Tender For Special Repair To Various Building And Certain Revenue Work Under Ge 859 Ews
Tender Value
Ref. Documents
Estimated cost
Bid Submission
17 Jul 2026
9 days left
EMD
87000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Tawang → Arunachal Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Various Building And Certain Revenue Work Under Ge 859 Ews
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) |
| 2 | Dismantling wrought iron or mild steel work of any description not otherwise provided fo |
| 3 | Dismantling Plain or corrugated steel sheeting, any gauge, thickness including nanital pattern or similar pattern roof covering, complete all as specified and directed by Engr-in-Charge. |
| 4 | Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out |
| 5 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed. |
| 6 | Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed. |
| 7 | M&L for Hardcore of broken stone or boldours of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed by Engr-in-Charge. |
| 8 | M&L for cement concrete 1:4:8 type D2 (40 mm graged aggregate) as in foundation and filling mass concrete complete all as specified and directed by Engr-in-Charge. |
| 9 | M&L for Type B1, 1:2:4 (20mm graded aggregate) Pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width and setting in mortar mortar 1:6, complete complete all as specified and directed by Engr-in-Charge. |
| 10 | M&L for Type C1, 1:3:6 (20mm graded aggregate) precast cement concrete solid building blocks or slabs 10cm thick (with plain or interlocking joints as directed) setting in mortar 1:6, complete, in walls complete all as specified and directed by Engr-in-Charge. |
| 11 | M&L for RCC (Nominal mix) Type B1, 1:2:4 (20mm graded aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed by Engr-in-Charge. |
| 12 | M&L for RCC (Nominal mix) Type B1, 1:2:4 (20mm graded aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed by Engr-in-Charge. |
| 13 | M&L for RCC (Nominal mix) Type B1, 1:2:4 (20mm graded aggregate) as in Columns, pillars, piers, posts and struts complete all as specified and directed by Engr-in-Charge. |
| 14 | Use and waste flat formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed by Engr-in-Charge. |
| 15 | Use and waste Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed by Engr-in-Charge. |
| 16 | Use and waste Square, Rectangula or polygonal Formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed by Engr-in-Charge. |
| 17 | M&L for second class hard wood in scantling, clean sawn, timber framed and fixed, complete all as specified and directed by Engr-in-Charge. |
| 18 | S&F 2nd class hardwood plain, solid, straight chowkats and frames, wrought framed rebated on the solid, rounded or chamfered put together with glue pinned at joints, complete all as specified and directed by Engr-in-Charge. |
| 19 | S&F 30mm thick 2nd class hardwood, Glazed and skelton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shuters as specified in SSR Part-I, Section 8, clause 8.24(a), fittted to chowkats, complete all as specified and directed by Engr-in-Charge. |
| 20 | S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. complete all as specified and directed by Engr-in-Charge. |
| 21 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed by Engr-in-Charge. |
| 22 | S&F 100mm aluminium anodised, barrel tower bolts of extruded section and fixed, complete all as specified and directed by Engr-in-Charge. |
| 23 | S&F 250mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed by Engr-in-Charge. |
| 24 | S&F 100 mm butt hinges, mediam weight, cold rolled mild steel and fixed complete all as specified and directed by Engr-in-Charge. |
| 25 | S&F 75mm butt hinges, mediam weight, cold rolled mild steel and fixed complete all as specified and directed by Engr-in-Charge. |
| 26 | S&F 100mm Aluminium handles, cast type, anodised complete all as specified and directed by Engr-in-Charge. |
| 27 | S&F 150mm Aluminium handles, cast type, anodised complete all as specified and directed by Engr-in-Charge. |
| 28 | S&F Framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed by Engr-in-Charge. |
| 29 | M&L for preparation of new or previously untreated steel surfaces of any description, not otherwise described over 10cm width or girth, and applying two coats of synthetic enamel paint over a coat of red oxide, zinc crome complete all as specified and directed by Engr-in-Charge. |
| 30 | S&F 1mm Mild steel, plain, black sheet in wall cladding,steel gates and similar work, cut to size, holes punched; including round headed screws,clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred |
| 31 | S&F Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in-Charge. |
| 32 | S&F Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in-Charge. |
| 33 | S&F Rolled mild steel work as in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed.(Fe-410 W(GdeE-250)quality B) |
| 34 | S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws asspecified complete all as specified and directed by Engr-in-Charge. |
| 35 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed by Engr-in-Charge. |
| 36 | M&L for 3mm thick cover fillet of standard hard board, 40mm wide and fixing with screws complete all as specified and directed by Engr-in-Charge. |
| 37 | M&L for 4mm thick Plywood, grade BWR, type BB, fixed with screws to timber frame work in ceiling, complete all as specified and directed by Engr-in-Charge. |
| 38 | M&L for 75 mm thk Cement concrete type B- 2, 1:2:4 (40mm graded aggregate) finished cement concrete even and smooth without using extra cement |
| 39 | M&L for 75mm thick Cement concrete type D2, 1:4:8 (40mm graded aggregate) as in sub base or in floors complete all as specified and directed by Engr-in-Charge. |
| 40 | M&L for 75mm thick PCC 1:3:6 type C2 (40mm graded aggregate) as in plinth protection complete all as specified and directed. |
| 41 | M&L for coloured Glazed ceramic tiles in vertical surface 350x 250x 7 mm/450X 300X 6to7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including rendering 10mm se tin CM 1:4 complete all as specified and directed by Engr-in-Charge. |
| 42 | M&L for Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by Engr-in-Charge. |
| 43 | M&L for Rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:4 complete all as specified and directed. |
| 44 | M&L for Rendering 10 mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even and fair without using extra cement complete all as specified and directed. |
| 45 | M&L for screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM 1:6, complete all as specified and directed. |
| 46 | M&L for Preparation of new plastered surface of wall and applying two coat of OBD over a coat of Priming plastered and other surfaces with alkali resistant priming paint complete all as specified and directed. |
| 47 | M&L for Preparation of new plastered surface of wall and applying two coat of cement base paint complete all as specified and directed. |
| 48 | S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed. |
| 49 | M&L for preparation of new or previously untreated wooden surfaces of any description, not otherwise described over 10cm width or girth, and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engr-in-Charge. |
| 50 | M&L for preparation of new steel urfaces of any description, over 10cm in width or girth,not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc crome complete all as specified and directed. |
| 51 | S&F 25mm dia 3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain &brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified and directed. |
| 52 | S&F 250Ltr capacity Rotational moulded polyethylene water storagetanks (cylindrical verticalwith closed top) hoisted and fixed in position all as specified in SSR Part I, complete all as specified and directed. |
| 53 | S&F 15mm dia fancy type Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. |
| 54 | S&F 15mm dia Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed. |
| 55 | S&F 20 mm Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed |
| 56 | S&F Waste coupling of PTMT 32 mm dia (half or full threaded) (Minimum weight 32mm - 45gms/40mm-60 gms) complete all as specified and directed. |
| 57 | S&F PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed. |
| 58 | S&F 110mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floorscomplete all as specified and directed. |
| 59 | S&F 110mm PVC (SWR) bends any radius complete all as specified and directed. |
| 60 | S&F 75 mm PVC (SWR) bends any radius complete all as specified and directed. |
| 61 | S&F vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including provn of lime concrete bedding, including Flush pipes to squatt pattern closet including all joints and making good to the floor, complete all as specified and directed |
| 62 | S&F PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including bracket High or low level fluslhing cistern (exclusive of brackets), and connections to pipes and fixing of chain and pull, or lever, if any complete all as specified and directed. |
| 63 | S&F Vitreous China wash basin, white, flat back, size 550x400mm excluding taps, waste, chain and plugs but including brackets complete all as specified and directed. |
| 64 | M&L for 10 users LLDPE septic tank designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, Vent shaft, connection etc., complete for |
| 65 | M&L for Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size 1.2 M dia X 3 M effective depth |
| 66 | S&F 25 mm Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed |
| 67 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc.removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. |
| 68 | S & F Switch flame proof rotary type with termination box in LM6, 16A, single pole 250V all as specified. |
| 69 | Supply and fixing in repair LED light fitting 40 Watt flame proof light CMRI certified recommended for gas/ vapor group of and IP 65 protection with die cast aluminum housing with heat resistant toughened glass, with LED light fixtures driver, holders, connector etc. Complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size fixing on truss with all fixing arrangement all as directed and as specified. |
| 70 | Supply installation testing and commissioning of flame proof DBs SPN 8 way suitable for use in hazardous area (Zone 1 & 2) of gas froup constructed from LM6 aluminum alloy with Ex-d enclusure, protection grade IP 65 or higher complete with necessary MCBs ( MCB SPN 32 Amps main incommer and MCB 6 Amps 06 Nos ) and internal wiring complete all as directed and as specified duly tested and certified by PESO/CCOE/CMRI/ATEX/IECEx for flameproof application.The unit shall be factory wired powder coated and weatherproof confirming to IS/IEC 60079. |
| 71 | Materials and Labour for earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6.0 mm thick buried directly in ground end vertically to a depth not less than 2.25 meter deep below ground level with top edge of the earth plate at a depth not less than 1.5 M below normal ground level connected to galvanized GI wire 4.0 mm as earthing lead by means of bolts, nuts check nuts and washers of galvanized steel and connected to main switch board or main control board as directed and provision of concrete pit in PCC (1:3:6) type C1, pre-cast including RCC (1:2:4) type B1, cover slab 54 cm x 54 cm x 5 cm, reinforced with 8 mm dia TMT bars @ 150 mm c/c both ways, one handle for lifting made out of 10 mm dia MS round bar, provision of funnel, wire mesh, 20 mm bore galvanized steel tubing (Medium grade) for watering, charcoal or coke and salt in alternate layers, 15 mm bore galvanized steel tubing (light grade) for protection of earth lead connection, including necessary excavation and earth work in any type of soil,and necessary testing complete all as shown on electrical plate No 5 of SSR Part –I (2009).Including taking down old item. |
| 72 | M & L for One light point or one fan point controlled by one switch with 1.5 sq. mm size FRLSH PVC insulated unsheathed single core multithreaded copper conductor cable 1100 volts grade incl 1.5 Sq mm PVC insulated unsheathed copper conductor cable as earth continuity conductor drown through in and incl PVC casing capping with its accessories and PVC Boxes for fixing switches/sockets etc. |
| 73 | M & L for One 3 pin socket outlet, 5 Amps on the same board with other switches, with cables 1.5 sq. mm size FRLSH PVC insulated unsheathed single core multithreaded copper conductor cable 1100 volts grade incl 1.5 Sq mm PVC insulated unsheathed copper conductor cable as earth continuity conductor drawn through in and incl PVC casing capping with its accessories and PVC Boxes for fixing switches/sockets etc. |
| 74 | M & L for One 3 pin socket outlet, 5 Amps, independent, with cables 1.5 sq. mm size FRLSH PVC insulated unsheathed single core multithreaded copper conductor cable 1100 volts grade incl 1.5 Sq mm PVC insulated unsheathed copper conductor cable as earth continuity conductor drawn through in and incl PVC casing capping with its accessories and PVC Boxes for fixing switches/sockets etc. |
| 75 | M & L for One 3 pin socket outlet, 15 Amps, independent, with cables 4 sq. mm size FRLSH PVC insulated unsheathed single core multithreaded copper conductor cable 1100 volts grade incl 4.0 Sq mm PVC insulated unsheathed copper conductor cable as earth continuity conductor drawn through in and incl PVC casing capping with its accessories and PVC Boxes for fixing switches/sockets etc. |
| 76 | S&F Switch piano, flush type single pole, one way 5 Amp. |
| 77 | S&F Switch socket combination 2 in 1, 5 A flush type. |
| 78 | S&F Switch socket combination 2 in 1, 3 pin, 5 and 15 Amp flush type Universal. |
| 79 | S&F Ceiling rose, 3 phase/PVC/ polycarbonate, isolated body. |
| 80 | Supply and fixing in repair LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete as specified. |
| 81 | Supply and fixing in repair LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete as specified. |
| 82 | Supply and fixing in repair LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete as specified. |
| 83 | S & F Lamp holder, PVC/Polycarbonate type with back plate suitable for battern fittings complete. all as specified and directed by as engineer-in-charge. |
| 84 | S&F LED Bulb 9 watt cat part no LED PLUS 9W B22 WW 2 STAR LAMP complete all as specified and as directed by engineer-in-charge. |
| 85 | Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz,RPM 1200, Copper winding of sweep 300 mm sweep with all fixing arrangement all as specified and as directed. |
| 86 | Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. |
| 87 | S&F of Single pole and neutral Sheet metal enclosure with a two pin and earth plug and socket complete with one single pole MCB SP 20 Amps, 240 Volts, AC,50 HZ, completete all as directed and specified, including taking down old unserviceable plug socket and offering for credit. |
| 88 | S&F sheet metal enclosure distribution box 4 way SPN 230 volts with 200 Amps rated bus bar single door complete including connecting up all as specified . |
| 89 | Supply and fixing MCB 32 Amp SPN 240V, 10KA 'C' complete with connection testing and commissioning all as directed and as specified. |
| 90 | Supply and fixing in repair MCB 5- 32 Amp SP 240V, 10KA 'C' complete with connection testing and commissioning all as directed and as specified. |
| 91 | S&F 3-layer PP-R Polypropylene random copolymer) 20 mm concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc |
| 92 | M & L for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 10 sq. mm 4.0 Core . |
| 93 | S&F XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 6 sq. mm 2.0 Core. |
| 94 | M & L for dismantling and taking up or down old unserviceable service cable /LT UG cable of any size complete all as specified and directed. |
| 95 | S&F High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 laid in trenches of size 20 mm bore. |
| 96 | Supply and fixing of GI tubing light grade of 32 mm dia for cable protection on pole/wall/floor/ or in trenches and drain etc complete with necessary clamp, nut, bolts and washers and socket and making good the disturbed surface of wall , floor or roof etc all as specified and directed, (Note : MS clamp, nut, bolts and washers measured and paid seperately) |
| 97 | M & L for PCC (1:2:4) type B1 using 20 mm graded aggregate for making good the disturbed portion of road/floor/platform etc including form work compaction etc all as specfied and directed by Engineer-in-Charge. |
| 98 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation of poles, etc. or for laying of cable, pier holes, etc. nexc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dense soil. |
| 99 | Supply install testing commissioning in repair of LT panel board out door type, floor mounted, free standing , dust and vermin proof,fabricated from 3.15 mm CRCA sheet,finished with powder coating & providing 200 Amp TPN aluminiumr Bus bar and wiring consisting of following items:-Incoming :- (i) MCCB 63 Amp,4 P,16 KA with spreader link - 01 No (ii) Digital voltmeter (0-500 V),CL-1 with selector switch - 01 No (iii) Digital Ammeter (0-100 A),CL-1 with selector switch - 01 No (iv) CT 100/5A,Tape wounded (v) LED Type indication lamp ,RYB - 01 SetOut going :- (i) MCB SPN 32 AMP - 02 Nos (ii) MCB SPN 40 AMP -02 Nos (iii) MCB TPN 16-32 AMP -02 Nos |
| 100 | M & L in repair for Air termination, single pointed aluminium rod 12 mm dia and 600 mm long. |
| 101 | M & Lin repair for Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hex. head screw. |
| 102 | M & L in repair for Aluminium strip 25 x 3.15mm with saddles and fixing screws etc. for roof conductors and down conductors above ground. |
| 103 | M & L in repair for PVC rectangular block for mounting, switches, sockets, fan regulator etc. with 3 mm thick plastic laminated sheet cover of size175 x 100 x 50 mm deep |
| 104 | M & L in repair for porcelain insulator fixing on wall/roof and fixing copper strip/aluminium strip above the porcelain insulator all as directed and specified. |
| 105 | S&F High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 laid in trenches of size 50 mm bore. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 02, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 17, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 9 daysJul 18, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 10 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender