Tender For special Repair Of Kote Building Number T-194 & 191 Of 4Th Battalion The Sikh Light Infantry At Him Yodha Military Station Sumdo Under Ge 863 Ews.
Tender Value
36.87 Lakhs
Estimated cost
Bid Submission
21 Jul 2026
15 days left
EMD
73740
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Lahul and Spiti → Himachal Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair Of Kote Building Number T-194 & 191 Of 4Th Battalion The Sikh Light Infantry At Him Yodha Military Station Sumdo Under Ge 863 Ews.
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of un-reinforced Cement Concrete of any description and in any position not otherwise specifically provided for. |
| 2 | M &L for 25 mm thick PCC 1:2:4 type BO (Using 12.5 mm graded stone aggregate) as in sub base in floors complete all as specified and directed by Engr-in-charge |
| 3 | M&L screed bed or bedding layer of morter 15 mm thick cement plaster 1:6 for laying floor finished to receive floor tiles/granite. |
| 4 | M&L for machine cut kota stone slab flooring 20-25mm thick mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed. |
| 5 | M&L PCC (1:3:6) type C-2 using 40mm graded stone agg 75mm thick as in plinth protection finished even and fair without using extra cement. |
| 6 | M&L for 75 mm thick cement concrete type D-2 (1:4:8) using 40 mm graded stone aggregate as in sub base under Chequered tiles. |
| 7 | M&L for chequered cement concrete tiles 20 cm by 20 cm by 25 mm thick with grey cement and pigments, set, jointed and pointed in neat cement slurry in floors complete all as specified and as directed. |
| 8 | Providing, cement concrete Type B1 1:2:4 (20 mm graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges |
| 9 | Dismantling plain or corrugated steel sheeting any gauge, thickness, including Naintal or similar pattern roof coverings |
| 10 | S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 11 | S&F Pre- painted galvatume aluminum zinc coating GI based plain sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 12 | S&F Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc complete all as specified and directed . |
| 13 | Taking down and Re-fixing of Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 14 | Dismantling structural steel work in cluding doors, gates but excluding framed truss etc complete all as specified and directed. |
| 15 | M&L Roof trusses (framed),trussed,purlins,crane gantries,rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including Fe 410-W (Gde E- 250) quality A complete all as specified . |
| 16 | S&F Framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing Fe 410 (Gde-E- 250) quality-A) complete |
| 17 | S&F 1.25mm thick mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required |
| 18 | M&L for preparation of new painted steel surfaces of any description, not otherwise described, over 10cm width or girth and applying two coat of synthetic enamel paint (first quality) complete all as specified and directed. |
| 19 | M&L for preparation of old painted steel surfaces of any description, not otherwise described, over 10cm width or girth and applying two coat of synthetic enamel paint (first quality) complete all as specified and directed. |
| 20 | Hacking out old broken glass (any thickness, size quality or description) from wooden frames or stone, concrete or brick surrounds glazed with putty or fixed with beads complete all as specified & directed. |
| 21 | S&F 3mm thick glass sheet any size oridinary qlty in steel or wooden frames complete with fixing materials such as putty glazing pins wooden beads etc. |
| 22 | Demolition of precast concrete block walling built in cement morter complete all as directed. |
| 23 | M&L for precast cement concrete block masonary walling type C-I 1:3:6 using 20mm graded aggregate with solid blocks, exc. 10 cm in width and setting in CM 1:6 complete. |
| 24 | Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed. |
| 25 | M/L for PCC 1:2:4 type B1, using 20mm graded stone aggregated as in plinth band, lintel band, roof band , lintel bands ,copings and other similar bands etc Complete all as specified and directed. |
| 26 | M & L for rendering 15mm thick in cement plaster 1:4 on stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing finishing even and smooth without using extra cement complete all as specified and directed. |
| 27 | M & L for preparation of new plastered surface of wall and applying two coats of cement base paint over a coat of alkali resistant priming paint complete all as specified and directed. |
| 28 | Taking down shutters of any description area exc 1 sqm and n exc 2 sqm each complete all as specified & directed. |
| 29 | S & F 35mm second class hard wood Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed. |
| 30 | S&F 300mm long aluminium anodised sliding door bolts , plate type ,stove enameled black , with bright bolt not less than 12mm dia with and incl minimum of 6 bolts and nuts ,four on bolt plate and two on staple. |
| 31 | S&F 100mm long Aluminium butt hinges of extruded aluminium alloy with galvanized mild steel hinge , pin anodized complete all as specified |
| 32 | S&F 150mm long aluminium anodised handle fabricated type complete all as specified and as directed by Engineer-In-Charge. |
| 33 | S&F 150mm long aluminium anodized barrel tower bolt of extruded section complete all as specified and directed by Engineer-In-Charge. |
| 34 | M&L for galvanised M S Wire cloth of 0.56 mm nominal dia of wire and average width of aparture 1.18 mm fixed with tinned tack for galvanized wire staple complete all as specified & directed. |
| 35 | S and F Steel windows for industrial buildings, fixed type, with glazing bars complete all as specified |
| 36 | Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/ blankets, any thickness inclduding cover fillets.complete all as specified and directed by Engr-in-charge. |
| 37 | Dismantling timber scantlings 40 sq.cm and over in section, in any positions as in framed work.complete all as specified and directed by Engr-in-charge. |
| 38 | M&L 2nd class hard wood in scantling timber framed work fixed clean sawn directed complete all as specified and directed by Engr-in-charge. |
| 39 | M&L 6 mm thick decorative veneered decorative plywood,grade 1 (with BWR resin) with decorative face veneers on one faces fixed with screws to timber frame workith screws to timber frame work in ceiling etc complete all as specified and as directed. |
| 40 | M&L for 9 mm thick decorative veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one faces fixed with screws to timber frame work as in wall pannelling/ceiling/cup board shutters complete all as specified & directed. |
| 41 | S & F Second class hard wood plain fillets, wrought, square, rectangular or triangular in section, secured with screws, cross sectional area exceeding 3 and not exceeding 6 Sq. cm |
| 42 | M&l for PCC (1:3:6) type C2 using 40mm graded crushed stone aggregate as in foundation filling and mass concrete complete all as specified and directed. |
| 43 | Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground complete all as specified and directed. |
| 44 | S&F angle iron section with swain neck as in fencing posts struts including notching drilling holes for wire mesh etc and flat iron fillets for securing wire mesh etc including all necessary drilling, bolting or riveting and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed. |
| 45 | S&F Mild steel Deformed or twisted bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 46 | Dismantling fencing wire mesh, any type complete all as specified and directed. |
| 47 | S&F Chain link MS galvanisd fencing, any size of mesh 50mm x 50mm and dia of wire 3mm complete all as specified and directed. |
| 48 | Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed. |
| 49 | S&F Mild steel rag or lewis bolts, screwed one end, with hexagonal or square nuts and washers 12mm dia and 100mm long, the other end enlarged and jagged or lewised, n exc 15cm longcomplete all as specified and directed. |
| 50 | Excavation in trenches n exc 1.5m wide and n exc 1.5 m deep and getting out in any type of soil |
| 51 | Returning filling in incl spreading levelling watering and well ramming in layers n exc 25cm thickness |
| 52 | Removing excavated soil to a distance n exc 50m and depositing at alevel n exc 1.5m above the starting point |
| 53 | Cutting in to existing manholes for forming new drains and making good to pipe and making good to pipe and rendering ,cutting out existing benching in cement conc 1:2:4 type B1(in 1/2 or 3/4 round in section)and reforming benching as reqd for 150mm bore pipe. |
| 54 | Demolition and breaking up drain pipes (Salt glazed ware, AC or reinforced concrete) set in cement mortar including the pipe 150mm dia inserted in Man holes walls etc including removal of rubbish outside of MD land. |
| 55 | M&L for conc 1:4:8 type C2 using 40mm graded aggregateas in bed to 150mm drain pies incl packing under and haunching against the sides pipesafter they are laid and tested for |
| 56 | S&F salt glazed stone ware drain pipe 150mm bore in trenches and jointed as spfd |
| 57 | M&L PCC 1:2:4 type B1 using 20mm graded aggregates for precast cement conc slabs as in manhole covers set in cement mortar1:4 including demolition / taking up of existing cover slabs & removing rubbish outside MD land. |
| 58 | M&L for mild steel steel TMT bars 10MM dia and over cut to length bent to shape reqd ,incl cranking ,bending spirally for hooping columns hooking ends and binding with mild steel wire annealed not less than 0.9 mm dia |
| 59 | M&L for mild steel steel TMT bars 6mm to 8mm dia and over cut to length bent to shape reqd ,incl cranking ,bending spirally for hooping columns hooking ends and binding with mild steel wire annealed not less than 0.9 mm dia |
| 60 | M&L for extra for forming fair finished drain or channel 30cm nner girth in cement concrete ,using extra cement ,incl forms moulds ,mitered ends etc |
| 61 | Demolition of reinforced cement concrete cover slab for MH/Spetic tank and removing the debris to a distance not exc 500 M as directed. |
| 62 | M&L for reinforced cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone graded aggregatework as in slabs supported on walls , beams etc |
| 63 | M&L for form work to soffits of suspended slabs and similar work not exceeding 200mm thick |
| 64 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, , pendents, regulators sockets, light fittings , holder, bell push, ding dong etc. removing materials to store for keeping in safe custody or for taking credit ( credit for above items should be made as per conditions separately ) and making good disturbed suefaces of walls, floor etc. |
| 65 | M&L for point wiring using approved colour coding as per IS with using 1.5 Sqmm multistranded,1100 volt grade copper conductor cable of PVC insulated and unsheathed type alongwith 1.5 Sqmm PVC insulated standed copper conductor cable for continuous earthing in & incl PVC casing & capping with accessories having ISI mark fixed on wall surfaces / ceiling including provision of 2 mm thick sheet metal terminal box with 3 mm thick hylam laminated sheet on top for fixing modular switches sockets etc. all as specified for one light point/ fan Bell point controlled by one switch complete all as specified and directed by Engineer-in-Charge. |
| 66 | All as per Srl item No 65 here-in-before but controlled with one 3 pin socket outlet 5 Amp, independent board with other switches with cable 1.5 Sqmm complete all as per specified and directed by Engineer-in-Charge. |
| 67 | All as per srl item no 65 here-in-before but controlled with one 3 pin socket 15 Amp on the independent board with other switches with cables 2.5 Sqmm complete all as specified and directed by Engineer-in-Charge. |
| 68 | Supply and fixing of socket outlet 5 Amp, 230 Volt, flush button single pole one way complete all as specified and directed by Engineer -in-Charge, |
| 69 | Supply and fixing of switch Piano type 5 Amp, 230 Volt, flush button single pole one way complete all as specified and directed by Engineer -in-Charge. |
| 70 | Supply and fixing of switch Piano type 15 Amp, 230 Volt, flush button single pole one way complete all as specified and directed by Engineer -in-Charge. |
| 71 | Supply and fixing of socket outlet 15 Amp, 230 Volt, flush button single pole one way complete all as specified and directed by Engineer -in-Charge, |
| 72 | Supply and fixing in replacement LED integrated batten tube light fittings 20W 4 Feet long complete with twin core twisted flexible copper conductor cable complete all as specfied and directed. |
| 73 | M&L Ceiling rose, 3 terminal with ISI mark all as specified and directed by Engr-In-Charge. Make :ANCHOR or equivalent. |
| 74 | Supply and fixing LED Lamp 12 Watt in lamp (bulb) & holder complete all as specified and directed. |
| 75 | Supply and fix Bajaj LED Bulk head light fittings, 10 W cool white, color temperature 3500-4100K wall mounting type complete all as specifed and directed of equavalent make : CG/Philips/wipro etc. |
| 76 | Supply and fixing in replacement of sheet metal enclosure double door for DBs single pole and neutral for 8 way 240 volt complete all as specified and direct by Engineer-in-Charge . |
| 77 | Supply and fixing in replacement of miniature circuit breaker (MCB) SPN 40 to 63 AMP rating 240V, 10KA 'C' curve in the MCB DB complete with connection testing and commissioning |
| 78 | Supply and fixing in replacement of 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 AMP, in the MCB DB Complete with connection testing and commissioning. |
| 79 | M & L in replacement for earthing complete with galvanised steel earth plate electrode 600x600x6.0 mm thicj\k buried directly in ground ( earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised iron wire of 4.0 mm dia as earth continuty conductor by means of bolts, nuts check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of SSR-I 2010, connected to main switch board all as specified and including testing on completion , necessary excation, earthwork, PCC works and GI earth pit cover with watering pipe 20 mm dia GI pipe medium grade , funeels with wire mesh and GI pipe of 15 mm dia of light grade for protection of earth wire upto 7.5 mtrs complete all as specified and directed by Engineer-in-Charge. Note:- On testing after completion if the desired resistance is not obtained the earthing shall be re- done aat no extra cost. |
| 80 | Supply and fixing in replacement of 1100 Volts grade heavy duty cable PVC insulated aluminium stranded conductor served with inner sheathing of PVC tape and overall PVC sheathed in service connection suspended by insulating hangers not more than 1 meter apart including 4mm suspension wire one twin core cable flat or circular of size 10 Sqmm complete |
| 81 | Schedule of Credit Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 01, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 21, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 15 daysJul 28, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 22 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender