Tender For Pipeline Rehabilitation Works On 3200 Mm Dia Rc Pipeline Using Chemical Compounds On Targeted Location Between Chainages 13.50 Km To Teela Morh Under 270 Cusec Delhi Water Supply Maintenanace Scheme
Tender Value
31.04 Lakhs
Estimated cost
Bid Submission
18 Jul 2026
3 days left
EMD
62000
Bank guarantee accepted
Document Fee
3540
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Salarpur → Uttar Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Pipeline Rehabilitation Works On 3200 Mm Dia Rc Pipeline Using Chemical Compounds On Targeted Location Between Chainages 13.50 Km To Teela Morh Under 270 Cusec Delhi Water Supply Maintenanace Scheme
BOQ
| Sl. No. | Item Description |
| 1 | Treatment of Joints |
| 2 | Dewatering from ditches, pits and trenches around 3200 mm Dia RC pipeline including hiring of pump set of. diesel operator etc. complete & suction pipe & delivery etc. complete. |
| 3 | Cleaning of Joints including removing of baker rod if any), filling and all other loose materials from the expansion joint and clean the surface around the joint to make it free from loose particles, dirt oil, grease etc and disposal of malba debris outside of pipeline including all labour T&P etc complete |
| 4 | Drilling and fixing injection packers in RC members including, Drilling Holes: Drilling holes in structural members at intervals as per the recommendation of the engineer in charge. Cleaning of holes: Clean the holes with air blower before fixing nozzles. Fixing of Packers: Insert 12 mm dia., 50~75 mm long injection packers in cleaned holes with moisture-insensitive epoxy resin-based putty or equivalent. Cutting of Packers: Cut the Packers by wheel after grouting completion without damaging structural elements. Patching Hole:- After cutting off the packer we patch the hole on epoxy putty |
| 5 | Supply and application of single component, Polyurethane Injection foam based system for wet conditions and temporary sealing, which cures to a dense flexible foam with a fine cellular structure. Minimum Product Requirements: Viscosity cps 500-1300 at 23°C |
| 6 | Supply and application of 2 components, elastic, low viscous, solvent-free, Polyurethane Injection resin based system for permanent sealing, that does not need the presence of water for hardening reactionProduct Requirements:The viscosity of the mixture < 100 mPa*s (at +20°C) Capable of penetrating cracks>0.2mm wide with a CE Marking (European Conformity) -> Conformance label that the product is approved to the essential requirements and under market surveillance |
| 7 | Epoxy Grouting Fosroc (EP10) sealing of crack/porous concrete in Reinforced Cement Concrete Structure by injection process through nipples grouting complete as per Technical Specifications. |
| 8 | Repairing the edges of the joint (in case of weak concrete at the joint edge) and also configuring the joint width (in case of expansion joints with irregular width more than the width of the chosen Sikadur Combiflex Tape width) with epoxy repair mortar Sikadur 31 and Sikadur 41/ Sika Latex or its equivalent. |
| 9 | Filling the joints with Rubber compression seal for expansion joints of size next higher to the joint gap and apply Polysulphide sealant in the expension joint up to a depth equal to not less than 1/2 the width of the joint including insert bitumen impregnated board as filling material,T&P etc. complete. |
| 10 | Providing and applying the base coat of epoxy adhesive on both sides of the joint as per the width of the Sikadur Combiflex SG Tape.Product: Sikadur-Combiflex® Adhesive or its equivalentConsumption: 1.4 kg/m (strip width 200 mm)Product requirements: mixed density: 1.60kg/ltr; bond strength > 2 N/mm2. |
| 11 | Providing and applying flexible FPO based tape 200 mm x 2mm as per manufacturers’ method statement ( for 50 to 100 mm or lower joint size)Similar Product Make : Sikadur®-Combiflex® SG System or its equivalentProduct requirements: Chemical Base Modified flexible Polyolefin (FPO) with advanced adhesion Fire Rating Euroclass E (EN ISO 11925-2, classification to EN 13501-1)Service Temperature -30°C min. to +40°C max. in wet conditions -30°C min. to +60°C max. in dry conditions Mechanical / Physical Properties Tensile Strength > 12 N/mm2 (EN 12311-2) Tear Strength > 40 N/mm (ISO 34-B) Elongation at Break > 600 % (EN 12311-2) Seam strength > 300 N/5cm (2 mm) (EN 12316-2) > 400 N/5cm (2 mm) (EN 12317-2) Behaviour under hydrostatic pressure6bar/72h No leakage (EN 1928-B) Resistance: Chemical Resistance Please consult the Sikadur-Combiflex SG system or its equivalent product data sheet. Thermal Resistance Thermal ageing:Passed (SIA V280, 1996) Bonding test: No cracks at -40°C (EN 495-5) Artificial weathering:7500 h passed (SIA V280, 1996) |
| 12 | Providing and applying epoxy adhesive coat over the water proofing tape on either side of the joint, covering the sheet at the top and extending 5mm beyond the edges over the lower layer of adhesive and finishing the top layer of adhesive by tapering the edges comletely sandwiching the joint sealing tape.Product: Sikadur-Combiflex® Adhesive or its equivalentConsumption: 1.4 kg/m (strip width 200 mm)Product requirements: mixed density: 1.60 kg/ltr; bond strength > 2 N/mm2. |
| 13 | Labour cess@1% Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 02, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 18, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 3 daysJul 18, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 3 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender