Finish Plating: Nickel-10.0 micron Chromium-0.3 micron Flow rate for Green fitting: 3.8 lpm @ 3Bar of pressue of approved make complete all as specified and as directed by Engineer-in-Charge. |
| 113 | Supply and fixing CP brass Chrome Polished finish Waste coupling 32mm Size Half Thread with 80mm Height complete all as specified and as directed by Engineer-in-Charge. |
| 114 | Supply and fixing Polished Chrome finish Bottle Trap 32mm Size with 300mm & 190mm Long Wall Connection Pipes & Wall Flange complete all as specified and as directed by Engineer-in-Charge. |
| 115 | Supply and fixing in repair CP Brass Towel ring complete all as specified and as directed by Engineer-in-Charge. |
| 116 | Supply and fixing stainless steel AISI 304 grade, touch-free infra-red hand dryer with 1150W rated power & carbon brush motor 1150W with heater on, 500W with heater off, eco-friendly, Built in UV light to kill bacteria in air with Power and working LED indicator and with Air speed 60 m/s and sensing rage 15-20 cm complete all as specified and as directed by Engineer-in-Charge. |
| 117 | Supply and fixing napkin paper dispensor stainless steel AISI 304, satin finish, Fully welded body, 0.8mm thick with blurr-free edges, Seamless one-piece lid, 0.8 mm thick, fixed to the body by means of 2 rivets that allows swinging down of lid for replenishment, Back-plate, 0.8 mm thick, with multiple slots for easy installation, The towel tray opening has bound edges to minimize tearing of paper towels.Slot at the front that indicates the content level. Dimensions 275x330x133 mm and paper capicity Max. 260x100 mm paper towel dispenser of approved make complete all as specified and as directed by Engineer-in-Charge. |
| 118 | Providing and fixing CP Brass Tumbler holder complete all as specified and as directed by Engineer-in-Charge. |
| 119 | Providing and fixing Soap Dispenser with Metallic Bottle complete all as specified and as directed by Engineer-in-Charge. |
| 120 | Providing and fixing CP Brass wall Mounted sink mixer with swinging casted spout complete all as specified and as directed by Engineer-in-Charge. |
| 121 | S&F in repairs sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 510mm x 510mm bowl size 460 mm x 460 mm x 230 mm complete all as specified and as directed by Engineer-in-Charge. |
| 122 | Supply and fixing bevelled edge mirror of selected quality glass of 5.5 mm thick, each providing 04 Nos holes on corner, fixed with 4 Nos of 3 Inch screws and rawl plugs including 4 Nos good quality SS Cap (on screw head) etc, complete all as specified and directed by Engineer-in-Charge. |
| 123 | S&F in repairs vitreous china wash down water closet pan (Pedestal Pattern), white including plastic water closet seat cover, black, closed pattern with flat bottom with mild steel chromium plated or aluminised hinging device and fixing with all joints to WC pan complete all as specified and as directed by Engineer-in-Charge. |
| 124 | S&F in repair PVC 10 litres capacity syphonic action type flushing cistern, low level with inlet, ball valve and float including brackets, flush pipe of PVC 32mm bore and connection to WC pan complete all as specified and as directed by Engineer-in-Charge. |
| 125 | S&F in repair vitreous china wash basin, white, flat back, size 550 x 400 mm including waste fitting brass chromium plated and fixing with new brackets including cutting and pinning in ends of brackets complete complete all as specified and as directed by Engineer-in-Charge. |
| 126 | S&F in repair Pillar taps, 15 mm bore dia, fancy type, cast copper alloy with capstan heads chromium plated screwed down hidh pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge. |
| 127 | M&L PVC (SWR) floor trap, 100 mm dia, plain with grating including jointing to waste pipe fixed in solvent cement complete all as specified and directed by Engineer-in-Charge. |
| 128 | S&F in repair chromium plated towel rail, 600 mm long complete all as specified and as directed by Engineer-in-Charge. |
| 129 | S&F in repair curtain rods 20mm dia of mild steel chromium plated with fixing brackets, stop rollers etc. complete all as specified and as directed by Engineer-in-Charge. |
| 130 | S&F brackets, brass, chromium plated, fancy type for curtain rods complete all as specified and as directed by Engineer-in-Charge. |
| 131 | Cutting into existing manholes for connecting new drains 100mm dia, making good to pipe & rendering, cutting out existing benching for & forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, & reforming benching as required complete all as specified and as directed by Engineer-in-Charge. |
| 132 | S&F as in repairs PVC flexible waste pipe of standard length 25mm dia. with PVC cap suitable for waste coupling 32/ 40mm complete all as specified and as directed by Engineer-in-Charge. |
| 133 | S&F in repairs 1000 litres capacity rotational moulded polye-thylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I with and including 20mm bore dia Ball brass valves, high pressure, with polythene float and flynut complete,screwed for iron pipe or brass ferrule and fixed etc complete all as specified and as directed by Engineer-in-Charge. |
| 134 | M&L for bees-wax polishing on surfaces of any description, width or girth including cleaning and preparing the surface complete all as specified and as directed by Engineer-in-Charge. |
| 135 | Dismantling of Brick tiles or terracing tiles, single layer on roofs and removal of rubbish (except tiles) off the premises to a distance upto 100 metre complete all as specified and as directed by Engineer-in-Charge. |
| 136 | Demolition of Mud in roofs (or complete removal of existing treatment) any thickness, including plastering and leaping (whether full thickness removed or only or part thereof) and removal of rubbish off the premises to a distance upto 100 metre complete all as specified and as directed by Engineer-in-Charge. |
| 137 | M&L for PCC 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges, base of over head tank, roof padding and similar work including all necessary formwork if necessary complete all as specified and as directed by Engineer-in-Charge. |
| 138 | Material and labor for waterproofing treatment to roof complete in the following stages :- (a) SURFACE PREPARATION: Cleaning top surface of roof/ RCC slab using electric wire cup grinder to remove surface imperfections, sharp edges or protrusions at the junctions to achieve a uniform surface profile. Cleaning thoroughly the concrete surface using a high-pressure water jet to eliminate all dirt, dust, oil spillage, laitance, and other contaminants. (b) SURFACE CRACK REPAIR: Cracks on top surface/ RCC slab wider than 1 mm required to be cut and open in V-groove manner (8 mm wide x 6 mm deep) by using mechanical cutter, clean the same and fill with high modulus, moisture curing, silyl modified polymer (hybrid) sealant and allow sealant to air cure for 3 days |
| 139 | (c) ANGLE FILLET TREATMENT: Providing and preparing angle fillet at all vertical up stands and junctions/ corners. Moist the surface with water, apply bond coat prepared by mixing universal repair polymer (URP) and cement in 1:1 ratio by volume and apply using brush, preparing PMM by mixing 1 kg of URP, 5 kg fresh cement and 15 kg graded quartz sand, (i.e. in the ratio of 1:5:15 and preparing angle fillet (gola) of size 50 mm x 50 mm over the wet bond coat and finishing the same followed by moist curing the surface for 48-72 hours complete |
| 140 | (d) RAINWATER OUTLET TREATMENT: Hacking and chipping the surface around the rainwater drain outlet up to 25 mm in depth, applying bond coat of universal repair polymer (URP), in ratio of 1:1 (URP 1 : cement 1) by volume, over the corners and pipe insert outlet gaps, filling the gaps around drain mouth with PMM (Polymer Modified Mortar), mixed with universal repair polymer (URP) 10% by weight of cement, in the ratio 1:3. Providing and fixing 100 mm width, 225 GSM, fiber glass chopped strand mat around the periphery of drain mouth of rainwater outlet, sandwiched with two-component UV resistant hybrid urethane elastomeric waterproof top coat. Applying two thick coats of two-component UV resistant hybrid urethane elastomeric waterproof coating to completely cover the mesh/ fabric and surrounding area. (e) WATERPROOFING APPLICATION: Preparing premix of two-component high-strength hybrid urethane elastomeric waterproofing coating using an electric double paddle mixer at low speed for 2-3 minutes until a uniform blend is achieved without dilution. Applying the waterproofing coating on an SSD (Saturated Surface dry) condition, apply first coat mix at the rate 0.8-0.9 kg/sqm using a lamb's wool roller |
| 141 | Contd.. While the coating is still wet, roll and embed a 225 gm fiberglass chopped strand mat ensuring full bonding without air bubbles or wrinkles and overlap joints by at least 5 cm at end points & allow the first coat to dry for 3-4 hours. Applying the second coat at 90 degrees angle to the first coat at 0.9 kg/sqm once the surface is dry enough to walk on. Additional coats may be applied as required to achieve a forced material consumption to obtain a DFT of 1000 to 1200 microns with minimum material consumption of 1.8 kg/sqm over 2-3 undiluted coats. The coating should terminate below the drip mold on vertical surface. The system complies achieving tensile strength 215 N/mm2 (ASTM D2370 : 2016), Tear strength 2100 N/mm2 (as per ASTM D624), Dynamic crack bridging (EN 13251 : 2016), Shore A hardness: 85, zero water permeability: at 15 bar as per (EN 12390-8: 2019), passes water migration resistance: no leakage, no temperature flexibility: (-) 20 degree Celsius after 1000 hours, UV (ASTM D1970 : 2021), Solar reflectance index : 90 (ASTM E1980 for white), Peel adhesion to concrete (wet condition, 24 hours.), ASTM C794-12, root resistance according to CEN/TS14416-2014 complete all as specified. |
| 142 | Providing and laying non-woven geotextile membrane of minimum 100 GSM, laid loosely over the completed waterproofing membrane including all necessary cutting, alignment, and positioning, with minimum 100 mm overlap at all joints, complete in accordance with the manufacturer's specifications and directions, as approved by the Engineer-in-Charge |
| 143 | Repair of damaged roof screed and formation of slope Removing all loose, damaged, and deteriorated concrete/screed from the roof surface in required pockets using mechanical cutters and suitable tools. Clean the prepared surface thoroughly with high-pressure water jetting to remove dust, dirt, laitance and all loose particles. Applying a bonding coat comprising Universal Repair Polymer (URP) mixed with cement in the ratio of 1:1 by volume to form a lump-free slurry. The bonding coat shall be applied uniformly on the pre-wetted substrate immediately before placing the repair mortar/concrete, |
| 144 | contd..laying roof screed to the required slopes and gradients using M20 grade polymer-modified concrete/mortar prepared in the proportion of 1 : 1.5 : 3 (cement : sand : coarse aggregate). Universal Repair Polymer shall be added at 10% by weight of cement. Placing, compacting, levelling and finishing the screed to the required line, level, and gradient using suitable trowels and finishing tools. The repaired surface shall be kept continuously moist and cured for 7 days, followed by air curing for 4-5 days or as recommended by the manufacturer before application of the waterproofing system.The work shall be carried out complete in all respects in accordance with the manufacturer's specifications and the directions of the Engineer-in-Charge. |
| 145 | M&L for 12mm thick pre-formed filler for expansion joints complete all as specified and as directed by Engineer-in-Charge. |
| 146 | Supply and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner alongwith water proofing compound @ 3% by weight of cement complete all as specified and directed. (WPC should be paid and measured separately) |
| 147 | S&F in repair plain aluminium sheeting, 0.71mm thick alloy 31000 H4 in crumple joints, ridges, hips, valley gutter drip and straight flashing complete all as specified and as directed by Engineer-in-Charge. |
| 148 | Note for Srl item No. 132.00 to 140.00: 1. The work shall be carried out to Building Height upto 12 metres. Necessary arrangement for carrying out the work including labour, equipment, scaffolding, safety appliances transportation of materials shall be provided by the contractor within overall rate quoted against the items of this schedule and no claim whatsover shall be admissible on this account at later stage. Contractors are requested to quote their rates accordingly keeping this aspect in mind.2. The work pertaining to water proofing treatment shall be executed as per MoU between contractor and manufacturer of waterproofing material as per MoU performa attached at Serial page No. 155 to 161. Authorized applicator of the company with trained/ skilled worker will only be allowed to execute the work and the applicator will submit the authorization and experience certificate from the company. 3. The Contractor shall upload with the documents under cover I \\"Memoradum of Understanding\\" (MoU) with at least one of the manufacturers (Pidilite/ Fosroc/ Asian paints/ Sika/ STP) failing which the bid shall not be opened and shall be liable to rejected |
| 149 | 4. The entire quantity of material will be calculated and brought on site as decided by Engineer-in-Charge and will be accepted only post-verification of PVs and challan from company through mail. 5. Material will be kept in the custody of MES rep and will be issued to the authorized applicator as per requirement. 6. Each stage will be properly executed under supervision of company rep and stage passing register will be properly maintained. 7. The contractors shall submit manufacturer generated 10 years warranty card during submission of final bill |
| 150 | 8. A guarantee amount @10% against water proofing treatment will be kept as a reserve till completion of warranty period and will be released thereafter.9. Any deterioration during warranty period will be rectified by the contractor from the manufacturer with whom the MoU is signed, without any financial effect. 10. Ponding tests shall be carried out for 72 hours after completion of roof treatment and ponding shall be done by applicator with company technical rep as per manufacturer's instructions and finally passed as directed by Engineer-in-Charge/GE |
| 151 | Taking down carefully old and unserviceable copper/aluminium point wiring for light/fan/socket or power point complete including fittings such as switches, ceiling rose, pendents, regulators, sockets, bell, etc and making good disturbed surface of walls. floors etc to match with the existing surface complete all as specified and as directed by Engineer-in-Charge. |
| 152 | Point wiring complete with 1.5 sq.mm PVC insulated unsheathed multi-stranded FRLSH copper conductor 1100 Volts grade, ISI marked, drawn through in and including suitable dia of rigid PVC conduit medium grade and conduit accessories, concealed in stone / brick masonry walls, roofs, floors etc, by means of saddles and clips etc, including provision of modular metal flush boxes with modular frame plate and white cover of required modules for housing switches, sockets, regulators etc., including 1.5 sq.mm PVC insulated unsheathed multi-stranded FRLSH copper conductor cable as earth continuity conductor for One light/ bell point controlled by one switch/ one fan point controlled by one switch and fan regulator and connecting to common earth dolly, complete all as specified and as directed by Engineer-in-Charge. Please Enable Macros to View BoQ information |
| 153 | Point wiring complete with 1.5 sq.mm PVC insulated unsheathed multi-stranded FRLSH copper conductor 1100 Volts grade, ISI marked, drawn through in and including suitable dia of rigid PVC conduit medium grade and conduit accessories, concealed in stone / brick masonry walls, roofs, floors etc, by means of saddles and clips etc, including provision of modular metal flush boxes with modular frame plate and white cover of required modules for housing switches, sockets, regulators etc., including 1.5 sq.mm PVC insulated unsheathed multi-stranded FRLSH copper conductor cable as earth continuity conductor for One light/ bell point controlled by one switch/ one fan point controlled by one switch and fan regulator and connecting to common earth dolly, complete all as specified and as directed by Engineer-in-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 03, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 31, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 26 daysAug 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 29 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender