Tender For Repair And Maintenance Of Otm Accn In Guards, Stn Cell, Eme Bn And Aps Under The Area Of Age B/R-I Of Ge (A) No 1 Jodhpur
Tender Value
45 Lakhs
Estimated cost
Bid Submission
23 Jul 2026
15 days left
EMD
90000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jodhpur → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair And Maintenance Of Otm Accn In Guards, Stn Cell, Eme Bn And Aps Under The Area Of Age B/R-I Of Ge (A) No 1 Jodhpur
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) and removal unserviceable materials, debris and rubbish to a distance out side MD land complete all as specified and as directed. |
| 2 | Demolition of cement concrete of any description and in any position not otherwise specifically provided for (such as copings, bands of any type, roof padding, kerbs, sunken etc;) overall thickness and removing the dust debris etc to a distance not exceeding 250 meter from site and disposing the same complete all as specified and as directed by Engineer in charge. |
| 3 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), including removing broken tiles and the all rubbish off from the premises complete all as specified and directed. |
| 4 | Demolition of stone / boulder masonry walling or brick or PCC block masonary, built in cement mortar including all quoins, arches, pillars etc and removal unserviceable materials, debris, rubbish to out side MD land complete all as specified and directed. |
| 5 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exceeding 1.50 sqm each and removing from site and making good disturbed surface of walls in cement mortar (1:3) complete all as specified & directed. |
| 6 | Taking down chowkhats or frame with shutters (without taking of shutters from the frames) area exc 1.5 Sqm but not exceeding 4 Sqm each and removing from site and making good disturbed surface of walls in cement mortar (1:3) complete all as specified & directed. |
| 7 | Taking down shutters of any description exceeding 1.00 Sqm but not exceeding 2.0 Sq m each and removing from site, complete all as specified and directed by Engr-in-Charge . |
| 8 | Taking down shutters of any description exceeding 1.00 Sqm but not exceeding 2.0 Sq m each, and removing from site, complete all as specified and directed by Engineer-in-Charge |
| 9 | S & F 35 mm thick, factory made, 2nd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass, gauze, etc. (divided into squares with plain, chamfered or rounded, mitred and rebated sash bars any number size of members), beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8 clause 8.24 (a); kiln seasoned & chemically pressure treated etc complete all as specified and directed . (Note:-Glass / wire cloth shall be measured & paid separately.) |
| 10 | Supply,Providing and fixing factory made single extruded WPC(Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 Kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/Sq. mm, modulus of elasticity 850 N/Sq.mm and resistance to spread of flame of Class- A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with including stainless steel butt hinges of required size & numbers with necessary full body threaded star headed counter sunk S.S screws, all as per directied by Engineer-in- Charge complete all as specified and directed. |
| 11 | M & L for factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 mm x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/Sq.mm, modules of elasticity 900 N/Sq.mm and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantFactory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 mm x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/Sq.mm, modules of elasticity 900 N/Sq.mm and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with & including mild steel hold fast/lugs/SS dash fasteners of required dia ,numbers and length complete as per directed by Engineer-in-Charge complete all as specified & directed. |
| 12 | M&L for framed brackets for cooler stand made of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc. not exceeding 10 kg each brackets, conforming to Fe.290.Gde-E-165 and used for step/stairs, walk ways, railings, frame work of water tanks and similar work complete all as specified and as directed. |
| 13 | S&F of factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made of mild steel tubes for top & bottom rail. mild steel frame shall be covered with heat moulded plain color PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain color PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted to the mild steel frame/sealed to the stiles & rails with suitable PVC sheet beading, and joined 30mm thick (style) consisting of frame made of mild steel tubes for top & bottom rail. mild steel frame shall be covered with heat moulded plain color PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain color pvc sheets for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail paneling of plain colour PVC sheet to be fitted the mild steel frame/sealed to the stiles & rail with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and directed. |
| 14 | S & F solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tubes suppyling & fixing in opening as per specification & drawing complete all as spcefied and directed by Engineer-in-Charge. |
| 15 | S & F Aluminium anodised handles of extruded section and fixed 125 mm long complete all as specified & directed. |
| 16 | S&F aluminium anodised barrel tower bolts of extruded section of 200 mm size complete all as specified and as directed. |
| 17 | S&F 300 mm long aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. |
| 18 | S&F butt hinge of size 100mm , medium weight, cold rolled mild steel, complete all as specified and as directed. |
| 19 | S&F stainless steel butt hinge of size 100mm, complete all as specified and as directed. |
| 20 | S & F floor door stopper of alluminium alloy anodised door stopper with rubber shoes body and toungue anodised with hard drawn steel spring 140mm long complete all as specified and directed. |
| 21 | M&L for plain cement concrete 1:2:4, type B-0 (using 12.5 mm graded crushed stone aggregates) as in levelling course,kerb/ benching/ coping /window cill etc including weathering, slightly rounded or chamfered angle and throating including use & waste of necessary form work etc complete all as specified and directed. |
| 22 | S&F 5.0 mm thick sheet glass, selected quality and glazing in squares/ rectangular exceeding 0.5 Sqm in each pane glazing with oil putty or aluminium frame/shutters with rubber neoprene beading complete all as specified & directed. |
| 23 | S & F in repair for aluminium (extruded section body) Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 mm to 1000 mm in width and of weight between 61 to 80 kg and fixed complete etc all as specified & directed. |
| 24 | S&F of brass body mortice lock, vertical type, size 100 mm long four levers (ISI marked) for aluminium door (as per sample) complete all as specified and directed. |
| 25 | S&F for fabrication aluminium work for powder coated (with coating layer of minimum 50 micron thick) as in frames for doors, windows, ventilators & doors(fixed/ sliding track two or three track) and partitions frames with extruded built up standard sections of approved make fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions with sealent with wall, i.e. at top, bottom and sides including cleat angle,C.P. brass/ stainless steel screws, with louvers having suitable mechanism for tilting , U shaped fillets all complete all as specified and directed. |
| 26 | M&L for pre powder coated (with coating layer of minimum 50 micron thick) aluminium decogrill size 50mm x50mm size of mesh and 6mm dia, fixed to aluminium framework of windows & ventilators complete all as specified and as directed. |
| 27 | S&F powder coated (with coating layer of minimum 50 micron thick) aluminium shutters ,aluminium section (min weighing 0.55 kg/m) including necessary joining cleats, glazing clips rubber packing,anodised aluminium snap beading, screws, powder coated aluminium fittings such as peg stays 150mm long (1No.),100mm long hinges type B-21 (2Nos), suitable handle(02 Nos.) in each door shutter top rail guide rail etc.complete all as specified and directed.Note : Glass panes & aluminium wiremesh shall be measured & paid for seperately. |
| 28 | S&F in replacement of galvanised mild steel wire cloth 0.35mm nominal dia of wire and average width of aperature 1.40mm, complete all as specified and as directed. |
| 29 | S & F 5.50 mm thick plain sheet glass area not exceeding 0.5 Sqm in each pane of superior quality fixed to aluminium frame work with rubber neoprene beading including solar control film 50 micron reflective type sticked to glass panes as per manufacturer;s instructions of manufacturers complete all as specified & directed. |
| 30 | S&F solar control film 50micron thick non-reflective type sticked to glass panes as per manufacturer's instructions complete all as specified and as directed. |
| 31 | S&F lnsulated PVC wall lining consisting of PVC insulated panels having expanded polystyrene (EPS) stuck to 2.0 mm thick plain colour PVC sheet duly fitted into the wall as per specifications and drawing thickness of insulated PVC wall lining 12 mm complete all as specified and directed |
| 32 | Dismantling wall and ceiling boarding, any description,including frame work & cover fillets etc., fixed in any position with nails/screws complete removal of old connecting snap grid and hangers complete all as specified and directed by Engineer-in-charge. |
| 33 | S & F for providing aluminium snap grid frame work for false ceiling system with size 605 mm x 605 mm, consisting of main runner of size 36.5 mm x 25 mm x 1.4 mm (weight not less than @ 0.24 Kg/Rm) and cross Tee of size 23.5 mm x 36.4 mm x 1.4 mm (weight not less than @ 0.191 Kg/Rm). The snap grid shall be supported at end all along the wall with aluminium anodised angle of size 40 mm X 25 mm X 2 mm (weight not less than @ 0.36 Kg/Rm).The snap grid shall be fixed to ceiling supporting hangers consisting of 6 mm dia. G.I wire , J-bolts ,nuts and washers as per manufacturer's instructions or adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long and complete all as specified and directed by Engr-in-Charge |
| 34 | S & F for providing gypsum board 12mm thick in ceiling fixed with screw as per manufacturers instructions complete all as specified and as directed. |
| 35 | M & L for preparing new or previously untreated wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint (Ordinary tint) over & including a coat of pink primer complete all as specified and as directed. |
| 36 | M&L for preparation of old painted wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint on wooden surface complete all as specified and as directed . |
| 37 | M&L for prepartion of new or previously untreated steel surface of any description , not otherwise described, over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed. |
| 38 | Hacking out old boken glass(any thickness, size, quality or description) from wooden frames/steel frames, glazed with oil putty or fixed with beads, including punching or drilling out old glazing pins/ spring clips and provding and fixing new ones, complete all as specified and directed |
| 39 | M & L for 3mm thick plain sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.50 Sqm in each pane,complete all as specified and as directed by Engineer-in-Charge . |
| 40 | S&F 4.0 mm thick frosted glass pin headed type in squares/ rectangular not exceeding 0.5 Sqm in each pane glazing with oil putty or aluminium frame/shutters with rubber neoprene beading complete all as specified & directed. |
| 41 | S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples etc complete all as specified & directed. |
| 42 | Taking down cement plaster on brick wall or concrete surface or on stone walls etc including raking out joints hacking for key scrubbing down with water etc & removing the debris from the premises upto 500 m from the MOD land complete all as specified and directed |
| 43 | M&L for 15 mm thick rendering in CM 1:6 on stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing finished surface even and smooth without using extra cement, complete all as specified and as directed. |
| 44 | M&L for 10mm thick rendering in cement mortar 1:3 on concrete ceiling surfaces / sunsheds / facia / RCC chajja, finished even and smooth without using extra cement, complete all as specified and directed.Note -Rate are deemed to be included for scaffolding, trestles, ladders, cradles, etc. necessary for execution of work and protective measures.. |
| 45 | M&L for 15 mm thick rendering in CM 1:4 on stone masonry/concrete surfaces/roof projections/chajjas upto the height 7 Mtr finished surface even and smooth without using extra cement including necessary scaffolding provided at site, complete all as specified and as directedNote -(i) Unit rate are quoted by bidder, deemed to be included for scaffolding, trestles, ladders, cradles, etc. necessary for execution of work and protective measures. |
| 46 | M&L for racking out joints/ pointing to squared rubble or polygonal rubble un-coursed or brought up to courses masonry built in cement mortar or cement lime mortar, coursed or un-coursed in walls not less than 12mm deep, washing the joints, removing rubbish off the premises and keeping the surface to pointed or plastered wet for two days prior to re-pointing or plastering complete all as specified & directed. |
| 47 | M&L keyed pointing in cement mortar (1:3) to squared rubble masonry regular coursed or un coursed, complete all as specified & directed. |
| 48 | M&L for preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white wash on wall surfaces complete all as specified and as directed. |
| 49 | M&L for preparation of old plastered or unplastered surfaces of ceiling and applying two coats of white wash on ceilings surfaces complete all as specified and as directed. |
| 50 | M & L for preparation of new plastered or unplastered surfaces of wall and applying with 2.0 mm thick(minimum) wall care putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of oil bound distemper (shade or tint as approved by GE), over a coat of with alkali resistant priming paint on walls surface complete all as specified and as directed |
| 51 | M&L for complete removal of old/existing treatment from walls (any number of layers) by scrapping with steel scrappers or any other means, including filling depressions of scrapped surfaces with preparation of plastered surfaces and apply two coats of distemper oil emulsion (OBD) over a coat of alkali resistant primer applying by pump roller applicator of any shade or tint over & including applying 1.0 mm thick wall care putty(make:J K /BIRLA) to make entire surface free from undulations complete all as specified and directed. |
| 52 | M&L for preparation of newly plastered surfaces of walls/chajja/lintel and applying two coats of cement based paint white or tinted over a coat of alkali resistant primer complete all as specified and directed by Engineer-in-Charge |
| 53 | M&L for complete removal of existing treatment from walls (any number of layers) by scrapping with steel scrappers or any other means, including filling depressions of scrapped surfaces with preparation of plastered surfaces and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives applied @ 1.43 Ltr/10 Sqm,over and including priming coat of exterior primer applied @ 0.90 lit/10 Sqm over a coat of 2 mm thick putty,applying by bump roller applicator complete all as specified and directed. |
| 54 | Taking down aluminium doors/window shutters only (area exceeding 0.50 sqm but not exceeding 4.0 sqm each) and dismantling all members for repairing and re-assembling the same with replacement and including new hinging device, handles, loose glass, rubber gasket,screws, new aluminium beads & cleats of existing make and also refixing the handles & mortice locks in existing position with and including refixing the door/window shutters in same opening complete all as specified & directed. Note: Hydrolic door closer, door spring,glass etc.,,if required shall be measured and paid seperately under respective items. |
| 55 | M&L for powder coated aluminium door seal 1000 mm long, 30 mm wide including dust/insect arrestor with screws,nails etc complete all as specified and directed. |
| 56 | Resucuring /easing and adjusting shutters of any description and in any position area not exceeding 1.0 Sqm including taking down of shutter from frames & refixing in the same opening after completion/necessary of repair works, complete all as specified and as directed. |
| 57 | Resucuring /easing and adjusting shutters of any description and in any position area not exceeding 1.0 Sqm but not exceeding 2.0 Sqm including taking down of shutter from frames & refixing in the same opening after completion/ necessary of repair works, complete all as specified and as directed. |
| 58 | Resucuring /easing and adjusting shutters of any description and in any position area not exceeding 2.0 Sqm but not exceeding 4.0 Sqm including taking down of shutter from frames & refixing in the same opening after completion/ necessary of repair works, complete all as specified and as directed. |
| 59 | S &F in replacement of hexagonal nipple of water tanks of existing/suitable size or dia complete all as specified and directed. |
| 60 | S&F in repairs decorative type curtain rod stainless steel finish of pipe 22 to 25 mm dia (1.0 mm wall thickness) with best quality knob metal with double fitting type including stainless steel brackets fixed to walls with two nos decorative stainless steel knobs at each end,including fixing with fancy brackets,stops, rollers etc.,complete all as specified and as directed by Engineer-in-Charge. Note: Running length of curtain rod shall be measured & paid only. |
| 61 | M&L for 75mm thick PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate), as in sub base to floor, complete all as specified and directed. |
| 62 | M&L 40 mm thick PCC 1:2:4 type B-1(using 20mm graded crushed stone aggregate )as in flooring/hard standing laid in alternative bays using with & including glass dividing strips including finishing cement concrete surface even and smooth without using extra cement complete all as specified & as directed. |
| 63 | M & L for 50 mm thick plain cement concrete(1:3:6) mix, type C-1(using 20mm graded crushed stone aggregate ) laid in alternative bays as in plinth protection, finishing the surfaces even and fair without using extra cement, including 10 mm wide, 50 mm deep joints made at 3.00 m in length and filled with the joints with mastic filling in the ratio 1:3 i.e one part of bitumen 85/25 and 3 parts of sand by weight in 2 mtr interval including necessary form work,complete all as specified and directed. |
| 64 | Supply and laying machine pressed / factory made chamfered edge cement concrete rubberised interlocking paver block, 60mm thick with 6 mm thick top layers of anti abrasive material of M-35 grade with any colour, design & pattern, & size/ shape, as approved by GE as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed. |
| 65 | M &Lfor providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 part cement : 3 part coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete all as specified and directed. |
| 66 | M & L for machine pressed chequered cement concrete tiles, rubber moulded 300mm x 300mm x 20-25mm thick, set, jointed and pointed in neat cement slurry with grey cement and no pigment ,laid over and including 20 mm thick cement screed bed in cement mortar (1:4) complete all as specified and directed. |
| 67 | M&L for 25 mm thick plain cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in subbase of floor to receive tile finishes, complete all as specified & directed. |
| 68 | M&L for joint free non skid ceramic coloured tiles (premium quality) of size 7 mm to 8 mm thick (square/rectangular) area of each tiles exceeding 0.06 Sqm but not exceeding 0.11 Sqm (size & shape, shade and pattern as approved by GE), as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, over and including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed. |
| 69 | M&L for 10 mm thick virtrified ceramic (Light shade) tiles polished area of each tile not exceeding 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match, over and including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed. |
| 70 | M & L for 10mm thick vitrified ceramic ( Light shade) tiles polished area of each tiles not exceeding 0.36 Sqm, laid in vertical surface as in dado/skirting etc over & including 10 mm thick rendering in CM 1:4,set & jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed. |
| 71 | M&L for 10 mm thick virtrified ceramic (Light shade) tiles polished area of each tile exceeding 0.42 sqm and not exceeding 1.20Sqm, as in floors etc., set and jointed in neat cement slurry and pointed in coloured cement to match, over and including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed. |
| 72 | M&L for joint free non skid ceramic coloured tiles (premium quality) of size 7 mm to 8 mm thick (square/rectangular) area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm (size & shape, shade and pattern as approved by GE), as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, over and including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed. |
| 73 | M&L for joint free non skid ceramic coloured tiles (premium quality) of size 7 mm to 8 mm thick (square/rectangular) area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm (size & shape, shade and pattern as approved by GE), laid in vertical surface as in dado/skirting etc over & including 10 mm thick rendering in CM 1:4,set & jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed. |
| 74 | M & L glazed ceramic coloured tiles (premium quality) of size 350 mm x 250 mm x7mm thick / 450 mm x 350 mm x7mm thick ,as in vertical surface such as dado/skirting et ,set and jointed in neat cement slurry and pointed in colour cement to match the tiles,over & including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed. |
| 75 | M&L for 20 mm to 25 mm thick machine cut pre-polished stone slab as in floor (size not less than 580mm x 580mm),treads, steps etc(Single piece for steps),laid over & including 15mm thick in screed bed in CM (1:6) and jointed with grey cement slurry with pigment to match the shade of the slab,including grinding, rubbing with bees wax polishing into mirror finish including demolition of stone slab, laid bedded and pointed in any mortar complete all as specified & directed. |
| 76 | M&L for machine cut kota stone slab 16 mm -18 mm thick as in risers , riser of step, dado, steps, tread, skirting etc., laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 10mm thick rendering in CM 1:4 including dismantling of stone slabs of any description complete all as specified and as directed. |
| 77 | M&L for 15 to 18 mm thick Udaipur green stone in single piece as required, as in tread, cills, steps, risers, cooking platefoRM & etc., machine cut, (table rubbed and granite polished) best quality as per sample, over & including 15 mm thick screeding in CM1:4 including rounding & double mouldlng with jointless finish of the edges, including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of stone, complete all as specified and as directed. |
| 78 | M&L for 18 to 20 mm thick (telephone black shade) granite stone, as in WHB counter top, steps, jambs, pillars, window cills & similar nature works, machine cut,(table rubbed and polished) best quality as per sample, over & including 15 mm thick screeding in CM1:4 including rounding & double mouldlng with joint less finish of the edges, including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.& providing suitable dia hole in the slab for the gas pipe,complete all as specified and as directed. |
| 79 | Dismantling structural steel work including doors, gates but excluding framed truss etc.,complete all as specified and as directed. |
| 80 | M&L for rolled mild steel confirming Fe-290 (Gde E-165) in door or gates of angle or other section with gusset plate, rail braces etc complete drilled for fixing of steel sheeting or other covering, doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel, sheeting or other covering ) and hanging also fastening and fixing complete all as specified and as directed. |
| 81 | M&L stone slab 5 cm thick dressed true and square, in one length not less than 60cm and not exceeding 200 cm as in copings, window cills, chajjas, sunshades,plinth protection etc, punched dressed on exposed faces and self faced on the embedded unexposed beds and joints, exposed edges rounded or chamfered as directed, set, jointed and pointed in cement mortar 1:4 complete all as specified and as directed |
| 82 | M&L for squared rubble walling, Jodhpur type, regular coursed well bonded ,bedded and solidly hearted built in cement mortar 1:6, complete all as specified and directed. |
| 83 | M&L for squared rubble walling, Jodhpur type, regular coursed well bonded ,bedded and solidly hearted built in cement mortar 1:6,but except stone complete all as specified and directed. |
| 84 | Extra over stone walling for hammer dressing to face stone & dressing of face beds & joints as specified of squared rubble walling Jodhpur type brought upto courses with maximum depression of face from straight edge held against the dressed surface not exceeding 20mm and dressing face beds and joints, complete all as specified and directed. |
| 85 | M&L precast cement concrete (1:2:4) type B-1(using 20mm graded crushed stone aggregate) as in solid building block or slabs 10cm thick and setting in cement mortar 1:4 complete in wall all as specified & directed by Engineer-in-charge. |
| 86 | M&L precast cement concrete solid building blocks masonery 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) solid blocks, exceeding 10 cm in width and setting in cement mortar 1:6, straight or curved on plan exceeding 6 m mean radius complete all as specified and directed. |
| 87 | S & F in replacement white vitreous China squatting pan \\"Orissa pattern\\" of size 580 mm X 440 mm with integral foot rests and PVC 'P' or 'S' trap, with & including brackets, flush HDPE pipe of 32 mm dia and PVC connection 15mm size, 450 mm long with PTMT nuts & fixing arrangement of cistern, complete all as specified and as directed. |
| 88 | S&F in repair vitreous China wash down water closet (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe), including plastic seat cover connection to drain (or outgoing pipe, and to flushing pipe & antisyphonage pipe etc with aluminium hinging device including provision of lime concrete bedding white and making good floor including Plastic water closet seat cover, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device for pedestal pan complete all as specified and directed. |
| 89 | S&F in replacement of Single piece EWC with slim soft close seat cover complete set constellation dual flush (WB consetellation 5 ped constellation, EWC, cistern & lid CON dual flush, seat cover constellation, cistern fitting (water saver-dual flush) etc complete all as specified and directed by Engr -in- charge. |
| 90 | S & F in repairs vitreous china ware wash hand basin, white, flat back of size 300 mm X 450 mm including 32 mm dia brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, cutting for and pinning in ends of brackets or erecting strand, 32mm bore PVC flexible waste pipe,PVC connection15mm size with PTMT nuts of length 450mm long screwed for iron pipe complete all as specified and as directed, |
| 91 | S & F in repair stainless steel kitchen sinks with drainage board for kitchen made of stainless steel 1.00 mm thick sheet with plugs, washers & waste coupling and waste pipe, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe (overall size 495mmx 420mm bowl size 410mm x 330mm x160mm) including 40 mm bore PVC flexible waste/flush pipe 800mm long with socket fixed with sink brass waste coupling complete all as specified and directed. |
| 92 | S & F in repair PVC flushing cistern 10 ltr capacity valve less syphonic action type low level with and including all standard accessories such as inlet ball valve float and handle, PVC flush pipe 32 mm bore & PVC connection 15 mm bore 450 mm long with PTMT nuts and brackets complete set & making good disturbed surface with CM 1:3 complete all as specified and directed. |
| 93 | M&L replacement of internal flushing cistern fitting (accessories kit) for low level, make as per existing fitting all as specified and as directed. |
| 94 | S & F in repair for PVC connection 15 mm dia size with PTMT nuts of length 450 mm complete all as specified and directed. |
| 95 | S&F in repair 15mm bore long body (weight not less than 400 gm) bib tap, cast copper alloy, CP fancy type with crutch or with spindle,half turn with, screw down, screwed for iron pipe or for brass ferrule including flange complete all as specified and directed |
| 96 | S&F in repair 15mm bore long body two way bib cock, cast copper alloy, CP fancy type with crutch or with spindle,half turn with, screw down, screwed for iron pipe or for brass ferrule including flange complete all as specified and directed |
| 97 | S & F in repairs 15mm dia bore stop valve cast copper alloy fancy type, chromium plated with long shank and cup screwed down high pressure with crutch or butterfly handle screwed bot ends for iron pipe or for unions complete all as specified and directed |
| 98 | S & F in repairs 20 mm dia bore stop valve cast copper alloy fancy type, chromium plated with long shank and cup screwed down high pressure with crutch or butterfly handle screwed bot ends for iron pipe or for unions complete all as specified and directed |
| 99 | S&F in repairs 15mm dia bore angle stop valve cast copper alloy fancy type, chromium plated with long shank and cup (concealed type) screwed down high pressure with crutch or butterfly handle screwed bot ends for iron pipe or for unions complete all as specified and directed |
| 100 | S & F 15mm bore angle stop cock cast copper alloy, fancy type chromium plated with long shank and cup screwed down,high pressure with crutch or butterfly handle, screwed both ends for iron pipe complete all as specified and directed. |
| 101 | S & F in repairs bib tap standard of PTMT any colour high pressure screwed for iron pipe & fixed (minimum weight 15 mm 90gm), screwed both ends for iron pipe etc complete all as specified and as directed. |
| 102 | S & F in repairs pillar taps chromium plated, cast copper alloy with capstan head, screwed down with or without lettered 'Hot' or 'Cold' with long screw shanks and fly nuts, screwed for iron pipe and fixed for 15 mm bore complete all as specified & directed |
| 103 | S&F in repairs PVC flexible waste pipe 32 mm to 40 mm dia with socket for steel sink/WHB upto floor level and any length but not less than 0.85 Mtr, complete all as specified and as directed. |
| 104 | S&F in repair 15 mm bore CP brass two way angular stop cock, screwed down high pressure with crutch or butterfly handle scrwed both ends for iorn pipe complete all as specified and directed. |
| 105 | S&F in replacement ,15mm dia Hand Shower (Health Faucet) with 8mm dia, 1.2 meter long flexible tube & wall hook with N.R.V (back flow preventer) complete all as specified and as directed. |
| 106 | S&F in repair 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 107 | Dismantling existing water tank of capacity not exceeding 500 ltrs and removing from site, complete all as specified and as directed. |
| 108 | Dismantling existing water tank of capacity exceeding 501 ltrs and not exceeding 1000 ltrs and removing from site, complete all as specified and as directed. |
| 109 | S&F rotational moulded polythene water storage tank of capacity 500 ltrs (cylindrical/vertical with closed type), triple layer construction, ISI marked, hoisted and fixed in position including 20 mm bore GI nipple and 20 mm bore ball/ float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 210 gms) complete all as specified and directed. |
| 110 | S&F rotational moulded polythene water storage tank of capacity 1000 ltrs (cylindrical/vertical with closed type), triple layer construction, ISI marked, hoisted and fixed in position including 20 mm bore GI nipple and 20 mm bore ball/ float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 210 gms) complete all as specified and directed. |
| 111 | Disconnecting existing tanks,capacity not exceeding 500 ltr , setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position.Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc complete all as specified and directed. |
| 112 | S & F in repair for 20 mm dia ball valve, high pressure of PTMTwith epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (minimum weight -210 gms) complete all as specified and directed. |
| 113 | Cleaning and removing all scale and dirt etc from over head water tanks and from mouths of circulating pipe etc including dismantling & refixing at same or other place of capacity exceeding 250 ltrs but not exceeding 500 ltrs complete all as specified and directed. Note :- If any accessories damaged occur during the cleaning of tank, the same shall be replaced by the contractor at his own arrangement and nothing extra shall be paid. |
| 114 | Cleaning and removing all scale and dirt etc from over head water tanks and from mouths of circulating pipe etc including dismantling & refixing at same or other place of capacity exceeding 500 ltrs but not exceeding 1000 ltrs complete all as specified and directed. Note :- If any accessories damaged occur during the cleaning of tank, the same shall be replaced by the contractor at his own arrangement and nothing extra shall be paid. |
| 115 | M & L for plain cement concrete 1:2:4 ,type B-1 (using 20 mm graded crushed stone aggregate) as in padding, benching, sunken portion etc., on roof surface for correcting/making proper slope on roof, etc.,complete all as specified and directed |
| 116 | M & L for application of water proofing treatment over non accessible/ non approachable RCC roof slab / chajjah / canopy / parapet wall( horizontal/vertical surface) to be executed through approved applicator of the membrane manufacturer/authorized applicator of the manufacturer with following specification etc complete all as specified and directed :- (i) Cleaning existing surface properly with wire brush .(ii) Rendering / bedding layer of 15 mm thick in CM 1:4 mixed with water proofing compound as per manufacturer instructions laying of water proofing treatment including providing the following stage as roof treatment complete all as specified and as directed by Engr-in-Charge : - (iii) Material and labour for UV stable single component fibre reinforced elastomeric liquid applied waterproofing membrane having solid content of 55% formulated wih PU hybrid polymers and reinforcing acrylic fibres and having sun reflectivity Index (SRI) of 106. The application of the material should be done in three coat (6 hr gap after each coat) on the substrate, applying first self priming coat at ratio of damp proof ultra and water 3:1 then 2 undiluted coat of damp proof ultra obtaining coverage @1 ltr/10 sqft in two coats (10-12 hrs gap between each coat. The vital physical and chemical parameters shall be as under. Min elongationat break of 350%, crack bridging ability of 2.5 mm @650 microns thickness, resists positive hydrostatic pressure of up to 10 bars. The material shall be appliied with brush or roller, complete in all respect as per the direction of Engr-in charge/consultant. Also, proper surface preparation along with covingat corners is must. Note : -(i) The work shall be executed by the authorized applicator of the manufacturer only.(ii) The authorized applicator of manufacturer shall be approved by GE, (iii) The color of final finish shall be decided by the GE. (iv) .WPC shall be measured and paid separately under respective item. |
| 117 | Taking up or down steel tubing/CPVC pipe and connections of 25 mm bore or removal to store complete etc and making good the surface in cement mortar 1:3 complete all as specified & directed, |
| 118 | Taking up or down steel tubing/CPVC pipe and connections of 20 mm bore or removal to store complete etc and making good the surface in cement mortar 1:3 complete all as specified & directed, |
| 119 | Taking up or down steel tubing/CPVC pipe and connections of 15 mm bore or removal to store complete etc and making good the surface in cement mortar 1:3 complete all as specified & directed.. |
| 120 | Supplying and laying of CPVC pipes, 16 mm outer dia of pipe, SDR 11 & Plain CPVC SDR 11 including all brass fittings, laid in trenches or ceiling or fixed to wall including cutting chases, pinning in & making good to disturbed portion complete all as specified & directed. |
| 121 | Supplying and laying of CPVC pipes, 20 mm outer dia of pipe, SDR 11 & Plain CPVC SDR 11 including all brass fittings, laid in trenches or ceiling or fixed to wall including cutting chases, pinning in & making good to disturbed portion complete all as specified & directed |
| 122 | Supplying and laying of CPVC pipes, 25 mm outer dia of pipe, SDR 11 & Plain CPVC SDR 11 including all brass fittings, laid in trenches or ceiling or fixed to wall complete all as specified and as directed. |
| 123 | M & L providing 35 mm/40mm thick pre-cast cement concrete 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) as in louvers,, cement grill any type model of zafri & jallies (measured solid) including all mouldings and including pre-cast frames, set in cement mortar 1:6, including dismantling old existing jallies, complete all as specified and as directed. |
| 124 | M & L providing precast concrete posts size (100mm x 100 mm x 750mm) & (100 mm x 100 mm x 600 mm) of PCC 1:2:4, type B-0(using 12.50 mm graded crushed stone aggregate) as in RCC/PCC jali post , setting in mortar 1:6, including necessary required reinfocement for strengheng of post & dismantling old existing Post, complete all as specified and as directed.. |
| 125 | S&F of roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc confirming to (Fe 410-W grade E-250) quality complete all as specified and as directed. |
| 126 | S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa & minimum AZ @150 gm/Sqm( be coated with hot dip alloy of 55 % aluminium, 43.5% Zinc, 1.5% Silicon and finished with resin coat on both surface @ 150 gm/Sqm of coating both surfaces) as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of existing sheet complete all as specified & directed. |
| 127 | Supply only water proofing compound ISI marked complete all as specified & directed. |
| 128 | (i) The contract sum shall be arrived at after deducting amount of schedule of \\"Credit\\" from the Total quoted amount. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 02, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 23, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 15 daysJul 30, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 22 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender