Tender For Repair / Maintenance Of Joinery In Zone A Domestic Area At Af Stn Jaisalmer
Tender Value
40 Lakhs
Estimated cost
Bid Submission
23 Jul 2026
14 days left
EMD
80000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Barmer → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair / Maintenance Of Joinery In Zone A Domestic Area At Af Stn Jaisalmer
BOQ
| Sl. No. | Item Description |
| 1 | Taking down shutters of any description exc 1.00 but n.exc 2.00 Sqm each complete all as specified and directed by Engr-in-Charge. |
| 2 | Taking down shutters of any description n.exc 1.00 Sqm each complete all as specified and directed by Engr-in-Charge. |
| 3 | Taking down window /ventilator/ door frame with shulters (without taking off shutters from the frames) area not exc 1.5 Sqm each |
| 4 | Taking down chowkats or frames with shutter (without taking off shutter from the frames) exc 1.50 Sqm but n. exc. 4 sqm each complete all as specified and directed. |
| 5 | M&L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing conforming to Fe290 Gde E-165 complete all as specified and directed. |
| 6 | S&F 35mm factory made second class hard wood 35 mm thick plain framed, panneled framed panneled shutter ( two panel) with lock rail and panel of 9mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both side face specification complete all as specified and directed by Engr-in-Charge. |
| 7 | S&F 30mm flush door shutters, soild core construction, with block board core and plywood face panels, commercial type both sides with and including 1mm thick plain colour PVC sheet fixed or laid on around the all side surface of flush doors by using rubber based adhesive as per specification complete all as specified and directed by Engr-in-Charge. |
| 8 | S&F for second class hardwood glazed and skeleton door shutters 35 mm thick, open rebated and prepared to receive glass, gauze, etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc , sizes of members of shutters as specified in SSR Part I, section 8, clause 8.24 (a) fitted to chowkat complete all as spd and as directed. |
| 9 | S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded single side prelam PVC 'C' channel instead of plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and single prelam PVC sheet used instead of plain colour PVC sheet and stile & rails having one side feathered edge and on other side 10mm 90degree bent edge & as gap insert for top rail & bottom rail;Panelling of single side prelam colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. complete all as specified and directed. |
| 10 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed |
| 11 | S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) frame/shutter work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including roller for sliding window, handle, locking device, necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 12 | S&F4.8mm thick sheet glass, ordinary quality n exc 0.5 sqm in each pane, fixed in doors/windows/Ventillators etc complete all as directed. |
| 13 | S&F 4.0 mm thick figured sheet glass as in panes and louvered ,n exc 0.5 sqm in each, fixed in windows/Ventillators etc complete all as directed. |
| 14 | S&F Stainless steel (Grade S 304) wire cloth 0.36mm nominal dia of wire and average width of aperture1.4mm and fixed with stainless steel wire staple fixed with aluminium beading etc complete all as specified and as directed. |
| 15 | S&F in repairs GI wire cloth 0.56mm nominal dia of wire and 1.18mm average width of aperture complete with beads etc. for steel/wooden door shutter/window shutter of any size/type/thickness complete all as specified and as directed. |
| 16 | Supply and fixing aluminium grill for aluminium window and ventilator as per direction of egr in charge |
| 17 | S&F aluminium (extruded section body) door closer hydraulically regulated designation No 3, universal type suitable for door shutters of 851 to 1000mm in width. |
| 18 | S&F 140 mm size floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor. |
| 19 | M&L preparation of new or previously untreated wooden surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engr-in-Charge. |
| 20 | M&L preparation of new or previously untreated steel surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 21 | M&L 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over and including cement screed bed in CM 1:6 laid and jointed in grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete necessary cutting, notching etc for sink. |
| 22 | M&L for Rounding to edges of stone slabs one edge such as in steps,cooking platform, window cill and other similer situations |
| 23 | S&F butt hinges medium weight cold rolled mild steel of size 125 mm fixed with stainless screws complete all as specified and directed. |
| 24 | S&F 250 mm long aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed. |
| 25 | S&F 200mm size aluminium anodised, barrel tower bolt of extruded section complete all as specified and directed. |
| 26 | S&F extruded aluminium alloy handles 150 mm long fabricated type anodised complete all as specified and directed. |
| 27 | S&F in repairs floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm. complete all as specified and directed. |
| 28 | S&F in repair 25mm dia stainless steel curtain rod with fancy type sides cups and brackets all as specified and directed by Engr-in-Charge, sample kept in GE office |
| 29 | S&F in repair 25mm dia powder coated curtain rod with fancy type sides cups and brackets all as specified and directed by Engr-in-Charge, sample kept in GE office |
| 30 | S&F in repairs Door closer hydraulically regulated aluminium (extruded section body), designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed in repair complete all as specified and directed by Engr-in-Charge. |
| 31 | S&F in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminum alloy sheet foundation box main body with stainless steel cover governing pivot made of brass , other prts made of mild steel heavey duty and fixed in repairs. complete all as specified and directed. |
| 32 | S&F in repair 4 lever vertical size 100mm mortice lock(Brass) for aluminium door as per direction of engr-in -charge. |
| 33 | Taking down/Dismantling of false ceiling boards of any description size or thickness including frame work etc complete all as directed. |
| 34 | S&F solid PVC fire resistant wall panelling/ Lining consisting of 5mm thick prelaminated PVC sheet inclusive of solvent cement & fixing at site on PVC frame etc complete all as per specifications and as directed.Note:- Rate shall be inclusive of refixing of dismantled E/M fittings and fixtures. |
| 35 | S&F 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall with screws to make PVC frame as per specification and drawing. |
| 36 | M&L for Anodised aluminium snap grid frame work for false ceiling as specified |
| 37 | S&F hangers from RCC soffit/Steel trusses with 6mm dia GI rod (upto 1200mm length) adjusting level fixed to roof by means of ceiling cleats made out of GI flat 40x3mm size 60mm long etc complete all as specified. |
| 38 | M&L 7 to 9 mm thick prelaminated design gypsum board for fixing in 600 mm x 600mm grid (Frame work for ceiling shall be measured and paid separately). |
| 39 | M&L in repair only 7 to 9 mm thick prelaminated design gypsum board for fixing in 600 mm x 600mm grid.. |
| 40 | Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed by Engr-in-Charge. |
| 41 | M&L 18/19 mm thick block boards, grade 2 quality, interior grade, decorative type with decorative face veneer on one face, fixed with screws to timber & iron frame-work as in cupbords shutters including suitable size of fillets to cover the edge of boards including hinges,fancy type handle, Magnet, complete all as specified and directed. |
| 42 | S&F figured glass 3.00 mm thick, pin head type and glazing with oil putty in squares/rectangle exc 0.5 Sqm in each pane complete all as specified and as directed and directed by Engr-in-Charge. |
| 43 | S&F glass pane ordinary quality 3mm thick not exc 0.50 Sqm each pane with fixing clips, putty or wooden beads and making good the surfaces matching existing surfaces fixing glass to wooden/ steel window/doors/alu doors etc. |
| 44 | Hacking out old broken glass any thicness size quality or description from metal frame incl puching or drilling out old glazing pin/spring clips and providing and fixing new once. |
| 45 | S&F in repair towel rail 600 mm long of chromium plated fixed incl screws complete all as specified and directed |
| 46 | S&F in repair towel rack 600 mm long of chromium plated fixed incl screws complete all as specified and directed |
| 47 | S&F in repair soap dish, any type, fixed to plugs with chromium platedbrass screws complete all as specified and directed. |
| 48 | S&F in repair stainless steel fancy type peg set 8. (not less 450 mm length) complete all as specified and directed by Engr-in-Charge. |
| 49 | S&F in repair 600 x 450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick PVC board and fixed to wooden plugs with chromium plated brass screws and cup washers. |
| 50 | S&F in repair bevelled edge looking mirror of selected quality glass, mounted on 6mm thick PVC board and fixed to wooden plugs with chromium plated brass screws and cup washers. |
| 51 | S&F in repair Bathroom mirror Cabinet (450x350mm) complete all as specified and directed by Engr-in-Charge. |
| 52 | S&F in repair Corner glass shelf 300mm 3 story (with ABS Brackets) complete all as specified and directed by Engr-in-Charge. |
| 53 | S&F in repair Kitchen rack (Overall size 600x600x300 mm) not less than 7.5 kg wt complete all as specified and directed by Engr-in-Charge. |
| 54 | Supply and fixing as in repair mild steel 300mm ordinary rat tail rod pattern springs (ISI marked) including roller and roller plate complete all as sp |
| 55 | Supply and fixing in repair 150mm long extruded aluminum handles fabricated type anodized, ISI marked. |
| 56 | Same as above but custom type decorated type made of brass as per direction of engr-in-charge. |
| 57 | Same as above but custom type decorated type made of SS as per direction of engr-in-charge. |
| 58 | M & L in reapir 12mm thick plain/froasted toughened glass door including stainless steel door handle 300mm long decorative type incl all necessary connected fittings and fixtures for door all as specified and directed. |
| 59 | M&L for PVC Shutter made out of solid PVC form profile 18 mm thick homogeneous fine cellular structure panelled having styles and rails of size 45 mm x 20 mm joints mitred at corners. The panel shall be made of 3 mm thick HPL sheet cover with moulding of size 35 mm 15 mm in any colour both side including stainless steel modular hinges,magnet catchers, handles &Knobs etc Make: Hettick. PVC sheet make -Accucel / Rajshree / Duroplast. |
| 60 | M&L for stainless steel basket of different pattern like plate rack,bottle rack etc,fixed with and including adjustable sliding steel channels to kitchen cabin,pattern and no of steel racks will be specified and directed . Make -Godrej/steel |
| 61 | Easing of Allu doors/window/ventilator shutter any thickness, any size and repair by Pvc rubber beeding, including tightening of hinge screw, by adjusting/tightening of tower bolts, sliding bolts etc and making it fully functional complete. |
| 62 | Easing of wooden doors/windows/ventilator shutters any thickness, any size by planning with plane jack, by tightening of hinge screws, by adjusting/ tightening tower bolts, sliding bolts etc and making it fully functional complete all as specified and directed. |
| 63 | Easing of steel windows/ventilator by adjusting projecting type hinges by hammering, oiling/greasing to hinges, adjusting handles of peg stay, including welding Etc, making the window shutter fully functional complete all as specified and directed |
| 64 | 6mm thick plain, PVC sheeting, as in sheet lining to PVC door fixed with screws / nails of suitable size fixed as in repair complete all as specified and directed. |
| 65 | 5 mm thick plain, wood ply sheeting, as in sheet lining to wooden door fixed with screws / nails of suitable size fixed as in repair complete all as specified and directed. |
| 66 | Wodden snap beeding for wooden glazed door with necessary self tapping reviting / screwing and suitable method as directed including taking down existing complete all as specified and directed. |
| 67 | \\"V\\" type stainless steel hinge of size 75mm x125mm x 5mm fixed as in repair complete all as specified and as directed . |
| 68 | 300mm long helical door spring mild steel including roller and roller plate complete all as specified and as directed |
| 69 | Supply and fixing in repair 100mm long butt hinges stainless steel medium weight ISI marked. |
| 70 | Supply and fixing in repair 250mm long Stainless steel barrel tower bolt of extrude section ISI marked. |
| 71 | S&F in repair 300mm long stainless steel sliding bolts, with bright bolt not less than 12mm dia all as specified |
| 72 | Supply and fixing in repair 50 mm long fancy type handle for cup board as per spd and directed. |
| 73 | Supply and fixing in repair pvc fancy type knob for cup board as per spd and directed. |
| 74 | Supply and fixing in repair pinao hinge for cup board as per spd and directed. |
| 75 | Supply and fixing in repair 3 D hinge(Daddo kabja) for cup board as per spd and directed. |
| 76 | M & L in repair 1 mm thick vaneer mica laminated over door, cupboard etc all as specified and directed. |
| 77 | S&F cupboards/ wardrobes, factory made, framed shell be of 1.25 mm thick pressed steel PGI sheet of size 90x70mm shutter shall made of 1mm thick pressed steel with 6 Nos of 100 mm lomg hinges 3.15mm thick steel hinges standard pattern rim lock with complete locking arrangement including 12 mm vertical rod shall be provided (brass mortice lock vertical type, size 65mm, 2 levers, ISI marked with escutcheon plate abd two key and with including two coats of spray painting with synthetic enamel paint of approved over a coat of primer including fixing with minimum 6 Nos 12 mm dia mild steel bolts 150mm long grouted in brick wall/ concrete including (Taking down old cupboard) making good the distrubed surfaces as original with CM (1:4) or PCC (1:2:4) type B0 complete all as spd and directed.Noted :- the measurement shall be taken of front elevation and not girtwise. |
| 78 | Attending petty complaints of carpenter nature such as hinge repair, door repair, window repair, repair/ repalcement of builder hardware etc all as per directed by Engr-in-charge. (Note:- These store will be issued by departement at complaint cell). |
| 79 | Attending petty complaints of welding nature such as welding hinges to iron frame of door and window, welding of wicket gate, welding of holdfast, guide rails etc all as per directed by Engr-in-charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 03, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 23, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 14 daysJul 25, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 16 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender