Tender For Certain Repair To Joinery, Tiling, Plumbing, Fencing, Compound Wall, Rolling Shutters, Painting & Allied Infra For Mes Installation At Mil Stn Dharamshala
Tender Value
Ref. Documents
Estimated cost
Bid Submission
23 Jul 2026
11 days left
EMD
40000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kangra → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Certain Repair To Joinery, Tiling, Plumbing, Fencing, Compound Wall, Rolling Shutters, Painting & Allied Infra For Mes Installation At Mil Stn Dharamshala
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level) including removal of debris to out side Mil Stn, complete all as specified and directed. |
| 2 | Demolition of cement concrete un-reinforced any description in any position including removal of debris to out side Mil Stn, complete all as specified and directed. |
| 3 | Dismantling floor hearth or wall tiling including cement mortar bedding ( but not backing ) removing serviceable tiles to store and rubbish off the premises etc complete all as specified and directed |
| 4 | Demolition of stone slabs and tiles of any description or thickness in floors, aprons laid, bedded and pointed in any mortar etc including removal of debris to out side Mil Stn, complete all as specified and directed. |
| 5 | Demolition of brick work/ block masonry or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles and including removal of debris to out side Mil Stn, complete all as specified and directed. |
| 6 | Dismantling posts or struts (wood, steel or RCC) any section, including taking out embedded portion and making good disturbed ground or lean concrete etc. complete all as specified and directed. |
| 7 | Taking down cement or cement lime plaster any description, on brick or stone walls, etc. including raking out joints, hacking for key & scrubbing down with water, etc. & removal of debris to out side Mil Stn, complete all as specified and directed. |
| 8 | Taking down chowkhats or frames & removing from site area not exc. 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed. |
| 9 | Taking down chowkhats or frames & removing from site area exc. 1.50 Sqm but not exc. 4.00 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed. |
| 10 | Taking down shutter of any description & removing from site area n.exc. 1 sqm each complete all as specified and directed. |
| 11 | Taking down shutter of any description & removing from site area exc. 1 sqm but not exc. 2 sqm each complete all as specified and directed. |
| 12 | Dismantling plain or corrugated steel sheeting any gauge, thickness in roofs complete all as specified and directed. |
| 13 | Taking up or down 15 mm bore steel tubing and connections including complete all as specified and directed. |
| 14 | Taking up or down 20 mm bore steel tubing and connections complete all as specified and directed. |
| 15 | Dismantling PVC water tank of capacity Exc 250 Litre and not Exceeding 500 Ltr complete all as specified and directed. |
| 16 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 17 | S & F of 2nd class hard wood scantling, clean sawn in any position and any description as in framed or unframed work including dismantling the old one complete all as specified and directed. |
| 18 | S&F of 3mm thick sheet glass ordinary quality and glazing type, n.exc. 0.5 sqm in each pane, duly fixed with oil putty or wooden beading as required incl hacking out old broken glass (any thickness, size, quality or description) from wooden frames or steel, concrete orbrick surround, glazed with putty or fixed with beads, complete all as specified and directed. |
| 19 | M&L 10mm thick rendering in cement mortar 1:3 on fair faces as in ceiling surfaces finished even and smooth without using extra cement, complete all as specified and directed. |
| 20 | M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:6 and finishing the surface even and fair without using extra cement complete all as specified and directed. |
| 21 | M & L for 15mm thick rendering in CM 1:4 on other than fair faces of brick masonry, stone masonry or concrete surfaces, mixed with water proofing liquid @ 2% by weight of cement and finished even and smooth without using extra cement upto 10m bldg ht complete all as specified and directed. (Note :- Water Proofing shall be measured and paid separately) |
| 22 | Supply only intergal Water Proofing complete all as specified and directed. |
| 23 | M&L PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed. |
| 24 | M&L for 40mm thick cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) in floor finished without even and smooth using extra cement complete all as specified and directed. |
| 25 | M&L for 75 mm thick PCC 1:3:6 type C-2 using 40 mm graded stone aggregate finished even and smooth without using extra cement as in plinth protection/ path/ hardstanding, laid in panels complete all as specified and directed |
| 26 | M&L for cement concrete 1:2:4, type B-1 (using 20mm graded crushed stone aggregates) as in cills, steps, seismic and other similar bands, plinth courses, copings, kneelers, apex stones, bed plates, bond stones etc. including weathering, slightly rounded or chamfered angles and throating including necessary formwork, complete all as specified and directed. |
| 27 | Providing precast cement concrete type B-0 1:2:4 (using 12.50mm graded crushed stone aggregate) as in louvres/jaffries and jallies, 25mm thick (measured solid) set in CM 1:6, including all mouldings but excluding frame of stone/brick/concrete complete all as specified and directed. |
| 28 | Providing precast cement concrete type C1 1:3:6 (using 20mm graded agg) set in CM 1:4 in landings, cover slabs (for man holes etc),chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces complete all as specified and directed. |
| 29 | S&F mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 30 | M&L for brick work with sub class 'B' bricks, old size, straight or curved on plan exc 6.0 mtr mean radius, built in CM 1:6, complete all as specified and directed. |
| 31 | M&L for walling of random rubble, uncoursed, brought upto courses, well bonded, bedded and solidly hearted, built in CM (1:6) complete all as specified and directed. |
| 32 | All as per Sr item No 31.00 above but except stone. |
| 33 | Extra over stone walling random rubble brought upto courses, for hammer dressing to face stones and dressing of face beds and joints, with maximum depressions on face from straight edge held against the dressed surface not exc. 20 mm on lime or sand stone, complete all as specified and directed. |
| 34 | M&L raised pointing to squared rubble stone masonry,un-courses or brought upto course in cement mortar 1:4 complete all as specified and directed. |
| 35 | M & L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square or Rectangular) area of each tile exc. 0.11 Sqm but not exc. 0.18 sqm(400x400), as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile, incl 15 mm screed bed in CM 1:6, complete all as specified and directed. |
| 36 | M&L for glazed coloured ceramic tiles of size 300mm x 200mm x 7mm/450X 300X 7 mm thick thickness in vertical surfaces over 10 mm thick rendering bed CM (1:4) layer set and jointed in neat cement slurry and pointed in coloured cement to match with the shade complete all as specified and directed. |
| 37 | M&L for machine cut Kota stone slab flooring 16-18 mm thick over cement screed bed laid and jointed with gray cement slurry mixed with pigment to match the shade of slab including and polishing complete over and including 15 mm screed in cement mortar 1 : 6 complete all as specified and directed. |
| 38 | M&L for machine cut Kota stone slab flooring 16-18 mm thick riser of step, skirting, dado and piller laid over and including 10 mm thick rendering in 1:4 on fair faces of brick work or concrete surfaces finishing rough for receiving wall tiles complete all as specified and directed. |
| 39 | M&L for Chequered cement concrete tiles 25x25x20-25mm / 30cmx30cmx20-25mm thick, with white cement and pigments set, jointed in neat cement slurry in floors laid over and including 15mm thick screed bed in cement mortar (1:6) complete all as specified & directed. |
| 40 | S&F PVC door frame of size 50mmx47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube fixing in opening as per specification & drawing complete all as specified and directed. |
| 41 | S&F factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed togehter with solvent cement, supplying & fixing in the frame at site as per specification complete all as specified and directed. |
| 42 | M & L for 2nd class hard wood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed. |
| 43 | S&F for 35mm thick 2nd class hard wood factory made plain framed, panelled shutter any number of panel with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically treated complete all as specified and directed. |
| 44 | S & F of 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. divided into squares, with out sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. and size of the members of shutter is as specified in clause No. 8.24 (a) of MES schedule 2009, part - I (Specifications) complete all as specified and directed. |
| 45 | S & F of 30mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. divided into squares, with out sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. and size of the members of shutter is as specified in clause No. 8.24 (a) of MES schedule 2009, part - I (Specifications) complete all as specified and directed. |
| 46 | S&F box type steel windows comprised of tubular frame and shutters made out of 1.25 mm thick MS tube factory made with double side shutters wire gauged shutters & glass glazed shutter(wire and glass panes shall be measured and paid separately) with side hung shutters with steel handles and steel peg stay doytaled at welded incl 2 Nos tower bolts 150 mm long for each leaf and 8 mm square bar grills at spacing as shown on drg welded to FI frame work,incl other fittings,hinges,handles tarred hold fast PCC blocks etc all as shown on drg No CEPZ/TD-354/09 sheet 1/3 to 3/3,complete all as specified and directed. |
| 47 | S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed. |
| 48 | S & F Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed. |
| 49 | S & F of 150 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed. |
| 50 | S & F of 100 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed. |
| 51 | S & F of 100 mm long mild steel butt hinges, medium weight cold rolled complete all as specified and directed. |
| 52 | S & F of 75 mm long mild steel butt hinges, medium weight cold rolled complete all as specified and directed. |
| 53 | S & F of 150 mm long extruded anodised aluminium alloy handle, fabricated type complete all as specified and directed. |
| 54 | S & F of 100 mm long extruded anodised aluminium alloy handle, fabricated type complete all as specified and directed. |
| 55 | S & F of 250 mm long (Length of bolt) aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolt of extruded sections or cast aluminium alloy complete all as specified and directed. |
| 56 | S & F of 0.50 mm thick pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet of any colour as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 57 | S & F of 0.50 mm thick pre-painted galvalume aluminium zinc coating GI based plain steel sheet of any colour as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 58 | S&F for 15 mm bore medium grade galvanized steel water tubing with all fittings and fixed to wall/ceiling or laid in floor complete all as specified and directed. |
| 59 | S&F for 20 mm bore medium grade galvanized steel water tubing with all fittings and fixed to wall/ceiling or laid in floor complete all as specified and directed. |
| 60 | Refixing old steel tubing 15 mm bore and connections in new or old position (walls/ceilings/floors etc) after cleaning complete all as specified and directed. |
| 61 | Refixing old steel tubing 20 mm bore and connections in new or old position (walls/ceilings/floors etc) after cleaning complete all as specified and directed. |
| 62 | S&F rotational moulded polyethylene three layered water storage tank 500 Ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position including PVC float ball valve 20mm dia with PTMT polythene float and fly nut, tank nipples with check nuts and washers complete all as specified and directed. |
| 63 | S&F in repairs float ball valve of 20mm bore high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed foriron pipe & fixed complete all as specified and directed. |
| 64 | S&F in replacement of steel rolling shutters of 1.25mm thickness of laths interlocked together and jointed with end locks without ball bearing incl guide channels, mild steel brackets, anchoring rod/pipe shaft with helical spring, pull handles, fixing bolts & nuts including hood cover, anchoring rod, hasp and staple with one shop coat of primer, erected in position as indicated, complete. Note :- Rate including greasing, change of rod, cover hood and other accessories as required as approved by GE. |
| 65 | S & F Safety lever locks mild steel with 4 levers for rolling shutters, complete all as specified and directed |
| 66 | S & F Ball bearing for rolling shutters, complete all as specified and directed |
| 67 | S&F mild steel as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting, welding or riveting etc. and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed. |
| 68 | S&F framed work such as grills, grating, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars, framed iron doors, ladders; framed balusters; walkways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165 complete all as specified as directed. |
| 69 | M&L mild steel framed work conforming to Fe-290 (Gde E-165), as in doors or gates of angle or other section with gusset plates, rails, braces etc. complete drilled for fixing steel sheeting or other covering to be prepare for hanging including either hooks or hinges etc complete all as specified and directed. |
| 70 | S & F mild steel columns, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. ade fe 269 W (Grade E-165) complete all as specified and directed. |
| 71 | S & F of flat iron bands, straps, supports, clamps, hold fasts, wall ties, wind ties, hooks for hanging fans and other similar small steel article confirming to Fe-290 Grade E-165 with and including necessary nut-bolts, washers, screws etc. as required complete all as specified and directed. |
| 72 | S&F welded steel wire fabric square/rect mesh n exc 4 kg per sqm complete to wood or steel members complete all as specified and directed. |
| 73 | S&F in repairs vitreous china squatting pan \\"ORISSA\\" pattern of size 580x440mm white, with integral foot rests with \\"P\\" or \\"S\\" of PVC(SWR) trap (excluding flushing cistern & flush pipe) incl provisioning of lime concrete bedding complete all as specified and directed. |
| 74 | S&F in repairs vitreous china urinals,flat back of size 465mmX355mmX265mm,white with grating and union for discharge pipe including connecting to waste pipe complete all as specified and directed. |
| 75 | S&F in repairs 10 ltrs capacity (PVC), valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle, including brackets, flush pipe, complete all as specified and directed. |
| 76 | S&F in repairs vitreous china ware wash hand basin white colour flat back of size 550x400mm including CI brackets, CP brass waste coupling 32mm etc complete all as specified and directed. |
| 77 | S&F in repairs CP brass towel rail 60cm long including fitting complete all as specified and directed. |
| 78 | S&F in repairs looking mirror of selected quality glass of area n.exc. 0.30 Sqm mounted on PVC frame fixed to wall surface with CP screws and rawl plugs complete all as specified and directed. |
| 79 | S&F in repair bib tap chromium plated cast copper alloy with capstan head wall flange screwed down screwed for iron pipe 15 mm bore complete all as specified and directed. |
| 80 | S&F 15 mm angle/stop valve cast (male or female thread) copper alloy chromium plated with capstan head, wall flange screwed down screwed for iron pipe and fixed in repairs complete all as specified and directed. |
| 81 | S&F in repairs 15 mm Pillar tap cast copper alloy in single lever with capsten head chromium plated screwed down high pressure with or without letter hot or cold with long screwed shank and flynuts screwed for iron pipe complete all as specified and directed. |
| 82 | S&F of PVC connection pipe 15 mm dia 450/600 mm long with PTMT nut fixed in repairs complete all as specified and directed. |
| 83 | S&F in repair PVC waste pipe suitable for 32 mm dia waste coupling for wash hand basin complete all as specified and directed. |
| 84 | S&F in repairs waste coupling of PTMT (half or full threaded) Minimum weight 32mm-45gms complete all as specified and directed. |
| 85 | S & F for PVC (SWR) soil, waste and vent pipes single socketed in any length with rubber rings joints fixed to walls or floor of 75mm bore with suitable MS clamps ind taking down old unserviceable pipe along with fittings any descriptions complete all as specified and as directed. |
| 86 | S&F in repair PVC (SWR) bends any radius suitable for 75mm bore pipe provided with access door complete all as specified and directed. |
| 87 | S&F in repair 75mm PVC (SWR), junction single, (Single T equal or unequal), fixed with solvent cement, with oval access door, complete all as specified and directed. |
| 88 | S&F in repair 75mm PVC(SWR) vent cowl. |
| 89 | S&F in repair 75 PVC (SWR) floor / nahani trap plain with ss grating, setting and jointing with solvent cement, complete all as specified and directed. |
| 90 | M&L for preparation of new wooden surfaces exc 10cm width or girth and applying two coats of synthetic enamel paint over one coat of primer complete all as specified and directed. |
| 91 | M&L preparing old wooden surfaces of any description exc 10cm width or girth and applying one coats of synthetic enamel paint complete all as spd and directed. |
| 92 | M&L applying two coats of synthetic enamel paint over a coat of red oxide including preparation of new steel or iron surfaces exc 10 cm width or girth, complete all as specified and directed. |
| 93 | M&L for applying one coat of synthetic enamel paint on old decorated steel surfaces exc 10 cm width or girth including preparation of surfaces, complete all as specified and directed. |
| 94 | M & L for preparing new ceilings surfaces and applying three coat of white wash on ceilings complete all as specified and directed |
| 95 | M & L for preparing old or previously treated ceilings surfaces by brooming down or with steel wire brushes, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of white wash on ceilings complete all as specified and directed. |
| 96 | M&L for applying two coats of oil emulsion distemper on newly plaster surface of walls (tint as approved by Engr-in-Charge) with sponge roller, including preparation of surfaces and priming with alkalie resistant priming paint on 1-2mm thick wall care putty complete all as specified and directed. |
| 97 | M&L for preparation of new surfaces of walls and applying Two or more coats (tint as approved by Engr-in-Charge) with sponge roller, 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre / 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre / 10 sqm over new surfaces incl exterior grade wall care putty 1-2mm etc., complete all as specified and directed. |
| 98 | M & L for preparing old or previously treated walls surfaces by brooming down or with steel wire brushes, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of oil bound distemper on walls with sponge roller complete all as specified and directed. |
| 99 | M&L for complete removal of existing treatment including washing, rubbing down and stopping of white wash / color wash/ cement base paint / synthetic enamel paint etc and preparation of surfaces of the same walls and applying Two or more coats (tint as approved by GE) with sponge roller, of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over surfaces incl exterior grade wall care putty where reqd 1-2mm upto three story building incl necessary scaffolding complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 02, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 23, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 11 daysJul 30, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 18 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender