Tender For Replacing Of Damaged Panelled & Flush Doors In Various Blocks Of Shakti Bhawan Along With Providing & Fixing Of M.S. Wire Gauge Shutter In Sequrity Office Of Mppmcl, Jabalpur.
Tender Value
1.95 Lakhs
Estimated cost
Bid Submission
15 Jul 2026
12 days left
EMD
2000
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jabalpur → Madhya Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Replacing Of Damaged Panelled & Flush Doors In Various Blocks Of Shakti Bhawan Along With Providing & Fixing Of M.S. Wire Gauge Shutter In Sequrity Office Of Mppmcl, Jabalpur.
BOQ
| Sl. No. | Item Description |
| 1 | SOR No.15.6.3:-Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal ofunserviceable material within 50 metres lead as per direction of Engineer-in- Charge. In cement mortar. |
| 2 | SOR Item No.15.48:- Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 3 | NSOR Item No. 15.14.2:- Dismantling doors,windows and clerestory windows (steelor wood) shutter including chowkhats, architrave, holdfastsetc. complete and stacking within 50 metres lead :Of area beyond 3 sq. metres |
| 4 | SOR Item No. 15.14.1 :-Dismantling doors,windows and clerestory windows (steel or wood)shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below. |
| 5 | SOR Item No. 9.1.2 :-Providing wood work in frames of doors,windows, clerestory windows and other frames, wrought framed and fixed inposition with hold fast lugs or with dash fasteners of required dia and length (holdfast lugs or dash fastener shall be paid forseparately).Sal wood |
| 6 | SOR Item No. 9.5.1.1 :-Providing and fixing panelled or panelledand glazed shutters for doors, windows and clerestory windows including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws excluding, panelling/glazing which will be paid for separately, all complete as perdirection of Engineer-in-charge Second class teak wood. 35 mm thick shutters |
| 7 | SOR Item No. 9.6.1 :-Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick :Second class teak wood |
| 8 | SOR Item No. 9.6.8 :-Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick :Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. Wire and 1.4 mm wide aperture with matching wood beading |
| 9 | SOR Item No. 9.19.2 :-Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.: 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. |
| 10 | SOR Item No. 9.58.3 :-Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 250x10 mm |
| 11 | SOR Item No. 9.95 :-Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701mm to 1000 mm) with double speed adjustment with necessary accessories and screws etc. complete. |
| 12 | SOR Item No. 9.83 :-Providing and fixing bright finished brass100 mm mortice latch and lock with 6 levers and a pair of lever handles with necessary screws etc. complete (best make of approved quality). |
| 13 | SOR Item No. 9.60.1 :-Providing and fixing ISI marked oxidised M.S. door latches conforming to IS:5930 with screws etc. complete: 300x20x6 mm |
| 14 | SOR Item No. 9.60.2 :-Providing and fixing ISI marked oxidised M.S. door latches conforming to IS:5930 with screws etc. complete: 250x20x6 mm |
| 15 | SOR Item No. 9.93 :-Providing and fixing Chromium plated brass hanging type floor door stopper with necessary screws, etc. complete |
| 16 | SOR Item No. 9.69.1 :-Providing and fixing ISI marked stainless steel handles with necessary screws etc. complete :125 mm |
| 17 | SOR Item No. 9.48 :-Providing 40x5 mm flat (iron hold fast 40 cm long) (0.628 kg) including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x 10x 15cm 1:3:6 mix (1 cement : 3 sand : 6 graded stone aggregate 20mm nominal size) |
| 18 | SOR Item No. 13.67.1 :-Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ litre |
| 19 | SOR Item No. 13.73 :-French spirit polishing: Two or more coats on new works including a coat of wood filler |
| 20 | SOR Item No. 9.21 :-Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). |
| 21 | SOR Item No. 6.4.2 :-Brick work with well burnt chimney bricks in bulls pattern trench kiln, crushing strength not less than 25kg/cm2 and water absorption not more than 20% in superstructure above plinth level and up to floor two level i/c curing etc complete. Cement Mortar 1:6 (1 cement : 6 sand) |
| 22 | SOR Item No. 13.2.2 :-15 mm cement plaster on the rough side of single or half brick wall of mix. 1:6 (1 cement : 6 sand) |
| 23 | SOR Item No. 13.41 :-Providing and applying white cement based putty of average thickness 1 mm, of approved brand over the plastered wall surface to prepare the surface even and smooth i/c all cost of material, labour and scaffold etc in all position complete. Note : Putty shall be applied only on the internal walls, for application on the exterior walls prior permission of Chief Engineer will be required. |
| 24 | SOR Item No. 13.46 :-Wall painting by any mechanical or manual means with plastic emulsion paint of approved brand and manufacture to give an even shade: Two or more coats on new work |
| 25 | SOR Item No. 10.26.2 :-Providing and fixing fly proof wire gauze to windows, clerestory windows and doors with M.S. Flat 15x3mm and nuts and bolts complete.Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides. |
| 26 | SOR Item No. 21.1.2.1 :-Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary -------------------- :For shutters of doors, windows and ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately). Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC15) |
| 27 | SOR Item No. 9.110.6 :-Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc complete:100x10 mm |
| 28 | SOR Item No. 9.108.8 :-Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to req colour or shade with necessary screws etc. complete: Note:- Aluminum hinges shall not be used in wooden shutters: 75x45x3.2 mm |
| 29 | SOR Item No. 9.113.3 :-Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: 75 mm Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 01, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 15, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 12 daysJul 16, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 13 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender