Tender For Repairing Of Tube Well At Jj Cluster, Holambi Ac 01.
Tender Value
Ref. Documents
Estimated cost
Bid Submission
08 Jul 2026
2 days left
EMD
6000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Delhi → Delhi
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Repairing Of Tube Well At Jj Cluster, Holambi Ac 01.
BOQ
| Sl. No. | Item Description |
| 1 | Lifting of p/set by the help of chain pully, clamps and heavy menpower after cuting rusted/wornout and opening of nut bolts to dismental the p/set, pipes etc. |
| 2 | S/o submersible cable with copper conductor having three core sizes 6 sq. mm working on 1100V. Make:-Finolex/Plaza/Unistar or any other make approved by DJB. |
| 3 | Making and supply of MS clamp of 400 mm long x 70 mm width x 10 mm thick complete with nut and bolts and washers for holding the 50 mm dia pipe including bending and shaping etc. as required. |
| 4 | S/o G.I bend 50 mm dia 90deg. Double flange. Heavy class Make: - Ganesh/ ISI |
| 5 | S/o of 3 mtr. GI pipe 50 mm dia size ,medium class with GI flange welded in both sides 3 Mtr long with ms strips complete with threading work on each side of pipe each flange should be 4 nos of holes and cut for cables. Make :- Jindal / TATA. |
| 6 | CI double flanged swing type non return valve as per IS:5312 PN 1.0 CI body door / bronze to rubber ring / SS 410 twin pin, 50 mm dia. Make - Kirlosker/IVC/any approved make. |
| 7 | C.I. double flanged non-rising spindle sluice valve P.N 1.0 IS:14 sub, CI body / wedge / bronze ring / S.S 410 shaft construction & S.S. IS: 6603 Gr. 12 CR 12 CISI marked manual operation. 50 mm dia handwheel Make - Kirlosker/IVC/any approved make. |
| 8 | S/o G.I required off size threaded heavy duty nut-bolts of good quality. |
| 9 | Supply of MS bore cover 4 mm thick suitable for bore size in 2 pieces complete with bolting arrangement angle iron frame and provision of 50 mm dia hole in the center. |
| 10 | S/o pressure gauge of 100 mm dia, 0-30 PSI complete with socket, bush Make:-H-Guru/Fiebig |
| 11 | Making water sample point with the help of socket, niple, cook valve, Tee and extended pipe etc. of size 1/2 inch. |
| 12 | Making and Supply of G.I tail piece of 50 mm dia. , one mtr. Long size made out of medium class pipe complete with one end threaded and other end fitted with G.I. flange heavy and cut for submersible cable. Mak of Pipe - Jindal/Tata. |
| 13 | upply of Starter panel board suitable upto 12.5 HP Submersible Pump Set having following specifications :-1. Three phase, Star Delta Motor Control Panel, 415 VAC 50 HZ.2. Digital controlling of parameters i.e Ampere and voltage.3. PMC Based DC operated 40 Amp. power contact. 4. Digital Display for Parameters i.e Ampere and voltage & Motor Run Hour.5. Automatically over load cut off.6. Under voltage/over voltage automatically cut off.7. Single phase and reverse phase protection.8. Auto/manual mode selector switch.9. MCB/MCCB- 40 AMP at incomer to interrupt the supply in faulty condition.10. Programmable Timer, 220 volt AC for auto start and stop.11. Run hour meter to show the total time of run.12. IP 54 Protection.13. Box size – 350 x 500x 150 approx. Make - ISI/Any approved make. |
| 14 | Supply of neoprene rubber sheet having 50% neoprene, 3 mm thick. Make - Jyoti/Worth/DJB approved. |
| 15 | Supply of electric insulated sheet for AC & DC which is moisture proof, U.V. protected, fire retardant, high di-electric strength, easy to clean, auto glow path, coloured strips on both sides, glow in emergency, CPRI approved, confirming to BISDOC No. ET-02 (5440). Dt: 30-04-04, meeting requirement of IS:3043, IS:5216 (Part 1,2 & 3), IS: 8437 and IEC: 479 PUB-1 tested for breakdown strength tensile, elongation aging properties, insulation resistance effect of acid, alkaline, diesel and transformer oil, leakage current test etc. 1 no. = 1mtr. breadth x 2 mtr. length. Make: Electromat/Safevolt |
| 16 | Installation of all E&M Equipments, lowering pump set into the bore all piping work fixing of valves and accessories executing minor civil works, making electrical connections with cable as required size by the help chain pulley to lower pump sets testing and commissioning of all E&M equipments at no load and full load conditions as per standard from full satisfaction of Engineer-in-Charge. The job also includes the transportation charges, providing/fixing of required gap piece, for fixing valves, pressure gauge with the help of welding machine etc. and proper electric connections. Note - Repaired submersible p/set will be provided by the departmently ; if required. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 02, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 08, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 2 daysJul 08, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 2 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender