Tender For Repair Works In The Pems Academic Blocks A, B, C And D At Iiitdm Kancheepuram
Tender Value
Ref. Documents
Estimated cost
Bid Submission
21 Jul 2026
9 days left
EMD
4.50 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Chengalpattu → Tamil Nadu
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair Works In The Pems Academic Blocks A, B, C And D At Iiitdm Kancheepuram
BOQ
| Sl. No. | Item Description |
| 1 | Removing and refixing precoated galvanised puffing profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x125 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 2 | Providing and fixing 50 mm thick factory-made PUF (Polyurethane Foam) insulated roofing panels with outer and inner facings of precoated galvanised iron/steel sheets of 0.50 mm (±0.05 mm) thickness each, conforming to IS: 277 with minimum 120 GSM zinc coating and 240 MPa steel grade, having 5–7 microns epoxy primer on both sides and 15–18 microns polyester top coat on exposed surface, including back coat as per manufacturer’s specification, and supplied with minimum 25 microns protective guard film to prevent damage during transportation and erection; the insulation core shall be rigid PUF of 50 mm thickness, density 40 ± 2 kg/m³ and thermal conductivity not exceeding 0.023 W/mK, factory injected to ensure proper bonding with steel facings, with panel effective cover width about 1000 mm (overall width about 1060 mm) and supplied in single lengths up to 12 m or as required; |
| 3 | the panels shall be fixed in position over prepared supporting framework using self-drilling/self-tapping screws of size 10 mm dia × 110 mm length with EPDM washers/seals ensuring complete watertightness, including necessary side/end laps, alignment, cutting, trimming and fixing for all heights and in horizontal, vertical or curved surfaces as per directions of Engineer-in-charge, complete in all respects, excluding the cost of purlins, rafters, trusses and structural supports, but including all materials, labour, tools and tackles required .Make: Jindal /JSW / ESSAR |
| 4 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :Make: JSW / ESSAR |
| 5 | Ridges plain (500 - 600mm) |
| 6 | Flashings/ Aprons.( Upto 600 mm) |
| 7 | Barge board (Upto 300 mm) |
| 8 | Providing and fixing 15 cm wide, 45 cm overall semi-circular plain G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete.Make: JSW / ESSAR |
| 9 | 0.80 mm thick with zinc coating not less than 275 gm/m² |
| 10 | Providing valleys of 90 cm wide overall in plain G.S. sheet fixed with polymer coated J, or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete :Make: : JSW / ESSAR |
| 11 | 1.60 mm thick with zinc coating not less than 350 gm/m² |
| 12 | Extra for providing and fixing wind ties of 40x 6 mm flat iron section. |
| 13 | Fixing of old wind tie with new fittings including painting two or more coats with anticorrosive bitumastic paint of approved brand & manufacturer over and including priming coat of ready mixed zinc chromate yellow primer of approved brand.Make: Asian paint / ICI dulex / Neroloc Paints Ltd |
| 14 | Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3 mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufactured of density at 25°C, 0.87 - 0.89 kg/litre and viscocity 70 - 160 cps. Over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 350/300 N/5 cm.Tear strength in longitudinal and transverse direction as 60/80N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane :Make:Sika / Fosroc / Dr. Fixit / STP / Asian Paints |
| 15 | 3 mm thick |
| 16 | Painting with aluminium paint of approved brand and manufacture to give an even shade .Make: Asian Paints / Ferrous Crete (India) Pvt. Ltd. |
| 17 | Two or more coats on new work |
| 18 | Providing & Applying weather proof sealant on outer joints of approved make confirming to IS & directed by Engineer-in-charge.Make: Dow corning India / GE Silicones |
| 19 | Sealant 25mmx10mm at joints |
| 20 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. |
| 21 | Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge. |
| 22 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at |
| 23 | 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm |
| 24 | at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cut-outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :Make: Arm strong / Saint Gobain |
| 25 | 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) with Required Number of Trap door for electrical access. |
| 26 | Providing and fixing 8 mm thick pre-laminated cement bonded wood particle board conforming to IS: 15786:2008, of approved brand and shade, with decorative lamination on one face and balancing lamination on the other face, for wall side covering under roof/eaves, fixed to existing structural members/wall surface using C.P. brass / stainless steel screws with suitable washers, including necessary cutting, drilling, edge finishing, jointing, providing backing supports wherever required, and sealing of joints with approved sealant to ensure proper alignment and neat finish, complete in all respects with all materials, labour, tools and tackles, as per architectural drawings and directions of the Engineer-in-charge.Make:Bison panel / Saint-Gobain (Gyproc) / Knauf / Everest |
| 27 | Post construction anti termite treatment by injecting chemicals of approved brand and as per the directions of Engineer-in-charge .Make: NOBAN / PIRAMID |
| 28 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) :Make: Hindalco / Jindal / Bhoruka |
| 29 | For fixed portion |
| 30 | Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) |
| 31 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)Make: Hindalco / Jindal / Bhoruka |
| 32 | Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) |
| 33 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):Make: Saint Gobain / Modiguard |
| 34 | With float glass panes of 6 mm thickness (weight not less than 12.50 kg/sqm) |
| 35 | With Tinted float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) |
| 36 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :Make : Sigma / Jyothi |
| 37 | 125 mm Make : ISI Standard |
| 38 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 39 | 200x10 mm. Make : ISI Standard |
| 40 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screwsetc. complete. |
| 41 | Twin rubber stopper |
| 42 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :Make : Sigma / Jyothi / Everite |
| 43 | 300x16 mm |
| 44 | Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer in-charge complete.Make : Earl Bihari / KINLONG |
| 45 | 355 X 19 mm |
| 46 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:Make : Greenlam / Kitply / Century |
| 47 | 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 48 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White,Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete.Make : Asian / Somany / Kajaria |
| 49 | Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.Make : Asian / Somany / Kajaria |
| 50 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.Make : Ultratech/ Chettinad/Dalmia |
| 51 | 40 mm thick with 20 mm nominal size stone aggregate |
| 52 | Repair to plaster of thickness 12 mm to 20 mm in patches of area 2.5 csqm and under, including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with white cement based polymer modified self curing mortar, including disposal of rubbish, all complete as per the direction of Engineer-In-Charge.Make : Ultratech/ Ramco / Dalmia |
| 53 | Removing rust and corrosion of existing structural steel member by scrapping, sand papering and preparing the surface smooth including etc. complete.at all heights as per the direction of Engineer in charge |
| 54 | Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete |
| 55 | Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.Make : Asian Paints / Nerolac Paints / Berger Paints |
| 56 | On steel work |
| 57 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Make : Asian paints / Nerolac Paints / Berger Paints |
| 58 | One or more coats on old work |
| 59 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.Make : Asian paints / J.K.wall putty / Birla wall care |
| 60 | Applying priming coats with primer of approved brand an manufacture, having low VOC (Volatile Organic Compound ) content.Make : Asian paints / JK Primaxx / Berger Paints |
| 61 | With water thinnable cement primer on wall surfacehaving VOC content less than 50 grams/litre |
| 62 | Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.Make : Asian paints / NerolacPaints / Berger Paints |
| 63 | Two coats |
| 64 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shadeMake : Asian paints / NerolacPaints / Berger Paints |
| 65 | Old work (Two or more coats applied @ 1.43 ltr/ 10 sqm)over existing cement paint surface |
| 66 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.Make : Parryware / Supreme |
| 67 | 10 litre capacity - White |
| 68 | Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour.Make : Parryware / Supreme |
| 69 | 15 mm nominal bore with 45 cm length |
| 70 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 71 | Flexible pipe |
| 72 | 40 mm dia |
| 73 | Providing and fixing CP Brass pillar cock 15mm nominal bore of approved quality & make and as per the direction of Engineer-in-charge. |
| 74 | Providing and fixing brass long body bib cock of approved quality :Make : Jaquar / Parryware / Metro |
| 75 | 15 mm nominal bore |
| 76 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931Make : Jaquar / Parryware / Metro |
| 77 | 15mm nominal bore |
| 78 | Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in- Charge. |
| 79 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:Make :Hindware / Parryware / Kohler |
| 80 | White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 81 | Providing and fixing solid plastic seat with lid for pedestal type W.C.pan complete :Make :Hindware / Parryware / Kohler |
| 82 | White solid plastic seat with lid |
| 83 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe withclamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints completeas per direction of Engineer in Charge.Internal work - Exposed on wallMake : Supreme / Finolex / Ashirwad |
| 84 | 25 mm nominal dia Pipes |
| 85 | Making connection of CPVC pipe distribution branch with CPVC. main of following sizes by providing and fixing tee, including cutting and fixing the pipe etc. complete :Make: Supreme / Finolex / Ashirwad |
| 86 | 25 to 40 mm nominal bore |
| 87 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,(i) Single socketed pipes.Make: Supreme / Finolex / Astral |
| 88 | 75 mm diameter |
| 89 | 110 mm diameter |
| 90 | Providing and fixing CP brass push cock including CP brass urinal spreader and CP brass connection, dismantling the old urinal and making good the same, etc., complete as directed by the Engineer-in-charge.Make : Jaquar / Parryware / Metro |
| 91 | 15 mm nominal bore |
| 92 | Providing and fixing 600x450 mm beveled edge mirror of superiorglass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.Make : Modi Guard / Saint Gobain |
| 93 | Providing and fixing SS Grating Circular type with openable circular lidMake : ISI Standard |
| 94 | 125 mm nominal dia with 25 mm waste hole |
| 95 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm size respectively. Make : ISI Standard. |
| 96 | Providing and fixing of Health faucet with connection hose for the European type water closet with necessary hardware accessories,tools complete as per the directions of Engineer-in-charge Make : Parryare / Prayag |
| 97 | Providing & fixing prefinished ,pre-moulded granite stone strips size of 50mm width and 18mm thick with both side nosing to door sill with epoxy resin based adhesive including necessary cleaning,hardwares and labour etc.complete all as per directions of Engineer -in- charge.Make : Asian Granite India Ltd |
| 98 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: |
| 99 | All kinds of soil |
| 100 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift. |
| 101 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :Make :Chettinadu cement / Ultra Tech /Dalmia |
| 102 | 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 103 | Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand).Make :Chettinadu cement / Ultra Tech /Dalmia |
| 104 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation,levelling & dressing & finishing the top smooth.Make :Chettinadu cement / Ultra Tech /Dalmia |
| 105 | Centering and shuttering including strutting, propping etc. and removal of form work for : |
| 106 | Suspended floors, roofs, landings, balconies and access platform |
| 107 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Make : SAIL /JSW /TATA |
| 108 | Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 109 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :Make : Chettinadu cement / Ultratech cement |
| 110 | 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 111 | 12 mm cement plaster of mix :Make :Chettinadu cement / UltraTech /Dalmia |
| 112 | 1:6 (1 cement: 6 fine sand) |
| 113 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Make :Chettinadu cement / UltraTech /Dalmia |
| 114 | Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 115 | Laying old cement concrete interlocking paver blocks of any design/ shape laid in required line, level, curvature, colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineerin- charge. (Old CC paver blocks shall be supplied by the department free of cost). |
| 116 | Removing and Refixing overhead/terrace PVC water storage tank of any size from water supply line laying and fixing with tank nipple including etc. complete at all heights as per direction of Engineer-in-charge. |
| 117 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.Brand: Sintex/Supreme/ Ashirvad |
| 118 | Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc at all heights. including dismembering and stacking within 50 metres lead. |
| 119 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.Make: JSW / Tata / SAIL |
| 120 | In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete at all heights |
| 121 | In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 122 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :Make: Zoloto / Leader |
| 123 | 50 mm nominal bore |
| 124 | Supply, drawing, termination and testing of following sizes of FRLS or FRLSH, PVC insulted multistranded copper conductor wire should be inline with the incoming phase colour, 1.1KV grade in existing surface/ recess/ PVC conduits, including floor cutting & finishing by placing of all the accessories & lugs as per the requirement complete etc.,Make: Finolex/ Polycab/ RR kabel/ Havells |
| 125 | 1 Run x 1.5 Sq.mm (1-ph) |
| 126 | Red/Yellow/Blue |
| 127 | Black |
| 128 | Green |
| 129 | 1 Run x 2.5 Sq.mm (1-ph) |
| 130 | Red/Yellow/Blue |
| 131 | Black |
| 132 | Green |
| 133 | 1 Run x 4.0 Sq.mm (1-ph) |
| 134 | Red/Yellow/Blue |
| 135 | Black |
| 136 | Green |
| 137 | Supply & drawing of 1\\" size PVC cum metallic flexible hose (Heavy duty) for wires with required all accessories etc., ISI marked |
| 138 | Supply & drawing of 1\\" size PVC ordinary hose for wires with required all accessories etc., ISI marked |
| 139 | Supplying, fixing, testing and commissioning of the following suitable size modular type PVC box, plate, cover, switch, socket and connections etc.in the wall/surface/recess with wooden planks, including wood / table cutting and making good etc., as required. Make: Legrand-Myrius/ Crabtree-Thames |
| 140 | 6 module PVC box with modular plate, cover and box in front on surface or in recess or in wooden/metal table, including providing and fixing etc. |
| 141 | 8 module PVC box with modular plate, cover and box in front on surface or in recess or in wooden/metal table, including providing and fixing etc. |
| 142 | 12 module PVC box with modular plate, cover and box in front on surface or in recess or in wooden/metal table, including providing and fixing etc. |
| 143 | 1 No. of 5/6A rating modular switch including connections etc., as required. |
| 144 | 1 No. of 3 pin, 5/6A rating modular socket outlet including connections etc., as required. |
| 145 | 1 No. of 15/16A rating modular switch including connections etc., as required. |
| 146 | 1 No. of 6 pin, 15/16A rating modular socket outlet including connections etc., as required. |
| 147 | Supply and fixing of 100 watt, 2 module, 5 stepped electronic fan regulator including connections etc., as required Make: Legrand -Myrius / Crabtree-Thames |
| 148 | Supply and fixing of 32 mm x 20 mm size PVC cable management with required necessary fixing requirements like bends, couplers, joints, end caps etc., as required. Make: Legrand/ MK |
| 149 | Supply and fixing of 50 mm x 50 mm size PVC cable management with required necessary fixing requirements like bends, couplers, joints, end caps etc., as required. Make: Legrand/ MK |
| 150 | Supply and fixing of 100 mm x 50 mm size PVC cable management with required necessary fixing requirements like bends, couplers, joints, end caps etc., as required. Make: Legrand/ MK |
| 151 | Supply and fixing of 4 feet, 20 watt cool white LED battenMake: Philips/ Havells/ Crompton |
| 152 | Supply and fixing of 15\\" metal Exhaust fan with louvers and safety grill as required.Make: Bajaj/ Crompton/ Havells |
| 153 | SITC of 1200 mm sweep ceiling fan (Brown colour) of BEE minimum '3' star rated energy efficient, 210 CMM with 1 feet down rod, wiring, safety rope, canopy set, clamp set, bolt, nut & fastners etc including removing of existing ceiling fan, cutting & refinishing in the existing wall/ tile/ metal sheet etc., as required.Fan make: Havells/ Bajaj/ Crompton |
| 154 | Supply & fixing of Hylam sheet including fixing etc., as required |
| 155 | Supply and fixing of required size PVC round sheet to pack wherever required |
| 156 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.Make: Precision/Avonplast/Anchor/Modi |
| 157 | 20 mm |
| 158 | 25 mm |
| 159 | 32 mm |
| 160 | 40 mm |
| 161 | Supply of 3.5 Core * 240 Sq. mm PVC sheathed, PVC insulated, XLPE armoured, Aluminum conductor cable of 1.1 kV grade suitable for outdoor applications as per IS 7098 and It's amendments upto date as required.Make: Polycab/ Havells/ Finolex |
| 162 | Supplying and laying of 120 mm dia (OD-120 mm & ID-103 mm nominal) size DWC HDPE pipe ISI marked along with all acceossories like socket, bend, couplers etc., conforming to IS 14930, Part II complete with fitting and cutting, jointing etc., direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. |
| 163 | Laying of one number PVC insulated and PVC sheathed/ XLPE power cable of 1.1 Kv grade of 3.5 core * 240 sq. mm size in the existing RCC/ HUME/ METAL/DWC pipe as required. |
| 164 | Supplying and making end termination with brass compression gland and aluminium lugs for 3.5 core * 240 sq.mm (62 mm) of PVC insulated and PVC sheathed/ XLPE aluminium conductor cable of 1.1 KV grade as required |
| 165 | Supply & fixing of 315 Amps C-line On Load manual change over switch (COS) disconnector '2' I/P, '1' O/P, with extendable spreader terminals suitable to connect 2 numbers of 3.5 core * 240 sq. mm at incomer side, Indoor suitable, wall mount type, panel enclosure with 1.6 mm thick CR sheet of powder coated along with Extended Rotary Handle, terminal shrouds, phase barriers etc., as required including necessary accessories to fix on the wall and other electrical connections as per the directions of Engineer-In-Charge.TPN SDFU Make: Legrand /L&K/ Siemens/ Schneider/ ABB |
| 166 | Supplying and drawing following sizes of FRLS PVC insulated, XLPE armoured copper conductor cable as per IS 7098 in the existing surface/ recessed steel/ PVC conduit including clamps etc., as required.Make: Polycab/ Havells/ Finolex |
| 167 | 4 * 50 sq.mm + 2 * 16 sq.mm earth wire |
| 168 | 4 * 16 sq.mm + 2 * 6 sq.mm earth wire |
| 169 | Supply, drawing, termination and testing of following sizes of FRLS or FRLSH, PVC insulted multistranded copper conductor wire should be inline with the incoming phase colour, 1.1KV grade in existing surface/ recess/ PVC conduits, including floor cutting & finishing by placing of all the accessories & lugs as per the requirement complete etc.,Make: Finolex/ Polycab/ RR kabel/ Havells |
| 170 | 1 Run x 4 Sq.mm (3-ph) |
| 171 | Yellow |
| 172 | Black |
| 173 | Green |
| 174 | 1 Run x 6.0 Sq.mm (3-ph) |
| 175 | Yellow |
| 176 | Black |
| 177 | Green |
| 178 | 1 Run x 4.0 Sq.mm (1-ph) |
| 179 | Red/Yellow/Blue |
| 180 | Black |
| 181 | Green |
| 182 | Supply and fixing of following ways surface/ recess mounting, vertical type, 415 Volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required.Make: Legrand /L&K/ Siemens/ Schneider/ ABB |
| 183 | 12 way (8+36), Double door |
| 184 | Suppling and fixing of following rating, 240/415 Volts, 10kA, \\"C\\" Curve, miniature circuit breaker/ isolator/ residual current circuit breaker suitable for inductive load of following poles in the above DB complete with connections, testing and commissioning etc., as required.Make: Legrand /L&K/ Siemens/ Schneider/ ABB |
| 185 | Four pole, 125 Amps, 415 Volts, Isolator |
| 186 | Triple pole and neutral, 63 Amps, 100 mA, 415 Volts, RCCB |
| 187 | Triple pole, 32 Amps, 415 Volts, MCB |
| 188 | Triple pole, 20 Amps, 415 Volts, MCB |
| 189 | Supplying and fixing following way, 7 segment, 3 phase input, single phase output, horizontal type, sheet steel, MCB distribution board, 415 Volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc., as required. (But without MCB/ RCCB/ Isolator).Make: Legrand /L&K/ Siemens/ Schneider/ ABB |
| 190 | 6 way (4+18), Double door |
| 191 | Suppling and fixing of following rating, 240/ 415 Volts, 10kA, \\"C\\" Curve, miniature circuit breaker/ isolator/ residual current circuit breaker suitable for inductive load of following poles in the above DB complete with connections, testing and commissioning etc., as required.Make: Legrand /L&K/ Siemens/ Schneider/ ABB |
| 192 | Triple pole and neutral, 63 Amps, 415 Volts, MCB |
| 193 | Single phase and neutral, 63 Amps, 30 mA, 240 Volts, RCCB |
| 194 | Single pole, 20 Amps, 240 Volts, MCB |
| 195 | Single pole, 16 Amps, 240 Volts, MCB |
| 196 | Single pole, 10 Amps, 240 Volts, MCB |
| 197 | Supplying and fixing 20 Amps, 240 Volts, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top along with 20 Amps, \\"C\\" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc., as required.Make: Legrand /L&K/ Siemens/ Schneider/ ABB |
| 198 | Supplying and fixing 20 Amps, 415 Volts, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top along with 20 Amps, \\"C\\" curve, TP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc., as required.Make: Legrand /L&K/ Siemens/ Schneider/ ABB |
| 199 | Supplying and fixing 30 Amps, 415 Volts, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top along with 20 Amps, \\"C\\" curve, TP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc., as required.Make: Legrand /L&K/ Siemens/ Schneider/ ABB Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 01, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 21, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 9 daysJul 22, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 10 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender