Tender For Special Repair To Bldg No P-61 & P-62 (Single Junior Commissioned Officer Accommodation) And Bldg No T-167 (Ancyillary Section Complex) At Nabha Under Ge (South) Patiala
Tender Value
Ref. Documents
Estimated cost
Bid Submission
23 Jul 2026
17 days left
EMD
97100
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Patiala → Punjab
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Bldg No P-61 & P-62 (Single Junior Commissioned Officer Accommodation) And Bldg No T-167 (Ancyillary Section Complex) At Nabha Under Ge (South) Patiala
BOQ
| Sl. No. | Item Description |
| 1 | 'Notes: (i) Please refer Schedule 'A' Notes of tender documents. |
| 2 | Taking down cement or cement lime plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed. |
| 3 | M&L for 15mm thick cement pastering in cement mortar 1:4 and mixig the water proofing compound as per manufactures instructions on brick or concrete surface of wall finished complete all as specified and directedNote: Water proofing compound shall be measured and paid saparately under item. |
| 4 | M&L 10mm thick cement plastering in cement mortar CM 1:6 finishing the surface even and smooth without using extra cement, complete all as specified and directed. |
| 5 | Complete removal of existing treatment of any type/description such as distempering work ,internal emulsion etc from internal/external surfaces of walls & ceiling with mechanical means/grinder including removal of material from site complete all as specified and directed. |
| 6 | Material and Labour for exterior painting work including complete removal of existing loose paint layers till plaster level by using jet pressure washer and crack filling up to 3mm by using crack seal & up to 10mm by using textured crack filler. Touch-up by using wall putty with silicon additives followed by application of one coat of truecare exterior primer on walls and Chajjas and applying two coats of modified acrylic smooth emulsion exterior grade with silicon having anti-algal and Dust pickup resistance properties, Material should be applied (Dilution, Recoating period etc..) as per manufacturer instructions by using fully automatic air less spray machine having flow speed of minimum 1ltr per minute and pressure of 3300 PSI, complete all as specified and directed.Note- (i) The contractor shall submit manufacturer generated 04 years warranty card for each buildings treated/ painted during submission of Final Bill and guarantee amount @ 5% will be kept as reserve till completion of warranty period and will be released thereafter. Any deterioration during the warranty period will be rectified by the contractor without any financial effect within a week.(ii) The work shall be executed by the contractor as per MoU from authorised applicator through manufacturer of the materials like Exterior/Interior Paint, Putty etc after approval by the GE.(iii) The Contractor shall upload with the documents under cover I \\"Memoradum of Understanding\\" (MOU) as per format given in Annexure ‘A’ after Schedule 'A' Notes with at least one of the manufacturers mentioned in the contract, failing which the bid shall be laible to be rejected.(iv) Cost of T&P and a scaffolding/Jhoola, trestles, ladders, cradeles, centring, crane, boom lifts/ crane of any type and shuttering etc necessary for execution of work and protective measures complete upto all height shall be deemed to be included under respective item.(v) Cost of temporary covering to all joinery items (like doors, windows, window panes), sanitary fittings, dado/skirting, floors, etc to protect them from splashes.(vi) Packing material/empty Buckets will not be handed over to the contractor and will be property of the MES and will be disposed off with the permission of the Engineer-in-Charge and GE. |
| 7 | (vii) Washing floors, cleaning glass, joinery , electric fittings , wirings etc. Drops and splashes of paint to be cleaned to the entire satisfaction of Engineer-in-Charge.(viii) Sample patch of 10Sqm be prepared and shall be got approved from GE prior to carrying out further work.(ix) Cost of removing of nails, making good holes, filling of cracks with acrylic crack filler paste etc shall be deemed to be included under respective item.(x) Work in patches and in narrow / widths, bands, cornices, pilasters etc and cutting in edge of line where necessary. |
| 8 | M&L prepration of new plastered or unplastered surface of walls and applying two coats of distemper oil emultion over complete all as specified and directed |
| 9 | Supplying & applying for two component elastomeric acrylic polymer modified cementitious waterproofing coating on Brick level, SmartCare Damp Block 2K or approved equivalent, having 100% elongation as per ASTM D412, resisting 5 bars hydrostatic pressure as per DIN 1048, reduction to rapid chloride shall be 70 as per ASTMC1202, crack bridging up to 1.2mm as per ASTM 4548.5. The coating shall have food grade certificate from laboratories like CFTRI, will be apply on both Positive & Negative side and resist up to 5 Bars of Hydrostatic Pressure. The mixing ratio of the coating shall be 2 parts of powder & 1 part of liquid without any water addition in the mixing, etc. After coating will sprinkle Sand on the coating which is in contractor scope, complete as manufacturer specifications and as specified and directed.Note - Taking down plaster and rendering will be measured and paid seprately |
| 10 | Supply only integral water proofing compound ISI marked complete all as specified and directed. |
| 11 | M&L for rendering 5mm thick in cement mortar 1:3 as on concrete surfaces in ceiling finished even and smooth without using extra cement, complete all as specified and directed. |
| 12 | M&L for preparation of new plastered or unplastered surfaces applying three coat of white wash on ceiling surfaces complete all as specified and directed. |
| 13 | M&L for preparing old plastered surfaces of ceilings and applying one coat of white wash complete all as specified and directed. |
| 14 | Taking down chowkhats or frames (without taking off shutters from the frame) exc 1.5 Sqm and n. exc 4.00 Sqm incl cutting holes and making good reqd shape for hold fast block for new frame complete all as specified and directed. |
| 15 | All as per srl item No 13 hereinbefore but n. exc 1.5 sqm each complete all as specified and directed. |
| 16 | S&F Powder coated Pressed steel frames made of MS sheet of 1.25 mm thickness for doors with single rebate including necessary fixing lugs,hinges, lock strike plate, hold fasts , PCC 1:2:4 B1 hold fast blocks etc., complete as specified,size 105x 60mm including cutting holes and making good reqd to shape for hold fast blocks for new frame complete all as specified and directed. |
| 17 | S&F Powder coated Pressed steel frames made of MS sheet of 1.25 mm thickness for doors with double rebate including necessary fixing lugs,hinges lock strike plate, hold fasts , PCC 1:2:4 B1 hold fast blocks etc., complete as specified,size 125x 60mm including cutting holes and making good reqd to shape for hold fast blocks for new frame complete all as specified and directed. |
| 18 | M&L Plain cement concrete (1:3:6) type C-0,using 12.5 mm graded mechanically crushed stone aggregate as in back filling of pressed steel frame /hold fast blocks etc and similar complete all as specified and directed. |
| 19 | S&F 35mm thick plain framed (Factory made) Panelled shutters of 2nd class HW without lock rail and panels of 9mm B.W.P commercial ply including beading on the facing side of shutters as per SSR Part I clause No 8.17.5. The size of rail and stiles as per IS 1003 (Part I) kiln seasoned and chemically pressure treated complete all as specified and directed. |
| 20 | S&F 35mm 2nd class hard wood Glazed and skeleton shutters, 2nd class hard wood open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed. |
| 21 | S&F aluminium 200mm anodised , barrel tower bolt of extruded complete all as specified and directed |
| 22 | S&F aluminium anodised sliding door bolt of size 250mm, stove enamelled black with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts complete all as specified and as directed. |
| 23 | S&F aluminium handles 125mm cast type, anodised complete all as specified |
| 24 | S&F Mild steel butt hinges of size 100mm medium weight cold rolled complete all as specified and directed. |
| 25 | S&F in repair 300 mm long MS rat tail pattern spring hinge including roller and roller plate, complete all as specified and directed. |
| 26 | S&F Floor door stopper of aluminum alloy body and tongue, anodised, with hard drawn steel spring fixed complete all as specified and as directed. |
| 27 | S&F Factory made steel windows box type using ERW hollow 'P' section comprising double frame for glaged and gauged skelton shutters jointed interally with flat iron 40x4mm complete including grill of 8mm square bar, fixed horrizontally @ 10cm centre to centre, hinges,handle tower bolts,lugs etc all as shown on drawing noTD-219(c) sheet 1/3 to 3/3 and TD-220 (c) sheet 1/3 to 3/3 as applicable and complete all as specified and directed.Note;- (i)for the purpose of measurement& payment double shuttre with frame shall be considered as one unit.(ii) Wire mesh and glass, measured and paid for separately. |
| 28 | S&F in repair Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directied |
| 29 | M&L for preparing of new surface of wood and wood based material of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel pain and one coat of pink primer all as specified and directed. |
| 30 | M&L for preparing surfaces of any description over 10 cm girth or width, not otherwise described and applying two coats of synthetic enamel paint over a coat of Red oxide on new surfaces of steel or iron, complete all as specified and directed. |
| 31 | Demolition of cement concrete (un-reinforced) in ground floors and pavings n exc 15cm thickness (below or above ground level), complete all as specified and directed. |
| 32 | Dismantling of floor or wall tiling including cement mortar bedding but not backing and removing the rubbish off the premises complete all as specified and directed. |
| 33 | M&L 25mm thick PCC (1:2:4) type B-0 using 12.50 mm graded crushed stone aggregates in floor base complete all as specified and directed. |
| 34 | M&L for ceramic floor tiles of 7 to 8mm thick of Size 600 X 600 mm in floor etc set and jointed in neat cement lurry and pointed in white cement to match over and including 15mm thick screed bed in CM (1:4) laid in complete all as specified and directed. |
| 35 | M&L for Non Skid coloured tiles 7 to 8mm thick and Size 400 X 400 mm in flooring etc set and jointed in neat cement lurry and pointed in white cement to match over and including 15mm thick screed bed in CM (1:4) laid in complete all as specified and directed. |
| 36 | M&L for coloured glazed ceramic tiles 7 to 8 mm thick of Size 600 X 300 mm as in vertical surfaces such as skirtings, dados etc jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 10mm thick back coat in CM (1:4), in complete all as specified and directed. |
| 37 | Taking Up or down steel tubing of size 15mm bore and removal to store complete all as specified and directed |
| 38 | Taking Up or down steel tubing of size 20mm bore and removal to store complete all as specified and directed. |
| 39 | Supply and laying of 20mm outer dia CPVC pipes SDR11 & plain CPVC SDR 11 fitting fixed on wall / celling or laying in floor complete all as specified and as directed |
| 40 | Supply and laying of 25mm outer dia CPVC pipes SDR11 & plain CPVC SDR 11 fitting fixed on wall / celling or laying in floor complete all as specified and as directed. |
| 41 | S&F in repair mild steel chromium plated 20mm curtain rod harrison rails with fixing brackets, stops rollerss complete incl fixing brackets, stops etc complete all as specified and as directed.Note: For the purpose of mesurement and payment running length of curtain rod only shall be considered. |
| 42 | S&F 18 mm thick LEAD FREE PVC celuka ply of approved color fixed with screws, slovent cement/adhesive to make kitchen/bed rooms cabinet sides top and bottom and shelves inside the cabinets complete as per manufactured's specification complete all as specified and directed.Note: not less than 10kg per sqm |
| 43 | S&F Paino/continuous hinge of size 30 mm stainless steel complete all as specified and directed. |
| 44 | S&F ball catchers 304 grade stainless steel finished suitable for cabinets premium quality complete fixed in position as per manufacture's instructions complete all as specified and as directed. |
| 45 | S&F D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished 150 mm long matt finished complete fixed in position complete all as specified and as directed. |
| 46 | Dismantling of brick tiles or terracing tiles single layar on roofs complete all as specified and as directed. |
| 47 | Taking out old damaged tar felt of any description from roof tops including cleaning, washing and drying the surface before applying roof treatmentcomplete all as specified and as directed. |
| 48 | Demolation of mud puska and removing on roof any thickness complete all as specified and as directed. |
| 49 | M&L for PCC 1:2:4, type B-0 using 12.5 mm graded stone aggregates as in padding over roof a slope of 1:100 using water proofing compound finish even and smooth without using extra cement complete all as specified and as directed. |
| 50 | M&L for the following roof treatment.(a) Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3mm thick weight not less than 3kg/Sqm water proofing membrane, black finished reinforced with non woven polyester matt, fixed as per manufacturer’s instructions complete all as specified and directed.(b) Applying one coat of aluminium paint over APP membrane @ 0.50 litres per Sqm all as specified and directed. (c) Applying evenly a tack coat of industrial bitumen 85/25 @ 1.2 kg per square metre including cleaning the surfaces complete all as specified and as directed. |
| 51 | M&L for plain cement concrete tiles with grey cement and pigment 20cmX 20cmX25mm thick, machine pressed; set jointed and pointed in neat cement slurry in floors, over 15 mm thick cement screed bedding layer in cement mortar 1:6, complete all as specified and as directed. |
| 52 | S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame atsite as per specification & drawing |
| 53 | S&F Solid PVC door frame of size 50 mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, fixed in opening as per specification and drawing, complete all as specified and as directed. |
| 54 | S&F for PVC(SWR) Floor trap 75mm plain with CP grating including jointing to wate pipe with solvent cement complete all as specified and directed. |
| 55 | S&F for PVC ( SWR) rain water pipes 110 mm bore single socketed in any length with rubber ring joints fixed to walls complete as as pecified including flat iror clamps 25x3mm complete all as specified and as directed including taking out old damaged AC rain water pipes. |
| 56 | S&F for PVC (SWR) bends of any radius for 110 mmdia rain water pipes with rubber ring joints a complete all as specified and as directed. |
| 57 | S&F in repair Rotational moulded polythene water storage tank cylindrical vertical with closed top 500ltr capacity hoisted and fixed in position incl 20 mm bore ball brass valves high pressure with polythene float and fly nut complete all as specified and as directed, including dismantalling of old PVC tank |
| 58 | S&F 125mm Brass chromium plated shower rose complete all as specified and directed. |
| 59 | S&F in Repair Bib taps( Long Nose) for 15 mm dia bore pipe cast copper alloy cromium plated with capstain head screwed down for iron pipe or brass ferrule and fixed complete all as specified and as directed. |
| 60 | S&F in repair Pillar taps Cast copper alloy fancy type 15mm bore, with capstan heads Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed with long screwed shanks and fly nuts scrrewed for iron pipe complete all as specified and as directed. |
| 61 | S&F in Repair Angle stop valve (Concealed type) cast copper alloy chromium plated with capstan head , long shank and cup screwed down screwed for iron pipe or for brass ferrule for 15 mm bore pipeafter taking down old stop cock of any description complete all as specified and as directed. |
| 62 | S&F in Repair 20mm Stop valves/ gate valve, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. |
| 63 | S&F in Repair 450 mm long PVC connection with brass nuts on both ends for 15mm bore pipes of approved quality complete all as specified and directed |
| 64 | S&F viterous china, wash hand basin, white, flat back, size 550x400mm including PVC waste pipe 32mm bore and mild steel brackets, fixed all in repairs, including cutting for or pinning in brackets complete all as specified and directed |
| 65 | S&F 600mm x 450mm mirror of selected quality glass mounted on 6mm thick AC building board with alluminium frame all around hanging to wall with rawal plug and iron slits cup washers complete all as specified and as directed. |
| 66 | S&F Tubular towel rail, CP 20mm dia, 60cm long between flanges fixed in repairs complete all as specified and as directed. |
| 67 | Supply & fixing low level flushing cistern of PVC 10 ltr capicity incl 45cm long PVC connection with brass nut at both ends, 15 dia stop cock cast copper alloy,screwed both ends , high pressure(wt not less than as specified in SSR), PVC flush pipe 32 mm bore complete all as specified and directed. |
| 68 | S&F viterous china ware wash down water closet Orrisa pattern size 580x440mm white with integral foot rests including connection to traps and to flushing pipe, anti syphonage pipe complete fixed in repair, complete all as specified and as directed. |
| 69 | S&F Vitreous China wash down water closet pan (Pedestal Pattern), white including white plastic seat cover with mild steel CP hinging device, suitable brass CP wash jet, complete jointing, connecting and making good the disturbed complete all as specified and directed. |
| 70 | M&L for Hard core of broken stone boulders of gauge 40 mm spread and levelled in layers n exc.15cm thick, watered and rammed to a true surface complete all as specified and as directed. |
| 71 | M&L for PCC (1:3:6), 50mm thick aggregate size 40mm as in PCC path/ plinth protection.finished the surfaces even and smooth with out using extra cement complete all as specified and as directed. |
| 72 | M&L for Machine cut Kota stone slab flooring 20mm (+2mm) thick laid over and including 15 mm thick screed bed or bedding layer in cement mortar 1:4 as base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. |
| 73 | All as per item No 71 here in before on vertical surfaces as in skirting /dado of size as required at site complete all as specified and as directed. |
| 74 | S&F for PVC enclosed case (cabin type) with cover and looking mirror over it with two shelves in it and fixed with screws on wall, complete all as specified and as directed. |
| 75 | S&F PVC (SWR) Sewage pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors of 110 mm bore complete all as specified and as directed. |
| 76 | S&F PVC (SWR) Sewage pipes single socketed, in any length with rubber ring joints, fixed to wall of 110 mm bore complete all as specified and as directed. |
| 77 | S&F PVC (SWR) 110mm bore Bend complete all as specified and as directed. |
| 78 | S&F PVC (SWR) 110 mm vent cowl complete all as specified and as directed. |
| 79 | S&F in repair PVC (SWR) junction double, (double T), equal or unequa 110 mm with parallel branch complete all as specified and as directed. |
| 80 | Demolition of brick work or stone masonry built in cement mortar including all quions, arches, pillers, etc complete all as specified and as directed. |
| 81 | M&L for brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in in cm 1:6 with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius complete all as specified and as directed. |
| 82 | S&F Fe-410 (Gde E-250) Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening complete all as specified and as directed.Note - Removing of old gate fixing new steel gate of hold fast , finish the surface included in this item. |
| 83 | M&L for 110 mm bore, cement concrete bed 1:3:6 type C2, using 40mm graded stone aggregate to drain pipes including packing under and haunching against the sides of pipes after they are laid and fitted, complete all as specified and as directed. |
| 84 | M&L for applying acrylic thick wall care putty on internal/external surfaces of walls/ceilings/soffits(thickness vary from1.5to2.5mm as required for desired smoothness and levelling of surfaces in two or more layers)by us ingready made wall careputty including sand papering after filling the putty to make surface smooth and ready for receiving painting etc complete all as specified and directed. |
| 85 | Demolition of reinforced cement concrete of any description (Reinforecement cut as required to facilitate demolition ) complete all as specified and as directed. |
| 86 | M&L for reinforcement cement concrete (Normal mix )1:2:4 Type B1 (20mm graded aggregate) as in slab support on wall , beams and collums in floor roof landing balconies deck slab and in shelves and the like, complete all as specified and as directed. |
| 87 | M&L for Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and as directed. |
| 88 | Use & waste of formwork to sides and soffits of floor and roof beams ,lintels beam ,cantilevers ,shelves including supports ,overhangs and similar work , for rough finished flat surfaces complete all as specified and as directed. |
| 89 | S&F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides kiln seasoned and chemically pressure treated complete all as specified and as directed. |
| 90 | S&F mild steel barrel tower bolt 200mm long stove enamelled black with bright bolt and fixed, complete all as specified and as directed. |
| 91 | S&F mild steel sliding door bolt of size 250mm , stove enamelled black with bright bolt not less than 12 mm dia, with and including a minimum of 6 bolts and nuts, complete all as specified and directed. |
| 92 | S&F MS pressed handles of size 125mm oval type stove enamelled black, complete all as specified and as directed. |
| 93 | S&F sheet glass ordinary quality 4 mm thick and glazing with oil puttly or wooden beads in square not exceeding 0.5 sqm in each pane complete all as specified and directed. |
| 94 | M&L for preparing surfaces of any description over 10 cm girth or width, not otherwise described and applying two coats of synthetic enamel paint over a coat of Red oxide on new surfaces of steel or iron, complete all as specified and directed. |
| 95 | Dismantling of asbestos cement sheets [corrugated, semi-corrugated, etc] in roof coverings complete all as specified and directed |
| 96 | S&F for pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/clading to wall, fixed to self tapping screws complete all as specified and directed. |
| 97 | S&F pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in ridges, roof covering/clading to wall, fixed with self tapping screws complete all as specified and directed. |
| 98 | Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed. |
| 99 | M&L anodised aluminium snap grid false ceiling of grid size 605x605mm consisting of aluminium main and \\"T' sections of size 25x35x1.5mm thick and wall angles of size 25x 25x 1.5 mm thick suspended with GI wire suspenders of 6mm dia of suitable length and 8-10 mm thick gypsum board, 60x60 cm size fixed with staples on snap grid complete all as specified and directed. |
| 100 | S&F for solid PVC wall Lining (Fluted type )Consisting of 5mm thick colour PVC sheet in Strips & Channel feathered at the edge of fixing on solid PVC wall lining and solid PVC pertition inclusive of solvent cement and fixing at site but single side prelam PVC sheet used insted of plain colour sheet, complete all as specified and directed. |
| 101 | Providing and laying 80 mm thick factory made chamfered edge cement concrete paver block of M-40 grade with approved colour,design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed |
| 102 | M&L for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base of flooring complete all as specified and directed. |
| 103 | M&L Preparation old steel surfaces of any desription and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 104 | Supply and fix Steel rolling shutters, (Thickness of laths 1.25 mm ) with ball bearing, as specified including top cover, an choring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete:gear operated type with bevel gear box and crank handle including two coats of synthetic enamel paint over a coat of red oxide primer complete incl. dismantalling of old shutter complete all as specified and directed. |
| 105 | S&F safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed. |
| 106 | Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete with fittings and fixtures such as switches, ceiling roses, pendants, regulators, socket, lamp holders brackets, bulk head fittings etc removing material for taking credit ( credit shall be recovered as per credit Sch attached) and also making good disturbed surfaces of wall, floors etc complete all as specified and directed. |
| 107 | M&L for point wiring with 1.50 sqmm in copper conductor cable ( multistrand) FRLS single core PVC insulated cable in and including PVC concealed conduit ( ISI Marked) of heavy duly with all accessories ie PVC gutties etc terminated in sunken/pressed metal flush box and white modular cover plate with frame for mounting of switches /sockets/ fan regulators etc and continuous earth wire 1.5 Sqmm copper cable PVC insulated FRLS controlled by one switch for one light/fan/sockets point/ complete all as specified and directed in ceiling Portion surface conduit wiring to be done. Note : i) Eye/bottle thimbles shall be used for connection in switches/sockets & MCB's in DB's without any extra costii) Electric rewiring should be done in proper colour coding i.e. Red for phase, Black for neutral and Green for Earth.(iii) Necessity cutting chasing where ever required shall be part of job & making good the disturbed surfaces shall be part of job. |
| 108 | All as per item No 106 above, but for one 3/5 pin socket outlet 5 Amp on independent board complete all as specified and as directed. |
| 109 | All as per item No 106 above, but for one 3/5 pin socket outlet 5 Amp on the same board with other switches complete all as specified and as directed. |
| 110 | All as per serial item No 106 here-in-before , but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor ( Multi-stranded) PVC insulated and unsheating electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 2.5 Sqmm copper stranded conductor as continuous earth wire connected to common earth dolly complete all as specified and as directed |
| 111 | Supply & fixing in replacement of Modular switch 1 way 6A, 1 module type complete all as specified and directed. |
| 112 | Supply & fixing in replacement of Modular switch 1 way 16A, 1 module type complete all as specified and directed. |
| 113 | Supply & fixing in replacement of Modular Socket, 6A - 5 pin 2 module type complete all as specified and directed. |
| 114 | Supply & fixing in replacement of Modular Socket 6A/16A - 2/3 pin 2 module type complete all as specified and directed. |
| 115 | Supply and Fixing in replacement of LED light fittings 1 x 20 Watt, 220 V, AC decorative box type with driver, holder including LED tubelight connecting up with three core flexible copper conductor cable of size from ceiling rose including mentioning MES No. with black/white synthetic enamel paint complete all as specified and directed. |
| 116 | Supply & fix in replacement of LED 10 Watt, 2 feet long, Cool day light with NEO Batten10 W 6500K having high efficiency Cat No. LHEXACP7IN1W010. Make -Havells. incl necessary electric conection including mentioning MES No. with black/white synthetic enamel paint complete all as specified and directed. |
| 117 | Supply & fixing in replacement of modular ceiling rose surface type, 65 mm x 50 mm two to three terminals / PVC / polycarbonate, isolated body fixed on PVC block complete all specified and as directed. |
| 118 | Supply & fixing in replacement of lamp holder modular type, PVC/ polycarbonate type with back plate suitable for 7 to 18 watts complete all as specified and directed. |
| 119 | Supply & fixing in replacement of LED inverter Bulb 9 Watt (CDL) cool day light, Model- 9 W B22 LED of make Havells or equivalent as approved by GE, Inverter Bulb Cool Daylight, LHLDEGEDML8O012 complete all as specified and directed. |
| 120 | Supply & fixing in replacement of LED inverter Bulb, Cool Day Light, Energy Efficient, Glare Free Soft Light, Power Backup Feature, inbuilt Overcharging Protection, inverter Bulb 15 Watt (CDL) cool day light type, Model - 15W LED B22D of make Havells or equivalent as approved by GE complete all as specified and directed. |
| 121 | Supply & fixing in replacement of LED light fitting 1x9W/1X10W bulkhead luminaires 230 Volts including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size including mentioning MES No. with black/white synthetic enamel paint complete all as specified and directed. |
| 122 | Supply & fixing in replacement of call bell ding dong AC 230 volt single pole complete all as specified and directed. |
| 123 | Supply & fixing in replacement of Modular Bell push 6A 1 module complete all as specified and directed. |
| 124 | M & L for Fan step regulator, 120W - 1 module complete all as specified and directed. |
| 125 | S&F in replacement of Energy saving ceiling fans complete with blades, down rod and with all accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM five star rated with brushless direct current motor (BLDC) with remote control including mentioning MES No. with black/ white synthetic enamel paint on ceiling fan complete all as specified and directed.(Note:-Unsv C/Fan will be deposted to MES office). |
| 126 | Supply and fix in replacement of exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm sweep grouting and making good the disturbed surface shall be part of job at no extra cost including mentioning MES No. with black/ white synthetic enamel paint on exhaust fan complete all as specified and directed.(Note: - UNSV Exhaust Fan will be deposited to MES office). |
| 127 | S&F in replacement of Exhaust fan 300 mm sweep, metal body type AC single phase 240 V with louver including mentioning MES No. with black/ white synthetic enamel paint on exhaust fan complete all as specified and directed.Note : (i) Fixing of exhaust Fan on wall with suitable size anchor bolt, cutting wall for making hole suitable for 300 mm sweep exhaust fan, grouting and making good the disturbed surface shall be part of job at no extra cost. (ii) UNSV Exhaust Fan will be deposited to MES office). |
| 128 | Supply and fixing in replacement post top lantern LED type 20 watt 230 watt volts AC outdoor type with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion resistant complete with driver and lamp complete all as specified and directed. |
| 129 | S&F in replacement of SPN DB suitable for MCBs of single pole and neutral 12 Way as per IS - 8623, IP-54 protection,double door type with 200 amp rated bus bar complete all as specified and directed.Note: i) Connnections of the MCB'S shall be done with appropriate size of brass/Cooper thimble.(ii) Dismantling of existing sheet metal box will be deposited to MES.(iii) Masonry work to fill the space of iron sheet box will be part of the job.(iv) Energy Meter will be refixed & connected after fixing of new DB.(v) MCB'S shall be fixed with copper wires FRLS 1.5/2.5 Sqmm incl appropriate size of brass/ Cooper thimbles.(vi) Existing metal enclosure of SPN DB will be deposited to MES. |
| 130 | Supply and fix in replacement of MCB SP up to 6-32 Amp ('B' Curve) complete all as specified and directed. |
| 131 | Supply and fix in replacement of MCB SPN 6-32 Amp ('B' Curve) complete all as specified and directed. |
| 132 | M&L for Earthing complete with galvanized steel earth plate electrode 600x600x6mm tthick buried directly in ground(earth plate not less than 2.25 mtr deep below the normal ground level ) with top edge of plate not less than 1.5 mtr below the normal ground level connected to galvanized earth wire 4mm dia by means of nuts bolts,washers,check nuts of iron or steel including test point PCC pits and RCC cover in PCC 1:2:4 (type B-1) including iron angle frame 40*40*6mm. and medium grade GI watering pipe 20mm dia with funnel and wire mesh and 15 mm bore GI pipe light grade proection pipe including excavation and charcoal ,common salt surrounded with 15cm all around the plate all as specified and shown in EP-3 of SSR Part-I, complete all as specified and directed. |
| 133 | S&F in replacement of new generation energy saving and environmental friendly long life LED building security light 1x25/35 watts made up of pressure die cast alluminium housing with high power LED as light source and lense embedded PC cover having TOP OPENING separate driver compartment with IP65 protection and impact resistance of IK07, with all accessories including suitable bracket with suitable dia light grade GI pipe bend to shape, including MS clamp of size of required size and PVC cable 1.5 Sqmm twincore from ceiling rose to light fittings including mentioning MES No. with synthetic black synthetic enamel paint on LED light & also on pole with white synthetic enamel paint with background of blue enamel paintcomplete all as specified and directed. |
| 134 | S&F in replacement of Geyser (water heater) vertical storage type 240 volts, 2000 Watt, water proof IPX-4 Pprotection having adjustable knob for temperature settings, copper cell of 25 Ltr capacity, 5 star rating with all accessories such as safety valve, thermostate, NRV, connection piece etc. and incl cost of anchoring arrangement (nut & bolts) to the wall, corded copper electric cable etc incl dismantling of existing geyser including mentioning MES No with black synthetic enamel paint on geyser complete all as specified and directed (Note:-Unsv Geysers will be deposted to MES office. ) |
| 135 | Supply and fixing in replacement of XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 16 Sqmm, 2 core laid in trenches /on poles / walls / in ducts / passing through pipes and including necessary cable lugs, bolts, nuts and washers complete all as specified and directed. |
| 136 | Excavation in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth and getting out in any type of soil complete all as apecified and directed. |
| 137 | M&L for sand cushioning to under ground cables with a layer of sand 8 cm before laying the cable and 15 cm after laying the cable complete all as specified.Note: Only Punned soil shall be measured. |
| 138 | Returning filling in including, spreading,levelling,watering and well ramming in layers not exc 25cm thick each complete all as specified and directed. |
| 139 | Removing excavated material to a distance not exc 50m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed. |
| 140 | Supply and laying GI tube 40 mm light grade as in cable protection pipe including all fittings & taking down / taking out from trench complete all as specified and directed. |
| 141 | M&L for trench less drilling of Road/ PCC surface by Machine without damaging nearby area, depth as per site requirement for crossing of LT cables protection pipe incl cost of PCC 1:3:4 for making good the disturbed surface of road/ floor/ PCC all as specified and directed. |
| 142 | M&L for laying of well burnt Brick 23 cm x11.5 cm x7.5 cm for cable protection complete all as specified and directed. |
| 143 | Supply and fixing LED flood light 200 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp incl fitting & fixture including mentioning MES No. with black synthetic enamel paint on LED light & also on pole with white synthetic enamel paint with background of blue enamel paint complete all as specified and directed. |
| 144 | S&F Metal body Turboforce air circulator wall fan energy saving 5 star rating 600 mm sweep energy efficent Model FHACWSTGRY24 of make Havells or equivalent as approved by GE as per latest specifications having 230 Volts incl anchoring arrangement complete all as specified and directed. |
| 145 | Supply and fixing Vertical load line type TPN DB, 8 way 415 V, double door as per IS - 8623, IP-54 protection, universal mounting with suitable capacity copper bus bar with nuetral bus bar, earth bar and cable ties for cable management, top and bottom removable gland plate suitable for accomodate MCCB TPN 100 Amp as incomer and TP&SP MCCB/MCBs as outgoing complete & making necessary electrical connection for incoming and outgoing cables, with copper lugs, crimpped with crimping tool complete all as specified and directed.Note: (i) Connnections of the MCB'S shall be done with appropriate size of brass/Cooper thimble.(ii) The disturbed surface shall be match with existing shall be part of job. |
| 146 | S&F in replacement of existing MCCB TPN, 100 Amps, 415 volts, 16 KA complete fixing in DBs including proper thimbles connections complete all as specified and directed. |
| 147 | M&L for Sub main wiring with 2 runs of single core FRLSH PVC insulated unsheathed multistranded copper conductor cable of size 2x6 sqmm ( line conductor) & 1x6 sqmm ( earth conductor), 1100 volt grade drawing in & including heavy duty non metallic PVC conduit , ISI marked, incl accessories not less than 25 mm in dia & concealed in wall, roof etc including PVC insulated, FRLSH unsheathed single core multistranded copper conductor cable, green in colour as earth conductor including cutting charges for concealed conduit wiring etc and making good cutting not exceeding 10 cm grith complete all as specified and directed.Note:(i) Electric rewiring should be done in proper colour coding i.e. Red for phase, Black for neutral and Green for Earth.(ii) Connections of cables with MCBs or bus bars shall be done through brass/copper thimbles of appropriate size.(iii) Two runs of copper conductor cable and one run of copper earth wire including PVC conduit will be measured and paid as one unit only |
| 148 | M&L in replacement for Sub main wiring with 2 runs of single core FRLSH PVC insulated unsheathed multistranded copper conductor cable of size 2x4 sqmm ( line conductor) & 1x4 sqmm ( earth conductor), 1100 volt grade drawing in & including heavy duty non metallic PVC conduit , ISI marked, incl accessories not less than 25 mm in dia & concealed in wall, roof etc including PVC insulated, FRLSH unsheathed single core multistranded copper conductor cable, green in colour as earth conductor including cutting charges for concealed conduit wiring etc and making good cutting not exceeding 10 cm grith complete all as specified and directed.Note: (i) Electric rewiring should be done in proper colour coding i.e. Red for phase, Black for neutral and Green for Earth.(ii) Connections of cables with MCBs or bus bars shall be done through brass/copper thimbles of appropriate size(iii) Two runs of copper conductor cable and one run of copper earth wire including PVC conduit will be measured and paid as one unit only. |
| 149 | Supply and install hi wall split Air Conditioner units indoor/outdoor complete with cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality with 5 star rating and EER 3.2 of capacity 2 TR complete all as specified and directed. |
| 150 | Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 5 KVA complete all as specified and directed. |
| 151 | S&F in replacement of existing unserviceable Plug & Socket Box (sheet metal) with PVC Plug, SPN 20 Amps for Acs Note : (i) Including cost of masonary work involved and the disturbed surface shall be repaired/match with existing shall be part of job. Model No. - DHDPHSN020 of make Havells or equivalent as approved by GE, complete all as specified and directed. |
| 152 | Supply and fix in replacement of recess mounted LED luminaire 28 Watt Warm White complete with all accessories incl cost of lamp & detachable driver suitable for false ceiling, dimensions, (600x600x70) mm. complete all as specified and directed. |
| 153 | Supply and fixing in replacement of XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 35 Sqmm, 3.5 core laid in trenches /on poles / walls / in ducts / passing through pipes and including necessary cable lugs, bolts, nuts and washers complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 02, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 23, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 17 daysJul 25, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 19 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender