Tender For special Repair To Bldg No T- 46 & T-53 (Store) Of 11 Madras And Provn Of 02 X Interlocking Plinth (27 X 10M Each) Infront Of 66 Ad Bty & 68 Ad Bty Radar Shed Of 46 Ad Regt And Provn Of Pre Fab Wall For 273 Coy Asc And Provn Of Shed Near Su
Tender Value
28.92 Lakhs
Estimated cost
Bid Submission
22 Jul 2026
13 days left
EMD
57840
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kachchh → Gujarat
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Bldg No T- 46 & T-53 (Store) Of 11 Madras And Provn Of 02 X Interlocking Plinth (27 X 10M Each) Infront Of 66 Ad Bty & 68 Ad Bty Radar Shed Of 46 Ad Regt And Provn Of Pre Fab Wall For 273 Coy Asc And Provn Of Shed Near Suvidha Complex At Mil Stn Bhuj Under Ge (A) Bhuj.
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete of any description and in any position (reinforced) in ground floors/ paving not exceeding 15 cm thick (below or above GL) complete all as specified and directed. |
| 2 | M&L for machine cut kota stone slab flooring 18-20 mm (+ 2mm) thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing over and including 15mm thick screed bed or bedding layer in CM 1:4 complete all as specified and as directed. |
| 3 | M&L for mirror polished machine cut Kota stone slab 15-16 mm thick in riser of steps, skirting, dado and pillar laid over and including 10mm thick rendering in CM 1:4 and jointed complete all as specified and as directed. |
| 4 | M&L for machine cut Kota stone slab 20 mm to 25 mm thick, as in slab/plateform /Shelves and thread for steps set and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing to give granite finish, complete all as specified and directed. |
| 5 | Demolition of precast concrete block walling and similar items i.e.. ashlar facing dressed stone work, precast concrete articles etc., of any description and in any position, built in cement mortar, including all quoins, arches and pillars etc. complete all as specified and directed. |
| 6 | M&L for precast cement concrete block masonry with solid blocks of PCC (1:3:6) type C-1 (using 20mm and 12.5 mm graded stone aggregate in the proportion as directed) exc 10cm in width and set and jointed in Cement Mortar (1:6) complete all as specified and directed. |
| 7 | Taking down cement plaster of any description and in any position of brick/concrete surfaces on walls/celling etc. including racking out joints, hacking for key, scrubbing down with water etc & prepared to receive new plaster complete all as specified and directed. |
| 8 | M&L for 15 mm thick rendering on block/brick masonary wall surfaces in CM 1:4 finished fair and even complete all as specified and directed. |
| 9 | M&L for rendering 10 mm thick in CM (1:6) on fair faces of brick/block work or concrete surfaces/stone masonry and finishing the surfaces even and smooth without using extra cement complete all as specified and directed. |
| 10 | M & L for preparation of old/new surfaces of wall and applying two coat of distemper oil emulsion over a coat of alkali resistant primer complete all as specified and directed. |
| 11 | Material & Labour for preparation of old/new wall surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed. |
| 12 | Demolition of cement concrete of any description and in any position (unreinforced) in ground floors/ paving not exceeding 15 cm thick (below or above GL) complete all as specified and directed. |
| 13 | M&L for PCC (1:3:6) type C2, (using 40mm graded stone aggregate) as in plinth protection, 75 mm thick, finishing the surface even and smooth w/o using extra cement complete all as specified and directed. |
| 14 | Taking down chowkat or frames n.exc 1.5 sqm with shutters without taking off shutters from the frame and removing to store complete all as specified and directed. |
| 15 | Taking down chowkat or frames exc 1.5 sqm & n exc 4 sqm with shutters without taking off shutters from the frame and removing to store complete all as specified and directed. |
| 16 | S & F Powder coated Aluminium alloy sections sliding windows with frames Series-C (20mm) and , 3 track sliding shutters duly fitted with neoprene beading, glazing clips, shutters with tinted glass 5mm thick and stainless steel wire cloth 0.36mm dia and average width of aperture 1.4mm , aluminium alloy handles etc. complete all as specified and directed. |
| 17 | S&F 30 mm thick factory made Flush shutters , solid core construction , with block board core and plywood face panels both face is covered with decorative face veneer with lipping/frame to match face on both sides with lipping/frame to match complete all as specified and directed. |
| 18 | M&L preparation of the new wooden surfaces exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 19 | S&F aluminium handles cast type, anodized of 150 mm size complete all as specified and directed. |
| 20 | S&F 150 mm long aluminium anodised , barrel tower bolt of extruded section and fixed all as specified and directed. |
| 21 | S&F butt hinges 100mm long medium weight, cold rolled mild steel complete all as specified and directed. |
| 22 | S&F Aluminium alloy, anodised, sliding door bolt 250mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. |
| 23 | S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed Fe 410-W (Gde- E- 250) quality- A complete all as specified & directed. |
| 24 | Dismantling of stone slabs and tiles (Kota stone etc.) of any description or any thickness in floors, aprons, skirting, dado etc. laid bedded and pointed in any mortar complete all as specified and directed. |
| 25 | M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) in cooking platform, Jambs cill and like set in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match shade of granite including rounding of exposed edges of slab smoothly and polished complete all as specified and directed. |
| 26 | M&L 75 mm thick PCC 1:3:6 type D-2 (using 40mm graded stone aggregate) as in as in sub base complete all as specified and directed. |
| 27 | Providing precast cement concrete Type B1 1:2:4 (20 mm graded aggregate) in appex stone/kerb stone with plain fair faces including chamfers, weathering throting etc and set in cement mortar 1:4 complete with joints to math size and shape as approved GE |
| 28 | Dismantling wrought iron or mild steel work of any description and in any position not otherwise specifically provided for (framed/ unframed work) complete all as specified and directed. |
| 29 | S&F Roof trusses (Framed), trussed, purlins, crane gantries, rails and fastenings and heavy brackets framing (Beam, tee, angle, channel, flat or MS hollow square/ rectangular any type, size/ sections), including distance pieces, cleats etc conforming to FE- 290 (Gde-E- 165), including fabrication, erraction and fixing complete all as specified and directed. |
| 30 | Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed. |
| 31 | S&F Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall fixed with self tapping screws etc; complete all as specified and as directed. |
| 32 | S&F Pre-painted galvatume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall fixed with self tapping screws etc; complete all as specified and as directed. |
| 33 | Preparing new/old or previously untreated surfaces of steel or iron work of any description and girth over 10cm and applying two coats of synthetic enamel paint complete all as specified and as directed. |
| 34 | Surface Excavtion n exc 30 cm deep and average 15 cm deep and getting out soft/loose soil complete all as specified and directed |
| 35 | Removing excavated material at a level n.exc 1.5 m above the starting point 50 mtr depositing where complete all as specified and directed. |
| 36 | M&L for hardcore of broken stone of gauge n. exc 63mm, deposited spread and levelled in layers n exc 15 cm thick watered, rammed and rolled to true surface with 8 to 10 tonne power roller/vibratory roller complete all as specified and directed. |
| 37 | M & L 100 mm thick plain cement concrete type D 2 1;4:8 (Using 40 mm grade stone aggregate ) as in sub base complete all as specified and as directed. |
| 38 | S&F providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line,level and curvature,jointed with cement mortar 1:3,including making joints with or without grooves(thickness of joints except at sharp curve shall not to more than 5 mm),including making drainage opening wherever required complete all as specified and as directed. |
| 39 | M&Lfor preparation of new or previously untreated surfaces of concrete over 10 cm girth or width and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and as directed. |
| 40 | Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 25mm thick compacted bed of fine sand, compacting and proper embedding/laying if inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified & directed. |
| 41 | Dismantaling and taking down copper / aluminium point wiring any type / size complete with removing all connection and accessories such as switches , sockets, ceiling rose,pendent holder,fan regulator any type , all type of fitting , batten , steel or PVC conduit , casing caping etc compele and making good the disturbed surface complete all as specified and directed. |
| 42 | Taking down old and unsrevicable sheet metal enclosure , switch fuse unit , distribution bord any type /way / capacity including fuses,MCB's , insulator etc complete after removing all connection and making good the disturbed surface all as directed. |
| 43 | M&L for Point wiring complete with FR PVC insulated unsheathed , 1100 V grade conforming to IS 694 , 1.5 Sqmm (Norminal area) multistranded ,copper conductor cable drawn through in non metallic rigid PVC conceled/surface conduit medium grade ,minimum 20 mm dia, ISI Marked, with sutaible size of 1 to 8 module metal flush boxes and back plate for mounting of modular switches/socket and regulators and including modular fornt plate with all acessories complete all as specified and directed. |
| 44 | (a) One light point controlled by one way one switch SP 5 Amps ,240 V complete all as specified and directed. |
| 45 | (b) One ceiling/exhaust fan point controlled by one way one switch SP 5 Amps, 240 V complete all as specified and directed. |
| 46 | (c) One switch socket outlet 3 Pin, 5 Amps, SP on independent board complete all as specified and directed. |
| 47 | (d) One switch socket outlet 3 Pin, 5 Amps, SP on same board complete all as specified and directed. |
| 48 | All as per the above item No 43 herein before but with 2.5 Sqmm cable for 3 Pin 5/15 Amps switch socket outlet complete all as specified and directed. |
| 49 | S&F modular switch one way 6 Amps , 1 module type complete all as specified and directed. |
| 50 | S& f modular socket , 6 Amps , 2/3 pin combined 2 module complete all as specified and directed. |
| 51 | S& f modular switch socket combination, 6 Amps / 16 Amps , 2/3 pin combined 2 module complete all as specified and directed. |
| 52 | S&F ceiling rose surface backlite 65 x 20mm size three terminal ISI marked complete all as specified and directed. |
| 53 | Supply and fixing LED lights fitting 1x 20 W, 220V,AC decorative box type with driver, holder including LED tube light connecting upto PVC insulated 3 core flexible cable from ceiling rose to fitting drawn through in PVC flexible conduit including as per site requirement and 2 Nos of round or square PVC bolck for fixing of FTL fitting complete all as per directed. |
| 54 | supply & fixing modular fan regulator step type , 1 module complete all as specified and directed. |
| 55 | S&F sheet metal enclosures for distribution board when MCB to be used SPN ( Single pole and neutral ) 8 way, 240 Volts, sheet metal powder coated, IP 42 protection with 200 Amps rated bus bar, double door type complete all as specified and directed. |
| 56 | S&F MCB SPN,40 Amps, 240 Volts, rupturing capacity 10 KA.\\"C\\" Series complete all as specified and directed. |
| 57 | S&F MCB SP, 5 to 32 Amps, 240 Volts, rupturing capacity 10 KA \\"C\\" Series complete all as specified and directed. |
| 58 | M&L , earthing complete for machinary / Equipment installed at power house / sub station with galavanised steel earth plate electrode of size 60 cmx 60 cmx 6 mm thick buried directly in ground ( earth pit not less then 2.25 m deep below the normal ground level ) with top edge of the earth plate not less then 1.5m below normal Ground level connected galvanised earth lead wire 4.0mm dia by means of bolts, nuts, washerws and check nuts all shown in electrical plate No.3 of SSR Part- I connected to main board / disribution board complete .Earthing GI lead and GI protection pipe 15 mm dia light grade upto 7.5 m from earth pit connecting to machinary/ equipment, testing point, all as specified and testing on completion all as per directed. |
| 59 | Note :- (i) The unit rate shall also included for earth work in hard /dense soil , PCC type C-I (1:3:6) chamber , PCC 1:2:4 type B-I cover 50 mm thick reinforced with 8 mm dia TMT bars,150 mm c/c both ways, funnel with watering pipe 20 mm dia medium graded , GI protection pipe light grade 15 mm dia and wire mesh complete in addition to items No. 1(a) to (e) of preamble (notes) under sub heading earthing specified on SI page No. 389 of SSR Part - II.(ii) Earthing lead and GI protection pipe beyond 7.5 mtrs will be measured and paid separatelly if required under appropriate Schedule.Note (i) Earthing shall be tested as specified in casul 19.137 of SSP PART - I 2009 , to the entire satisfication of Engr-in-Charge. (iii) On teting after complataion of earthing , if the desired earth resistance is not obatined the earthing wiil be re done by the contractor at his on risk and cost to the entire satisfaction of the Engr - in - charge. |
| 60 | Supply and fix in replacement XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100 volts grade of cross sectional area 25 sqmm 2 core complete all as specified and directed |
| 61 | Excavation in trenches in soft/loose soil , not.exc 1.5 mtr wide and not.exc 1.5 mtr deep and getting out in soft/loose soil for laying of cable/foundation of pole and stay etc in complete all as specified and directed. |
| 62 | Returning filling including spreading, levelling, watering and well ramming in layers n.exc 25 cm complete all as specified and directed. |
| 63 | M&L for sand cushioning in trenches for protection of LT under ground cable including watering and consolidation complete all as specified and directed. |
| 64 | Supplying and laying un-reinforced precast concrete cable cover class LV Type 1, flat, size 250mm x 150mm x 40mm complete. Complete all as specified and directed. |
| 65 | Supply and laying GI tube light grade 50 mm bore complete. Complete all as specified and directed. |
| 66 | Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete,complete all as specified and directed. |
| 67 | Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm as in any type of soil complete all as specified and directed. |
| 68 | M/L for providing PCC 1:2:4 type B2 using (40mm graded stone aggregate) in foundation filling and mass concrete complete all as specified and directed. |
| 69 | M & L Pre Stressed pre cast RCC (M-25 Grade) colum of size 150mm x 150 mm and 2.44 Meter Height with contineous vertical groove of size 60mm x 35 mm at two sides of column to receive the precast panels, Inclucing reinforced with 7 Nos wires of 3 mm dia high tensile corbonized steel, surfaces finsihed even and smooth including in postion complete all as specified and directed. |
| 70 | M & L Pre Stressed pre cast RCC (M-25 Grade) Panels of 1800 mm x 300 mm size and 45 mm thick, reinforced with 4 nos wires of 3mm dia high tensile carbonized steel, including fixing in position in between column grooves and jointing and flush pointing of all horizontal and vertical joints of pannels with cement mortar 1:3 complete al as specfied and as directed. |
| 71 | M & L for New surface of walls and applying two coat of acrylic weather proof paint (Exterior grade) over a coat of primer complete all as specified and directed. |
| 72 | M&L 4mm dia galvanised steel wire, 150x100mm mesh, made up into mattresses or cages, lapped, wired and laid in position, including closing after filling complete all as specified and directed. |
| 73 | S&F roof trusess (framed), vertical pole , trussed ,purline, crane gantries rails and fastenings and heavy bracket framing (beam tea angle chanell or flat section ) including distance pieces,cleats etc confirming to Fe 410-W (grade -E-250) quality A complete all as specified and directed. |
| 74 | M&L for framed brackets of angles or tees with web and franges cut to shape, drilled and countersunk for screw incl bending and welding angles, as necessary gusset plate plates, reviting etc 10 kg each brackets confirming to Fe 290 Gde E-165. |
| 75 | NOTE APPLICABLE FOR ALL ITEMS :- If rate quoted for similar/identical items in same part of Sch ‘A’ is at variance, the lowest rate quoted shall only be considered for payment to the contractor. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 01, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 22, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 13 daysJul 24, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 15 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender