Tender For Construction Of Two Car Parking Sheds At Troops Line Sqae (A) & Lpr And Special Repair To Recovery Sand Butt (Bldg No P-48) At Long Range, Sqae (A) & Lpr, Khamaria Under Ge (P) No 1 Jabalpur
Tender Value
35.44 Lakhs
Estimated cost
Bid Submission
22 Jul 2026
14 days left
EMD
71000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jabalpur → Madhya Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Two Car Parking Sheds At Troops Line Sqae (A) & Lpr And Special Repair To Recovery Sand Butt (Bldg No P-48) At Long Range, Sqae (A) & Lpr, Khamaria Under Ge (P) No 1 Jabalpur
BOQ
| Sl. No. | Item Description |
| 1 | Excavation in post holes (or similar holes) each not exc. 0.50 Cum, getting out, returning, filling and ramming earth or broken rubble mixed with earth around in layers not exc. 25 cm watering and removing surplus soil to a distance not exc. 50 m and making good surface as in soft / loose soil complete all as specified and directed. |
| 2 | M & L for Moorum/raid bajri filling in floor or paving laid in layers not exceeding 15 cm thick, spread, leveled and remmed incl watering complete all as specified and directed. |
| 3 | M&L for Cement concrete type D-2 1:4:8 (using 40mm graded aggregate) as in foundation filling and mass concrete complete all as specified and directed. |
| 4 | S&F for steel work in tubular trusses incl special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 complete all as specified and directed. |
| 5 | M&L for two coats of synthetic enemel paint on new steel surfaces over one coat of red oxide primer over 10 cm width of girth incl preparation of surfaces complete all as specified and directed. |
| 6 | M&L for pre-painted galvalume aluminium zinc coating GI basied corrugated steel sheet 0.5mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed. |
| 7 | Surface excavation n.exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and directed |
| 8 | Removing excavated material for soft/loose soil exc. 250 m but nexc 500 m and depositing where directed complete all as specified and directed. |
| 9 | M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paver bloxk of M-35 grade ith approved colour, design & pattern as in tootparth, parks, lawns, drive ways or light traffic parking etc of required strength thichkness & shape/size made by table vibratory method usingPU mould, laid in required colour & pattern over and incl 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of interlocking paver blocks as per required size and pattern finishing and sweeping extra sand complete all as specified and directed. |
| 10 | M&L for PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in coping, kneesa, plinth bends, apex stone and similar works complete all as specified and directed. |
| 11 | M&L for sand filling under Target/ Butt including shape and size as per site/size of Butt complete all as specified and directed. |
| 12 | Dismantling of wrought iron and mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 13 | Erection and fixing only MS plates (plain or chequered ) channels, square cut or notched (ordinary and counter sunk) forming holes without any attachments, welding (as required all around) etc. complete all as specified and directed.Note - MS steel shall be reused retrived from item No. 12 above. |
| 14 | M&L for MS plates Fe 410 -W (Gde- E- 250) quality- A (plain or chequered ) chennals, square cut or notched (ordinary and counter sunk) forming holes without any attachments, including welding to join the plates as required all around and filling the gaps complete all as specified and directed. |
| 15 | S&F for Compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars,stiffeners, gusset plates, etc fixing of MS plate and like. complete all as specified and directed. |
| 16 | S&F for mild steel screw bolts (machine made) with hexagonal or square heads at one ends and screwed to other other or screwed both ends to be fitted washers and one hexagonal nut exc 15 cm and n exc 22.5 cm long dia 16 to 20 mm complete all as specified and directed. |
| 17 | Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed. |
| 18 | Dismantling of RCC in wall floors, roofs etc ground floor reinforcement cut as required to facilitate demolition complete all as specified and directed. |
| 19 | M&L for forming mortice holes, n exc. 50 cu cm for balusters, newels, rag-bolts, etc. and grouting with epoxy mortar including welding with fixing RCC where as required after balusters, etc. and fixing complete all as specified and directed. |
| 20 | M & L for RCC M-25 (Design Mix) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs and mass concrete complete all as specified and directed.Note:- Reinforcement shall be measured and paid separately under respective item. |
| 21 | M & L for RCC M-25 (Design Mix) as in walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings and buttresses complete all as specified and directed.Note:- Reinforcement shall be measured and paid separately under respective item. |
| 22 | M&L TMT bar 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. |
| 23 | M&L TMT bar 6 to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. |
| 24 | Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams; sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished surfaces of concrete, complete all as specified and directed. |
| 25 | Use and waste of formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter curved and rough finished surfaces of concrete, complete all as specified and directed. |
| 26 | M & L preparation of new steel surfaces of any description, over 10cm in width or girth & applying two coats of synthetic enamel paint over a coat of primer, complete all as specified and directed. |
| 27 | M & L for brickwork with subclass 'B' bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed. |
| 28 | M & L rendering 15mm thick on brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified and directed. |
| 29 | Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and directed. |
| 30 | M&L preparing plastered new surfaces of walls and applying three coats of white washing complete all as specified and directed. |
| 31 | Deduct schedule of credit amount Rs. 1,08,000.00 to be deducted during AOC Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 01, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 22, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 14 daysJul 29, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 21 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender