Tender For Comprehensive Repair To Otm Accn Of Mh, Transit Cell, Adm Area And Offrs Mess Etc Under Age B/R-Ii Ge (Kh)Yol
Tender Value
30 Lakhs
Estimated cost
Bid Submission
16 Jul 2026
7 days left
EMD
60000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kangra → Himachal Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Comprehensive Repair To Otm Accn Of Mh, Transit Cell, Adm Area And Offrs Mess Etc Under Age B/R-Ii Ge (Kh)Yol
BOQ
| Sl. No. | Item Description |
| 1 | Taking down chowkats or frames with shutters (w/o taking of shutters from the frame) n.exc 1.5 Sqm each complete all as specified and directed. |
| 2 | Taking down chowkats or frames with shutters (w/o taking of shutters from the frame) exc 1.5 but n exc n.exc 4 Sqm each complete all as specified and directed. |
| 3 | Taking down shutters of any description exc 1 sqm and n exc 2 sqm each complete and removing from site all as specified and directed. |
| 4 | Taking down shutters of any description n exc 1 sqm each complete and removing from site all as specified and directed. |
| 5 | Pressed steel frames of size 125x60x1.25mm for door with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, including one shop coat of red oxide zinc chrome primer including back filling with PCC M-15 (nominal mix) type B-0 using 12.50mm graded crushed stone aggregate, complete all as specified and directed. |
| 6 | Dismantling timber in scantling 40 sqcm and over in section unframed work complete all as specified and directed. |
| 7 | Dismantling posts or struts (Wood, steel or RCC) any section, including taking out embedded portion and making good disturbed ground complete all as specified and directed. |
| 8 | 2nd class hard wood (Sal/Hollock) plain, solid, straight chowkats and frames, wrought, framed, rebated on solid, rounded or chamfered, put together with glue, pinned at joints with one or more rebates, complete all as specified and directed. |
| 9 | S&F for 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type decorative veneers of required design on both sides complete all as specified and directed. |
| 10 | Factory made 2nd class hard wood (Sal/ Hollock) plain, framed, panelled 35mm thick shutters without interlocking rail and with one paneland panels of 9mm BWP commercial plywood or 12mm veneered particle with commercial face veneers on both sides.The size of rail and style as per IS–1003 (Part-I), kiln seasoned and chemically pressure treated, complete all as specified and directed. |
| 11 | S&F for 35 mm thick 2nd class hardwood glazed and skeleton shutters , open rebated and prepared to receive glass, guaze, etc.(without sash bars), edges of framing plain chamfered or rounded fitted with cut and metered beads for securing glass etc . sizes of members of shutters as specified in SSR-I , section-8, clause-8.24(a); supplied and fitted to chowkats, complete all as specified. |
| 12 | Factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing on page No 180 of MES SSR 2020 Part-II, complete all as specified and directed. |
| 13 | Factory made solid PVC moulded door shutter 28mm - 30mm thick (stiles) with particle board core with 2,4,or 6 raised panel design with 2mm thick moulded PVC sheet on the front face and 2mm plain colour PVC sheet on back ,supplying and fixing in frame at site complete all as specified and directed. |
| 14 | Factory made fully glazed (frosted/ground/obscured)/ fully gauged PVC window/ventilator shutter 30mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC C Channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top and bottom rail on either side and as gap inserted for top and bottom rail(rate incl glass panes/gauges) all as specified and directed. |
| 15 | Steel window 1.25mm thick box type (Primer coated) ERW hollow P section of size 85mmx35mm double rebated comprises gauged, glazed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with two openable leaf consiting two Nos sash bar of T-Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 30mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC M-15, type B-0 (04 No's for each window, steel duly painted with one shop coat of zinc chromate primer on prepared surfaces) and finishing the surfaces to match with existing including 10mm square bars grill and following fitting welded to frame shutter:- (i) Hold fast, 150mm long of 12mm x 3mm made to shape -04 Nos per window. (ii) Handle of Z section 20mm x 25mm, 100mm long -1 No per leaf. (iii) MS tower bolt 150mm long - 2 No per leaf. (iv) Z section 20mm x25mm, 100 long stopper - 1 No per leaf. (v) Cleat 65mm long of hollow square 15mm x 20mm x 63mm welded to hinge -1 No per leaf. (vi) Mild steel pintle hinge of size 75mm x 12mm - 2 Nos per leaf. (vii) Flat iron fillets of size 20X3 mm for fixing wire gauge. (viii) Fabrication & fixing arrangement as per drg No. CEPZ/ TD 26/03. Note:- Above referred drawing has not been made part of tender. The same can be seen in the office of GE during working hours on any working day. |
| 16 | Powder coated Anodised aluminium frame for doors, windows, ventilators, partition with one or more rebates including joining cleat for fixing etc. complete all as specified |
| 17 | Powder coated Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified |
| 18 | S&F powder coated Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified |
| 19 | Powder coated 15 micron sliding three track anodized aluminium window chowkhat with shutter of approved design complete with all fixing arrangements including providing and fixing window handles, tower bolts, hydraullic door closer and mortice lock, hinges, door stopper including neoprene lining. The member shall made out of extruded aluminium sections comprising of :- (a) Shutter vertical member 47.62 x 45.45 x 1.74mm weighing 0.881Kg/RM. (b) Shutter top member 47.62 x 44.45 x 1.14 mm weighing 0.607 Kg/RM. (c) Shutter bottom member 47.62 x 44.45 x 1.14mm weighing 0.607 Kg/RM. (d) Natural colour 15 micron anodised aluminium anodised frame of chowkhat of section 85x44.45x1.80mm weighing 1.302 Kg/RM, with flat iron hold fasts and necessary concrete to fix hold fasts all as directed. (e) 5.50mm thick tinted sheet glass fixed with alumnium beading, silicon lining and gaskets. (f) The size of Anodised aluminium round handle, fancy type shall be 100mm dia (02 Nos) and aluminium anodised aluminium tower bolt of size 100mm (02 Nos). |
| 20 | S & F aluminium anodized Mortice lock 4/6 levers of any type and size or description as per site requirement complete all as specified. |
| 21 | Aluminium (diecast) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed in repair, complete all as specified and directed. |
| 22 | 5.5mm thick sheet glass, ordinary quality and glazing with oil putty or with aluminium glazing clips rubber neoprene packing in square exc 0.5 sq. m in each pane with Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as per specified and directed. |
| 23 | S&F for 4 mm thick figured glass, pin head type and glazing with oil putty, aluminium glazing clips, PVC strip etc. in squares n exc 0.5 sq. m in each pane all as per specified and directed. |
| 24 | S&F for Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with finned tacks of galvanised wire staple fixed with stainless steel wire staples, aluminium glazing clip and rubber neoprene packing complete all as specified. |
| 25 | S&F for 4mm thick sheet glass, ordinary quality and glazing with oil putty/ wooden beads in square pane not exc 0.50 Sqm each pane in wooden/steel windows, aluminium glazing clip and rubber neoprene packing complete all as specified. |
| 26 | S&F for Steel locking bolts with mild steel electrogalvanised plate and bright bolt not less than 6 to 8mm dia 100mm size all as specified. |
| 27 | S&F for 100mm size butt hinges medium weught , cold rolled Mild Steel all as specified. |
| 28 | Mild steel butt hinges (ISI marked) cold rolled medium weight of size 75mm, complete all as specified and directed. |
| 29 | Aluminium anodised, (ISI marked), barrel tower bolts of extruded section, length of bolt 100mm, fixed, complete all as specified and directed. |
| 30 | Extruded aluminium alloy handles (ISI marked), fabricated type, anodised, of size 100mm, complete all as specified and directed. |
| 31 | Extruded aluminium alloy handles (ISI marked), fabricated type, anodised, of size 75mm, complete all as specified and directed. |
| 32 | S&F for 300 mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections or cast-aluminium alloy fixed in position by means of welding or bolting etc all as specified and directed. |
| 33 | S&F for Mild steel 300mm, ordinary rat tail rod patttern springs including roller and roller plate complete all as specified. |
| 34 | S&F for 2nd class hard wood small fittings such as brackets of any type, latch and hinge blocks, shaped door/windows stops and the like, including all necessary' labours; articles n exc 200 cu. cm each including butt hinges, size 50 mm, medium weight, cold rolled mild steel, and fixed complete all as specified. |
| 35 | M&L for 18/19 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work as in cub board shutters/selves and the like, etc.; including dismantling unservicable board any description all as specified. |
| 36 | S&F for 75 mm hasp and staple, safty type, aluminium anodised with mild steel hinge pin incl bolt to hinge plate and fixed with screws complete all as specified. |
| 37 | S&F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised Width of flaps (when open) in 40mm, complete all as specified and directed. |
| 38 | S&F in repair With magnet catcher with magnet for cupboards complete all as specified and directed. |
| 39 | Preparation of CGI/PGI sheet roof surfaces by removing all loose gravel, dust, dirt, corroson, oil, grease and other foreign materials by jet of dry air and clean the CGI/PGI sheet surfaces mechanically or by grinding to make the surfaces smooth and M & L for applying ShaliSeal PS PG conforming to SI-12118 Part-I; 1987 to seal holes of J/L hooks and applying one coat of cold applied adhesive ShaliBond APP @3.00 Sqm per kg (Approx) on CGI/PGI sheet surfaces as bonding adhesive to affix bituminous membrane with brush.S & F for unroll the APP membrane 1.50 mm thick (TarFelt APP conforming to ASTM D-5147) over the tacky surface and bond it to the CGI/PGI sheet surfaces by applying uniform pressure and finaly membrane shall be coated with Super Silver Sheild @ 7 to 9 sqm/ltr to protect the membrane from UV rays and prevent degradation arising of exposure to sun light. NOTE:- Roof treatment shall be carried out by expert applicator of the firm |
| 40 | Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15 cm thick above or below ground level complete and disposal of unserviceable material, debris and rubbish to a distance exceeding 1.5 Km but not exceeding 2Km complete all as specified and directed. |
| 41 | Plain cement concrete M-10, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate, 50mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified. Note:- The unit rate include for use of form work (straight or curved). |
| 42 | Dismantling floor, hearth or wall tiling including cement mortar bedding (But not backing), removing and rubbish of the premisses, complete including removal of debris to a distance exc 1.5 Km but n exc 2 Km, Complete all as specified. |
| 43 | Non skid ceremic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15 mm thick screed bed in cement mortar 1:4, complete all as specified. |
| 44 | Vitrified tiles 10 mm thick, light shade (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified. |
| 45 | Vitrified tiles 10 mm thick, light shade (square/rectangular) polished on vertical surfaces such as skirtings, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 10 mm thick rendering in cement mortar 1:3 complete all as specified. |
| 46 | M&L for Glazed ceramic coloured tiles 450mm x 300mm x 7 mm thick as in vertical surfaces such as skirting, dado etc set and jointed in neat cement slurry pointed in white or coloured cement to match over and includind 10 mm thick rendering in cement mortar 1:4 to receive tiles, complete all as specified. |
| 47 | Demolition of cement concrete reinforced of any description in any position complete including removal of debris to a distance exc 1.5 Km but n exc 2 Km, complete all as specified. |
| 48 | M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for coloumns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified. |
| 49 | 18-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over and including 15 mm thick screed base in cement mortar 1:4 over and complete all as specified and directed. |
| 50 | Reinforced cement concrete, M-15 (Nominal mix), type B-1, (with 20mm graded crushed stone aggregate as) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, including use of necessary form work complete all as specified and directed. |
| 51 | Taking down existing water proofing treatment (including cement plaster and cleaning with wire brushes roughening the surface and hacking out dirt where directed and diposal of rubbish not exc 500 mtr distance from starting point)/ cement or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. |
| 52 | 15mm thick (average) screed bed /plaster in cement mortar 1:4 in order to maintain proper slope and base over existing roof surface for laying of APP based polymeric membrane, mixed with water proofing compound as per manufacturer's instructions finished even and smooth without using extra cement all as specified and directed. |
| 53 | Applying evenly a tack coat of bitumen 85/25 conforming to IS:3384-1986 over plastered surface at the rate of 1.2 kg per sq.m including cleaning surfaces of density 0.87-0.89 kg per litre at 25 degree celcius and viscosity 70-160 CPS(bitumen primer shall be of make as of membrane) including preparation of surfaces complete all as specified and directed. |
| 54 | APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt. not less than 150 gms/sqm) laid on primed surface by forced application dipped into APP modified mix and sealing all the overlap 75mm on length side and 100mm on width side of membranes by torching as per manufecturer's instructions by authorised applicator only after applying evenly a coat of bitumen on bottom of APP all as specified and directedembrane and on top of joints of APP membrane. |
| 55 | Disconnecting existing tanks of capacity exc 250 litres & n exc 1000 ltrs litres capacity, setting aside (or lowering if required) for repairs, cleaning etc and hoisting if required reconnecting and re-fixing in position including repairing cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc. and hoisting if required all as specified. |
| 56 | M&L for plain cement concrete 1:5:10 type E-2 (Using 40 mm graded brick aggregate) as in sunken floors, complete all as specified. |
| 57 | M&L for PCC 1:2:4, 25 mm thick type B0 (Using 12.50 mm graded aggregate) for sub base of flooring all as specified and directed |
| 58 | Water proofing treatment of sunken portion/water tank portion/slabin two coats @ 1kg per sqm(each coat) using shaliurethane-BTD of STP make or equivalent mentioned high solid content component Water based liquid applied elastometric water proofing membrane as ASTMC 836 and ASTMD 6083, thickness of the membrane shall be 1.50 mm having solid content of more than 80 % elongation of 500 + (-) 50 % laid over reinforcing layer on non woven geotextile mesh of 40/50 gms including applying self primer coat by diluting with 1:1 ratio @ 0.20 Kg per square metre and surface preparation, complete all as per manufacturer's instructions/ specifications including taking down existing treatment& plastercomplete all as directed. |
| 59 | Rendering cement plaster 10 mm thick in cement mortar 1:4 (1 cement :4 coarse sand) in two layers (5 mm thick first layer and 5 mm thick second layer), mixed with water proofing compound @ 3 % by weight of cement on fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, complete all as specified. |
| 60 | Demolition of stone/boulders or brick masonary built in cment mortor including all quoins, arches, pillars, etc but excluding ashlar facings, dresses stone work and precast concrete articles etc, complete all as specified. |
| 61 | Fly ash brick work with old size bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 (1 cement : 6 coarse sand), complete all as specified and directed. |
| 62 | Walling random rubble masonry with best quality locally available stone, uncoursed, well bonded, bedded, solidly hearted and built in cement mortar 1:4 (1 cement : 4 coarse sand), complete all as specified and directed. |
| 63 | Sink with drainage board made of stainless steel 1.00mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, including 40mm dia waste pipe & CP waste coupling, overall size 915mm x 460mm bowl size 410mm x 330mm x 160 mm, fixed in repair, complete all as specified and directed. |
| 64 | S&F in repair vitreous China urinals, half stall type (back or corner wall type) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern for gravity flow with brackets, flush pipe, grating and Union for discharge pipe including waste pipe all as specified and directed. |
| 65 | Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms), complete all as specified and directed by Engr-In-Charge. |
| 66 | Vitreous Chinaware squatting pan, ‘Orrisa pattern’ size 580 mm x 440 mm, snow white, with CI ‘P’ or ‘S’ trap, front or back inlet, integral foot rest with provision of plain cement concrete M-15, type B-1 using 20mm graded crushed stone aggregate, including making connections to trap and to flush pipe including CP jet etc complete all as specified, anti-syphonage pipe, fixed, complete all as specified and directed. |
| 67 | S&F in repair 10 litre capacity PVC, low level, valveless, syphonic action type flushing cistern, inlet ball valve, float valve, handle and fixing arrangement, 32 mm dia. PVC flushing pipe, PVC connection 15 mm size with PTMT nuts of length 450 mm and with CP brass coupling & PVC washer at both ends, complete all as specified. |
| 68 | Vitreous China wash down water closet (pedestal pattern), coloured including traps, connection to drain or outgoing pipe, flushing pipe, anti-syphonage pipe complete including fittings, PVC coloured seat cover and chromium plated jet including 15mm dia PVC connection 600mm with CP brass coupling nuts and PVC washers at both ends, fixed complete, fixed in repair, complete all as specified and directed. |
| 69 | Wash basins, Vitreous China (corner or Flat) size 550mmx400mm, crystal white with and including cutting for and pinning on ends of brackets, 450 mm long PVC connections 15mm size with CP coupling nuts at both ends, waste pipe of polythylene of low or high density or PVC of 32mm dia, 32mm dia waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange and bedded in red lead cement and other end fixed, screwed for iron pipe and fixed in repair, complete all as specified and directed. |
| 70 | S&F in repair Vitreous china pedestal type wash basin, white, flat back, size 550 X 400mm excluding taps, waste, chain and plug and pocelain stopper but incl brackets, cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and flexible waste pipe complete fixed in repairs. |
| 71 | S&F for PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches/fixed to wall of bore 110 mm, fixed in repairs, complete all as specified. |
| 72 | S&F for PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches/fixed to wall of bore 75 mm , laid in repairs, complete all as specified. |
| 73 | S&F for PVC (SWR) bend any radius 110 mm bore, fixed in repairs, complete all as specified. |
| 74 | S&F for PVC (SWR) bend any radius 75 mm bore, fixed in repairs, complete all as specified. |
| 75 | S&F for PVC (SWR) junction single (Single T) equal or unequal, 110 mm bore fixed in repairs, complete all as specified. |
| 76 | S&F for PVC (SWR) junction single (Single T) equal or unequal, 75 mm bore fixed in repairs, complete all as specified. |
| 77 | PVC (SWR) floor trap, plain with grating including jointing to waste pipe with solvent cement, dia of outlet 75mm, complete all as specified and directed. |
| 78 | S&F in repair Pillar tap for 15 mm bore, cast copper alloy, with capstan heads, chromium plated, screwd down high pressure, with or withou lettered 'hot' or 'cold' with long screwed shanks and fly-nuts, screwed for iron pipes all as specified and directed |
| 79 | Bib taps, fancy type 15mm bore, cast copper alloy, screwed down, chromium plated screwed for iron pipe or for brass ferrule and fixed in repairs, complete all as specified and directed. |
| 80 | Angle/stop valve, cast copper alloy, fancy type chromium plated, screwed down, high pressure, screwed both ends for 15mm bore iron pipe or for unions and fixed in repair, complete all as specified and directed. |
| 81 | Stop valve, cast copper alloy, fancy type, chromium plated with long shank and cup (concealed type), screwed down, high pressure, screwed both ends for 15mm bore iron pipe or for unions and fixed in repairs, complete all as specified and directed. |
| 82 | Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed. |
| 83 | S&F in repair PVC connections 15 mm size with PTMT nuts of length 450 mm, complete all as specified. |
| 84 | S&F in repair waste fittings 32 mm bore , brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed |
| 85 | S&F in repair towel rail 450 mm long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (Minimum weight 170 gms), complete all as specified. |
| 86 | Rotational moulded polyethylene water storage tank 500 Ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position with PVC float ball valve 20mm dia with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line including dismantling old cemented/ asbestos water/ PVC storage tank, all as specified. |
| 87 | Rotational moulded polyethylene water storage tank 1000 Ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position with PVC float ball valve 20mm dia with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line including dismantling old cemented/ asbestos water/ PVC storage tank, all as specified. |
| 88 | S&F in repair Brass CP Shower rose (Fancy type as apporved by GE/Engr in Charge) with or without swivel joints, any size including fixing to steel pipe or union complete all as specified and as directed. |
| 89 | 600mmx450mm bevelled edge looking mirror of selected quality with 6mm thick polished glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plug with CP brass screws and cup washers fixed, complete all as specified and directed. |
| 90 | 1200mm x 450mm bevelled edge looking mirror of selected quality with 6mm thick polished glass, with necessary fixing arrangements complete all as specified and directed. |
| 91 | Soap dish, vitreous China white, approximate size 160x160x90mm, chromium plated, fixed to plugs with chromium plated, brass screws, fixed, complete fixed in repair all as specified and directed. |
| 92 | Sheet glass shelf assembly 55cm long consisting of 5.50mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, fixed with chromium plated brass screws, fixed in repair, complete all as specified and directed. |
| 93 | Rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to grade Fe.410-W Gde E-250, quality A, steel work, complete all as specified and directed. |
| 94 | Dismantling plain or corrugated steel sheeting any gauge, thickness including Nainital or similar pattern roof covering, complete all as specified and directed. |
| 95 | S&F for Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with 'L' type or 'J' type hooks with grade of zinc coating 275 of 0.63 mm thickness all as specified and directed. |
| 96 | S&F for Plain, galvanised, mild steel sheeting, in ridges, hips and straight flashings (length and girth as fixed) with grade of zinc coating 275 of 0.80 mm thickness complete all as specified. |
| 97 | S&F for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 98 | S&F for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 99 | Taking down cement plaster on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water, etc. complete including removal of debris to a distance exc 1.5 Km but n exc 2 Km, Complete all as specified. |
| 100 | Rendering cement plaster 15mm thick in cement mortar 1:6 on fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, all as specified. |
| 101 | Rendering cement plaster 15mm thick in cement mortar 1:4 on stone masonry or surface other than fair faces of brick wall surfaces, surface finished even and smooth without using extra cement, all as specified. |
| 102 | 5 mm thick rendering in cement mortar 1:3 on concrete surfaces as in ceiling , chajjas, fin, facias etc and including applying cement slurry; surface finished even & smooth without using extra cement complete all as specified and directed . |
| 103 | Preparing of new plastered wall surface and applying two coat oil bound distemper over a coat 2 mm thick wall care putty on newly plastered surfaces, complete all as specified. |
| 104 | M&L for preparation of newly plastered surface of walls and applying two coat of cement base paint over a coat of primer complete all as specified and as directed. |
| 105 | Preparing of new plastered ceiling surface and applying two coat oil bound distemper over a coat of chalk whitining primer on newly plastered surfaces, complete all as specified. |
| 106 | Complete removal of existing treatment from wall and applying two coat oil bound distemper over 2 mm thick wall care putty on previously plastered surfaces, complete all as specified. |
| 107 | Taking up or down old 15 mm bore steel tubing fixed to wall and ceiling or laid in floor,with all fittings and fixtures and short lengths including cleaning for refixing, removal to store,complete all as specifed . |
| 108 | Taking up or down old 20mm bore steel tubing fixed to wall and ceiling or laid in floor,with all fittings and fixtures and short lengths including cleaning for refixing or removal to store,complete all as specifed . |
| 109 | Mild steel galvanized steel water tubing 15mm bore, medium grade, including all fittings, short lengths,fixed to wall or ceiling or laid in floor, complete all as specified and directed. |
| 110 | All as per item No. 124, above but except GI tubing, complete all as specified. |
| 111 | Mild steel galvanized steel water tubing 20mm bore, medium grade, including all fittings, short lengths,fixed to wall or ceiling or laid in floor, complete all as specified and directed. |
| 112 | All as per item No.126, above but except GI tubing, complete all as specified. |
| 113 | Mild steel galvanized steel water tubing 32mm bore, medium grade, including all fittings, short lengths,fixed to wall or ceiling or laid in floor, complete all as specified and directed. |
| 114 | M&L for Preparation of new or previously untreated wood and wood wood based surfaces of any description, over 10 cm in width or girth and finishing, applying two coat with synthetic enamel paint over pink primer, complete all as specified. |
| 115 | Preparetion of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified. |
| 116 | Taking down cement plaster/decayed concrete from RCC roof projections/upward parapet walls/ down ward facia/soffits and fins of RCC chajjas /beams/columns/balconies etc. Supply and fixing by means of nailing wire netting of galvanised wire 1.40 mm dia and mesh size 20 mm and brushing neat cement slurry with 3.00 kg of cement/sqm and M & L for 20 mm thick cement rendering in two layers of 10 mm each (top/final layer shall be rendered after final setting of under layer) in CM 1:3 on concrete surfaces including scaffolding at a height upto 7.00 mtrs. etc complete all as specified and directed. |
| 117 | S& F in repair 15mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in repair all as specified and directed. |
| 118 | S& F in repair 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in repair all as specified and directed. |
| 119 | S&F for 50 mm size mesh of powder coated anodised aluminium grill of 5 mm dia , apertaure of not exc 50 mm oblong type fixed to aluminium frame work for grill of window etc complete all as specified and directed. |
| 120 | S&F stainless steel kitchen plate rack of size 600x900x250mm (nearest higher size) hoisted & fixed in position with drills, PVC rawl plugs & chromium plated screws all as per manufacturer's instruction complete all as specified and directed by Engineer in Charge. Make: Blue Star, Nirali, Prayag or as approved by GE. |
| 121 | M&L for brass chromium plated jet spray for water closet with 1.0 mtr long flexible 15 mm dia bore pipe fixed to union in repair all as specified and directed. |
| 122 | Vitreous China wash down water closet (pedestal pattern) with flushing cistern (single piece), coloured of size 800 mm X 375 mm X 650 mm including traps, trap distance 180 mm connection to drain or outgoing pipe, , flushing pipe, anti-syphonage pipe complete including fittings, PVC coloured seat cover and CP jet including PVC connection, fixed complete including demolition of old unservicable WC and provision of PCC M-15, type B-I, using 20mm graded crushed stone aggregate all as specified. Make: Cat Part No. ARS-WHT-39751P and ARS-WHT-39201 of Jaquar or equivalent makes mentioned in Appx 'C' |
| 123 | Wash basins, Vitreous China counter table top (Oval shape) size 420mm x 420mm x 135mm, coloured, fixed in granite counter by making suitable holes, new brackets with and including cutting for and pinning on ends of brackets, 450 mm long PVC connections 15mm size with PTMT coupling nuts at both ends, trap, grating and Union for discharge pipe, waste, chain and plug and porcelain stopper, waste pipe of polythylene of low or high density or PVC of 32mm dia including, 32mm dia waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange and bedded in red lead cement and other end fixed, screwed for iron pipe and fixed, complete all as specified. Make: Cat Part No. ARS-WHT-39901 for wash basin of Jaquar or equivalent in makes mentioned in Appx 'C'. |
| 124 | S&F health faucet (ABS body with 1 metre long easy flex in chrome finish tube and wall hook complete with accessories, fixed in repairs all as specified and directed by Engineer in Charge. Make Jaquar, Cera or Equivalent |
| 125 | Single lever WHB centre hole mixer for 15mm bore pipe of make jaquar, Cera or equivalent all as specified and directed by Engineer in Charge. |
| 126 | S&F in repair toilet paper holder CAT No CAN-1153S Make jaquar or equivalent all as specified and directed by Engineer in Charge. |
| 127 | 10mm thick toughened glass with 25 micron solar reflective film fixed with aluminium glazing clip and rubber neoprene packing all as specified. |
| 128 | S&F for aluminium anodised door stopper fixed at bottom of aluminium door shutter minimum length 75 mm & 50 mm width and upto 200mm length complete all as specified and directed by Engineer in Charge. |
| 129 | M&L for slate tiles best quality available fixed on wall with neat cement slurry/Paste including rendering 15 mm thick cement mortar 1:4 on stone masonry/brick masonry size and pattern to be as directed by Engineer-in-Charge. |
| 130 | M&L for 16mm thick parking tile, ceramic tile (square/Rectangular) polished area of each tiles not exceeding 0.36 sqm, in floors etc, Liight shade/Coloured, Shade as per requirment of site, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over 15 mm th bed/bedding layer of CM 1:4 complete all as specified and as directed by Enginer-in-Charge . Note : Sample will approved By GE. Make : SOMANY, KAJARIA, VARMORA. |
| 131 | M&L for 75 mm th PCC 1:3:6, Type C-2 (Using 40 mm graded aggregate) as in subbase of flooring all as specified and directed. |
| 132 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed. |
| 133 | M&L for plain cement concrete 1:2:4, Type B-1 (Using 20 mm graded aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed |
| 134 | Chequered cement concrete tiles machine pressed glossy finish of size 30cmx30cmx 25mm thick with grey cement, set jointed & pointed in neat cement slurry mixed with pigment to match the shade of the slab in floors laid over and including 15mm thick screed bed in cement mortar 1:4, complete all as specified and directed. |
| 135 | S&F in repais Stainless steel chromium plated curtain rod 25mm dia with fixing brackets, stops, rollers etc complete all as specified and directed. |
| 136 | Dismantling of ceiling Board (fibre, pulp, Insulation etc.) or insulation of boards/slab /blankets, any thickness with frame work including cover fillets cornices etc. complete all as specified and as directed. |
| 137 | S&F for 4mm thick non asbestos decorative E- board classic board fixed to aluminium anodised/ GI snap grid frame work of size of size 605 mm X 605 mm as in false ceiling, flat or sloping (pattern as per manufacturer's catalogue/ instructions), cutting holes for electrical fittings fixed on and including aluminium tee of size 25mmX25mmX1.50 mm as main runner, aluminium tee of size 25mmX25mmX1.25 mm as cross runner and aluminium angle of size 25mmX25mmX1.25mm at the perimeter suspended from soffit at approx 900 mm centre to centre with hangers 6 mm dia galvanised (length as per site requirement) adjusting level fixed to roof by means of ceiling cleats made out of galvanised iron flat 40 mm X 3 mm size, 60 mm long and expansion hold fasteners 12.5 mm dia, 40 mm long including necessary scaffolding all as specified and directed. |
| 138 | M&L for solid/ Hollow PVC Wall Lining consisting of 5mm thick wood grain printed PVC sheet used instead of plain colour sheet and fixing at site on PVC frame all as specified and directed. |
| 139 | S&F in repair Black out roller blinds of required and shade and necessary fitting of Johnson or equivalent Make complete all as per direction of Engr in Charge/GE |
| 140 | S&F in repairs for fabricating & installing in position 4mm thick aluminium composite cladding of pioneer, alutech, alstrong, aludecor are protected with self adhesive protection film by erecting over the wall using aluminium frames @ desired levels made with 50x25x1.2mm extruded channel sections confirming to IS 7333 mechanical properties, the frame shall be fixed on wall and floor surfaces with necessary brackets bolts nuts arrangements with screws aluminium L cleats bracket rod wacker/ dow corning silicon sealant etc at all levels & heights is filled in complete with necessary scafolding upto 7m height all as specifeid and directed |
| 141 | S&F for Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. complete all as specified and directed by Engineer in Charge. |
| 142 | Aluminium partition wall with top, middle and bottom frame of size 101.60mm x 44.45mm x 1.75mm weighing 1.36Kg per RM, partly glazed with 5.5mm thick tinted glasswith or without sash bars and partly panelled with 4/5mm thickACP board with side decorative laminated including rubber bead joining cleat in position complete, all as specified and as directed |
| 143 | Taking down and refixing of alumimium three/two track sliding window, Aluminium doors, Toughened Glass doors, Side hung type aluminium windows including with all fittings as in repairing to make serviceable and fixed in same opening complete all as specified and directed by Engineer in Charge. Note : Items used to make serviceable of existing one shall be measured and paid seperately except neoprene rubber beading, aluminium fillets etc. |
| 144 | Deduction to be made from BOQ for Sch 'A' Part - II (Schedule of credit) Note: Tenderers shall not quote for this schedule. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 02, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 16, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 7 daysJul 18, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 9 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender