Tender For Construction Of Proposed Vulnerable Witness Deposition Centre At Khatra Sub-Divisional Court Under Bankura Division, Pwd.
Tender Value
2.27 Crore
Estimated cost
Bid Submission
29 Jul 2026
20 days left
EMD
4.54 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bankura → West Bengal
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Construction Of Proposed Vulnerable Witness Deposition Centre At Khatra Sub-Divisional Court Under Bankura Division, Pwd.
BOQ
| Sl. No. | Item Description |
| 1 | Part-A Civil WorkSurface Dressing of the ground in any kind of soil including removing vegetation inequalities not exceeding 15 cm depth and disposal of the rubbish within a lead upto 75 m as directed |
| 2 | Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. Depth of excavation not exceeding 1,500 mm. |
| 3 | Depth of excavation for additional depth beyond 1,500 mm. and upto 3,000 mm. but not requiring shoring. |
| 4 | Add extra for excavation in morum soil |
| 5 | Filling in foundation or plinth by FINE sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity) |
| 6 | Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand. |
| 7 | Cement concrete with graded stone ballast (40 mm size excluding shuttering)In ground floorPakur Variety1:3:6 proportion. |
| 8 | Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant IS codes.Using Pakur Variety stone chips |
| 9 | Supplying and laying Polythene Sheet (150gm / sq.m.) over damp proof course or below flooring or roof terracing or in foundation or in foundation trenches. |
| 10 | Pre-Constructional Anti-termite measures:Anti termite treatment to the top surface of the consolidated earth within plinth walls with chemical emulsion by admixing chloropyrofos emulsifiable concentrates (1% concentration) with water by weight at the rate of 5 Litres per sq. m. of the surface before sand bed or sub-grade is laid. Holes upto 50 mm. to 75 mm. deep at 150 mm. centre to centre both ways shall be made with 12 mm, diameter mild steel rod on the surface to facilitate saturation of the soil with the chemical emulsion. The work shall be carried out as per specification described in para 6.4 of code IS- 6313 (part -II) 1981. ( Mode of measurment will be per Sq.m of plan area of plinth treated.) |
| 11 | Pre-Constructional Anti-termite measures:(d) Treatment to the back filling of R.C.C. foundation with chemical emulsion by admixing chloropyrofos emulsifiable concentrate (1% concentration) with water by weight at the rate of 7.5 ltr. per sq.m. of the vertical surface of the substructure of each side of the foundation. The work shall be carried out as per specification as described in para 6.3.1 of code IS- 6313 (part-II) 1981 (Mode of measurement will be per sq.m. of vertical area of foundation treated). |
| 12 | Brick work with 1st class bricks in cement mortar (1:6)In foundation and plinth |
| 13 | Brick work with 1st class bricks in cement mortar (1:6)In SuperstructureIn Ground floor |
| 14 | In First floor |
| 15 | In Second floor |
| 16 | 125 mm. thick brick work with 1st class bricks in cement mortar (1:4)In Ground floor |
| 17 | In First floor |
| 18 | Extra for using approved H.B netting in every third layer in 125 mm. thick brick work with 1st class bricks in cement mortar (1:4)In any floor |
| 19 | 40 mm. thick damp proof course with cement concrete (1:1.5:3) (with graded stone chips 20 mm nominal size) with water proofing compound of approved brand @ 0.2% weight of cement including cost of materials over two coats of non toxic acrylic polymer modified cementitious waterproofing slurry coat complete [cost of water proofing compound and non toxic paint to be paid seperately) for underground water retaining structures.[water proofing as per item no 9 and non toxic paint as per item no. 8 (b) of subhead C of Section 'C' ] |
| 20 | Controlled Cement concrete with well graded stone chips (20 mm nominal size) excluding shuttering and reinforcement with complete design of concrete as per IS : 456 and relevant special publications, submission of job mix formula after preliminary mix design after testing of concrete cubes as per direction of Engineer-in charge. Consumption of cement will not be less than 300 Kg of cement with Super plasticiser per cubic meter of controlled concrete but actual consumption will be determined on the basis of preliminary test and job mix foumula. In ground floor and foundation.[using concrete mixture]M 25 GradeUsing Pakur Variety stone chipsIn Ground Floor |
| 21 | Controlled Cement concrete with well graded stone chips (20 mm nominal size) excluding shuttering and reinforcement with complete design of concrete as per IS : 456 and relevant special publications, submission of job mix formula after preliminary mix design after testing of concrete cubes as per direction of Engineer-in charge. Consumption of cement will not be less than 300 Kg of cement with Super plasticiser per cubic meter of controlled concrete but actual consumption will be determined on the basis of preliminary test and job mix foumula. In ground floor and foundation.[using concrete mixture]M 25 GradeUsing Pakur Variety stone chipsIn First Floor |
| 22 | M 25 GradeUsing Pakur Variety stone chipsIn Second Floor |
| 23 | Controlled Cement concrete grade mix with well graded stone chips (20 mm nominal size) including adequate plasticiser & excluding shuttering and reinforcement with complete design of concrete as per IS : 456 and relevant special publications, submission of job mix formula after preliminary mix design after testing of concrete cubes as per direction of Engineer-in charge. Consumption of cement will not be less than 360 Kg of OPC [43/53 grade ] cement with Super plasticiser per cubic meter of controlled concrete but actual consumption will be determined on the basis of preliminary test andjob mix foumula. In ground floor and foundation. [using concrete mixture] With Pakur VarietyM 40 Grade of Concrete |
| 24 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. For works in foundation and upto roof of ground floor/upto 4 mTor steel/Mild SteelSAIL/ TATA/RINL |
| 25 | In First FloorTor steel/Mild SteelSAIL/ TATA/RINL |
| 26 | In Second FloorTor steel/Mild SteelSAIL/ TATA/RINL |
| 27 | Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor)25 mm to 30 mm shuttering without staging in foundation |
| 28 | Steel shuttering or 9 to 12 mm thick approved quality ply board shuttering in any concrete workIn Ground Floor |
| 29 | Steel shuttering or 9 to 12 mm thick approved quality ply board shuttering in any concrete workIn First Floor |
| 30 | Steel shuttering or 9 to 12 mm thick approved quality ply board shuttering in any concrete workIn Second Floor |
| 31 | Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work)With earth obtained from excavation of foundation. |
| 32 | Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals).Sal : MalayasianIn Ground Floor |
| 33 | Sal : MalayasianIn First Floor |
| 34 | Sal : MalayasianIn Second Floor |
| 35 | Supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per direction. (Cost of concrete will be paid separately) 40mm X 6mm, 250mm Length |
| 36 | Panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings.In ground floor.(In case of non-supply of single plank, penal rate of reduction of 20% will be made)50mm thick shutters with 25mm thick panel of size 30 to 45 cm1st class best Indian teak. |
| 37 | In second floor. |
| 38 | Supplying solid flush type doors of deluxe decorative (both side) quality, conforming to I:S 2202 timber frame consisting of top and bottom rail and side styles of well seasoned timber 65mm wide each and the entire frame fitted with 27.5mm wide battens places both ways in order to made the door of solid core and internal lipping with teak, mahogony or rose wood approved decorative veneers using phenol formaldehyde as glue etc. complete, including fitting, fixing the shutters in position but excluding the cost of hinges and other fittings 35mm thick shutters (single leaf)In ground floor: |
| 39 | 35mm thick shutters (single leaf)In First floor: |
| 40 | Brass hasp bolt of approved quality fitted and fixed complete (oxidised) with 16mm dia rod with centre bolt and round fitting.300mm long. |
| 41 | Anodised aluminium barrel / tower / socket bolt (full covered) of approved manufactured from extruded section conforming to I.S. 204/74 fitted and fixed with cadmium plated screws:150mm long x 12mm dia. bolt. |
| 42 | 225mm long x 12mm dia. bolt. |
| 43 | Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete:With continuous plate base (Hexagonal/ Round rod)150 mm grip x 12 mm dia rod. |
| 44 | Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark100mm. X 58mm. X 1.90mm. |
| 45 | Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark100mm. X 75mm. X 3.50mm. |
| 46 | M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugsIn ground floorGrill weighing above 16 Kg./sq.mtr and above |
| 47 | M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugsIn First floorGrill weighing above 16 Kg./sq.mtr and above |
| 48 | In Second floorGrill weighing above 16 Kg./sq.mtr and above |
| 49 | Collapsible gate with 40mm x 40mm x 6mm Tee as top and bottom guide rail, 20mm x 10mm x 2mm vertical channels 100mm apart in fully stretched position 20mm x 5mm M.S. flats as collapsible bracings properly rivetted and washered including 38mm steel rollers including locking arrangements, fitted and fixed in position with lugs set in cement concrete and including cutting necessary holes, chasing etc. in walls, floors etc. and making good damages complete.(Payment will be made on the area of the gate covered by two guard rails and two extreme channels)In ground floor. |
| 50 | M.S. works in brackets made from flats, angles, tees etc. to sizes specialy bent, twisted, forged; making holes drilled and fitted to rafter of trusses with necessary bolts, nuts, washer or screws etc. (length of straight not less than 230 mm) |
| 51 | Supplying profiles of required section made of Aluminium Alloy Extrusions conforming to IS: 732-1983 and IS: 1285- 1975; Annodized (with required film thickness and specified colour / natural) matt finished conforming to IS: 1868-1983 for fabrication of composit door, sliding & casement windows, partitions, formed of basic sections of any ISI embossed / certified make and brand as per direction of Engineer - In- Charge. (Payment will be made on finished length of the work).15 Micron colour annodizing.4- track sliding windowBottom frame |
| 52 | 15 Micron colour annodizing.4- track sliding windowTop and side frame. |
| 53 | 15 Micron colour annodizing.Shutter for all track sliding window.Bottom & Top member. |
| 54 | 15 Micron colour annodizing.Shutter for all track sliding window.Style side member. |
| 55 | 15 Micron colour annodizing.Shutter for all track sliding window.iii) Interlock member. |
| 56 | 15 Micron colour annodizing.Louvered window.Top, bottom and side member. |
| 57 | 15 Micron colour annodizing.Louvered window.Louvered Section. |
| 58 | 15 Micron colour annodizing.h) Louvered window.Cleat angle ( Non-annodized). |
| 59 | 15 Micron colour annodizing.Fixed glazing.Top, bottom and side member. |
| 60 | 15 Micron colour annodizing.Fixed glazing.Mullion. |
| 61 | 15 Micron colour annodizing.Fixed glazing.Glazing clip. |
| 62 | 15 Micron colour annodizing.Movable door shutter.Door frame. (Top & sides). |
| 63 | 15 Micron colour annodizing.Movable door shutter.Shutter :Top rail. |
| 64 | 15 Micron colour annodizing.Movable door shutter. Shutter :Bottom rail. |
| 65 | 15 Micron colour annodizing.Movable door shutter.Shutter :Lock rail |
| 66 | 15 Micron colour annodizing.Movable door shutter.Shutter :Door vertical. |
| 67 | 15 Micron colour annodizing.Movable door shutter.Shutter :Glazing clip. |
| 68 | Labour charge for fabrication and installation of composite door, window, partitions made from annodized extruded alloy aluminium sections for the following units:-Glazed aluminium sliding windows made of extruded and annodized alloy aluminium sectios, fabrications, including cutting to proper shape and size, drilling and aligning of window shutter frame fitted with in built locking arrangements, sliding rollers and other necessary fittings, fixture, adhesives and joineries along with extruded neoprine or EPDM gasketing in between window frame and masonry work (walls, column, beam.lintels etc.) as well as between glass and shutter frame for fixing glass and Polysulphide sealant and in between shutter and window frame where necessary including cutting to requisite size and fixing glass as per drawing, specification and direction of EIC. The rate includes the hire charge of all tools and plants, including all incidental charges, adhesive, joineries such as screw, cleat angle etc. but excluding the cost of extruded aluminium sections, glass, neoprene / EPDM gasket, locking arrangement and rollers.ii ) 3 /4 track sliding window. |
| 69 | Fixed glazing. |
| 70 | Louvered window. |
| 71 | Labour charge for fabrication and installation of composite door, window, partitions made from annodized extruded alloy aluminium sections for the following units:-(B) Partly glazed partly panelled or fully glazed single leaf alunminium swing door made of extruded and annodized alloy aluminium sections, fabrication including cutting to proper shape and size, drilling and aligning, fitted with heavy duty hydraulic action floor sping placed in the floor with mending damages,with top pin assembly of approve make and brand, fitted with in built locking arrangement, flush bolt, glazing clips and all other necessary fittings, fixtures, adhesives and joineries, cutting glass of approved make to requisite shape and size fitting with dry set neoprene or EPDM gasketing, cutting to requisite shape and size panel board (prelaminated particle block) fixing them with glazing clips as per drawing, specification and direction of Engineer in charge. The rate includes the hire charge of all tools and plants, adhesive, joineries such as screw, cleat angle etc. but excluding the cost of extruded alumium sections, glass, panel boards neoprene / EPDM gasket, locking arrangement, weather gasket / wool pile, floor spring, top pin, handle, tower bolt, glazing clips etc. (10% rate reduction has to be made for swing doors or partitions where floor sping is not used. 10% enhancement of rate is to be made where door frame of extruded aluminium sections has to be fitted and fixed to masonry wall. 5% rate enhencement may be allowed for double leaf swing door. Payment shall be made for the shutter area only exept where door frame is fixed the entire opening shall be taken to consideration.Payment for door frame sections are to be paid seperately). |
| 72 | Supplying PVC rollers for sliding windows as per direction of Engineer in charge. |
| 73 | Supplying maruti lock (100mm) |
| 74 | Supplying EPDM gusket of approved make and brand as per direction of Engineer in charge.'U' shaped EPDM gasket for frames. |
| 75 | Filling the gap in between aluminium frame & adjacent RCC / Brick/ Stone work by providing weather silicon sealant over 6mm dia backer rod of approved quality as per architectural drawings and direction of Engineer-in-Charge complete.Upto 5 mm depth and 5 mm widthGround Floor |
| 76 | Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987;Coloured, toughened glass conforming to IS: 2553-1992 (part-II)6mm thick |
| 77 | Coloured, toughened glass conforming to IS: 2553-1992 (part-II)10mm thick |
| 78 | Supplying, fitting and fixing fibre reinforced polymer (FRP) Composite door frame as per approved section with glass fibre reinforced plastic moulded skins and a special sandwich core, so as to impart monolitaheic composite structure as per approved technology of Department of Science and Technology (DST) to safisfy IS: 4020 door testing performance criteria.66mm x 90mmIn Ground Floor |
| 79 | Supplying, fitting & fixing fibre reinforced polymer (FRP) Composite door shutters as per approved design with glass fibre reinforced plastic moulded skins and a special sandwich core, so as to impart monolitaheic composite structure as per approved technology of Department of Science and Technology (DST) to satisfy IS:4020 door testing performance criteria.In ground floor..32 mm thick |
| 80 | In First floor.32 mm thick |
| 81 | Godrej Hydraulic door closer fitted and fixed complete. Heavy type |
| 82 | Steel body foot-door holder. |
| 83 | Supplying, fitting fixing Godrej type hydraulic (oil check) floor door spring, heavy duty double action with brass shoe, brass top centre aluminium top cover etc. complete set as per direction of Engineer-in-charge. |
| 84 | Supplying 'Godrej' mortice lock chromium plated with keys 6 levers including fitting & fixing complete |
| 85 | Supplying, fitting & fixing Stainless Steel 'D' or 'H' type of size 300 mm x 19 mm tubular Handle with Grade 304, CE certified, marked & conforming to EN - 1154, of approved quality of reputed brand as per direction of Eingineer-in- Charge fitted and fixed complete including all incidental charges. |
| 86 | Providing and fixing exterior quality Aluminium Composite Panel (ACP) wall cladding on existing Al. /MS frame work with GI brackets, ACP fixed on the existing frame work by folding the edges of ACP panel (Engraving the rear surface of ACP sheet) with CP angles, cleats and strainless Steel screws forming groves at the periphery of ACP panel. Such grooves filled with foam and silicon sealant etc. complete with all materials (but including the cost of silicon sealant), labour, scaffolding and all other incidental charges complete in all respect as per specification and direction of Engineer-in-charge. (Mode of payment is on finished surface area of ACP)4mm thick (0.50mm Al.+3.0mm LDPE +0.50mm Al. PVDF coating) |
| 87 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding / staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface]With 1:6 Cement mortar, 20 mm. thick plaster. In ground floor ie within 4.00 mtr height ( From PL ) |
| 88 | With 1:6 Cement mortar, 20 mm. thick plaster.In First floor ieFrom 4.00 mtr height to 8.00mtr Height |
| 89 | With 1:6 Cement mortar, (b) 20 mm. thick plaster.a) In Second ieFrom 8.00 mtr height to 12.00mtr Height |
| 90 | With 1:4 Cement mortar10 mm. thick plaster.In ground floor ie within 4.00 mtr height ( From PL ) |
| 91 | With 1:4 Cement mortar10 mm. thick plaster.In First floor ieFrom 4.00 mtr height to 8.00mtr Height |
| 92 | With 1:4 Cement mortar(c) 10 mm. thick plaster.In Secont floor ie From 8.00 mtr height to 12.00mtr Height |
| 93 | With 1:6 Cement mortar, 15 mm. thick plaster.r.In ground floor ie within 4.00 mtr height ( From PL ) |
| 94 | With 1:6 Cement mortar, 15 mm. thick plaster.r. In First floor ieFrom 4.00 mtr height to 8.00mtr Height |
| 95 | With 1:6 Cement mortar, 15 mm. thick plaster.r.In Second floor ieFrom 8.00 mtr height to 12.00mtr Height |
| 96 | Extra for fluted, corrugated or ribbed plaster (over rate of corresponding rate of plaster). (Cement 0.135 Cu.m/100Sq.m) |
| 97 | Neat cement punning about 1.5 mm. thick in wall dado, window, sills, floor, drain etc. |
| 98 | Applying 2 coats of bonding agent with synthetic multi functional rubber emulsion having adhesive and water proofing properties by mixing with water in proportion (1 bonding agent : 4 water : 6 cement) as per Manufacturer's specification. |
| 99 | (Labour for Chipping of concrete surface before taking up Plastering work. |
| 100 | Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc.WallWith Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m.Area of each tile above 0.09 Sq.mColoured decorativeIn Ground Floor |
| 101 | WallWith Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m.(b) Area of each tile above 0.09 Sq.m(i) Coloured decorativeIn First Floor |
| 102 | Supplying and laying true to line and level Anti-Skid, Full Body, Homogeneous & Granular finish Vitrified Tiles conforming to IS:15622-2006 & IS 4457-2007 and testing shall be made in accordance with IS:13630 [Non- modular sizes for tiles with Skid resistance > 0.5, Mohr's hardness > 5.0, Staining resistance: Class-1, Water Absorption: E < 0.5%], MOR > 35 N/sq.mm in Internal area of building e.g. Toilet Block, Passage, Corridor, Accessible Open Terrace etc. set in 20 mm sand cement mortar (1:4) and 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg./Sqm or using Polymerised Adhesive (6 mm thick layer applied directly over finished artificial stone floor/ Mosaic etc without any backing course) laid after application slurry using 1.75 Kg of cement per Sqm below mortar only, joints grouted with admixture of white cement and colouring pigment to match with colour of tiles/ epoxy grout materials of approved make as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials, labour and all other incidental charges complete true to the manufacturer's specification and direction of Engineer-in-Charge. (White cement, synthetic adhesive and grout material to be supplied by the contractor).In Ground Floor: Sizes-600 mm x600mm x10 mm with breaking strength > 1500 N |
| 103 | In First Floor: Sizes-600 mm x600mm x10 mm with breaking strength > 1500 N |
| 104 | Supplying and laying true to line and level Double Charge Vitrified Tiles of approved brandconforming to IS 15622: 2006 (Group B I a) and tested as per IS 13630:2006 (relevant parts) [Non-modular sizes for tiles with Water Absorption (av.) ≤ 0.08 %] in floor, skirting etc. set in 20 mm thick sand cement mortar (1:4) bed prepared after application of slurry using 1.75Kg of cement per Sqm over the base and 2mm thick cement slurry using cement @2.91Kg./sqm at the back side of the tiles and laid over the mortar bed using 0.2 kg/sqm of White cement used for joint filling with approved pigment as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials,Iabour and all other incidental charges complete true to the manufacturer's specification and direction of Engineer-in-Charge. (Note: This work should not be executed without specific permission of Superintending Engineer) ln Ground FIoor:(size not Iess than 800mmX 800 mm X 10.2 mm thick) |
| 105 | ln First FIoor:(size not Iess than 800mmX 800 mm X 10.2 mm thick) |
| 106 | Supplying, fitting & fixing granite slabs 15mm to 18 mm. thick with uniform texture & without decorative veins in columns, wall, facia,rise etc. with 15 mm thick [avg] cement mortar (1:2) including making suitable arrangements to hold the stones properly by brass / copper hooks including pointing in cement mortar (1:2) (1 white cement : 2 marble dust) with admixture of pigment matching the stone shades all complete as per direction of the Engineer-in-charge including cost of all materials, labours, scaffolding, staging, curing and roughening of concrete surface complete.[Using cement slurry at back side of granite @ 4.4 kg/sq.m & white cement slurry for joint filling @ 1.8 kg/sq.m]In ground floorArea of each Granite slab 0.6 to 1.0 Square meter. |
| 107 | Supplying, fitting & fixing granite slabs 15mm to 18 mm. thick with uniform texture & without decorative veins in columns, wall, facia,rise etc. with 15 mm thick [avg] cement mortar (1:2) including making suitable arrangements to hold the stones properly by brass / copper hooks including pointing in cement mortar (1:2) (1 white cement : 2 marble dust) with admixture of pigment matching the stone shades all complete as per direction of the Engineer-in-charge including cost of all materials, labours, scaffolding, staging, curing and roughening of concrete surface complete.[Using cement slurry at back side of granite @ 4.4 kg/sq.m & white cement slurry for joint filling @ 1.8 kg/sq.m]In First floorArea of each Granite slab 0.6 to 1.0 Square meter. |
| 108 | Supplying,fitting & fixing granite slab 15mm to 18mm thick in floor, lobby, stair, landing and treads etc. over 20mm (avg) thick base of cement morter (1:2) laid with white cement slurry @ 4.40Kg per Square meter before placing of granite and jointed with white cement slurry @ 2.0 Kg per square meter with necessary pigments and complete as per direction of Engineer-in-charge including cost of all materials, labours, curing and roughening of concrete surface complete.In ground floorArea of each Granite slab 0.6 to 1.0 Square meter. |
| 109 | Supplying,fitting & fixing granite slab 15mm to 18mm thick in floor, lobby, stair, landing and treads etc. over 20mm (avg) thick base of cement morter (1:2) laid with white cement slurry @ 4.40Kg per Square meter before placing of granite and jointed with white cement slurry @ 2.0 Kg per square meter with necessary pigments and complete as per direction of Engineer-in-charge including cost of all materials, labours, curing and roughening of concrete surface complete.In First floorArea of each Granite slab 0.6 to 1.0 Square meter. |
| 110 | Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 111 | Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 112 | Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. On steel or other metal surface : With super gloss (hi-gloss) - Two coats (with any shade except white) |
| 113 | On timber or plastered surface : With super gloss (hi-gloss) -Two coats (with any shade except white) |
| 114 | Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. (In Ground Floor) One CoatSolvent based interior grade Acrylic Primer |
| 115 | Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC.In Ground Floor:Two Coats |
| 116 | In First Floor:Two Coats |
| 117 | In Second Floor:Two Coats |
| 118 | Applying Acrylic Emulsion Paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty (to be done under specific instruction of Superintending Engineer) :(Two coats) Luxury Quality |
| 119 | Rendering the Surface of walls and ceiling with White Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick). In Ground Floor |
| 120 | In First Floor: |
| 121 | In Second Floor: |
| 122 | Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer's specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. In Ground floor (Two Coat)Premium 100% Acrylic Emulsion |
| 123 | In First Floor: (Two Coat)Premium 100% Acrylic Emulsion |
| 124 | In Second Floor: (Two Coat)Premium 100% Acrylic Emulsion |
| 125 | Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. cutting trenches in any soil through masonry concrete structures etc if necessary and mending good damages including joining with jointing materails (Spun Yarn, Valamoid/Bitumen/M-Seal etc) complete.UPVC Pipes: 110 mm. Dia |
| 126 | UPVC Fittings:Bend 87.5 degree 110 mm. Dia |
| 127 | UPVC Fittings:Plain Tee 110 mm. Dia |
| 128 | French polishing to wood work including preparing surface (ordinary gloss)On new wood work |
| 129 | Artificial stone in floor, dado, staircase etc. with cement concrete (1:2:4) with stone chips, laid in panels as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (1:2) including smooth finishing and rounding off corners including raking out joints or roughening of concrete surface and application of cement slurry before flooring works, using cement @ 1.75 kg./sq.m. all complete including all materials and labour.In ground floor.Using grey cement25 mm. thick |
| 130 | Supplying& laying 20 mm designer chequered tiles of any shade and of approved quality as per IS: 1237: 1980 laid in patterns as directed in pavement, footpath including necessary underlay 25 mm thick average cement mortar (1:3) complete in all respect with all labour and materials [using cement slurry @ 4.4 kg/Sq.m at back side of tiles. Cement of mortar & slurry will be supplied by the Department. Border concrete if necessary to be paid separately].Red variety |
| 131 | Supplying, fitting and fixing Stainless Steel railing consist of 38mm dia and 900mm height vertical balustrade at every two alternative steps, 50mm dia top rail, 3 (three) nos 19mm dia horizontal Strainless steel pipe and base/cover plate with Strainless Steel GRADE 304 containing 7.5% nickle (Interior Grade) Brushed/Mat finish, complete as per direction of the Engineer-in-charge. Weight of Strainless Steel railing per metre 6.5 Kg (approx) |
| 132 | S & P WorksConstructing Inspection pit of inside measurement 600mm X 600mm X upto 600mm (depth) with 250 mm thick 1st. class brick work in cement mortar (1:4) on all sides, bottom of the pit consisting of 100 mm thick cement concrete (1:3:6) with stone chips over a layer of jhama brick flat soling, 15 mm thick (1:4) cement plaster to inside walls and out-side walls upto G.L. and 20 mm.thick (1:4) plaster to bottom of the pit, providing necessary invert with cement concrete (1:3:6) with stone chips as per direction, neat cement finishing to entire internal surfaces, top of the pit covered with 100 mm thick R.C.C. slab (1:1.5:3) with stone chips and necessary reinforcements upto 1% and shuttering including 6 mm thick cement plaster (1:4) in all external surfaces of the slab and one 560 mm dia. R.C.C. manhole cover of approved make supplied, fitted and fixed in the slab with necessary fittings, necessary earthwork in excavation in all sorts of soil, filling sides of the pit with earth and removing spoils after work complete in all respect with all costs of labour and materials.With Pakur variety Stone Chips & (SAIL/TATA/RINL Steel) |
| 133 | Construction of circular soak well 2.5 metre deep in all types of sandy soils with dry brick work upto 1.6 metre from the bottom having 150 mm intermediate cement brick work (1:4) band all round and cement brick work (1:4) upto 0.90 metre from top with 20mm thick cement plastering (1:4) to inside face upto the depth of cement brick work, 15mm thick cement plaster (1:4) on outer face from top of the well upto G.L. and 6 mm thick cement plaster (1:4) on top of the R.C.C. cover slab including filling bottom 1.00 metre of inside of the well with brick metal (50 mm to 63 mm size) including R.C.C. cover slab of 100 mm thick with cement conc (1:1.5:3) with stone chips with necessary reinforcement and shuttering including one 560 mm dia. R.C.C. manhole cover (heavy type)of approved make supplied, fitted and fixed in the cover slab with necessary fittings, making nacessary arrangements for pipe connections, excavation of well including shoring, dewatering and removing the exess earth from the premises as per direction complete in all respect with all costs of labour and materials.With 250 mm thick dry brick work and 250 mm thick cement brick work (1:6) and 1.00m inside dia. With Pakur variet Stone Chips & (SAIL/TATA/RINL Steel) |
| 134 | Construction of septic tank of different capacities as per approved drawing with 1st class brick work in cement mortar (1:4) including two 560 mm dia. R.C.C. manhole cover (heavy type) of approved make supplied, fitted and fixed in the 100mm thick R.C.C (1:1.5:3) top slab with necessary fittings, 20mm thick cement plaster (4 : 1) with neat cement finish to the internal surfaces and 15 mm thick cement plaster (4 : 1) to outside wall upto 200 mm below G.L floor finished with 25 mm thick grey artificial stone over 100 mm thick R.C.C (1:1.5:3) bottom slab including supplying, fitting and fixing all necessary specials, fittings, S.W. tees, C.I. foot rest etc. including excavation earth in all sorts of soil, shoring, bailing out and pumping out water as necessary, ramming, dressing the bed and refilling the sides of the tanks with earth, removing spoils, filling up the chamber with clear water, removing foreign materials from the chamber and including constructing attached inspection pit as per approved drawing and connecting all necessary pipes, joints etc. with internal plaster work and artificial stone flooring is to be done with admixture of water proofing compound @ 0.5% by weight of cement with all costs of labour and materials. Note:- (i) Finished level of Septic Tank should be 400 mm. from Ground Level. (ii) Height of 50 mm. Ventilation pipe &Mosquito proof mesh, should be follwed as per IS:2470,Part- I.Payment will be made separetly on the basis of actual height based on relevant I.S.Code.For 20 usersWith Pakur variet Stone Chips & (SAIL/TATA/RINL Steel) |
| 135 | For 50 usersi) With Pakur variet Stone Chips & (SAIL/TATA/RINL Steel) |
| 136 | Supplying P.V.C. water storage tank of approved quality with closed top with lid (Black) - Multilayer 2000 litre capacity |
| 137 | Labour for hoisting plastic water storage tank.Above 1500 litre upto 5000 litre capacityUpto Second story from G.L. |
| 138 | Labour for punching hole in plastic water storage tank upto 50 mm dia |
| 139 | Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992 Single Socketed 3 Meter Length 110 mm |
| 140 | Fittings Plain Tee 110 mm |
| 141 | Door Tee 110 mm |
| 142 | Door Bend (LH) & (RH)110 mm |
| 143 | Vent Cowl 110 mm |
| 144 | Pipe Clip 110 mm |
| 145 | 125/110 P Trap with W.C. Ring 75 mm |
| 146 | Labour for fitting and fixing U.P.V.C. pipes for above ground work including cost of jointing materials etc. fitting and fixing all necessary specials, cutting pipes, cutting holes in walls or R.C. floor where necessary and mending good all damages excluding the cost of masonry or concrete work, if necessary, but including the cost and fitting and fixing holder bat clamps (any floor) or for underground work including cutting trenches upto 1.5 metre and refilling the same complete as per direction of the Engineerin- charge. (Payment will be made on centre line measurement of the total pipeline including specials.Above ground110 mm dia. |
| 147 | Supplying, fitting and fixing bib cock or stop cock. Chromium plated Bib Cock with wall flange (Equivalent to Code No. 5047 & Model - Florentine of Jaquar or similar brand). |
| 148 | Chromium plated angular Stop Cock with wall flange (Equivalent to Code No. 5053 & Model - Florentine of Jaquar or similar brand). |
| 149 | Supplying, fitting and fixing pillar cock of approved make.CP 2-way bib Cock - 15 mm, supplied, fitted and fixed. (Code No.5041 & Model - FLORENTINE of JAQUAR or similar brand). |
| 150 | Supplying, fitting and fixing gunmetal wheel valve of approved brand and make tested to 21 kg per sq. cm. (for water lines only). 40 mm dia |
| 151 | 32 mm dia |
| 152 | 25 mm dia |
| 153 | Supplying, fitting and fixing CPVC (Chlorinated Polyvinyl Chloride) pipes of approved make conforming to IS-15778: 2007 . with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials.For Exposed WorkCPVC Pipes Class-1, SDR-11(Dia) 25 mm |
| 154 | For Exposed WorkCPVC Pipes Class-1 , SDR-11(Dia) 32 mm |
| 155 | For Exposed WorkCPVC Pipes Class-1 , SDR-11(Dia) 40 mm |
| 156 | For Concealed WorkCPVC Pipes Class-120 mm |
| 157 | Supplying, fitting & fixing Aluminium domical grating.100 mm |
| 158 | Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of approved make in position complete excluding 'P' or 'S' trap (excluding cost of concrete for fixing).530 mm X 410 mm |
| 159 | Supplying, fitting and fixing Anglo-Indian W.C. in white glazed vitreous china ware of approved make complete in position with necessary bolts, nuts etc. With 'P' trap (with vent) |
| 160 | Supplying, fitting and fixing Closet seat of approved make with lid and C.P. hinges, rubber buffer and brass screws complete.Anglo IndianPlastic (hallow type) white |
| 161 | Supplying, fitting and fixing shower of approved brand and make.Chromium plated round shower with revolving joint 100 mm dia with rubid cleaning system (Equivalent to Code No. 542(N) & Model - Tropical / Sumthing Special of ESSCO or similar brand). |
| 162 | Hand Shower(Health Faucet) with 1mtr Fexible Tube with Wall Hook (Equivalent to Code No.573 & Model -ALLIED of Jaquar or similar). |
| 163 | Supplying, fitting and fixing towel rail with two brackets. C.P. over brass25 mm dia. and 600 mm long |
| 164 | Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specification with P.V.C. fittings complete,C.I. brackets including two coats of painting to bracket etc. |
| 165 | Supplying,fitting and fixing 32 mm dia. Flush Pipe of approved make with necessary fixing materials and clamps complete.Polythene Flush Pipe |
| 166 | Supplying, fitting and fixing white vitreous china best quality approved make wash basin with C.I. brackets on 75 mm X 75 mm wooden blocks, C.P. waste fittings of 32 mm dia., one approved quality brass C.P. pillar cock of 15 mm dia., C.P. chain with rubber plug of 30 mm dia., approved quality P.V.C. waste pipe with C.P. nut 32 mm dia., 900 mm long approved quality P.V.C. connection pipe with heavy brass C.P. nut including mending good all damages and painting the brackets with two coats of approved paint.550 mm X 400 mm size |
| 167 | Supplying, fitting and fixing pedestal of approved make for wash basin (white) |
| 168 | Supplying, fitting & Fixing EWC (Size- 710x370x810 mm)in white glazed vitreous chinaware of approved make supplying, fitting and fixing in position complete with necessary nut and bolts. (Model Code No. S10221114-P Trap (CRUSE SET) of CERA or equivalent.) |
| 169 | Supplying, fitting and fixing 10 litre white glazed vitreous chinaware of approve low-down cistern of approved make with either side or bottom inlet, side overflow, brackets complete with all internal fittings. (Model Code No. S1060106 of CERA or equivalent.)White |
| 170 | Soft Close seat cover of approved make with lid and C.P. hinges, rubber buffer and brass screws suppling, fitting and fixing complete. E W C (Model Code No. B1520118 of CERA or equivalent.)White |
| 171 | Supplying, fitting and fixing Stainless steel Wall Mounted Grab Bar. Load bearing capacity 150 kg, covered by Nylon surface with contour finish (for better grip) with Anti-bacterial surface complete. (Model Code No. B2210106 of CERA or equivalent.)600mm Long |
| 172 | Supplying, fitting and fixing Stainless steel Wall Mounted Hinged hand rail (750X100 mm) covered by Nylon surface with contour finish (for better grip) with two brackets.(Model Code No.B2210108 of CERA or equivalent.)750 mm long |
| 173 | Supplying, fitting and fixing 15 mm Twin Flush Fitting (Model Code No. B1810112 of CERA or equivalent). |
| 174 | Supplying, fitting and fixing bevelled edged mirror 5.5 mm thick silver red as per I.S. 3438 / 1965 together with brass C.P. hinges. 450 mm X 300 mm |
| 175 | Supplying,fitting and fixing approved brand 32 mm dia.P.V.C. waste pipe, with PVC coupling at one end fitted with necessary clamps. 900 mm long |
| 176 | Supplying,fitting and fixing approved brand P.V.C. CONNECTOR white flexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia.750 mm long |
| 177 | Supplying, fitting and fixing Flat back urinal (half stall urinal) in white vitreous chinaware of approved make in position with brass screws on 75mm X 75 mm X 75 mm wooden blocks complete.635 mm X 395 mm X 420 mm |
| 178 | Supplying, fitting and fixing Squating plate with integral flushing in white vitreous chinaware of approved make in cement concrete (6:3:1) with jhama chips complete. (Payment of concrete will be paid seperately) 450 mm X 350 mm |
| 179 | Supplying, fitting and fixing liquid soap container.Cromium plated(Prayag or equivalent) |
| 180 | Supplying, fitting and fixing glass shelf with aluminium guard rails. Ordinary type with 5.5 mm sheet glass. 450 mm X 125 mm |
| 181 | Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately)For Exposed WorkPVC Pipes(Dia) 40 mm |
| 182 | PART-B : 200 X 100 mm dia. DEEP TUBE WELL : Supplying, fitting and fixing G.I. cap at top200 mm |
| 183 | Supplying, fitting and fixing heavy type bell mouth reducing socket.100 mm X 200 mm |
| 184 | Supplying, fitting and fixing 300 mm M.S. housing clamp of approved quality. For 200 mm dia. housing pipe. |
| 185 | Providing 200 mm centre guide. With Clamp |
| 186 | Labour for making arrangement for showing verticality test including the cost for hire charge tools and plants, scaffolding, lobour etc all complete. |
| 187 | Collecting sample of water for bacteriological and chemical test from any depth at any time during execution of work including hire and labour charges for tools and plants and sterilising the equipments, paying all charges and fees, testing etc. complete in all respect as per direction |
| 188 | Packing the annular space between the outside of the tubewell pipes and strainers and the bore with pea size washed gravel of approved quality having size from 2mm. to 5mm. or the size approved by the E.I.C. including cost of all materials labour and equipment complete. NOTE :- Initial 6 Mtr. of annular space between the housing pipe and the bore should not be shrouded with pea size gravel to avoid contamination with surface water. |
| 189 | Packing annular space between the outside of the housing pipe and the bore with puddle clay balls of approved size as per direction of the EIC with cost of materials,labour and equipment complete. |
| 190 | Geophysical investigation of the acquifer by electrologging system with all tools and plants as necessary including supply of necessary report. |
| 191 | Washing and developing tube well with air compressor pump and engine for 8 (eight) hours continuous pumping per day with necessary arrangements for testing the yield in gallons per hour with 'V' notch including hire and labour charges for all tools and plants and scaffolding as required. |
| 192 | Supply of PVC pipes & fittings Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). PVC Pipes 100 mm |
| 193 | 200 mm |
| 194 | Supplying high density polythene strainer of approved make with adapter conforming to I.S. specifications. 100 mm dia. |
| 195 | Supplying, fitting and fixing PVC pipes for underground work of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted including cost of all materials ,jointing materials, cutting pipes, making threads ,cutting trenches upto 1.5 metre below surface in all sorts of soil and refilling the same as directed complete in all respect. (Payment will be made on the centre line measurement of the total pipe line including all specials No separate payment will be made for accessories,specials.)PVC Pipes(Dia)25 mm |
| 196 | Supplying, fitting and fixing Peet's valve fullway gunmetal standard pattern best quality of approved brand bearing I.S.I. marking with fittings (tested to 21 kg per sq. cm.)..(Make HM/Laxmi)40 mm dia |
| 197 | Supplying,fitting and fixing check valve (horizontal) G.M. tested to 21 kg per sq. cm. 32 mm dia |
| 198 | Drilling Bore Hole Drilling Bore Hole by a suitable DTH cum mud rotary combination rig with foam and mud drilling including collection of Litho- Logical surplus with maintaining the time log for drilling through different points as directed by E.I.CDrilling 250mm dia. borehole suitable for lowering 200mm internal dia. casing pipe lowering through over burden of clay / consolidated moorum / consolidated laterite fragmented granite formation including lowering the casing pipe through over burden up to a depth of 50 mtr. Below ground level. First 50 metre |
| 199 | Drilling 165mm dia through fusser consolidated hard rock strata with necessary valve for hammer and use necessary air pressure from 50 m to 250m.. From First 50 metre to Rest 250m |
| 200 | Mobilization of machinery and equipment required for drilling lowering etc. complete.as per direction of EIC |
| 201 | Pump Installation ; Supply & lowering of 3 HP, 3 phase 415V submersible pump motor set of 2900 RPM outlet 40mm dia having provision of coupling pump with motor capable to discharge 8500 LPH clear sand free water at a total head of 90 mtr (Make-KSB model- 7C/15) |
| 202 | Suppling & Fitting 40 mm adoptor for motor & pump hanging with column pipe. |
| 203 | Supply & Lowering of 6mm water proof PVC coated steel rope hanging pump through boring. |
| 204 | Supply & Lowering of 40mm PVC pipe (Column pipe) with both side threaded with necessary Jointing etc complete 3 mtr length Make Oriplast. |
| 205 | Suppling & Fitting 40mm MS Half round type holding clamp to holding the column pipe incl. S &F nut bolt & washer as per direction of E-In- C. |
| 206 | Suppling & Fitting suitable size round type well cover with hole for column pipe as per direction of E-In-C |
| 207 | Supply & Laying 3 core 2.5 sqmm flat Cable (Finolex/PWD approved) for submersible pump-motor set |
| 208 | Suppling & Fitting 1.1 kv Gr 4C 16 sq mm XLPE/PVC AI /A cable in underground trench (as per PWD/GS). |
| 209 | Suppling & Fitting 415V FN 32A TPN rewireble type procelain main in sheet steel encolser Switch fuse Unit on angle iron frame |
| 210 | Supplying & fixing 3Phase starter for 3HP submersible pump moter on iron frame on wall as per G-5 (L&T) [Model-mk] |
| 211 | Supply & erection of 1200 mmx 450 mm x 400 mm out door type shut steel piller Box of 3.5 ( 10 SWG ) thick CRCA sheet T he pillar box comprising of the following :- S&F 415 v 32A TPN rewiable type porcelain switch fuse unit as incoming 1 no.b) 63A 415 volt 4 bar copper BBC in 16 SWG M,S sheet enclosure of lenth 400mm as out going 1 no.c) S&F DOL 3ph starter for 3 HP submer sible pump motor- 1no.d ) 250 v 15 A Bakelite fuse unit & R-Y-B indicator with toggle switch 1 no Inter connectiion between switches includining supply &fixing Digital volt meter (0-500V)and Digital Ammter( 0-50A ) selector switch 2 nos indicating lamp (LED type) . The piller Box should have double leaf single door with railway type locking arrangement including pad locking system . The piller box should have brass nine net guard for ventilation .The complete set should be painted with one coat of Red lead primer a two coats of synthetic enamel paint of approved make the piller box to be errected on 550 mmx 500 mm foundation . The 10'' brick foundation with neat cement finishing is of height 2.5 ft with hollow central portion for cable entry incl . filling upo;f hollow portion with dry sand after connection of cable s. The pillar box should have two nos. lifting lugs at two sides. |
| 212 | PART-C : Fire Fighting C02 type Fire extingusher (4.5 Kg) with fixing arrangements. |
| 213 | ABC type Fire extingusher (2.0 Kg) with fixing arrangements. |
| 214 | ABC type Fire extingusher (6.0 Kg) with fixing arrangements. |
| 215 | Water C02 9 litres cartridge type Fire extingusher with fixing arrangements. |
| 216 | C02 type Fire extingusher (22.5 Kg) with fixing arrangements. |
| 217 | Fire bucket (9 litres) (two nos set) with fixing arrangements. |
| 218 | DCP type Fire extingusher (25 Kg) with fixing arrangements and trolley. |
| 219 | \\"EXIT\\", \\"STAIRCASE\\", & \\"FIRE EXTINGUSHER\\" signages made of flourscent sheet pasted on Acrylic board of 12\\" x 6\\" size to be mounted on each floor. |
| 220 | Add GST @ 18% on Rs 19065770.00 over Item No. 1 to 219 |
| 221 | Add Labour Welfare Cess @ 1% on Rs.22497609.00 over Item No. 1 to 206 Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 03, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 29, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 20 daysJul 31, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 22 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender