Tender For Addition / Alteration To Joinery Work Alongwith Connected Works In Bldgs Nos P-1 To P-15 And P-26 To P-35 At Cgra Meenambakkam Under Ge (I) (Cg) Chennai.
Tender Value
37.80 Lakhs
Estimated cost
Bid Submission
23 Jul 2026
15 days left
EMD
75600
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Chennai → Tamil Nadu
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Addition / Alteration To Joinery Work Alongwith Connected Works In Bldgs Nos P-1 To P-15 And P-26 To P-35 At Cgra Meenambakkam Under Ge (I) (Cg) Chennai.
BOQ
| Sl. No. | Item Description |
| 1 | M&L for taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sq. m each complete all as specified and as directed. |
| 2 | M&L for taking down chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.5 sq. m but not exc 4 sq. m each complete all as specified and as directed. |
| 3 | M&L for taking down shutters of any description exc 1 sq. m and not exc 2 sq. m each complete all as specified and as directed. |
| 4 | M&L for resecuring or easing & adjusting shutters of any description exc 1 sq. m and not exc 2 sq. m each, without taking down shutters complete all as specified and as directed. |
| 5 | Supply and fix 2nd class hard wood, plain, solid, straight framed, in parts rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed. |
| 6 | M&L for Hold fast/clamps of mild steel stay for rain water pipes etc confirm to Fe-290 Gde E 165. |
| 7 | M&L for PCC Type 1:2:4 (12.5mm graded aggregate ) typeB0, PCC fliing cment concrete as in holdfast and mass concrete with WPC all as specified and directed |
| 8 | S & F second class hardwood 35mm thick Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats |
| 9 | 35mm thick 2nd class hard wood glazed and skelton shutter open rebated and prepared to receive glass ,gauge etc ( without sash bar) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc size of members of shutters as specified in SSR Part-I, section 8 clause 8.20(a), supplied and fitted to chowkats. |
| 10 | S & F in butt hinges mild steel cold rolled mild and fixed 100mm size, type C-22, extruded mild steel with mild steel hinge pin, anodised complete all as specified and as directed. |
| 11 | S & F 200mm aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed. |
| 12 | S&F 300mm long of alluminium sliding door bolt with hasp, staple (bolt type) with sand or die cast and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or brass door shutter complete all as specified and as directed. |
| 13 | S&F in 150mm length extruded alluminium alloy handles cast type , bright polished all as specified an directed by Engr In Charge |
| 14 | S & F floor door stopper of brass body and 140mm with hard drawn steel spring complete all as specified and as directed. |
| 15 | S & F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed. |
| 16 | S&F in Rolled sections as in DOOR FRAME OF ANGLE framing for cladding, glazing and the like fixed with angle cleats and connecting plates (Fe 410-W Gde E- 250, quality -A), etc.complete all as specified and as directed. |
| 17 | S&F, 19mm thick BWP Marine Plywood fixed to walls or BWP frame all as specified and as directed. |
| 18 | S&F, 0.8mm thick laminated sheet of approved colour with necessry fixing complete all as specified and as directed. |
| 19 | S&F,125 mm stainless steel Handles with necessary fixing accessories complete |
| 20 | S&F continous (Piano) hinges of mild steel bright finish or elctrogalvanised 30mm flap width all as specified and directed by Engr In Charg |
| 21 | S & F 150mm SS tower bolts of fixed complete all as specified and as directed. |
| 22 | S & F wardrobe hooks (single) 50mm to 60mm, aluminium, complete all as specified and as directed. |
| 23 | S & F for MAGNETIC CATCHER complete all as specified and as directed. |
| 24 | M&L for preparing of New or previously painted wooden surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over one coat of primer complete all as specified and as directed. |
| 25 | S & F solid PVC door frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet & edges will be painted to match with prelam sheet, reinforced with M.S. square tube and fixing in opening as per specification & drawing complete all as specified and as directed. |
| 26 | S & F Factory made solid panel pvc door shutter 30 mm thick (style) consisting of frame made out of M. S. tubes for top & bottom rails. M. S. frame shall be covered with heat moulded plain colour PVC `C` channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M. S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and as directed. |
| 27 | Material and labour for providing water proofing treatment to Bath rooms and Toilets by chipping out tiles/loose particles of floor and alround on walls to a height of 60cm (2 feet) until to reach sound surface, repair all cracks by cutting “V” groove, remove all debris, dirt, oil, grease and foreign matter by jet of dry air and fill with polymer modified crack filling compound/crack sealer by using proper mechanical tools, treating the hunch surfaces, Walls and floor joints with 100mm x 100mm coving and laying polymer modified cement mortar/ concrete in the ratio 1:1.5:3 mixed with water proofing admixtures and apply a first coat of two-component, UV resistant, acrylic polymer modified cementitious elastomeric waterproofing coating @ 500gms/Sqm, when the surface of first coat is still tacky spread Fibre glass tissue/scrimp of 45-50GSM with overlaps of 50mm on both directions and allow it to dry for 10-12 hours and apply a second coat of UV resistant, acrylic polymer modified cementitious elastomeric waterproofing coating @ 500gms/Sqm perpendicular to the first coat for cross linkage for a total DFT of 1500 microns and finished with the protection layer of Polymer modified cement mortar plastering in the raio of 1:3 mixed with water proofing admixtures and fixing the new floor and wall tiles of same make & shade and of size matching to the existing tiles with tile adhesive and pointed with tile grout complete all as per manufacturer's instruction and as directed.Note : (i) CP fittings, Soil & Waste pipes, Water supply pipe lines got damaged while doing WPT work shall be replaced and made good by the contractor without any extra cost.(ii) The unit rate quoted shall be deemed to include the cost of above provisions including fixing of Non skid ceramic coloured floor tiles and glazed ceramic wall tiles with tile adhesive as per manufacturer's instructions. |
| 28 | Material and labour for cutting grooves in tile joints to 3mm width and 5mm depth, cleaning and remove all debris, dirt, oil, grease and foreign matter by jet of dry air, apply epoxy tile grout of ShaliTile- Grout E of STP limited or equivalent of other specified makes with proper mixing of resin, hardner and powder to joints of tiles in floors of Bathroom / WC Toilet rooms of area not exc.5 Sqm each by using proper tools complete all as per manufacturer's instructions and as directed. |
| 29 | Material and labour for PU Injection groutings by Drilling 10mm dia hole, depth suitable to the concrete thickness, fixing injection Ports and tighten non - shrink materials by using proper tools and application of ShaliGrout PU 2K 20 PU Injection Grout or equivalent of other specified makes to arrest the leakage stage by stage using mechanical tools and electrical operated Resin grout Pump complete all as per manufacturer's instruction and as directed. |
| 30 | Material and Labour for providing water proofing treatment to sunshades by cleaning the top surfaces of sunshades/chajjas/floor with wire brush and washing with hydrochloric acid to remove all loose gravel, dirt, oil, grease, loose particles, foreign materials etc., by jet of dry air and clean the surface mechanically or by grinding to make it smooth, repair all cracks by cutting “V” groove and fill with polymer modified crack filling compound/crack sealer by using proper mechanical tools, treating the hunch surfaces, Walls and floor joints with 100mm x 100mm coving and laying polymer modified cement mortar/ concrete in the ratio 1:1.5:3 mixed with water proofing admixtures and apply a first coat of two-component, UV resistant, acrylic polymer modified cementitious elastomeric waterproofing coating Shali Urethane BTD of STP limited or equivalent of other specified makes @ 500gms/Sqm, when the surface of first coat is still tacky spread Fibre glass tissue/scrimp of 45-50GSM with overlaps of 50mm on both directions and allow it to dry for 10-12 hours and apply a second coat of UV resistant, acrylic polymer modified cementitious elastomeric waterproofing coating @ 500gms/Sqm perpendicular to the first coat for cross linkage for a total DFT of 1500 micron complete all as per manufacturer's instruction and as directed.Note : The unit rate quoted shall be deemed to include the cost of necessary scaffolding and other safety measures works. |
| 31 | Material and labour for providing treatment to core cutting area of pipes in WC, bathroom/Toilet, RWP in roof slab and similar by grinding the core pipe surrounding areas and around the pipe in square size to reach up to maximum of 3 inches depth inside the wall/floor, clean and remove all loose mortar and dust particles and apply first level packing with Non-Shrink Fast Setting Hydraulic Cementitious product ShaliMar Dam-IT or equivalnet of other specified make plug mortar in the ratio of 1:3 with adding admixtures over a coat of bonding agent to plug the prepared crack with a pointing trowel and slick off the surface and apply ShaliGrout HS packing surrounding area of pipe to achieve the desired consistency for proper finishing complete all as per manufacturer's instruction and as directed.Note : The unit rate quoted shall be deemed to include the cost of scaffolding and other safety measures works. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 02, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 23, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 15 daysJul 25, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 17 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender