Tender For Special Repair Of Building No U-47, 3 Vikas Est No 22 At Chakrata.
Tender Value
34.47 Lakhs
Estimated cost
Bid Submission
24 Jul 2026
19 days left
EMD
68940
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Dehradun → Uttarakhand
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repair Of Building No U-47, 3 Vikas Est No 22 At Chakrata.
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling of plain or corrugated steel sheeting any gauge, thickness, including Naintal or similar pattern roof coverings of any description etc complete all as specified and directed. |
| 2 | Dismantling wall and ceiling board fibre, pulp insulation etc or insulation boards any thickness including cover fillets complete all as specified and directed. |
| 3 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises and removing the debris outside from defence land complete all as specified and directed. |
| 4 | Dismantling unframed timber scantling 40 sqm and over in section, in any position complete all as specified and directed. |
| 5 | Taking down chowkhats or frames exc 1.50 and n.exc 4 Sqm each (without talking off shutters from the frame) complete all as specified and directed. |
| 6 | Taking down chowkhats or frames not exc 1.50 Sqm each (without talking off shutters from the frame) complete all as specified and directed. |
| 7 | S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 8 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 9 | S & F 4 mm thick of size 600x600mm HSPC (high pressure Steam Cured) pre-primetered self embossed, textured designer board E-Board Classic to be fixed GI grid/section size 600mmx600mm with main runner 38x24x0.9mm thick ,cross tee 28.6x24x0.9 mm and wall angle 19x19x0.9 mm duly suspended with 2mm dia SS bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any size complete all as specified and directed. |
| 10 | M&L for 25mm thick PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate as in sub base of floor finished rough to receive floor finishes complete all as specified and directed. |
| 11 | M&L for dark shade/coloured vitrified ceramic tiles 10mm thick area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, each as in floors laid over and including 15mm thick screed bed or bedding layer of mortar for laying floor finishes in CM (1:6) set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 12 | All as per Item No.11 above but on vertical surfaces such as in skirting, dado, risers to steps fixed over and including 10 mm thick bedding layer in CM 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 13 | M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed. |
| 14 | M&L for coloured Glazed ceramic tiles in vertical surface such as in skirting, dado etc of size 350mmX250mmX 7 to 8mm /450mmX 350mmX 7 to 8mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles fixed over and including 10mm thick rough cement plaster as in backing coat to receive tiles in CM 1:4 complete all as specified and as directed. |
| 15 | M&L for moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed. |
| 16 | Demolition of cement or lime concrete (unreinforced) in ground floors and Pavings not exc 15 cm thick (below or above ground level ) and removing the debris outside from defence land complete all as specified and directed . |
| 17 | M&L for 75 mm thick PCC 1:3:6 type C-2 (using 40 mm graded stone aggregates) as in sub base, plinth protection, path/steps etc complete all as specified and directed. |
| 18 | M&L for chequered cement concrete tiles of size 30 cm X 30 cm X 25 mm thick, set, jointed and pointed in neat cement slurry and pigments as in floors laid over and including 15mm thick screed bed or bedding layer of mortar in CM 1:6 for laying floor finishes/ tiles complete all as specified and directed. |
| 19 | M&L for rolled mild steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe 410-W (Gde-E 250) quality-A complete all as specified and directed. |
| 20 | S & F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 10cm and n exc 15cm long - 11 to 15mm diameter of neck complete all as specified and and directed. |
| 21 | S&F powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, complete all as specified and directed. |
| 22 | S&F 4 mm thick anodised aluminium composite panel fixed in aluminium frame including necessary rubber beading, jointing cleats and all necessary items to fix with frame complete all as specified and directed. |
| 23 | Demolition of brick work or stone boulder masonry built in cement mortar or cement lime including all quoins, arches, pillars etc, but excluding ashler facings, dressed stonework and precast concrete articles complete all as specified and as directed. |
| 24 | M&L for brick work with sub class 'B' bricks built in CM 1:6 straight or curved on plan & exc 6 m mean radius with old size bricks complete all as specified and directed. |
| 25 | Taking down cement plaster and raking out joints, hacking for key,scrubbing down with water built in cement mortar complete all as specified and directed. |
| 26 | M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces in CM (1:6) and finished even and smooth (without using extra cement) complete all as specified and directed. |
| 27 | M&L for rendering 15mm thick in CM 1:4 other than fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed. |
| 28 | M&L for preparation of new plastered surface of wall and applying two or more coats of 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer of required shade and colour over and including a layer of putty 1.0 mm thick over plastered surface to prepare the surface even and smooth complete all as sepecified and directed. |
| 29 | M&L for preparation of new plastered surface of walls including cornices, pilasters etc and finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade on new work two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed. |
| 30 | M&L for preparation of new surfaces of steel and iron work of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint any tint over a coat of red oxide primer complete all as specified and directed. |
| 31 | S&F second class hardwood 35 mm thick plain, framed, panelled shutter (two panels) with lock rail and panel of 9mm thick B.W.P commercial ply or 12mm thick veneered particle board with commercial veneering on both faces; size of rail and stile as per IS: 1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and directed. |
| 32 | S &F 35mm thick 2nd class hardwood glazed and skeleton shutters open rebated and prepared to receive glass gauze etc divided into squares, with plain, chamfered or rounded mitred and rebated sash bars any number edges of framing plain, chamfered or rounded, fitted with cut and metered beads for securing glass etc size of members of shutters as specified in SSR Part I Sec 8 clause 8.23 (a) complete all as specified and directed. |
| 33 | S & F galvanised wire cloth, 0.63 mm nominal dia of wire and average width of aperature 1.4mm and fixed with tinted tacks or galvanised wire staples as in fly proof window and door complete all as specified and directed. |
| 34 | S&F 100mm size Stainless steel butt hinges complete all as specifed and directed |
| 35 | S&F Stainless steel barrel tower bolt 200mm long of extruded section complete all as specified and directed. |
| 36 | S&F Stainless steel sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or castaluminium alloy and fixed Length of bolt in 250 mm complete all as specified and directed. |
| 37 | S & F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor, overall length of cover plate 150mm complete all as specified and directed |
| 38 | M&L for preparation of new wooden surfaces of any description, over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 39 | M&L for preparation of old previonusly treated wooden surfaces of any description, over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 40 | S&F in repairs vitreous china squatting Pan of Orrisa pattern size 580X440 mm white with integral foot rest concerte bedding and making good floor complete all as specified and directed. |
| 41 | S&F in repairs PVC valveless, syphonic action type flushing cistern 10 ltrs capacity low level, with inlet, ball valve float, flush pipe and handle including brackets complete all as specified and directed. |
| 42 | S & F in repairs vitreous china wash hand basin, flat back size 450 x 300mm white with pedastal including MS brackets (excluding taps, saste, chain and plug and procelain stopper) etc complete all as specified and directed. |
| 43 | S & F in repair 15mm dia pillar taps, cast copper alloy, with capstan heads, chromium plated, Fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed. |
| 44 | S&F in repairs 32 mm bore dia of discharge pipe waste coupling of PTMT (half or full threaded). (Minimum weight 32 mm -45 gms) complete all as specified and directed. |
| 45 | S&F bevelled edge mirror of selected quality glass, 5.50mm thick of size 600mmx450mm mounting on 6 mm thick AC building board or commercial ply wood and fixed to wooden plugs with chromium plated brass screws and cup washers, with and including aluminium edging around of mirror complete all as specified and directed. |
| 46 | S&F 15mm bore PVC connection 450 mm long with two brass chromium plated brass nuts and PVC washers complete all as specified and directed. |
| 47 | S&F in repairs 15mm bore Stop/angle cock, fancy type, cromium plated with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed. |
| 48 | S&F in repairs soap dish, vitreous china white, approximate size 160 x 160 x 90mm complete all as specified and as directed. |
| 49 | S & F in repairs 15mm dia bib tap cast copper alloy chromium plated with crutch or butterfly handle, screwed down, scrwed for iron pipe or for brass ferrule complete all as specified and directed. |
| 50 | Taking up or down 15 mm bore old steel tubing and connections, including disconnection of fittings from tubing including cleaning for re-fixing or removal from site complete all as specified and directed. |
| 51 | S&F 15 mm bore tubes medium grade galvanised with and incl all GI fitting (such as bends, elbows, Tees, connectors, short pieces, back nuts, unions, caps and plug etc ) and fixed to wall and ceiling or laid in/on floor complete all as specified and directed. |
| 52 | S&F in repairs brass chromium plated 'D' type tubular towel bar of 20mm dia fancy type 60cm long between flanges complete all as specified and directed. |
| 53 | S&F grating doom 100mm dia of PTMT (Minimum weight 25 gms) complete all as specified and directed. |
| 54 | S & F draperly rod/Harrison rails of CP of 25 mm dia with fixing brackets, stops rollers and rings etc complete all as specified and directed. |
| 55 | Taking down carefully existing aluminum/copper surface/concealed point wiring (light, fan, socket or power point) complete of any description including fitting such as switches, ceiling roses, lamp holder, regulators, sockets, wooden boards, laminated sheets from sunken boxes, boards, shades light fitting etc and making good the disturbed surfaces in CM 1:3 of walls, floors, ceiling etc including distempering to match with existing surfaces complete all as specified and directed. Please Enable Macros to View BoQ information |
| 56 | Taking down carefully existing aluminum/copper surface/concealed point wiring (light, fan, socket or power point) complete of any description including fitting such as switches, ceiling roses, lamp holder, regulators, sockets, wooden boards, laminated sheets from sunken boxes, boards, shades light fitting etc and making good the disturbed surfaces in CM 1:3 of walls, floors, ceiling etc including distempering to match with existing surfaces complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 03, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 24, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 19 daysJul 27, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 22 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender