Tender For Repair/ Maintenance And Rewinding Of Burnt, Centrifugal Pump Sets And Monoblock Pump Sets And Alied Works At Zone ‘A And Day To Day Maintenance Of Swimming Pool And Other Alied Works At Gms Under Ge (I) Gos
Tender Value
Ref. Documents
Estimated cost
Bid Submission
23 Jul 2026
15 days left
EMD
90000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ganjam → Odisha
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair/ Maintenance And Rewinding Of Burnt, Centrifugal Pump Sets And Monoblock Pump Sets And Alied Works At Zone ‘A And Day To Day Maintenance Of Swimming Pool And Other Alied Works At Gms Under Ge (I) Gos
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling complete Centrifugal /Mono Block motor of any type and overhauling the pump re-threading of wornout holes of studs and providing over size studs with nuts & washers. Rematlling and balancing of shaft, replacement of gunmetal bush bearing and gland packing of pump set. and refitting the same after the repair/replacement duly all as specified and tested for smooth functioning of capacity 40 HP complete. |
| 2 | All as per item No 1 above but capacity 30 HP |
| 3 | All as per item No 1 above but capacity 20 to 25 HP |
| 4 | All as per item No 1 above but capacity 10 to15 HP |
| 5 | All as per item No 1 above but capacity 5 to 7.5 HP |
| 6 | All as per item No 1 above but capacity 1 to 3 HP |
| 7 | Dismantling the power supply of electric motor any type including dismantling from pump and taking to workshop with necessary transportation and opening the complete motor and rewinding the rotor with super enameled copper wire as per the existing gauge with necessary insulation, sticks and varnishing, including replacement of shaft bearing 02 Nos and motor terminals plate/cable ducts complete of capacity 40 HP including painting complete all as directed. |
| 8 | All as per item No 7 above but of capacity 30 HP electric motor any type. |
| 9 | All as per item No 7 above but of capacity 20 to 25 HP electric motor any type. |
| 10 | All as per item No 7 above but of capacity 10 to 15 HP electric motor any type. |
| 11 | All as per item No 7 above but 5 to 7.5 HP electric motor any type. |
| 12 | All as per item No 7 above but 1 to 3 HP electric motor any type. |
| 13 | Note for item No :7 to 12- Pump/Motor shall be dismantled and winding shall be tested continuity at site if winding fail/burnt is established than winding shall be cut at site before issuing gate pass. The coated rate deemed to included . |
| 14 | Replacement of old rusted GI Column Pipe heavy grade of size 50 mm dia in pieces of 3.3 metre long each, lathe m/c threaded both ends in the bore/open wells complete all as specified and directed. |
| 15 | Replacement of old rusted heavy grade GI socket of size 50 mm dia complete all as specified and directed by EIC. |
| 16 | Replacement of impeller upto 7.5 HP submersible pump set |
| 17 | S&F in repair PVC insulated submerssible cable water proof flate type 3 core with standed copper conductor cable, 4 Sqmm, 1100 volts grade including cable lugs/joints, connection to submerssible motor and other end to aluminium armoured cable including jointing complete as directed |
| 18 | S&F in repair HDPE Borecaps of size 200/250mm dia complete all as directed by Engineer-in-Charge |
| 19 | S&F in repair of steel rope in submersible bore wells from motor to top edge of the bore well of size 6 mm dia(multi wire steenless steel) for holding of submersible pump motor set all as directed by Engineer-in-Charge. |
| 20 | Supply and replacement contactor 16 Amps capacity 2 NO + 2 NC, AC 3 phase 415 Volts, 50 HZ |
| 21 | All as per item No 20 above but 25 Amps capacity. |
| 22 | All as per item No 20 above but 32/35 Amps capacity. |
| 23 | S&F in repair Star Detla Timer 0-30 Seconds duration |
| 24 | Supply and fix in replacement of MCB TP 40 amps, |
| 25 | Supply and fix in replacement of electronic adjustable Cyclic timer 0-30 Seconds duration sutable to existing submersible motor panel board complete all as specified and as directed |
| 26 | Supply and fix in replacement of dry Run Guard and overload protection with phase failure relay sutable to existing submersible motor panel board complete all as specified and as directed |
| 27 | Supply and fix in replacement of pressure switch sutable to existing pressure motor complete all as specified and as directed |
| 28 | Supply and fix in replacement of Phase Monitoring Divice 440 volt 3 phase sutable to existing submersible motor panel board complete all as specified and as directed |
| 29 | Supply and fix in replacement of Voltage Monitoring Divice 440 volt 3 phase sutable to existing submersible motor panel board complete all as specified and as directed |
| 30 | S&F in repair DOL Starter for submersible pump set type MN -16 and relay range 7 HP,10 HP Amps with contactor complete all as specified and as directed. |
| 31 | Supply and fix in replacement of Push Button sutable to existing submersible motor panel board complete all as specified and as directed |
| 32 | Supply and fix in replacement of Volt meter sutable to existing submersible motor panel board complete all as specified and as directed |
| 33 | Supply and fix in replacement of Ammeter sutable to existing submersible motor panel board complete all as specified and as directed |
| 34 | Supply and fix in replacement of Coupling Spider L-290 Heavy Duty complete all as specified and directed. |
| 35 | Supply and fix in replacement gun metal NRV of size 50 mm dia. |
| 36 | Supply and fix in replacement over load relay 6 to 10 Amps for submersible motor panel board complete all as specified and as directed |
| 37 | Supply and fix in replacement over load relay 9 to 15 Amps for submersible motor panel board complete all as specified and as directed |
| 38 | Supply and fix in replacement over load relay 14 to 23 Amps for submersible motor panel board complete all as specified and as directed |
| 39 | Supply and fix in replacement over load relay 25 to 40 Amps for submersible and motor panel board complete all as specified and as directed |
| 40 | Carrying out Chemical analysis test of water collected from following bore wells and sump through Govt approved lab complete all as specified and directed 1.Main pump House 2. IB pump House. 3. Map officer pump house 4. Kajupahari Pump House 5. TTW Pump House 6. Map JCO Pump House 7. MH Pump House 8. Army School Pump House 9. Adm Regt Pump House 10. Static Work Shop Pump house 11. Record Pump house. 12 AD Centre Pump House 13. Amn Dump Pump House.14.Rushikulia pump house |
| 41 | Supply and Fix soft starter 3 phace 415 volts suitable for 15 to 40 HP pump set including taking down old unserviceable contactor and relay, coil etc,and supply and fix same complete all as specified and as directed |
| 42 | Disconnecting the electric connection and taking out the submersible pump set from bore / open well of any capacity including GI column pipe complete and lowering down repaired motor with column pipe, welding joints and connecting electrical connection as directed and transportation of submersible pump set upto 7.5 HP 3 phase from pump house to any location in GMS area to contractors work shop repaired pump set for relowering, dismantling and carrying out necessary repairs complete aii as specified and directed |
| 43 | Dismantling of submersible motor 7.5 HP 3 phase from pump house at any location in GMS area under AGE E/M GOS Yard, transporting to contractors workshop, dismantling and carrying out necessary repairs/replacement of motor as per the following :- (a) Cutting out existing winding of stator of submersible motor of any make and rewinding with same size of copper winding wire as existing as directed by the EIC. (b) Straightening the slot of starter of submersible motor of any make (c) Replacement of thrust washer and bearing complete of submersible motor of any make. (d) Replacement of worn-out bushes of submersible motor as per manufacturers design and specification. (e) Replacement of sand guard (f) Providing of sleeves in end plate of submersible motor (g) Replacement of cable gormmet (h) Replacement of water seal (i) Replacement of studs with nuts (j) Lathe work of motor shaft, turning to bring it to original size and shape and plastering of shaft of submersible motor for smooth functioning on described amps |
| 44 | All as per item No 43 above but of capacity 5 HP |
| 45 | All as per item No 43 above but of capacity 3 HP |
| 46 | Note for item No 43 to 45 :- Pump/Motor shall be dismantled and winding shall be tested continuity at site if winding fail/burnt is established than winding shall be cut at site before issuing gate pass. The coated rate deemed to included . |
| 47 | Dismantling of submersible pump 7.5 HP capacity from pump house at any location in GMS area under AGE E/M GOS Yard, transporting to contractors workshop, dismantling and carrying out necessary repairs/replacement of pumps/Testing as per the following:-(a) Replacement of coupling complete (b) Overhauling of submersible pump and carrying out the following repairs. (c) Lathe work including balancing of pump shaft and cutting of key slots (d) Re-threading of worn-out studs holes and providing over size studs with nuts (e) Replacement of bowel bushes (f) Replacement of neck ring (g) Replacement of steel distance pieces (h) Replacement of bowel (j) Replacement of head extension |
| 48 | All as per item No 47 above but of capacity 5 HP |
| 49 | All as per item No 47 above but of capacity 3 HP |
| 50 | Supply and Fix gland rope in GMS pump house of existing motor any capacity ,and sluce valve any capacity all as specified and as directed. |
| 51 | Supply and Fix stainless Steel nut and bolt 10 mm to 16 mm ,40 mm long complete all as specified and as directed |
| 52 | Supply only copper lugs 10 to 35 sqmm for existing panel board complete all as specified and as directed |
| 53 | Supply and Fix sensor switch suitable to existing pressure motor any capacity ,all as specified and as directed. |
| 54 | Flushing the bore well for flushing of silt, fine sand etc by air compressor of suitable capacity and pumping out turbidity till obtaining clear water all as directed and as per site requirement. |
| 55 | Excavation in trenches n .exc 1.5 mtr wide and not exec 1.5 mtr depth and getting out in looses/soft soil complete all as specified and directed. |
| 56 | Returing filling in incl spreading leveling, watering and well ramming in layer not less than 25 cum each layer complete all as specified and directed. |
| 57 | Removing excavated material to a distance not exc 50M and depositing where directed at a level n.exc 1.5 mtr above the starting point complete all as specified and directed. |
| 58 | Supply and fix double wall corrugated HDPE pipe 50mm outer dia for protection of UG cable complete all as specified and directed |
| 59 | Material and labour for filling the road / hard standings cut for laying cable with PCC 1:2:4, type B2, using 40 mm graded stone aggregate and finishing the surface even and smooth without using extra cement all as specified and directed. |
| 60 | M & L GI tubing light grade 40mm borewith all fitting(ISI marked) for protection of cable fixed to pole/wall / laid under floor or road including necessary joints and clamps complete all as specified and directedd |
| 61 | Boring of holes horizontally for laying of 40mm dia pipe (minimum depth 0.60 Mtr from top level) under road, Pavement, hard standing complete all as specified and directed. |
| 62 | Supply and fix in replacement of MCCB 4 pole , 415 V , fixed type 63 Amp panel mounting type ,with breaking capacity 16 KA AC |
| 63 | Supply and fixing street light fitting LED type 25 Watt new generation in aluminium PDC housing, toughened glasscover with IP 66 protection complete in all respect with GI tubing 25mm/40mm dia, mounting bracket with its clamp incl two coats of synthetic enamel paint over a coat red oxide primer and with all accessories, incl connecting of with 2 run of flexible aluminium/copper conductor of size 1.5 sq mm cable from fitting to junction box/conductor to street light as suitable on site, testing & commissioning complete all as specified and directed. |
| 64 | Supply and fixing LED flood light 200 watt Lumos II new generation LED with high luminous efficacy of 120 lm/w protected to IP-66 with front toughened glass complte in all respect with GI tubing reqd in site, mounting bracket with its clamp incl two coats of synthetic enamel paint over a coat red oxide primer and with all accessories, incl connecting of with 2 run of suitable flexible aluminium/copper conductor of size 2.5 sq mm or fixed in appropriate size of PCC block made with PCC 1:3:6 with fixing arrangement suitable on site, testing & commissioning complete incl taking down old unsv any type and make all as specified and directed. |
| 65 | Taking out old UNSV and Supply, laying, jointing and testing of XLPE insulated, armoured, heavy duty LT under ground cable 1100 Volts grade with aluminium conductor laid in trenches, on poles, through pipes, fixed to walls etc cross sectional area for 10 Sqmm 4 Core, including taking down old, complete all as specified and directed. |
| 66 | All as per item No 65 above, but 16 Sqmm 4 Core. |
| 67 | Material and labour for swimming pool of size of 50 mtr x 21 mtr, water of capacity 3200000 ltrs, combined diving and swimming pool basic depth varies from 4ft, 6ft, 8ft and to meet to the desired level of cleanliness by adding the chemicals such as PH solution and non ferrous alum as coagulant / settling aids, soda ash, Dry acid, Sodium Bi-Alginex,chlorotex regent,TCA90 chemical thourgh the respective dozin system with adequate quantity and Daily Cleaning of swimming pool by operating vaccum pool suction sweeper , daily cleaning of bottom incl deep, slop surface by under water cleaner and removing sediment particle from bottom by using suction sweeper so as to maintain deepest point of pool must be visible at all times without distrubing the swimming pool schedule of operation, quality of water to be checked as directed by Engr-In- Charge frequently, complete all as directed. Note : T&P such as necessary equpments for under water cleaner, brushes, breathing arrangements shall be provided by the contractor Chemicals not covered under Sch shall be deemed to be included in the unit rate quoted. Following water standard parameters to be maintained on pool round the clock.PH - 7.4 to 7.6 Free chlorine -0.5 to 1.0PPM Total alkatinity -75 PPM Minimum ,TDS-500PPm Minimum,Total Hardness -200PPM MinimumNote :(i) Any damage to the Department assets handed over for cleaning and maintenance of swimming pool with negligence of firm shall be made good by the firm without any extra cost to the department. (ii) T & P, material, labour, element involved in cleaning shall be provided by firm without any extra cost to the Deptt. |
| 68 | M & L for carry out water quality anyalsis for bacterial , chemical and biological analysis including for collection of water samples from the swimming pool all as specified by Engineer-in-charge and testing from Govt approved testing laboratory , submitting of report from minimum following parameters . (a) pH (b) Total alkatinity (c)Total Hardness(d) Magnesium as Mg 9mg/I) (h) Remarks of Govt testing lab . |
| 69 | M&L for pumping out existing water from swimming pool, balancing chamber, under ground water storage sump complete, Cleaning the pool, chamber and under ground water storage sump throughly by brushing, removing ugly spot, algae by using suitable chemicals as necessary and finally washing with bleaching powder to entire satisfaction of Engineer-in-Charge. Note(ii) T & P, material, involved in pumping out water shall be provided by contractor without any extra cost to the Dept. |
| 70 | M&L for suction sweeping brush holder made up of MS frame,springs to apply sufficient pressure on brushes for smooth cleaning of bottom surface of swimming pool, rubber gasket round the MS frame holder,adjustable spring pressure mechanisam entire holder should have minimum 30Kgs weight all as directed by Engr-in-Charge. |
| 71 | Supply and mixing Trichloroisocyanuric Acid 90 (TCCA 90) (1PPM) In swimming pool through dozing plants all as specified and directed. |
| 72 | Supply and mixing Alginex (10PPM) In swimming pool all as specified and directed to achieve desired parameters. |
| 73 | Supply and mixing Dry Acid In swimming pool all as specified and directed to achieve desired parameters. |
| 74 | Supply and mixing Bleaching powder In swimming pool all as specified and directed to achieve parameters. |
| 75 | Supply and mixing Non Ferric Alum In swimming pool all as specified and directed to achieve desired parameters. |
| 76 | Supply and mixing Caustic Soda In swimming pool all as specified and directed to achieve desired parameters. |
| 77 | Supply and mixing Chlorotex regent In swimming pool all as specified and directed to achieved parameters. |
| 78 | Supply and mixing Crystal copper sulphate (CDH ) In swimming pool all as specified and directed. |
| 79 | Supply and mixing Potential of Hydrogen Solution (PH) In swimming pool all as specified and directed. |
| 80 | Supply and fixing and taking down old unsv of under water lights 14 Watt stainless steel 8mm toughen glass, 1225 lumens,24 V ,water temp rating -10 to +40 degree , IP-68, with drive and one meter cable length and connected items all as specified and directed. |
| 81 | Supply and fix in replacement of Gland rope of 8 to 10 mm for existing motor and valve complete all as specified and as directed |
| 82 | Supply and fix in replacement of Coupling Spider Heavy Duty as per site requirement complete all as specified and directed. |
| 83 | Supply and fix in replacement over load relay 6 to 10 Amps for submersible motor panel board complete all as specified and as directed |
| 84 | Supply and fix in replacement over load relay 9 to 15 Amps for submersible motor panel board complete all as specified and as directed |
| 85 | Supply and fix in replacement over load relay 14 to 23 Amps for submersible motor panel board complete all as specified and as directed |
| 86 | Supply and fix in replacement of MCB TP 40 amps |
| 87 | Attending/Rectification of breakdowns of connected control panels of any capacity as and when required, rates including replacement of petty repairs. |
| 88 | S&F in repairs PVC insulated and FR PVC round sheathed copper conductor(flexible), 1100 volts, conforming to IS 694 of size 1.0 Sqmm 3 core complete all as specified and directed |
| 89 | Dismantling the power supply of electric motor any type including dismantling from pump and taking to workshop with necessary transportation and opening the complete motor and rewinding the rotor with super enameled copper wire as per the existing gauge with necessary insulation, sticks and varnishing, including replacement of shaft bearing 02 Nos and motor terminals plate/cable ducts complete of capacity 25 HP including painting of motor complete all as directed. |
| 90 | Note for item No: 80-89 Pump/Motor shall be dismantled and winding shall be tested continuity at site if winding fail/burnt is established than winding shall be cut at site before issuing gate pass. The coated rate deemed to included .(ii) All u/s Item to be deposit in MES yard and collected after completion of work. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jun 30, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 23, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 15 daysJul 29, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 21 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender