Tender For Repairs To Walls, Tiles, Sunken Floor, Roof Sheet, Leakage, Seepage, Plinth Protection, Plastering Works Incl Roof Treatment, Roof Sheet And Petty Repairs At Zone Iii And Zone Iv Under Age B/R-Ii At Nagrota
Tender Value
30 Lakhs
Estimated cost
Bid Submission
22 Jul 2026
13 days left
EMD
60000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jammu → Jammu and Kashmir
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repairs To Walls, Tiles, Sunken Floor, Roof Sheet, Leakage, Seepage, Plinth Protection, Plastering Works Incl Roof Treatment, Roof Sheet And Petty Repairs At Zone Iii And Zone Iv Under Age B/R-Ii At Nagrota
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 08-Jul-2026 | REVISED BOQ | BOQ | 22-Jul-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling plain or corrugated steel sheeting, any gauze, thickness, including Nainital or similar pattern roof coverings etc complete all as specified and directed. |
| 2 | S&F for Pre-painted galvalume aluminum zinc coating GI based Corrugated sheet 0.50mm thick of required colour and design having tensile strength of 550 Mpa as in roof sheeting/sunshade/ wall cladding, north light curves, fixed with zinc coated self drilling fastener including EPDM washer complete laid with one corrugation side laps and min 150mm end lap laid to slope all as per manufacturer / profile maker instruction complete all as specified and directed. |
| 3 | S&F for Pre-painted galvalume aluminum zinc coating GI based plai steel sheet 0.50mm thick of required colour and design having tensile strength of 550 Mpa as in roof sheeting/sunshade/ wall cladding, north light curves, fixed with zinc coated self drilling fastener including EPDM washer complete laid with one corrugation side laps and min 150mm end lap laid to slope all as per manufacturer / profile maker instruction complete all as specified and directed. |
| 4 | Dismantling wrought iron or mild steel work of any description complete all as specified and directed. |
| 5 | Framed work 410-W as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing including hinges welding complete all as specified and directed. |
| 6 | M&L for Preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint complete all as specified and directed. |
| 7 | M&L for Preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth, and applying one coat of synthetic enamel paint complete all as specified and directed. |
| 8 | Dismantling of wall and ceiling boards(fibre, pulp,insulation etc) or insulation board/slabs/blankets any thickness including cover fillets complete all as specified and directed. |
| 9 | S&F for Anodised aluminium snap grid frame work of size 605mm x 605mm for false ceiling, complete all as specified and directed. |
| 10 | M&L for 4 mm thick non asbestos fibre cement building boards (size 600X600mm) fixed or laid / inserted to timber / GI / Aluminium frames work with screws as in ceiling flat or sloping incl refixing in position of electric wiring, lights and fittings etc, complete if exists complete all as specified and directed. |
| 11 | S& F in repair for 4 mm thick E Board classic desinger of size 600x600mm as in false ceiling or similar work complete all as specified and directed. |
| 12 | S&F in repairs POP 12mm thick Seamless calcium silicate ceiling made out of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25mm long self drilling and tapping screws having philips head with under head cutter at 200mm center to centre including finishing thr joints of face board with specially formullated jointing compound and 48 mm wide fibre tape to provide seamless finish with 12 mm thick for seamless false ceiling fixed with screw over and including Gl frame work comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete as per manufacturer instruction complete all as specified and directed. |
| 13 | S&F PVC sheet wall lining consisting of 5mm thick colour / printed PVC sheet inclusive of solvent cement and fixing at site including PVC frame as per specifications, complete all as specified and directed. |
| 14 | S & F false ceiling using 8–10 mm thick PVC panels of approved colour/printed/wood finish, size approx. 300 mm × 3000 mm, fixed to suspended GI framework (including perimeter channels, main and intermediate members at required spacing, hangers, fasteners, etc.), complete with all necessary PVC/GI trims, screws, edge finishing, making openings for electrical fittings/services, including cutting, wastage, labour, scaffolding and all accessories complete all as specified and directed. |
| 15 | Taking down & Refixing in Chowkats or Frame (without taking off shutter from the frame) for same opening n exc. 1.50 Sqm, complete all as specified and directed. |
| 16 | Taking down & Refixing in Chowkats or Frame (without taking off shutter from the frame) for same opening exc. 1.50 Sqm but n exc 4.00 Sqm each, complete all as specified and directed. |
| 17 | Taking down Chowkats or Frame (without taking off shutter from the frame) n exc. 1.50 Sqm, complete all as specified and directed. |
| 18 | Taking down Chowkats or Frame (without taking off shutter from the frame) exc. 1.50 Sqm but n exc 4.00 Sqm each, complete all as specified and directed. |
| 19 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube complete all as specified and directed. |
| 20 | S&F Factory made Solid Panel PVC Door Shutter 30 mm thick consisting of frame made out of MS tubes for Top & bottom nails MS framed shall be covered with neat moulded plain coloured PVC 'C' channel having PVC sheet ship if 20 mm width stuck inside with solvant cement for style and plain colour PVC shutters for top rail lock rail and bottom rail on edges side & gap insert for top rail bottom rail panelling of plain colour PVC sheet truck and nail with suitable PVC sheet bedding and jointed to shutter with solvent gear supply and fixing in the frame at site complete all as specified and directed. |
| 21 | S&F 100mm long Butt Hinges extruded aluminium alloy with Galvanised mild steel hinge pin, anodised and fixed complete all as specified and directed. |
| 22 | S&F 150mm long Extruded aluminium alloy Handles, fabricated type, anodised complete all as specified and directed. |
| 23 | S&F 125mm long anodised aluminium barrel tower bolt of extruded section ccomplete all as specified and directed. |
| 24 | Demolition of stone slabs of any description or thickness in kitchen platform, floors,aprons laid, bedded, pointing in any mortar etc complete all as specified and directed. |
| 25 | Material & labour for green marble stone of 18mm to 20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm screed bed in CM 1:4 complete all as specified and directed. |
| 26 | M&L Granite slab 16 to 18mm thick as in pillars, window cill, cooking platform and the like in cement motar 1:4 including painting in white cment 1:2 using marble dust with a mixture of pigment to match the shade of granite including cutting polishing and moulding on edges complete all as specified and directed. |
| 27 | M&L machine cut Kota stone slab flooring 18-20mm thick, laid over and incl 15mm thick cement screed /rendering in CM 1:6 ,laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl cutting, rubbing, gridding and polshing to achive mirror finish complete all as specified and directed. |
| 28 | M&L machine cut Kota stone slab in riser of steps,skirting,dado and pillar, 15mm thick, mixed with pigment to match the shade of the slab incl 10mm thick cement screed /rendering in CM 1:4 incl cutting, rubbing, gridding and polshing to achive mirror finish complete all as specified and directed. |
| 29 | Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for, complete all as specified and directed. |
| 30 | M&L for 75 mm thick PCC1:4:8 type D-2 using 40mm graded crushed stone aggregate as in foundation, sub base of floor, etc complete all as specified and directed. |
| 31 | Dismantling of floor hearth or wall tiling including cement mortar bedding but not backing coat, complete all as specified and directed. |
| 32 | M & L Cement concrete type B-0, 1:2:4 (12.5 mm graded crushed stone aggregate) 25mm thickness as in floor for laying tiles brushing with neat cement slurry @ 3.00 Kg/Sqm complete all as specified and directed. |
| 33 | M&L for Non-skid Coloured Designer Ceramic Tiles (Square/rectangular) area of each tile exceeding 0.06 sqm but n exc 0.11 sqm, 7-8mm thick in floors etc set & jointed in neat cement slurry & pointed in white or coloured cement to match including screed bedding layer of 15 mm thick in CM 1:6, complete all as specified and directed. |
| 34 | M&L for Non-skid Coloured Designer Ceramic Tiles (Square/rectangular) area of each tile exceeding 0.11 sqm but nexc 0.18 sqm, 7-8mm thick in floors etc set & jointed in neat cement slurry & pointed in white or coloured cement to match including screed bedding layer of 15 mm thick in CM 1:6, complete all as specified and directed. |
| 35 | All as per item No. 34 above but on vertical surfaces such as dados, skirtings and risers to steps, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:3 on masonry/ concrete surfaces complete all as specified and directed. |
| 36 | M & L for Glazed coloured ceramic tiles in vertical surface 350x 250x7mm / 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 10mm thk rendering in CM 1:3, complete all as specified and directed. |
| 37 | M&L for polished vitrified tiles light shade 10mm thick (square/rectangular) area of each tile exceeding 0.18sqm but not exc 0.36 spm in floor etc set and jionted in neat cement slurry and pointed white or coloured cement to match including roughning of concrete surfaces over 15mm thick screed bed in CM 1:4 complete all as specified and directed. |
| 38 | M&L for polished vitrified tiles light shade 10mm thick (square/rectangular) area of each tile exceeding 0.18sqm but not exc 0.36 spm in skirting etc set and jonted in neat cement slurry and pointed white or coloured cement to match including roughning of concrete surfaces over 10mm thick screed bed in CM 1:4 complete all as specified and directed. |
| 39 | Taking down cement plaster of any description on brick, concrete or stone walls or ceiling including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off complete all as specified and directed. |
| 40 | M&L for rendering 10mm thick CM 1:6 on fair faces of brickwork or concrete surfaces finished even & smooth w/o using extra cement complete all as specified and as directed. |
| 41 | M & L for rendering 15mm thick in two layer (10mm+5mm) in cement mortar 1:4 on fair faces of brick work / concrete surfaces finished even and smooth with out extra cement with WPC complete all as specified and directed. Note:- (i) water proofing compound on only top layer of plaster (ie 5mm thick)(ii) Qty of WPC 200ml per cement bag as per manufacturer instructions (iii) WPC shall be measured and paid separately) |
| 42 | M&L Rendering 5mm thick on fair faces of brick work or concrete surfaces in CM (1:3) in ceiling complete all as specified and directed. |
| 43 | Taking down cement plaster or decayed portision of concrete from ceiling, chajja, upward facia, downward facia in any position, any height (upto 3nd floor) and making good by, rendering 15mm thick with CM 1:4 or PCC 1:2:4 type B1 (using 20mm graded aggtregate) as in ceiling or concrete surfaces such as chajja, upward facia, downward facia and similar work finished even and fair including dubbing coat without use extra cement upto, any height (upto 2nd floor) including necessary scaffolding ccomplete all as specified and directed. |
| 44 | Supply only Liquid water proofing compound complete all as spesified and directed. |
| 45 | M & L for preparation of new plastered surface of wall and applying two coats of oil emulsion distemper over a coat of primer over a coat of wall care putty complete all as specified and directed.Note: (i) The painting is to be done using smart painting tools and technique as mentioned in Particular specification. Tenderer shall take this aspect in consideration before quoting his rates and no claim on account of misunderstanding or any thing else shall be admissible/acceptable at any later stage. |
| 46 | M&L for 2-3mm thick wall care putty on wall complete all as specified and directed. |
| 47 | M & L for Preparing New Surfaces of Walls and applying two coats of Cement base paint complete all as specified and directed. Note: (i) The painting is to be done using smart painting tools and technique as mentioned in Particular specification. Tenderer shall take this aspect in consideration before quoting his rates and no claim on account of misunderstanding or any thing else shall be admissible/acceptable at any later stage. |
| 48 | M&L for preparation of new plastered/unplastered surface and finishing walls with Acrylic Smooth exterior paint of required shade as approved by GE with two or more coats applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) on walls over 3mm thick plaster of paris putty including necessary scaffolding for max height of G+2 bldg with parapet, etc complete all as specified and directed.Note:- (a) Each stage i.e. preparation of surfaces, application of primer, application of first coat, application of second coat will be got passed from Engr-in -Charge.(b) The acrylic emulsion paint work shall be carried out by using smart painting tools and techniques as specified in Particular Specifications and Contractor will have to produce necessary documents for purchase of smart painting tools or rent receipt of these tools along with bill/RAR.The bidders are requested take this aspect in consideration before quoting their rate and no claim on account of misunderstanding or otherwise shall be admissible on this account. (c) The painting is to be done in one or more shades as approved by GE. |
| 49 | M & L for preparing new plastered surfaces of ceiling and applying two coats of oil emulsion distemper complete all as specified and directed. Note: (i) The painting is to be done using smart painting tools and technique as mentioned in Particular specification. Tenderer shall take this aspect in consideration before quoting his rates and no claim on account of misunderstanding or any thing else shall be admissible/acceptable at any later stage. |
| 50 | M & L for two coats of white wash on newly plaster surfaces of ceiling incl preparation of surfaces complete all as specified and directed. |
| 51 | Hacking Out Old Broken Glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed. |
| 52 | M&L for Sheet Glass, 3.00mm thick glazing with Beads or Oil Putty, not exc. 0.5 Sqm in Each Pane, complete all as specified and directed. |
| 53 | All as per Ser item No 52 above but Figured glass, pin head type in squares n exc 0.5 sqm each pane complete all as specified and directed. |
| 54 | S&F in repair 12mm thick toughned glass as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes, SS handles for doors of required size complete all as specified and directed. |
| 55 | Demolition of cement concrete in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete all as specified and directed. |
| 56 | M&L for providing 50 mm thick cement concrete 1:3:6 type C-1 using 20mm graded curshed stone aggregates as in plinth protection laid in alternate bays (n exc 2 Sqm each) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and directed. |
| 57 | Demolition of brick work built in cement mortar including all quions, arches, pillars etc but excluding ashlar facings dressed stone work and precast concrete articles complete all as specified and directed. |
| 58 | M&L for Brick work with sub class “B” bricks straight or curved on plan exc 6M mean radius build in CM 1:6 using all as specified using old size bricks complete all as specified and directed. |
| 59 | All as per ser item No 58 above, but except bricks. |
| 60 | M&L brick work in CM ( 1:4 ) with using sub class `B ` modular half brick work straight or curved on plan exceeding 6.0mtr mean radius complete all as specified and directed. |
| 61 | Demolition of reinforced cement concrete of any description and in any position for existing shelves, water tank stages etc, not otherwise described comlplete all as specified and directed. |
| 62 | M&L RCC type B-1 1:2:4 using 20mm graded crushed stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in kitchen shelves , etc complete all as specified and directed. |
| 63 | M&L for form work to suspended slab as in kitchen shelves, cubboards, drain slab etc.complete all as specified and directed. |
| 64 | M&L TMT bar 10 mm dia and over, cut to length, bent to shape required ,including cranking ,bending spirally for hooping for columns,hooking end and binding with and including mild steel wire and annealed not less than 9 mm dia or securing with clips complete all as specified and directed. |
| 65 | Taking down steel tubing and connection including cleaning or removal to store bore of pipe 15mm complete all as specified and directed. |
| 66 | Taking down steel tubing and connection including cleaning or removal to store bore of pipe 20mm complete all as specified and directed. |
| 67 | S&F 20mm bore GI tubing (medium grade) with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. |
| 68 | S&F 15mm bore GI tubing (medium grade) with all fittings and fixed complete to walls and ceiling or laid in floors/roofs complete all as specified and directed. |
| 69 | M&L for Cuttings chases for concealed water tubing of concealed conduit (cutting n.exc 10 cms girth) and making good in CM ( 1:3) in brick walls complete all as specified and directed. |
| 70 | Cleaning and removing all dirts and scales from service water tanks and from mouth of circulating pipes etc capacity of tank exceeding 250 ltr but not exceeding 500 ltr complete all as specified and directed. |
| 71 | All as per ser item no 70 above but exceeding 500 ltr but not exceeding 1000 ltr capacity complete all as specified and directed. |
| 72 | Disconnecting existing tanks nexc 500ltr capacity, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position complete all as specified and directed. (Cleaning repairing etc. measured separately). |
| 73 | Disconnecting existing tanks capacity of exc 500ltr and nexc 1000ltr , setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position complete all as specified and directed. (Cleaning repairing etc. measured separately). |
| 74 | Dismantling and removing to water storage tanks of capacity exceeding 250 ltrs but not exceeding 500 ltrs and removing to stores complete all as specified and directed. |
| 75 | Dismantling and removing to water storage tanks of capacity exceeding 500 ltrs but not exceeding 1000 ltrs and removing to stores complete all as specified . |
| 76 | S&F in repair for 500 ltrs capacity rotational moulded polythylene water storage tank trippled layer (Cylindrical vertical with closed top) hoisted including ball, brass valve 20mm high pressure with polythylene float and fly nuts screwed for iron pipes, all as specified in SSR Part I complete all as specified and directed. |
| 77 | S&F in repair for 1000 ltrs capacity rotational moulded polythylene water storage tank trippled layer (Cylindrical vertical with closed top) hoisted including ball, brass valve 20mm high pressure with polythylene float and fly nuts screwed for iron pipes, all as specified in SSR Part I complete all as specified and directed. |
| 78 | S&F in repair of 15mm bore valve high pressure of PTMT with epoxy coated aluminum rod & high density plastic ball screwed for iron pipes and fixed (Min Weight 15mm-142 gms) complete all as specified and directed. |
| 79 | S&F in repair of 20mm bore valve high pressure of PTMT with epoxy coated aluminum rod & high density plastic ball screwed for iron pipes and fixed (Min Weight 20mm-210 gms) complete all as specified and directed. |
| 80 | S&F in repairs gate valves 20mm dia with iron wheel head, screwed both ends for iron pipe complete all as specified and directed. |
| 81 | All as per ser item no 80, above but exceeding 500 ltr but not exceeding 1000 ltr capacity complete all as specified and directed. |
| 82 | Dismantling cast-iron/PVC pipes including fittings taking out of trenches or walls as required dia of pipe upto 100mm complete all as specified and directed. |
| 83 | S & F in repairs 110mm bore PVC (SWR) pipes singles socket in any length with rubber ring joints fixed to walls or floor or in trenches complete all as specified and directed. |
| 84 | S & F in repairs 75mm bore PVC (SWR) pipes singles socket in any length with rubber ring joints fixed to walls or floor or in trenches complete all as specified and directed. |
| 85 | S&F 110mm bore PVC (SWR) bends any radius complete all as specified and directed. |
| 86 | S&F 75mm bore PVC (SWR) bends any radius complete all as specified and as directed. |
| 87 | S & F 110 mm bore PVC (SWR), junction single, (Single T) equal or unequal complete all as specified and directed. |
| 88 | S & F 75 mm bore PVC (SWR), junction single, (Single T) equal or unequal complete all as specified and directed. |
| 89 | S&F in repair Stack clamps made out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100mm bore, complete all as specified and directed. |
| 90 | Supply and fixing in repairs Vitreous China Urinal, Half stall type, white with PTMT waste fitting, PVC waste pipe, brass CP urinal spreader including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws complete all as specified and directed. |
| 91 | S&F in repairs urinal spreader complete all as specified and directed. |
| 92 | S&F in repairs vitreous china wash down Water Closet white squatting pan Orissa pattern size 580x440mm with integral foot rest incl making necessary connections to soil pipes and flushing cistern complete all as specified and directed. |
| 93 | S/F in repair Vitreous china wash down water closet Pan (pedestal Pattern) white colour (excluding fixing bolt, flushing cistern and flush pipe) size 580 x 440mm with integral foot rest connecting flushing cistern and flush pipe complete all as specified and directed. |
| 94 | M&L for PVC Flushing Cistern 10 litre capacity low level valve less, symphonic action type white with inlet, ball valve, flaoat and handle including 32mm dia PVC Flush pipe a pair of cast iron brackets duly painted/erecting stand including cutting and pinning in ends, making good disturgbed surfaces in cement mortar 1:3 including taking down unserviceable flushing cistern complete all as specified and directed. |
| 95 | Supply and fixing in repairs internal fittings Kit complete for vitreous china flush cistern with twin flush complete all as specified and directed. |
| 96 | S&F flush pipe of polyethylene of low or high density or PVC, 32mm dia, for low level cistern complete all as specified and directed. |
| 97 | S&F in repair EWC seat cover for pedestal pan white / black closed pattern with flat bottom and cover and MS chromium plated aluminium hinge device, complete all as specified and directed. |
| 98 | S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed. |
| 99 | S&F in repair CP Seat jet with one meter PVC tube complete all as specified and directed. |
| 100 | S&F in repair Vitreous china Wash Hand Basin size 550x400mm (flat back or angle back type) including 32mm dia brass chromium plated waste fitting a pair if cast iron bracket duly painted/erecting stand including cutting and pinning in ends making good disturbed surfaces in CM 1:3 including taking down unserviceable wash hand basin and connected items of any description, complete all as specified and directed. |
| 101 | M&L for PVC Conncetions 15mm size with PTMT Nuts of length 450mm and fixed including taking down unserviceable PVC Connections, complete all as specified and directed. |
| 102 | S&F in repair CP Grating doom 100mm dia complete all as specified and directed. |
| 103 | S&F in repair angular Stop/Angle valve fancy type chromium plated,screwed down, high pressure with crutch or butterfly handle 15mm bore, complete all as specified and directed. |
| 104 | All as per ser item No 103, above but concealed type complete all as specified and directed. |
| 105 | S&F PVC waste pipe 32/40mm dia for WHB complete all as specified and directed. |
| 106 | S&F in repairs for Waste coupling of PTMT (half or full threaded) (Minimum weight 32mm-45gms/40mm-60 gms) complete all as specified and directed. |
| 107 | S&F stainless steel bottle trap for urinal and wash hand basin waste water outlet incl necessary fittings and connect to drain pipe, etc complete all as specified and directed. |
| 108 | S&F in repair, CP Bib taps cast copper alloy 15mm bore, screwed down high pressure with crutch or butterfly handle, screwdd both ends for iron pipe or for unions, complete all as specified and directed. |
| 109 | S&F in repair CP bib taps 15mm bore long body, fancy type, cast copper alloy chromium plated with crutch or butterfly handle screwed down for iron pipe or for brass ferrule and fixed, complete all as specified and directed. |
| 110 | Supply and fixing in repairs 15 mm bib tap standard of PTMT any colour high pressure screwed for iron pipe & fixed minimum weight 90gm/each complete all as specified and directed. |
| 111 | S&F Pillar cock 15mm bore fancy type chromium plated, screwed down high pressure with or without lettered HOT or COLD with long screwed and fly-nuts screwed for iron pipe or brass ferrule and fixed in repair complete all as specified and directed. |
| 112 | Supply and fixing in repair chromium plated brass swan neck pillar tap of approved make, 15 mm nominal bore, with elegant gooseneck spout, complete with operating lever/knob, aerator, and all necessary fittings including nuts, washers, PTFE tape, and connection to existing water supply line, cutting and making good the disturbed surfaces,complete all as specified and directed. |
| 113 | M&L for Repairing of old chromium plated bib taps, pillar taps, wash hand basin mixture, stop cock, angle valve, concealed stop cock and similar items by changing its brass phases and making it functional complete all as specified and directed. |
| 114 | Supplying and fixing in repairs the internal spindle (face) of 15 mm diameter stop cock / bib tap / angle valve, including taking down the fitting, dismantling as required, replacement of worn-out spindle/face with new one of approved make, refixing, testing for smooth operation and leakage, and making good the disturbed portion complete all as specified and directed. |
| 115 | S&F in repair CP mixer for mixing hot & cold water screwed down for iron pipe 15mm bore complete all as specified and directed. |
| 116 | S&F in repairs Brass chromium plated shower rose 125mm size with or without swivel joints, including fixing to steel pipe or union, complete all as specified and directed. |
| 117 | S&F PVC (SWR) 75mm dia floor trap, plain with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed. |
| 118 | S & F PVC (SWR) gully trap 125/110mm setting and jointing with solvent cement as fixed in repairs complete all as specified and directed. |
| 119 | M&L for Rectification of water leakage from kitchen sink/wash basin area, including detection of source, dismantling and replacement of defective pipes, traps and fittings, jointing, testing, and making good the disturbed surfaces, complete all as specified and directed. |
| 120 | Providing and laying of water proofing treatment to sunken portion including vertical portion by applying cement slurry make with acrylic based polymer modify cementeneuous composite compound and including demolition and filling of sunken floor with and including PCC 1:5:10 type E2 (Using 40mm brick aggregate) complete all as specified and directed.(a) First layer of slurry of cement @ 0.488 Kg/sqm with acrylic based polymer modify cementeneuous composite compound @ 0.28Kg/sqm. This layer allowed to air cure for 4 hours. (b) Second layer of cement slurry @ 0.242kg/sqm mixed with acrylic based polymer modify cementeneuous composite compound @ 0.125kg/sqm. This layer allowed to air cure for 4 hours. (c) The slope shall be 1:20 towards the corner of outer wall and GI pipe of 50mm dia (medium grade) be inserted at corner projecting out side 20cm. (d) 15mm thick plaster in CM 1:3 mixed with WPC to be provided while concrete on green. (e) Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 Kg per sqm including bitumen primer @ 0.4Kg/Sqm, complete all as specified and directed. (f) APP modified membrane 3mm thick and weighing not less than 3 kg/sqm with 160 GSM/sqm, non woven polyester mat as center core reinforcement, laid with 75 mm side over lap and 100mm end over lap, the membrane has to be laid with LPG tourch and over lap sealed and finished neat over roof including a coat of bitumen 85/25 at the rate of 1.2 Kg per sqm over APP membrane, complete all as specified and directed. (e) Joints of trap WC/Soil pipes shall be properly sealed with sealing compoundNote : (I) Concrete for sunken slabs shall be mixted with water proofing compound (WPC) as per manufactures instructions. Before carrying out water proofing treatment the sunken shall be tested with water for 48 hours for any leakage/dampness is seen in ceiling below. then treatment is again carried out to RCC slab and it is again tested before passing for next stage. (II) Only floor area shall be measured for payment purpose |
| 121 | Demolition of cement concrete (unreinforced) as in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed. |
| 122 | M&L Providing, cement concrete 1:2:4 type B-0 (12.5mm graded aggregate ) as in roof kerbs or mud stops, rounded or chamfered on edges or as in padding concrete complete all as specified and directed. |
| 123 | M&L and taking down of existing unserviceable roof treatment materials and PCC/CM/Brick tiles padding etc from top of roof upto slab (complete depth) carefully by cutting chiseling, cleaning the surface by scraping brooming brushing etc and removing the rubbish from site exc. 500m but n exc 5.00 Km (Outside of MoD land) and applying roof treatment complete all as specified and directed with the following specifications:- (a) Rendering 10mm thick in CM 1:3 with water proofing compound on cleaned concrete surfaces of roof and finishing the surfaces fair and even including curing the plastered surfaces for 07 days by ponding of water over the roof (Levelling course). (Note : Water proofing compound shall be paid and measured separtely). (b) Applying evenly first coat cold bitumen primer confirming to IS-3384-1986 @ 0.40 Ltr per square metre on the cleaned plastered surfaces. (c) Applying evenly second coat of blown hot bitumen of grade 85/25 @ 1.20 kg per square metre (confirming to IS-702) on primed surfaces.(d) Applying third coat of APP modified membrane 3mm thick (minimum) and weight 3.60 Kg per square metre (reinforced) with polyster non woven fabric weighing not less than 150gms per square metre by torch application. The overlap shall not be less than 100mm on the transverse direction and 75mm on longitudinal direction respectively and sealing overlaps. |
| 124 | Applying one coat of aluminium paint on top of APP membrane complete all as specified and directed. |
| 125 | M&L for Cement concrete tiles 25cm x 25cm x 22mm thick, machine pressed (with grey cement & No pigment); set and jointed and pointed in neat cement slurry in floor etc over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 08, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Jul 22, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 13 daysJul 22, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 13 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender