Tender For Addition Alteration To Security Wall And Sentry Post And Allied Works At Nagrota
Tender Value
9.70 Crore
Estimated cost
Bid Submission
07 Aug 2026
26 days left
EMD
8.10 Lakhs
Bank guarantee accepted
Document Fee
3000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jammu → Jammu and Kashmir
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Addition Alteration To Security Wall And Sentry Post And Allied Works At Nagrota
BOQ
| Sl. No. | Item Description |
| 1 | Sch 'A' Part-I (Building Work):-This Schedule is not Pre-Priced by MES and the Pre-Priced rate indicated as \\"Rs. 0.00\\" under col.5 signifies this fact only. |
| 2 | Construction of Guard Room for 02 x Hav and 06 x ORs with Verandah and sentry post at first floor complete all as specified and shown on drawings. |
| 3 | Total Amount of Sch 'A' Part - II (Internal Electric Supply) |
| 4 | Total Amount of Sch 'A' Part - III (Internal Water Supply) |
| 5 | Total Amount of Sch 'A' Part - IV (Plumbing Work) |
| 6 | Total Amount of Sch 'A' Part - V (Road Path Culvert and Interlocking Paver Block) |
| 7 | Total Amount of Sch 'A' Part -VI (External Water Supply) |
| 8 | Total Amount of Sch 'A' Part -VII (External Electric Supply) |
| 9 | Total Amount of Sch 'A' Part -VIII (Sewage Disposal) |
| 10 | Total Amount of Sch 'A' Part -IX (Area Drainage) |
| 11 | Total Amount of Sch 'A' Part -X (Security Wall) |
| 12 | Total Amount of Sch 'A' Part -XI (Anti Cut Weld Mesh Fencing) |
| 13 | Total Amount of Sch 'A' Part-XII (Protective Work) |
| 14 | Total Amount of Sch 'A' Part-XIII (Demolition) |
| 15 | Sch 'A' Part -XIV (Misc Items of Work) Note : This Schedule is not Pre-Priced by MES and the Pre-Priced rate indicated as \\"Rs. 0.00\\" under col.5 signifies this fact only. |
| 16 | Modular blanking plates 1 module complete all as specified and directed. |
| 17 | Building security light luminaries energy saving and environment friendly long life LED light of 25W made up of pressure die cast aluminium housing with acrylic cover as diffuser with IP66 protection and Impact resistance of IK07, including GI pipe bracket 32 mm bore, light grade dia, 1.2 m long bend in shape fixed on wall having an angle 120 degree, fixed with and suitable size nuts, bolts and washers etc complete all as specified and directed. |
| 18 | Wall mounting fan swing type 400 mm sweep single phase AC 230/240V complete for wall mounting incl grouting, holding down bolts, nuts, and provision of flexible copper conductor cable 3 core 23/0.0076 size from ceiling rose to fan complete all as specified and directed. |
| 19 | Exhaust fan, steel body heavy duty AC single phase 230V of size 300mm sweep with blades, frame and louvers fixed as directed. |
| 20 | Precast box culvert of size 2000 mm (height) x 2000 mm (width) (from inner side of box culvert) and 2500 mm (height) x 2500 mm (width) (from outer side of box culvert ) and haunch of size 200 mm x 200 mm , made with Fe-500/550d grade TMT steel reinforcement bars in each unit made of high performance self compacting concrete (SSC) of M-40 grade, cured under controlled factory conditions having loading capacity of class 70R as per IRC-006 (100 tonne load wheel vehicle).all manufacturing process must comply with Indain Standards. the curing process must be maintained using RO water and chiller plants for quality assurance. The formwork used for casting should be made automobile grade water tight steel enabling the production of highly accurate and consistent components. concrete mix design of IS: 9103, complete all as specified and directed. |
| 21 | Brick masonary valve pit chamber of size 0.45m x 0.45m x 0.45m (internal dimension) (above GL 0.30 mtr) suitable for fixing of gate valves, 15cm thick foundation using PCC 1:4:8 type D-2 over 15cm thick hardcore of broken stone, 23cm thick brick walls built in cement and sand mortar 1:4, 15mm thick internal and externally flush pointing in the same mortar as the work proceeds top of floor in cement and sand mortar 1:3, 15mm thick, finished even and smooth, without using extra cement, 6 mm thick plate cover on 40mm x 40mm x 6mm MS angle frame embeded in PCC 1:2:4 type B-1 coping 40mm thick in PCC 1:2:4 type B-0, having rectangular, hinged, opening of size 40 x 40mm with locking arrangements ,hold fasts, etc, applying one coat of red oxide primer and two coats of synthetic enamel paint to all steel surfaces and earth work in any type of soil including disposal of debris outside MD land complete all as specified and directed. |
| 22 | Double walled corrugated (DWC) pipe for cable protection with outer dia 40mm and inner dia 30mm including suitable size of coupler for connection of pipe complete all as specified and directed. |
| 23 | Feeder pillar box out door type ‘Factory Made’ made out from 3.15 mm thick MS sheet supported with legs of 45cm long made of iron angle 25 mm x 25 mm x 4 mm thick of size 75 cm x 60 cm x 45 cm with 04 Nos aluminium bus bar of 100 Amps mounted on porcelain insulator duly drilled hole for cable connection including front and rear side opening with locking arrangement provn for incoming and outgoing cables with glands including painting with two coat of smoke grey synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.Note:- Feeder pillar box shall be mounted on brickwork in CM 1:4 not less than 30 cm above ground level with suitable foundation as directed , rendering 15 mm in CM 1:6 and two coats of cement base paint and the rates quoted are inclusive of the same. |
| 24 | Junction box made of SMC/FRP sheet ready made of size 400 mm x 300 mm x 190 mm having 10 A Capacity RYB and neutral aluminium bus bar of 3 mm thick duly fitted on suitable insulator, and MCB SP 6 A 10 KA 'C' series, 240V -01 No. with fixing arrangement fixed properly to pole/fixed on wall with MS Clamps 25x5 mm and nut and bolts complete all as specified and directed. |
| 25 | Mounting arm for installation of LED light made from 40 mm dia GI pipe light grade (B class) of total length 2 mtr (to be fabricated as per approval design) to be supplied alongwith mounting clamps-02 Nos fabricated from 65 mm x 5 mm MS providing 04 Nos nut bolt washers etc complete all as specified and directed. |
| 26 | Stranded PVC insulated and sheathed stranded copper conductor cable of size 1.5 Sqmm 3core complete all as specified and directed |
| 27 | LLDPE septic tank designed to carry sewage and sludge water, comprising, excavation in any type of soil, returning filling, disposal of surplus spoils to a distance not exc 50 mtr from starting point in any type of soil, PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregates) in foundation, 200mm thick, vent shaft, connetions etc., for 20 users with upflow filter including media and all fittings, fixtures, testing on completion, complete all as specified and directed. |
| 28 | Soakage well 1.80 mtr dia and 3m deep including excavation in any type of soil, PCC 1:3:6, type C-2 brick masonary with honey combed in CM 1:4 with top ring M-25 (Design Mix) including intercepting chamber and screen chamber made of brick masonary in cement mortar (1:4), RCC cover slab of RCC M-25 (Design Mix), intercepting pipe of RCC/DWC complete filled with bricks bats, complete all as specified and directed. |
| 29 | Precast footing of size (base + Pedestal) 160cm x 190cm x 150cm have base of 160cm x 190cm x 30cm with pedestal dimensions of 30cm x 65cm (at bottom) and 30cm x 45cm (at top), footing to be made of high performance self compacting concrete (SSC) of M-40 grade placed on 15 cm thick PCC after proper compacting of soil 6 No 12 mm dia and 300 mm long bars for fixing 100 mm I-Section at the top of footing, footing made with Fe-500/550D grade TMT steel reinforcement bars, cured under controlled factory conditions through steam curing all. Manufacturing process must comply with BIS, JIS or ISO 9001 Standards, the curing process must be maintained using RO water and chillar plants for quality assurance, the formwork used for casting should be made of automobile production of highway accurate and consistent components. Concerete Design Mis of IS:9103 complete all as specified and directed. |
| 30 | Rectangular anti climbing high security electrical resistance galvanised wire weld mesh panels (size 955mm x 2667mm +/- 5mm tolerance, each weighing 23.25 Kg, +/- 5% tolerance), powder coated, installed with necessary clamps, profile plates complete all as shown on drgs, specified and directed. Mesh wire diameter & tolerance: Core diameter of the horizontal wire: 4mm±0.05mm (Conforming to IS 280-2006 Core diameter of the vertical wire 4mm ±0.05mm. Tensile strength of wire: 550 N/Sqmm.Mesh size: Distance between horizontal wire 12.7mm. Distance between vertical wire 76.2 mm.(subject to tolerance in accordance with EN 10223-7, EN 10245-1)Welding strength : The average weld shear strength of 4 welds taken at random shall not be less than 50% of breaking strength of vertical wire (EN-10223-7). Zinc coating: 40-50 GSM (100% zinc) (conforming to IS 4826-1979). Powder coating: After welding the paneis shall be polyester powder coated in single layer of thickness 60-80 micron in green colour RAL 6005 and shall withstand 1000 hours of salt spray test. Reference drawing: WM-WC-0417-S-377 dt 01.04.2017.Wire tensile strength: Min 550N/Sqmm Weld Strength: The average weld shear strength of 4 welds taken at random shall not be less than 50% of the breaking strength of the vertical wire Powder Coating EN 13438-2005/IS13871-1993.(Note: Supply of omega clamps with profile cover plate will be measured separately).Manufacturer/Fabricater: M/S A-1 Fance Products Company Pvt Ltd Mumbai or equivalent as approved by the GE |
| 31 | Circular hollow MS steel Tube (IS-1161), 76 mm Dia, 3.2 mm thickness (+/-10% tolerance), 3345mm long (+/-5%) (2745 mm above ground level + 600 mm under the ground level), each weighing 20Kgs (+/-5% tolerance) hot dipped galvanized to minimum 350 GSM as per IS 2629/1S 4759/ASTMA 123 as in fence posts. Complete all as shown in drgs, specified and as directed by Engr-in-Charge. Manufacturer/ Fabricater: M/S A-1 Fence Products Company Pvt Ltd Mumbai or equivalent as approved by the GE |
| 32 | Supply only Omega clamps with profile cover plate to tighten the mesh panel along the posts with diameter 76mm, 35 mm width and 3mm thick flat-35mm width, 3mm thick (MS strip as per IS 1730) hot dipped galvanized to minimum 350 GSM as per IS 2629/1S 4759/ASTMA 123 (7 Nos per post). Each clamp will be supplied with a pair of SS 304 mushroom headed, square necked bolts and security nuts M8x50 (IS 8535-1987) each set of Omega clamps including weight of SS-304 security Nuts, shall be weighing 0.66Kg (+/- 5% tolerance), complete all as specified and as directed. Manufacturer/Fabricater: M/S A-1 Fence Products Company Pvt Ltd Mumbai or equivalent as approved by the GE. |
| 33 | STRAINING Y- ARM: Straining Y- Arm shall be of MS Angle iron of size 40 mm x 25 mm x 3 mm (IS-1730), 750mm length, each one of hot dipped galvanized to 350 GSM as per IS 2629/IS 4759/ASTM A 123, eanh Y-Arm weighing 6.75 Kg (+/-5% tolerance), with 63mm outer dia of sleeve cap, bolted as in straining Y-arm on the top of the fence post at every 30 mtr distance fitted with stainless steel mushroom head bolt with breakable head safety nut (M8 x 120) (2 No per post) each set of SS-304 security Nuts, weighing 0.168Kg (+/-5% tolerance), complete all as specified and as directed. Manufacturer/Fabricater: M/S A-1 Fence Products Company Pvt Ltd Mumbai or equivalent as approved by the GE |
| 34 | 10mm dia 250mm long GI anchor rod, each weighing 0.155Kg (+/- 5% tolerance) to tie with fence post at bottom using the wire (2 Nos For each post) complete all as shown on drawings, specified and as directed. Manufacturer/Fabricater: M/S A-1 Fence Products Company Pvt Ltd Mumbai or equivalent as approved |
| 35 | High tensile heavy galvanized mild steel wire for line wire & high tensile barb wire made of high carbon steel approximately 0.28%, line wire diameter shall be 3.15mm with 2mm dia barbs at 100mm spacing conforming to (IS 4826-1979) zinc coating 290 GSM, tensile strength 1450-1650N/Sqmm, barb wire diameter 2mm zinc coating 240 GSM, tensile strength 450-600 N/Sqmm, barbing pitch: 100mm, barb type: 4 point IOWA style, per 100mtr weighing 9.80Kg (+/-5% tolerance) Strands Single (6 row), straining and fixing to Y-arms straining bolts, including and tying at crossings with and provision of galvanised mild sty wire, staples steel pieces etc., complete all as shown on drgs, as specified and as Charge (each line wire to be measured separately) Manufacturer Fabricater: M/S Company Pvt Ltd Mumbai or equivalent as approved by the GE |
| 36 | Punched type concertina coil as per latest 18 6745-1972 with galvanised coating and punched type material as per IS deep drawn quality with galvanised coating having medium barbs fixed in position and secured to fence posts/straining Y- arm stretched to a length so as to achieve 1050 mm dia as in fencing including fixing with special galvanised fastners such as J clips, C clips, U clips fixed at any height of security fence including necessary scaffolding complete all as shown in drgs, specified and directed by the Engr-in-Charge.Size of Coil : 1050mm dia/56 loops/2.5mm core wire.Type of strip: Heavy galvanised conforming to IS 1730 (1989)Type of core wire: Heavy galvanised conforming to IS 280-2006 Zinc coating to strip 200GSM/SommZinc coating to line wire: 275 GSM/Sqmm (IS 6745-1972 Reprint 2006) Tensile strength of wire 1400-1500 N/Sqmm.Weight: 14.63 Kg/coil (+/- 5% tolerance).Blade: 22mm Bart profile: Medium blade (MBBT)Distance between barb: 35mm Stretchable length of each coil: 12m Type of clip Hardened galvanised steel.Manufacturer/Fabricater: M/S A-1 Fence Products Company Pvt Ltd Mumbai or equivalent as approved by the GE. |
| 37 | Notes: (Applicable to Srl item No. 15.15 to 15.21 here-in-before) (a) The contractor shall within 15 days of the placing of work order, intimate to GE the name of manufacturer meeting specified criteria (documents such as copies of supply orders, Invoices of materials supplied, in support thereof shall be produced) for the materials in writing for his approval after due verification of the credentials of manufacturer for these products. The manufacturer as approved by GE shall be in possession of NSIC/MSME registration for manufacturing and supplying composite fencing system using Weld mesh panels, Fence Posts, Accessories and Razor wire coils as specified vide above mentioned items No.15.15 to 15.21 with in-house plant and machinery for manufacturing and polyester powder coating as well as thermo plastic coating as per specifications for coating. |
| 38 | (i) The Manufacturer Should be manufacturing and supplying composite fence system Weld mesh panels, Fence Posts, Accessories and Razor wire coils for a minimum three years period.(ii) The manufacturer shall provide Type Test certificate for Sample testing of 1000Hrs of Salt Spray Test from a renowned NABL approved Lab towards Powder Coating of materials manufactured by them. |
| 39 | (b) Irrespective of whatever specified towards testing of materials in the tender documents production of test certificates by the contractor from the manufacturer is mandatory towards materiais procured against Srl items 15.15 to 15.21 here-in-before. To ensure the materials brought to site for incorporation in the work conform to testing parameters specified in Appx 'A' to particular specifications, Frequency of independent random testing of the materials under serial item No 15.15 to 15.21 shall be as per relevant code of practice subject to a minimum of one sample from each lot of materials manufatured (incase the materials procured are from different lots manufatured) one sample per 1000mt length of fence (incase all the material is manufacutred in one lot). Independent testing shall be got carried out by the GE from one of the NABL Labs specified in Appx 'B' to Particular Specifications for materials against Sri items 15.15 to 15.21 here-in-before. The cost towards testing charges, transport and handling shall be bome by the contractor within the rates quoted against said items and nothing extra shall be admissible on this account. |
| 40 | (c) The contractor shall submit warranty for a period of 24 months from the date of certified completion against all the manufacturing defects for all the materials procured vide Srl items No. 15.15 to 15.21 here-in-before. |
| 41 | Crete core designer wall panel (alongwith column) having both side designed as per Engineer-in-Charge of size 5000 mm (length including column-350mm x 300 mm) x 1600 mm (height) x 100 mm (thickness of panel) made with Fe- 500/550d grade TMT steel reinforcement bars in each panel which is made of high performance self compacting concrete (SSC) of M-40 grade, cured under controlled factory conditions. All manufacturing process must comply with Indain Standards. The curing process must be maintained using ro water and chiller plants for quality assurance. The formwork used for casting should be made automobile grade water tight steel enabling the production of highly accurate and consistent components. concrete mix design of IS: 9103 complete all as specified and directed. |
| 42 | Concertina coil fencing with punched tape concertina coil 1050mm dia 10 metre openable length, having 50 Nos rounds per 6 metre length, spring core wire (2.5 mm thick) of high tensile strength of 165 Kg/Sqmm with tape (0.52mm thick) and weight 43.478 gm/ metre and fixing the same with existing Y-shape angle iron with 6 horizontal R.B.T (Reinforced Barbed Tape) wire, stud tied with G.I staple and GI clips to retain horizontal, including necessary bolts, all complete as per direction of Engineer-in-Charge. |
| 43 | Air cooler (Desert cooler), stainless steel body, with copper motor (1350 RPM), powerful fan (16 to 18 inch Metal Blades), 4-way air deflection, Tank cap 60 litres to 70 litres, antibacterial honeycomb pads, high air delivery (3500-4700 Cum/hr) complete all as specified and directed by Engineer-in-charge. |
| 44 | Water Cooler 40 LPH cooling capacity and 80 LPH Storage capacity made by stainless steel, rust-resistant with two push-button, heavy-duty cooling capacity complete. All as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 02, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedAug 07, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 26 daysAug 14, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 33 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender