Tender For Comprehensive Misc Repairs To Otm Accn At Nagtalao Under Ge Banar
Tender Value
45 Lakhs
Estimated cost
Bid Submission
22 Jul 2026
15 days left
EMD
90000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jodhpur → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Comprehensive Misc Repairs To Otm Accn At Nagtalao Under Ge Banar
BOQ
| Sl. No. | Item Description |
| 1 | Cleaning and removing all scale and dirt, etc, from tanks exc 250 but n exc 500 liter cacpacity and from mouths of circulating pipes, etc complete all as specified. |
| 2 | Cleaning and removing all scale and dirt, etc, from tanks exc 500 but n exc 1000 liter cacpacity and from mouths of circulating pipes, etc complete all as specified. |
| 3 | S&F in repairs Toilet paper holder with flat recessed type stainless steel complete all as specified. |
| 4 | S&F in repair Bib taps for 15mm bore dia pipe, cast copper alloy cromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified. |
| 5 | M & L in repair 15 mm stop valve (concealed cromium plated, screwed down, high pressure with crutch or butterfly handle screwed for iron pipe or for unions and fixed complete all as specified. |
| 6 | M & L in repair 20 mm gate valve cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed for iron pipe or for unions complete all as specified. |
| 7 | M & L in repair 25 mm gate valve cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed for iron pipe or for unions complete all as specified. |
| 8 | S &F in repairs 15mm bore stop/angle valve of copper alloy, CP with flange complete all as specified. |
| 9 | S &F in repairs Pillar taps(long nose), cast copper alloy chromium plated 15 mm bore, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified. |
| 10 | S &F in repairs Central hole basin mixture cast copper alloy chromium plated fancy type 15 mm bore complete all as specified. |
| 11 | S &F in repairs Mixing valve (wall Mixer) 3 in 1 with flexible tube & hand shower complete chromium plated fancy type 15 mm bore complete all as specified. |
| 12 | S &F in repairs PVC connection 15 mm bore of length 450 mm complete all as specified. |
| 13 | S &F in repairs PVC connection 15 mm bore of length 600 mm complete all as specified. |
| 14 | S&F in repair PVC Flexible waste pipe 32 mm to 40 mm dia with socket for steel sink/WHB upto floor level and length not less than 0.85 Mtr complete all as specified. |
| 15 | S &F in repairs PVC flushing cistern 10 Ltr Capacity including Flush pipe of polyethylene of low or high density or PVC 32 mm dia, for low level cistern complete all as specified. |
| 16 | S &F in repairs CP waste coupling 40 mm size with rubber gasket etc for SS sink complete all as specifeied |
| 17 | S &F in repairs CP waste coupling 32 mm size with rubber gasket etc for WHB etc complete all as specifeied |
| 18 | S&F in repair Fancy type Chromium plated shower roses 125mm size with arm, with or without swivel joints, 15mm bore, including fixing to steel pipe or union. |
| 19 | S&F in repair stainless steel towel ring complete all as specified. |
| 20 | S&F looking mirror (borderless) fancy type fixed with suitable number of stainless steel cup screws (Minimum 4 Nos) complete all as specified. |
| 21 | S&F in repair stainless steel shop dish complete all as specified. |
| 22 | S &F in repairs PTMT body Ball cock /Float Valve 15 mm bore with epoxy coated Aluminum rod & HDPE Ball complete all as specified . |
| 23 | S &F in repairs PTMT body Ball cock /Float Valve 20 mm bore with epoxy coated Aluminum rod & HDPE Ball complete all as specified . |
| 24 | S &F in repairs PTMT body Ball cock /Float Valve 25 mm bore with epoxy coated Aluminum rod & HDPE Ball complete all as directed & specified . |
| 25 | S &F in repairs HDPE flush pipe 32 mm dia of flush cistern to WC complete all as specified. |
| 26 | S &F in repairs GI Nipple 20 mm bore 75mm long for tank connection complete all as specified. |
| 27 | S &F in repairs GI Nipple 25 mm bore 75mm long for tank connection complete all as specified. |
| 28 | S&F in repair health faucet (cast copper alloy cromium plated) with 1200 mm long flexible tube with wall hook complete all as specified. |
| 29 | S &F in repairs mild steel Cromium Plated hygeine wash Jet spray assembly with 1200 mm long flexible tube complete all as specified. |
| 30 | S &F in repairs 15 mm bore angle cock, two way chromium plated cast copper alloy, screwed down, screwed for iron pipe or for brass ferrule complete all as specified. |
| 31 | S &F in repairs 15 mm bore bib taps, two way chromium plated cast copper alloy, screwed down, screwed for iron pipe or for brass ferrule complete all as specified. |
| 32 | S&F in repair 600mmx450mm bevelled edge mirror of selected quality glass 5.5 mm thick, mounted on 6mm thick AC/PVC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified. |
| 33 | S &F in repairs SS chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges all as per sample complete all as specified. |
| 34 | S &F in repairs Shelf of PTMT fixed with and including Chromium plated brass screws andwooden/plastic cleats (Minimum weight 300gms) all as per sample complete all as specified. |
| 35 | S &F in repairs Sheet glass shelf assembly consisting of 6-8 mm thick sheet glass shelf 10-15cm wide with chromium plated bracket guard and railing 60cm long complete all as specified. |
| 36 | S &F in repairs Plastic water closet seat cover, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified. |
| 37 | S &F in repairs 125mm dia CP Grating with or without hole (for waste Pipe) complete all as specified. |
| 38 | S &F in repairs Vitreous China wash hand basin size 550x400 mm size with pedestal with a pair of brackets, waste pipe, waste coupling complete all as specified. |
| 39 | S & F in repair Vitreous china premium/1st quality wash basin (under counter/counter top), white, size 550x400 mm including S&F all accessories as recommended by manufacturer complete fixed in position in all respect as per manufacturer's instructions and all as specified including all Waste fittings, brass,chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engineer-in-charge.Note : The items for counter will be measured and paid separately. |
| 40 | S &F in repairs vitreous China squatting pan, ‘Orissa’ pattern, size 580x440 mm white, with integral foot rests complete all as specified. |
| 41 | S &F in repairs Stainless steel sink with draining board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cantilever brackets, connecting union overall size 915mmx460mm with bowl size 410mm x 330mm x 160mm complete all as specified. |
| 42 | S&F in repairs sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or includingfixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified. |
| 43 | Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified. |
| 44 | Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified. |
| 45 | Taking up or down 25mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified. |
| 46 | S &F 15 mm bore GI tubing medium grade including all connected fittings as elbow., socket , nipple etc complete all as specified. |
| 47 | S&F 20 mm bore GI tubing medium grade including all connected fittings as elbow., socket , nipple etc complete all as specified. |
| 48 | S & F 25 mm bore GI tubing medium grade all as specified. |
| 49 | Refixing 15 mm bore old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified. |
| 50 | Refixing 20 mm bore old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified. |
| 51 | Refixing 25 mm bore old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified. |
| 52 | S &F in repairs sink cock , cast copper alloy cromium plated for 15 mm bore pipe complete all as specified. |
| 53 | Attending complaints of leaking/unsrevicable ,low level flushing cistern, PVC or chinaware for making it fully functtionl and leak proof by repacement the defective parts such as rubber washers , PVC levers,PVC/CP knobs if required complete all as directed and specified. |
| 54 | Attending complaints of internal water supply pipes, fittings and bottles traps for removing of blockages etc of any description incl removing & cleaning of air locks etc. by pressure pump or any other means incl taking down and refixing of pipes & fitting and replacing old unservicable pipes and fitting with new ones in any dia of pipe complete all as specified and as directed. This item includes minor repair items as change of GI socket, elbow or T etc as reqd all as specified & directed at site . Note: New GI pipes replaced if any shall be measured and paid under respective item of this schedule as S&F. |
| 55 | Attending complaints of leaking/unservicable and petty repair to leaking bib taps , pillar taps, stop cock , angle valve ,wall mixture,WHB mixture,bib taps,two way bib taps, , etc of any description incl change of Rubber washer /Jumper sheet etc complete ( all items as washers , spindles , Rubber washer /Jumper sheet etc are included and would not be paid seprately.) |
| 56 | S & F as in repairs 500 liter cacpacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified & removal away from site complete all as specified. |
| 57 | All as above but cap 1000 ltrs |
| 58 | S&F in repair Tank cover for 500 liter /1000 liter water storage tank complete all as specified. |
| 59 | S&F in repairs vitreous china wash down water closet (Pedestal pattern EWC) one piece, coloured, floor mounted coupled closet, including connection to drain (or outgoing pipe), anti-sypohonage pipe etc, with & including WC seat cover coloured closed pattern with flat bottom and cover, vitreous china symphonic action type twin flush flushing cistern of 10 litre capacity with lid, necessary fittings complete all as specified. |
| 60 | S&F in repairs vitreous china wash down water closet EWC, floor mounted coupled with closet, including connection to drain (or outgoing pipe), including WC seat cover closed pattern with flat bottom and necessary fittings complete all as specified. |
| 61 | S&F in repair Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete all as specified. |
| 62 | S&F in repair Vitreous China bowl urinal flat back, full stall, with grating, spreader, waste pipe and union for discharge pipe complete all as specified |
| 63 | Dismantling of cast iron drain pipes (internal dia of pipe 100mm), jointed in cement mortar and taking out of trenches & walls complete all as specified. |
| 64 | Dismantling of cast iron drain pipes (internal dia of pipe of 75 mm), jointed in cement mortar and taking out of trenches & walls complete all as specified. |
| 65 | S & F PVC (SWR) pipes 110 mm single socketed in any length with rubber ring joints, fixed in wall securing with clamp including all fitting etc tee, socket, bend complete all as specified. |
| 66 | S & F of PVC (SWR) pipes 75 mm single socketed in any length with rubber ring joints , fixed in wall securing with clamp including all fitting etc tee, socket, bend complete all as specified. |
| 67 | S&F in repair PVC SWR bends of 110 mm bore complete all as specified. |
| 68 | S&F in repair PVC SWR bends of 75 mm bore complete all as specified. |
| 69 | S&F in repair PVC SWR tee of 75 mm bore complete all as specified |
| 70 | S&F in repair Cast iron 100 mm vent cowl complete all as specified |
| 71 | M&L in repair PVC (SWR) floor trap 75 mm bore , plain with grating including jointing with solvent cement fixed in cement concrete type B-1 (1:2:4) complete all as specified. |
| 72 | Supply for Pipe Supporting Clamping - Single Pipe of dia 25 mm (1\\") down take pipeline fixing done with Clamping System consists of Mono Bracket + U Bolt Rubber Sleeve mounted system running vertically with wall distance 75 mm (3\\"): Pipe Support Clamping made of : 1. Mono Bracket for 25 mm (1\\") pipe having Wall Distance 75 mm (3\\") made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079); material size 48 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result 2000 hrs. 2. U bolt Rubber Sleeve mounted are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit: 1. Mono Bracket for 25 mm (1\\") pipe, Wall distance 75 mm (3\\") - 1 Nos. 2. U Bolt Rubber Sleeve mounted for 25 mm (1\\") GI /UPVC / CPVC pipe Dia. - 1 nos and 3. Fixing Nail Zn coated of thickness 6.5 mm and length 63 mm (2 1/2\\") - 2 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in Chief Engineer Jodhpur Zone Technical Drawing (TD) of Factory Made Pipe Supporting System . REF DRG NO. CEJZ/TD/102. Make : Shaivi or equivalent as approved by GE. |
| 73 | Supply for Pipe Supporting Clamping - Single Pipe of dia 20 mm (3/4\\") down take pipeline fixing done with Clamping System consists of Mono Bracket + U Bolt Rubber Sleeve mounted system running vertically with wall distance 75 mm (3\\"): Pipe Support Clamping made of: 1. Mono Bracket for 20 mm (3/4\\") pipe having Wall Distance 75 mm (3\\") made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079); material size 48 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result 2000 hrs. 2. U bolt Rubber Sleeve mounted are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit: 1. Mono Bracket for 20 mm (3/4\\") pipe, Wall distance 75 mm (3\\") - 1 Nos. 2. U Bol Rubber Sleeve mounted for 20 mm (3/4\\") GI / UPVC/ CPVC pipe Dia. - 1 nos and 3. Fixing Nail Zn coated of thickness 6.5 mm and length 63 mm (2 1/2\\") - 2 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in Chief Engineer Jodhpur Zone Technical Drawing (TD) of Factory Made Pipe Supporting System . REF DRG NO. CEJZ/TD/102. Make : Shaivi or equivalent as approved by GE. |
| 74 | SWR(PVC) OR CI 160 mm Rainwater Pipe ClampSupply for Pipe Supporting Clamping - Single pipe of PVC dia 6\\" (160 mm) down take pipe fixing done with Clamping System consists of Profile Bracket + Continuous Slotted C Channel + U Bolt Rubber Sleeve mounted System running vertically with wall distance 150 mm (6\\"): Pipe Support Clamping made of : 1. Profile Bracket having Wall Distance150 mm (6\\") made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. 2. Continuous Slotted \\"C\\" Channel with ribs to be used of size 300 mm (12\\") made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079) are Hot Dip Galvanzied + Zn Al Flake coated with material 48mm x 3mm. 3. U bolt Rubber Sleeve mounted are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit : 1. Profile Bracket Wall distance 150 mm (6\\") - 2 Nos. 2. Continuous Slotted C Channel of Size 300 mm (12\\") - 1 No.; 3. U Bolt Rubber Sleeve mounted for 160 mm (6\\") CI or PVC Pipe Dia. - 1 No.; and 4. Fixing Nail Zn coated of thickness 6.5 mm and length 63 mm (2 1/2\\") - 4 nos. Fixing Details:Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in Chief Engineer Jodhpur Zone Technical Drawing (TD) of Factory Made Pipe Supporting System . REF DRG NO. CEJZ/TD/102. Make: Shaivi or equivalent as approved by GE. |
| 75 | Four SWR(PVC) 25mm Terrace Floor PipesSupply for Pipe Supporting Clamping - Water supply pipes - 4 no. of dia 25 mm (1\\") CPVC/GI pipeline running on terrace floor fixing done with Pipe Support Clamping System consists of Terrace Floor Clamp + U Bolt Rubber Sleeve mounted system running horizontally above floor level 100 mm (4\\"): Pipe Support Clamping made of: 1. Terrace Floor Clamp - 15\\" Width x 4\\" Height made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079) with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result 2000 hrs. Rubber pad made Nitrile Butadiende Rubber (NBR); Dimension : Base - 54 mm x 54 mm; tapered above to 44 mm x 44 mm and height - 25 mm; inserted with SS304 Hex Flange nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. The clamp and rubber pad are combined together using SS304 Hex Flange Bolt with serration 5/16 x 3/4 (A/F 13 mm) as per DIN 6921. 2. U bolt Rubber Sleeve mounted are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit: 1. Terrace Floor Clamp - 15\\" Width x 4\\" Height - 1 Nos. 2. U Bolt Rubber Sleeve mounted for 25 mm (1\\") CPVC pipe Dia. - 4 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in Chief Engineer Jodhpur Zone Technical Drawing (TD) of Factory Made Pipe Supporting System . REF DRG NO. CEJZ/TD/102. Make : Shaivi or equivalent as approved by GE |
| 76 | Taking down cement plaster from brick work/ Concrete surfaces of walls etc & M&L for 15 mm thick rendering in CM 1:6 finished even & smooth complete all as specified. |
| 77 | Taking down cement plaster from RCC chajja facia, ceiling, wall etc & M&L for 10 mm thick rendering in CM 1:4 finished even & smooth complete all as specified. |
| 78 | M/L two coat of OBD on newly plastered/ unplastered surfaces on wall including preparation of surfaces and 1mm wall care putty complete all as specified. |
| 79 | M&L preperartion of newly plastered surfaces and applying three coat of white wash on RCC chajja/ facia, ceiling etc complete all as specified and directed. |
| 80 | Preparation of new plastered/unplastered surfaces of wall & Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified. |
| 81 | Demolition of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified. |
| 82 | M&L for coloured glazed ceramic tiles 300mmx450mmx6mmthick as per IS 13712 Grade II(a) over 10mm thick rendering in CM (1:4) set and jointed in neat cement slurry and pointed with colour cement to match on vertical brick/ concrete surfaces as in dado (colour and pattern as approved by GE) complete all as specified. |
| 83 | Demolition of Cement concrete in ground floors and pavings n.exc 15 cm thickness below or above ground level) and removing debris out of MOD land complete all as specified. |
| 84 | M&L for 25 mm thick cement concrete type B-1 1:2:4 (using 20mm graded crushed stone aggregate) to receive floor finishes etc complete all as specified. |
| 85 | M&L for coloured non skid ceramic tiles 400mmx400mmx6-7 mm thick as per IS 13712 Grade II(a) in floor etc set jointed and pointed in white or coloured cement to match as in floors over and including 15mm thick screed bed in CM (1:6) complete all as specified. |
| 86 | M&L for Ceramic tiles 7 to 8 mm thick , area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15mm thick screed bed in CM (1:6) complete all as specified. |
| 87 | All as item no. above but as in skirting including 10mm thick backing coat on stone masonry surfaces in CM 1:4 complete all as specified. |
| 88 | M&L for Virified Ceramic double charged tiles 9-10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM (1:6) complete all as specified. |
| 89 | All as item no. above but as in skirting including 10mm thick backing coat on ston masonry surfaces in CM 1:4 . |
| 90 | M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. |
| 91 | M&L for 16-18 mm thick green marble (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade. |
| 92 | M&L for 20-25mm thick machine cut KOTA stone slab as in shelves (Single piece) fixed in walls machine cut, laid over cement and jointed with grey cement slurry with pigment to match the shade of the slab, incl rubbing and Mirror polishing all as specified. |
| 93 | M&L for Machine cut kota stone slab flooring 20-25mm thick over and including 15mm thick screed bed in CM (1:6) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete |
| 94 | M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete |
| 95 | M&L for 40 mm thick PCC (1:2:4) type B1 using 20mm graded stone aggregate as in floor , hard standing flooring finished even and smooth without using extra cement |
| 96 | M&L for 75 mm thick PCC (1:3:6) type C1 using 20mm graded stone aggregate as in plinth protection finished complete including forming joints in 2 mtr interval and filled with bitumen mastic all as specified. |
| 97 | M&L for 100 mm thick Cement concrete type D- 2, 1:4:8 (40mm graded aggregate) complete all as specified. |
| 98 | Providing and laying 80mm thick factory made chamfered edge cement concrete paver block (rubberised finish) of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete. |
| 99 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block (rubberised finish) of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; |
| 100 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete. |
| 101 | Taking down existing roof treatment in any postion and any thickness on RCC roof slab and debries to be disposed out of MOD land |
| 102 | M&L for 10mm thick cement mortar 1:4 on roof surfaces and applying two coats of polyurethene (PU) acrylic based water proofing liquid compound over and including a coat of diluted elastomeric self primer and reinforcement fabric sheet as per manufacturer's instruction to stop leakage /seepage from roof/wall complete all as specified and directed by Engineer-In-Charge. Note : (i) Quated rate shall be deemed to be included for the work in building/ structure of any height. (ii) The procurement of material and execution of the work of water proofing treatment shall be got executed from one of the following manufacturers approved by GE : M/S Asian paints Ltd (Damp proof ultra) or equivalent |
| 103 | M&L for PCC 1:2:4 type B1 using 20mm graded stone aggregate in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings,levelling course, kneelers, apex stones, bed plates, kerbs not provided for, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed complete |
| 104 | Dismantaling cement Concrete of any description and in any position not otherwise specifically provided for |
| 105 | M&L for 35 mm thick pre-cast cement concrete louvres and jallies (measured solid) in cement concrete (1:2:4) type B-0 using 12.5mm graded stone aggregate including all moulding and set in cement mortar 1:4 complete all as specified. |
| 106 | M/L for precast cement conc. Post in 1:3:6 type C1 using 20mm graded stone aggregate set in CM 1:4 complete all as specified. |
| 107 | Demolition of stone masonry /block walling built in cement mortar complete all as specified. |
| 108 | M&L for squarred rubble walling Jodhpur type regular coursed well bonded, bedded and solidly hearted built in cement mortar 1:6 complete all as specified. |
| 109 | Extra over squared rubble stone walling Jodhpur type regular course for hammer dressing to face of stone with max depression on face from a straight edge not exc 20mm and dressing complete all as specified. |
| 110 | M&L for precast cement concrete solid building blocks type B1 1:2:4 (20mm graded stone aggregate) or slabs 10cm thick (with plain or interlocking joints as directed) setting in 1:6 cement mortar, complete, in walls complete all as specified. |
| 111 | M&L for Pre-cast cement concrete block masonry with solid blocks, type B1 1:2:4 (20mm graded stone aggregate) exc. 10 cm in width and setting in cement mortar 1:6 complete all as specified. |
| 112 | S&F as in repairs stainless steel plate rack of size 30\\"x24\\"x10\\" size as per trade pattern fabricated with 0.50mm thick stainless steel sheet suitable for stacking 15 plates with hooks /fittings complete all as per sample complete all as specified. |
| 113 | S&F in repair Decorative type curtain rod stainless steel finish MS pipe 22 to 25 mm dia as per sample superior quality complete and incl brackets and Decorative fincals (round type with mirror optic finish) trade pattern for decorative type curtain rods suitable for holding & end cover complete all as specified. |
| 114 | S&F in repairs PVC Cabinet mirror of size ( 355mmx 455mm ) of selected quality glass and fixed to plugs with chromium plated brass screws and cup washers complete all as specified. |
| 115 | Taking down Chowkhat or frame with shutter (without taking out shutter from frame) of area exc 1.5sqm but not exc. 4 Sqm each complete. |
| 116 | Taking down shutter of any description area exc 1 Sqm but n. exc 2 Sqm each complete. |
| 117 | Taking down steel windows / ventilator with frame of any description and any size complete |
| 118 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 119 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) |
| 120 | Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., Fe 410-W (Gde E-250) quality-A complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete |
| 121 | S&F of 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels,Both face is covered with decorative face veneer with lipping/frame to match |
| 122 | S&F 2nd class hard wood 35 mm thick glazed and skeleton shutters open rebated and prepared to receive glass, gauge, etc divided into squares by Rails and styles , with plain chamfered or rounded mitered and rebated size of members of shutters as specified in SSR Part-I, section 8, clause 8.24 (a) complete. |
| 123 | Framed work such as grills, gratings, cooler stand etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 |
| 124 | S & F galvanised MS wire cloth 0.56 mm nominal dia of wire & 1.18 mm average width of apperture fixed complete all as directed & specified. |
| 125 | S&F in repairs galvanised ms wire cloth 0.56mmm nominal dia of wire and average width of aperature 1.18mm complete all as specified. |
| 126 | S&F of 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels,Both face is covered with decorative face veneer with lipping/frame to match complete all as specified. |
| 127 | Demolition of cement Concrete of any description and in any position not otherwise specifically provided for and complete removal to debris outside the defence land or low laying area complete all as specified. |
| 128 | S&F 100mm size SS butt hinges (ISI Marked) complete all as specified. |
| 129 | S&F 300mm long Mild steel sliding door bolt plate type stove enamelled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts,four on bolt plate and two on tapple plate and fixed complete all as specified. |
| 130 | S&F 200mm MS barral tower bolts stove enamelled black with bright bolt and fixed complete all as specified. |
| 131 | S&F in repairs 200mm MS barral tower bolts stove enamelled black with bright bolt and fixed complete all as specified. |
| 132 | S&F 150mm MS pressed handle oval type stove enamelled black complete all as specified. |
| 133 | S&F in repairs, 150mm MS pressed handle oval type stove enamelled black complete all as specified. |
| 134 | S&F in repairs 140 mm size best quality Floor door stopper of aluminium alloy body and tongue, anodised & hard rubber shoe all as per sample |
| 135 | M&L Preparation of new wooden surface exceeding 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete. |
| 136 | S&F solar control film of 25 micron reflective type sticked with glass as per manufacturer instuction in any size in each pane complete all as specified. |
| 137 | Supply and fixing in repairs Aluminium Anodised extruded section ISI Marked tower bolt of size 200 mm complete all as specified. |
| 138 | Supply and fixing in repairs Anodised aluminium extruded section ISI marked door handles size 150 mm complete all as specified. |
| 139 | S& F in repairs MS sliding door bolts 300mm long, plate type, stove enamelled black, with bright bolt not less than 12 mm dia with and incl a mini of 6 bolts and nuts four on bolt plate and two on staple plate and fixed complete all as specified. |
| 140 | S & F in repairs mild steel 300mm ordinary rat tail rod pattern spring incl roller and roller plat complete all as specified. |
| 141 | Supply and fixing in repairs Mild Steel Butt hinges medium weight cold rolled 100mm size complete all as specified. |
| 142 | S&F in repairs Stainless Steel medium weight 100mm size Butt hinges complete all as specified. |
| 143 | S&F in repair cast iron body door closer hydraulic regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified. |
| 144 | S&F in repair Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified. |
| 145 | S & F in repairs 40mm dia cupboard knobs fixed the screw and washer of MS bright finished complete all as specified. |
| 146 | S & F in repairs Mild steel body peg stays 250 mm long (minimum) to steel windows & vents complete all as specified. |
| 147 | S & F in repairs Mild steel body window handles (Left or right) any size to steel windows & vents complete all as specified. |
| 148 | S & F in repairs Door seal as per trade pattern with powder coated aluminium strip 25-30 mm width length having suitable dia holes (for fixing screws) & synthetic strip at bottom to avoid entry of dust etc fixed all as specified & directed . |
| 149 | Hacking out old broken glass any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing complete all as specified. |
| 150 | S & F 3mm thick Plain sheet glass panes cut to size required n exc 0.50 sqm each complete all as specified. |
| 151 | S & F 4mm thick figured glass pin headed type n exc 0.50 sqm each complete all as specified. |
| 152 | Supply & fix continuous paino hinges 40 mm width of flap mild steel body electro galvanised finish all as directed & specified. |
| 153 | S&F of 100 mm long Hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified. |
| 154 | Resucuring /easing and adjusting shutters without taking down of any description and in any position area exc 1 sqm but n exc 2 sqm complete all as specified. |
| 155 | Resucuring /easing and adjusting to steel windows / vents incl necessary welding rivetting etc complete all as specified. |
| 156 | S&F powder coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified (min thickness of powder coating 50 micron) complete all as specified. |
| 157 | S&F powder coated Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified. (min thickness of powder coating 50 micron) complete all as specified. |
| 158 | S&F power coated Anodised aluminium window and ventilator shutters(Thickness of powder coating not less than 50 micron), side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified |
| 159 | S&F 5.5mm thick Sheet glass ordinary quality glass and glazing in any size in each pane complete all as specified. |
| 160 | S&F Anodised aluminium powder coated decogrill for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete shall as specified. |
| 161 | S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified. |
| 162 | S&F in repairs brass mortice lock, vertical type, size 65mm, 4 Levers with escutcheon plates & two keys fixed in aluminium frame complete all as specified. |
| 163 | Repairs to joinery (wooden/steel) iron/aluminium mongery, pelmet box, door springs etc requiring carpentry work and carrying out minor repairs such as tightening of screws/nails, minor adjustment of joinery, door etc. including petty repairs material like screws/nails, plug etc. to make it functional complete all as specified. Please Enable Macros to View BoQ information |
| 164 | Repairs to joinery (wooden/steel) iron/aluminium mongery, pelmet box, door springs etc requiring carpentry work and carrying out minor repairs such as tightening of screws/nails, minor adjustment of joinery, door etc. including petty repairs material like screws/nails, plug etc. to make it functional complete all as specified. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 03, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 22, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 15 daysJul 24, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 17 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender