Tender For Internal Finishing And Miscellaneous Civil/Sanitary Repair Work In Staff Quarter No. C-09 At Ajmal Bagh, Jamia Millia Islamia.
Tender Value
99401
Estimated cost
Bid Submission
21 Jul 2026
15 days left
EMD
1988
Bank guarantee accepted
Document Fee
150
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Delhi → Delhi
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Internal Finishing And Miscellaneous Civil/Sanitary Repair Work In Staff Quarter No. C-09 At Ajmal Bagh, Jamia Millia Islamia.
BOQ
| Sl. No. | Item Description |
| 1 | CEMENT CONCRETE (CAST IN SITU) |
| 2 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :_1:2:4 (1 cement : 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 3 | CLADDING WORK |
| 4 | Providing and fixing expansion hold fasteners on C.C. /R.C.C./Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete._Wedge expansion type_Fastener with threaded dia 10 mm |
| 5 | Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3(1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 6 | WOOD AND P. V. C. WORK |
| 7 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters._30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 8 | Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete._With 12 mm mild steel U beading |
| 9 | STEEL WORK |
| 10 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.-Hot finished welded type tubes |
| 11 | FLOORING |
| 12 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 13 | ROOFING |
| 14 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes._110 mm diameter |
| 15 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS :5382, leaving 10 mm gap for thermal expansion._Bend 87.5°_110 mm bend |
| 16 | Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'S or 'L' hooks, bolts & nuts 8 mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafers, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified._2 mm thick flat |
| 17 | FINISHING |
| 18 | 12 mm cement plaster of mix:_1:6(1 cement: 6 fine sand) |
| 19 | 15 mm cement plaster on rough side of single or half brick wall of mix:_1:6(1 cement: 6 coarse sand) |
| 20 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 21 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC (Volatile Organic Compound ) content less than 50 gram/ litre, of approved brand and manufacturer including applying additional coats wherever required to achieve even shade and colour_Old work (one or more coats) |
| 22 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:_One or more coats on old work |
| 23 | REPAIRS TO BUILDING |
| 24 | Dismantling W.C. Pan of all sizes including disposal of dismantled materials including malba all complete as per directions of Engineer-in-Charge. |
| 25 | Dismantling and Demolishing |
| 26 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge._Nominal concrete 1:3:6 or richer mix (including equivalent design mix) |
| 27 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 28 | SANITARY INSTALLATIONS |
| 29 | KiProviding and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :_tchen sink without drain board_610x510 mm bowl depth 200 mm |
| 30 | Providing and fixing white vitreous china water closet squatting pan (Indian type) :_Long pattern W.C. pan of size 580 mm |
| 31 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete._Flexible pipe_32 mm dia |
| 32 | WATER SUPPLY |
| 33 | Providing and fixing PTMT bib cock of approved quality and colour._15 mm nominal bore, 122 mm long, weighing not less than 99 gms |
| 34 | Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball._20 mm nominal bore, 120 mm long, weighing not less than 198 gms |
| 35 | Modified Estimated Cost after using correction factor on DSR 2023 on account of GST @ 0.973 * 102159 = 99401 Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jun 30, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 21, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 15 daysJul 23, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 17 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender