Tender For Supply Installation Testing and Commissioning of Liquid Waste Purification System (Including 05 Years Dlp And O&M) At M.B.S Hospital Kota
Tender Value
10.34 Crore
Estimated cost
Bid Submission
08 Jul 2026
6 days left
EMD
20.68 Lakhs
Bank guarantee accepted
Document Fee
7500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kota → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Supply Installation Testing and Commissioning of Liquid Waste Purification System (Including 05 Years Dlp And O&M) At M.B.S Hospital Kota
BOQ
| Sl. No. | Item Description |
| 1 | Part-A |
| 2 | DEVELOPMENT OF LIQUID WASTE PURIFICATION SYSTEM, CETP (Sewage Treatment Plant with Effluent Treatment ) |
| 3 | CETP WORK 1100 KLD (SEWAGE TREATMENT PLANT + EFFLUENT TREATMENT PLANT) |
| 4 | SUB HEAD: DEVELOPMENT OF LIQUID WASTE PURIFICATION SYSTEM, (CETP TYPE)} |
| 5 | Supply, Fabrication, installation, testing and commisioning of automatic sewage treatment plant with Effluent Treatment Plant based on MBR Process with sewage and Effluent handling capacity of 1100 KLD per day. The entire plant will be constructed in MSEP / JINK ALUMINIUM Febricated. The STP shall be designed as per Raw water, with necessary chemical dosing as required by the manufacturer's design. All the equipment, piping, pumps, air blowers and electrical panel etc. (CETP Make :- Willmer Eco Technologies/Eco vibe solutions Pvt Ltd) (Defect Liability Period will be 05 Years, All Parts and Machinery maintenance, Replacement included in 05 Year DLP) |
| 6 | Domestic Sewage from domestic Ward and Hospital toilets, kitchens etc. from the Commercial complex, Lab, OT, Labour Room Etc, and shall be discharged into the STP. Design to take consideration of same as Common Effluent Treatment Plant (C.E.T.P) |
| 7 | Daily average flow : 1100 M3/Day |
| 8 | PH : 6.5 - 8.5 |
| 9 | BOD5 : 250-300 mg/l |
| 10 | S. Solids : 200 - 450 mg/l |
| 11 | COD : 450-650 mg/l |
| 12 | Oil & Grease : 25-50 mg/L |
| 13 | Sewage discharge standard after treatment as per RPCB :- |
| 14 | PH : 7.0 - 8.5 |
| 15 | BOD5 : Less than 10 mg/l |
| 16 | TSS : Less than 10 mg/l |
| 17 | COD : Less than 50 mg/l |
| 18 | Oil & Grease : Less than 10 mg/l |
| 19 | Electro Machanical |
| 20 | 1100 KLD Sewage Treatment Plant Based MBR Technologies {Design to take consideration of same as Common Effluent Treatment Plant (C.E.T.P)} (STP Make :- Willmer Eco Technologies/Eco vibe solutions Pvt Ltd) |
| 21 | Corse Bar Screen :- SITC of two numbers of Manual Bar Screen, made out of 5 mm thick 40 mm SS Flat Bar, 20 mm Clear gap between two bars, Frame of screen to be made SS equal angle of 50 mm and support in middle of screen, Side Channel to install in Bar Screen Chamber with accessories, arrangement for removal and cleaning that is require to smooth working complete in all respect. Size: 800 x 1000 etc. complete as required. 2 Nos (Make :- Willmer Eco Technologies/Eco vibe solutions Pvt Ltd) |
| 22 | FineBar Screen :- SITC of Mechanical Fine Screen , mechanically for screening sewage. MOC SS, with accessories, arrangement for removal and cleaning that is require complete in all respect capable to handle the sewage flow 50-60 CUM/hr |
| 23 | Supply of vent pipes of 100 mm dia with mosquito proof grating suitable for the ventilation purpose of the various tanks |
| 24 | SITC of Floating/Submersible Aerator for Equalization Tank for equalizing and mixing of feed sewage BWS Make, Statically Balanced, Directly coupled three blade SS Impeller, with FRP constructed Float capable to handle motor, shaft and impeller Complete in all respect. Mixing dia approx 8 Meter, 5 HP 1440 RPM Motor. Make- Assurity/Toshio/CNP |
| 25 | EQUALIZED WASTE WATER TRANSFER PUMPS / RAW SEWAGE PUMP : 2 (1W + 1S) Nos. |
| 26 | Providing & fixing fully submersible sewage handling type pump for raw sewage transfer from equalization tank to aeration tank. The pump shall have complete CI construction, TEFC induction motor including pressure gauge, lifting arrangement for the pump. Solid handling shall be 25-40 mm. Make- Assurity/Toshio/CNP |
| 27 | Capacity : 55 M3/hr @ Discharge Head 10-15 M head (1 Working + 1 Standby), |
| 28 | Air Blower :- Diffusion system shall include the following: 2 (1W + 1S) Nos. |
| 29 | Tri Lobe type rotary air blowers 2 Nos. (1 W + 1 S) Capable of delivering 1100 cum/hr (each) of free air at 0.45 kg/cm2 driven through “V” belt or directly coupled through flexible coupling to a TEFC motor of suitable HP Suitable for 415 ± 10% volts, 3 phase, 50 cycles a/c supply for aeration of EQT, SHT and TWT. Make: Everest/Beta/Akash/Airvac/Eqvt. |
| 30 | Air piping :- shall comprise of pipes droppers/ laterals with MS C Class Header complete with all fittings such as tees, crosses, plugs, sockets, elbows, reducers, supports & clamps, puddle flanges etc cutting chases & making good in Plant Room. Make: Tata/Jindal/Supreme/Astral/Prince/Surya Prakash/Eqv. :- 1 Lot |
| 31 | Diffusers :- Fine /coarse aeration bubble diffusers as required. :- 1 Lot Make- Bharat Industries/PP Aqua/MM Aqua/Scogen/Pharmtech/ Vasu Enviro |
| 32 | Air dispersion system shall be provided for Equalisation Tank, Sludge holding Tank and Ariation Tanks. (UPVC/CPVC) :- 1 Lot (Air Grid) Make:- Prince/Suprim/Finolex/Prakash Surya/Eqv. |
| 33 | MBR Membrane with skid MOC - PVDF/SS-304 :- 1 Lot |
| 34 | Make- Deerfos/ Flosys/ Memtrix Technologies/ Willmer/ Eqv. |
| 35 | TUBE MEDIA :- Supply, installation, testing Tube Settler reactor Media Packeg a) TUBE MEDIA - 1 Lot |
| 36 | Make- MM Aqua/ PP Aqua/ Pharmtech/ Vasu Enviro/ Eqv. |
| 37 | SLUDGE TRANSFER PUMP / SLUDGE RECIRCULATION PUMP : 2 (1W + 1S) Nos. |
| 38 | Providing and fixing horizontal, centrifugal sludge transfer pump with 7-10mm solid handling. The pumps shall have CI casing, CI Impeller & CS shaft & sleeve with mechanical seal. MSEP common base frame. |
| 39 | Make-Assurity/Toshio/CNP |
| 40 | Capacity 55 m3/hr @ 8-10 m head |
| 41 | MEMBRANE SUCTION PUMP : 2 (1W + 1S) Nos. |
| 42 | Providing and fixing Horizontal centrifugal pumps for filtration. The pumps shall be made of CI casing, CI Impellar, CS shaft & sleeve, Mechanical Seal are connected to a TEFC induction motor. Motor to be suitable for 250/440 V, 3 Phase, 50 cycles AC power supply. |
| 43 | Make- Assurity/Toshio/CNP |
| 44 | Capacity 55 M3/Hr.@ 20-25M head |
| 45 | CIP Dosing Tank:- Supplying, installing, testing & commissioning of 1000 Litres capacity HDPE tank with inlet / outlet connection & piping. 2 No. |
| 46 | Make- SYNTAX / eqvt. |
| 47 | CIP DOSING PUMP:- |
| 48 | Capacity 55 m3/hr @ 25-30 M Head. |
| 49 | Make-Assurity/Toshio/CNP |
| 50 | CEB Dosing TANK :- Supplying, installing, testing & commissioning of 1000 Litres capacity HDPE tank with inlet / outlet connection & piping. :- 2 Nos. |
| 51 | Make- SYNTAX / eqvt. |
| 52 | CEB DOSING PUMP:- 2 Nos. |
| 53 | Capacity 0 TO 100 LPH |
| 54 | Make- Edose/ Aster/ Eqvt. |
| 55 | All Type Valves :- 1 Lot |
| 56 | Make- Astral/Supreme/Marck/Kartar/Eqv. |
| 57 | MS 'C' class : pumps & Blower interconnecting piping. :- 1 Lot |
| 58 | Make- Tata/Jindal/Surya Prakash/Eqvt. |
| 59 | Screw Press/Filter press:- Supply, erection & commissioning screw press / filter press with sludge feed as suitable :- 1 Nos |
| 60 | Make: Pharmtech / Vasu Enviro / Willmer / SkyLab/Akash/Eqv. |
| 61 | Pressure Gauge 0 to 7 KG (SS-304) :- 10 Nos |
| 62 | Make:- Hguru / Forbes Marshel / Eqvt. |
| 63 | Lavel Switch / Float Switch :- 6 Nos |
| 64 | Make:- Jigo / Sibaas / Inflo / Flo / Eqvt. |
| 65 | Membrene Back Wash Pump :- 2 (1W+ 1S) Nos |
| 66 | Capacity 110 m3/hr @ 20 M Head. |
| 67 | Make-Assurity/Toshio/CNP |
| 68 | Electro magnetic type flow meter :- Providing & fixing on line Electro magnetic type flow meter cum Totaliser for Monitoring the total flow, Flow rate. etc. Including electrical wiring from panel to flow meter. Complete with all type of Plumbing & Electrical connections, accessories, wiring, conduits & supports complete with all respect. :- 2 Nos |
| 69 | Make- Unitech/ UPC/ Eqv. |
| 70 | Flash Mixture With Tank :- 1 No |
| 71 | Make- Kirloskar/ Wilo/ Cromton Greves/ Eqv. |
| 72 | Belt Type Oil Skimmer :- 1 Nos |
| 73 | Make- Cutedge/Willmer/ Eqvt. |
| 74 | Ultra Voilet Lamp (UV lamp for 80% of Treated water Capacity) Make:- Alfa/Alpha/Eqv |
| 75 | Prefabricated MSEP UNIT/RCC/CIVIL/ZINK ALUMINIUM TANKS :- 1 SET (Make :- Eco Vobe Solutions Pvt Ltd/Willmer Eco Technologies) |
| 76 | Raw Sewage/ Equalization Tank -1 |
| 77 | Anoxic Tank-1 |
| 78 | Pre Clearfire -1 |
| 79 | Areation Tank-1 |
| 80 | Tube Settler Tank-1 |
| 81 | MBR Tank-1 |
| 82 | Treated Water Tank-1 |
| 83 | Sludge Holding Tank-1 |
| 84 | Sludge Drying Bed-1 |
| 85 | MCC PANEL for STP :- 1 Nos |
| 86 | Required MCC PANEL capacity of MCCB for DOL/ Star Delta starter and outgoing feeders for all pumps, motors and operating equipment. Each compartment shall contain Auto/ Manual switch, contactor, relay, single phase preventer, sequential controller for auto operation of working and standby equipment complete in all respects for the following, but not limited to: Make:- Willmer/Eqv. |
| 87 | Panel shall be designed on the actual HP as per model selection of pumps |
| 88 | starters shall be provided with Automatic level controller As Required |
| 89 | Notes: |
| 90 | All MCCBs / MCBs shall be of 18 / 10 KA breaking capacity and suitable for motor duty application. |
| 91 | All motor starters shall be provided with Automatic level controller |
| 92 | DOL starters shall be used for motors below 10 HP and Star-Delta Starters for other motors . |
| 93 | Provision for dry run protection shall be made in the panel. |
| 94 | MCC for STP as described above |
| 95 | All Control system to Make the STP fully automatic. The operation of the pumps shall be controlled by the level controller. |
| 96 | Supplying & Fixing of Cables , Conector, Cable Trays, to make Electrical Installation Complete. Necessary cable alleys, internal / cabling, wiring, cabling from MCC to various pumps / equipment and interlocking. |
| 97 | Total PART A : Supply, Installation, testing & commissioning of 1100 KLD capacity CETP (1.1 MLD) Compact type MBR technology based CETP as per above specification |
| 98 | Part B |
| 99 | LIFTING WELL WASTE WATER TRANSFER PUMPS / RAW SEWAGE PUMP : 3 (1W + 2S) Nos. |
| 100 | Providing & fixing fully submersible sewage handling type pump for raw sewage transfer from Sewage Lifting Well to STP. The pump shall have complete CI construction, TEFC induction motor including pressure gauge, lifting arrangement for the pump. Solid handling shall be 25-40 mm(With Cutter) with Electrical Penal and Automatic Lifting Arrengment, Lifting Well will be constructed RCC with Bar screen and Minimum Capacity is 110 KLD. Make- Assurity/Toshio/CNP |
| 101 | Capacity : 55 M3/hr @ Discharge Head 60-70 M head (1 Working + 2 Standby), |
| 102 | OPERATION & MAINTENANCE FOR 05 YEAR STP |
| 103 | The SITC of CETP (Sewage Treatment Plant + Effluent Treatment Plant) includes 05 years of Defect liability peroid). All Parts and Machinery maintenance, Replacement included in 05 Year DLP. The Operation and maintanance of above CETP (STP+ETP) will be for 05 years which includes 24x7 operation of CETP each by skilled operator, regular backwashing/cleaning, all Consumables and any other activity required for un-hindered operation of CETP. The Payment of O&M cost will be done on Monthly basis (after every 1 months) after getting report of outlet parameters matching with prevailing RPCB/CPCB norms. |
| 104 | Five Year O & M With Plant DLP |
| 105 | OPERATION & MAINTENANCE COST FOR 1st YEAR |
| 106 | OPERATION & MAINTENANCE COST FOR 2nd YEAR |
| 107 | OPERATION & MAINTENANCE COST FOR 3rd YEAR |
| 108 | OPERATION & MAINTENANCE COST FOR 4th YEAR |
| 109 | OPERATION & MAINTENANCE COST FOR 5th YEAR |
| 110 | Sewage Lifting Piping (RUPDP SOR2023) |
| 111 | Providing, lowering, laying in trenches, aligning, fixing in position and double flanged (welded) centrifugally (spun) Ductile iron ISI marked K-9 grade pipes as per IS:8329-2000 (amended upto date), (including jointing and jointing material) complete including all material, labour, hydraulic testing and commissioning as per Technical Specifications and as per direction of Engineer. Note : E/w to be measured and paid separately. |
| 112 | 150mm |
| 113 | Providing, lowering, laying, aligning, fixing in position at and jointing at all level/ depths DI K-12 standard specials with rubber ring (EPDM/SBR) joints as per IS: 5382-1985 such as tees, bends, tapers, caps etc. within trenches in DI pipe line complete including all material, labour, testing and commissioning along with pipe line as per Technical Specifications and as per direction of Engineer. Note : E/w to be measured and paid separately. |
| 114 | Specials flanged DI K-12 |
| 115 | Upto 300mm |
| 116 | Earth work in excavation in open area, STP, WTP, Pumping station with mechanical means including dressing of sides and ramming of bottoms, including getting out the excavated material, disposal of excavated material lead upto 1000m at suitable site as per as per drawing and as per direction of Engineer. (Measurements for payment to be done as per standard drawings). in all kinds of soil Upto 3.0 m depth |
| 117 | Providing, laying and compacting plain/ reinforced cement concrete of specified grade in foundation/ levelling course/ pile cap using concrete mixer and vibrator complete including cost of form work, as per drawing and technical specifications and as per clause 1100, 1500,1700,2100 of MoRT&H specification including all scaffolding material, labour, machinery. |
| 118 | RCC Grade M -35 |
| 119 | Reinforcement for R.C.C. work at all levels including straightening, cutting, bending, placing in position and binding all complete. |
| 120 | Thermo-Mechanically Treated bars. |
| 121 | Providing and fixing Barricading at site of work for restricting the general public using 40 mm dia M.S. pipe (\\"B\\" class) as vertical post with average spacing of 1.80 meter between two vertical posts, having height at least 1.5 m above road/ ground level and at least 30-45 cm below road/ ground level by making suitable size hole in road/ ground, providing and fixing suitably two rows of 100mm wide PVC Tape preferably of red colour. The M.S. pipe shall be painted in red and white colour strips as per approved pattern as and when it becomes shabby but at least after every alternate shifting at new location. After shifting/ removal of barricading the hole shall be filled up properly and site is to be cleared in all respect. (Note: measurement is to be done in linear basis) |
| 122 | Centering and Shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation , footings, strap beam, raft , bases of columns etc. |
| 123 | Providing, lowering, laying, aligning, fixing in position and jointing at all level/ depths full round HDPE DWC (double wall corrugated) pipes of SN8 grade as per IS 16098 (Part 2) amended upto date in trenches in complete including all material, labour, sectional hydro testing (including the cost and conveyance of water to site for testing) and commissioning as per Technical Specifications, drawings and as per direction of Engineer. Note : E/w to be measured and paid separately. Length of pipe shall be measured in between the outer wall of two manholes / Inspection chambers. Pipe in the manhole/inspection chamber’s wall shall deemed to be included in the item of manhole/inspection chamber shall not be payable. |
| 124 | 200 mm ID |
| 125 | 250 mm ID |
| 126 | 300 mm ID |
| 127 | Providing granular bedding having width = outer dia of pipe (Bc) + 500mm, thickness below pipe = 0.25Bc or 100mm (whichever is higher) and haunching = 0.5Bc, with graded hard crusher broken stone of 100% passing through 20mm sieve, 20 to 50 % passing through 10mm sieve and 100 % retain on 6.3mm sieve, laying in layers of thickness 10/15cm including ramming, consolidation etc complete for all type of pipes of following sizes as per drawing and or as directed by Engineer. |
| 128 | 200 mm ID |
| 129 | 250 mm ID |
| 130 | 300 mm ID Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 01, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 08, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysJul 09, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender