Tender For Special Repairs To Perimeter Fencing And Office Toilets At Stn Hq Dehu Road
Tender Value
12.31 Lakhs
Estimated cost
Bid Submission
22 Jul 2026
10 days left
EMD
24636
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Pune → Maharashtra
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repairs To Perimeter Fencing And Office Toilets At Stn Hq Dehu Road
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling posts of struts (wood, steel or RCC) any section including taking out embedded portion and making good disturbed ground (Natural ground/concrete, brick work) full length of post to be measured complete all as specified and directed by Engineer-in-Charge |
| 2 | Dismantling of chain link fencing wire mesh or any type including barbed wire fencing, folding servicable fencing for reuse complete all as specified and directed by Engineer-in-Charge |
| 3 | Excavation in post holes (or similar hole) each n. exc. 0.5 cum, getting out, returning filling and ramming earth or broken rubble mixed with earth around in layers n. exc. 25cm watering and removing surplus soil to a distance n. exc. 50cm and making good surface in soft and loose soil complete all as specified and directed by Engineer-in-Charge |
| 4 | M & L for PCC 1:3:6 type C-2 (using 40mm graded stone aggregate ) as in foundation concrete for fencing post complete all as specified and directed by Engineer-in-Charge |
| 5 | S & F for angle iron fencing post and struts including cutting tops to shape as directed, drilling holes, notching for wire etc , flat iron fillets ( for securing wire mesh etc) including all necessary drilling, bolting or riveting etc and similar work conforming to Fe-410-0 or Fe 310-0 anyu size.for doors, balusters, nosing to steps including embeding in concrete and screwing etc.complete all as specified and directed by Engineer-in-Charge |
| 6 | S & F for MS Screw bolts ( machine made) with hexagonal or square heads at one end and screwed the other or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut length exc. 5 cm but not exc 10 cm long 5 to 10mm dia of shank etc complete all as specified and directed by Engineer-in-Charge |
| 7 | Supply only chain link MS galvanised fencing incl line wire 50x50mm mesh (12 gauge) size and any type of strands, rails, straining bolts etc incle provn of binding wire all complete all as specified and directed by Engineer-in-Charge |
| 8 | Fixing only chain link fencing any mesh, size and type to any type of standards, rails, straining bolts etc incl provn of binding wire complete all as specified and directed by Engineer-in-Charge |
| 9 | M&L for round bars 10mm dia and over cut to length bent to shape required incl cranking, bending spirally for hoping for columns, hooking ends and binding with and incl MS Wire (annealed) not less than 0.9mm dia or securing with clips etc.complete all as specified and directed by Engineer-in-Charge |
| 10 | M & L for two coats of synthetic enamel paint to new steel surfaces over a coat of red oxide primer surfaces of any description exc 10 cm in witdth or girth complete all as specified and directed by Engineer-in-Charge |
| 11 | M & L for preparing new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer surface area not exc. 10cm in width or girth complete all as specified and directed by Engineer-in-Charge |
| 12 | Supply and fix in repairs galvanized 2 strand steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts including securing or tying at crossings with and provision of galvanized mild steel wire, staples or steel pins etc (each line wire to be measured) |
| 13 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dense soil. |
| 14 | M & L for Cement concrete type D2 1:4:8 using 40mm graded stone aggregate in foundations, filling and mass concrete complete all as specified and ditected by Engr-in-Charge. |
| 15 | Dismantling plain or corrugated steel sheeting,any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed. |
| 16 | Dismanteling MS works of any desc. not otherwise provided for complete all as specified. |
| 17 | Dismantling of PVC water tank of capacity exc 500 ltr but nexc 1000 litre complete all as specified and directed. |
| 18 | Dismantling floor hearth or wall tiling incl cement mortar bedding/plaster (but not backing) and removing rubbish off the premises etc complete all as directed. |
| 19 | Dismantling wall/ ceiling boards(fiber pulp insulation etc.) or insulations boards /slabs/blankets any thickness incl. cover fillets |
| 20 | Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar. |
| 21 | Taking down chowkats or frames with shutters ( without taking off shutters from the frame) exc 1.5 sqm but n.exc 4 sqm each and removing to store. |
| 22 | All as per item No 21 but n'exc 1.5 Sqm each. |
| 23 | M and L for 10 mm thick Polypan PS 20010 Prelam PVC (hallow profile) sheets used for fixing on wall Lining and PVC false ceiling inclusive of necessary fixing as directed by manufacturer and engr-in-charge. |
| 24 | Demolition brick or stone masonary built in cement mortar including all quoins arches pillars etc but excluding ashlars facing dressed stone work and precast concrete block, complete all as specified |
| 25 | Material and labour for Modular Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in and setting in mortar CM 1:6, complete all as specified and as directed by engr-in-charge. |
| 26 | M&L for 15 mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surface and finishing the surface even and smooth without using extra cement secified and directed by Engr-in-charge. |
| 27 | M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces finished even and smooth in cement mortar 1:6, complete all as specified |
| 28 | M&L for preparation of newly plastered surface of wall and applying two coats of distemper oil emulsion over and including 3 mm thick wall care putty and a coat of alkali resistance primer etc. complete all as specified and directed by Engr-in-Charge. |
| 29 | Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces of wall etc. complete all as specified and directed. |
| 30 | M & L for 25 mm thick PCC 1:2:4 type B1, 12.5 mm graded stone aggregate as in flooring including finishing cement concrete rough surface with out using extra cement. |
| 31 | M & L for non skid coloured ceramic tiles 7 to 8mm thick square / rectangular area of each tile exc 0.06 Sqm but not exc 0.11 Sqm as in floor laid over 15 mm thick screed bed in CM 1:6 as in floor etc. set and jointed in neat cement slurry and pointed in coloured cement to match the surface of tile complete all as specified and directed by Engr-in-charge. |
| 32 | M & L for Glazed ceramic coloured tiles of size 350 mm X 450 mm X 7 mm thick as on vertical surfaces such as skirting, dados and rises to steps etc. over 10mm thick rendering in CM 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and directed. |
| 33 | Returning filling in including speading,leveling ,watering and well ramming in layers not exc 25 cm in soils complete all as specified and directed by Engr-in-Charge. |
| 34 | Removing of excavated Soil n exc 50m and depositing where directed at a level n.exc 1.50m above the starting point. |
| 35 | M&L for 50 mm thick PCC 1:3:6 type C2 in plinth protection finishing even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.. |
| 36 | M & L for use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, bands, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished flat surface of concrete complete all as specified and directed. |
| 37 | Supply & Fixing PVC door frame (50x47) mm made out of plain colour 5 mm thich PVC Sheet re in forced with MS Square Tube, supplying & fixing in opening as per specification & drawing |
| 38 | S&F factory made solid panel PVC door shutter 30 mm thick ( Style ) consisting of frame made out of MS Tubes for top & bottom rails.MS frame shall be covered with heat moulded plain colour PVC ' C 'Channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC Sheets for top rail , lock rail & bottomrail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC Sheet to be fitted in the MS Frame welded / sealed to stiles & rails with suitable PVC Sheet beading, jointed together with solvent cement,supplying & fixing in the frame at site as per specification & drawing. |
| 39 | S & F for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed by Engr In Charge. |
| 40 | S&F Rolled Sections as in main croos beams , hip and jack rafters; purlins, where connected to common rafter , posts etc. conf to Fe-410-w(gde E-250 quality-A) etc. use for bracing, staging also complete all as specified and directed by Engr In Charge. |
| 41 | Material & labour for two coats of synthetic enamelled paint over a coat of red oxide on new steel surfaces exc 10cm width or girth including preparation of surfaces.complete all as specified and directed by Engr In Charge. |
| 42 | S&F 1000 Ltrs capacity PVC Rotational Moulded polyethylene water storage tanks (Cylindrical vertical with closed top) double layer hoisted and fixed in position including float valve all as specified and directed by Engr-in-charge.. |
| 43 | M&L for reinforced cement concrete pipes class NP-2 , laid in trenches & jointed complete with collars, dia of pipe 150 mm . |
| 44 | M&L for PCC (1:4:8) type D2 (using 40 mm graded stone aggregate) as in bed to drain pipes, incl packing under & hauching against the sides of pipes after they are laid and tested for 150 mm bore RCC pipe. |
| 45 | S & F in repairs 15 mm dia of pipe Gun-metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed.complete all as specified and directed by Engr In Charge. |
| 46 | S & F in repairs 20 mm dia of pipe Gun-metal, globe or gate valvees with iron wheel head, screwed both ends for iron pipe and fixed.complete all as specified and directed by Engr In Charge. |
| 47 | S&F 16 mm bore CPVC pipe SDR 11 & Plain CPVC SDR 11 fittings with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by Engr In Charge.. |
| 48 | S&F 20 mm bore CPVC pipe SDR 11 & Plain CPVC SDR 11 fittings with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by Engr In Charge. |
| 49 | Supply and fix in repairs for Single piece WC with UF soft close seat cover, Hinges, dual flush cistern fittings, fixing accesssories and accessories set size : 360 x 730 x 740 mm (Cat No. SLS-WHT-6851S300UF Make;- Jaguar) etc complete all as specified and as directed. |
| 50 | S & F Angular stop cock with wall flange (Cat No- CON-053KN, Make - Jaguar) fancy type chromium plated, screwed down, screwed both ends for iron pipe or for unions and fixed etc, complete all as specified and directed by Engr In Charge. |
| 51 | S & F for Thin Rim Table Top Wash Hand basins, Shape round, size 595 x 445 x 135 mm, (Cat No. JDS-WHT-25931, Make;- Jaguar) including cutting for and pinning in ends of brackets or erecting stand,(but including of supply, waste pipe, taps) complete all as specified and directed. |
| 52 | S&F in repairs bib cock 15 mm dia with wall flange(Cat No- KUP-35037PM, Make- Jaguar) fancy type chromium plated, screwed down, screwed for iron pipe or for brass ferrule and fixed. complete all as specified and directed by Engr In Charge. |
| 53 | S&F in repairs 15mm dia stop valves , fancy type chromium plated, screwed down, screwed both ends for iron pipe or for unions and fixed. complete all as specified and directed by Engr In Charge. |
| 54 | Supply & fixing 15mm pillar cock Single lever basin mixer with popup waste with 450 mm long Braided hoses, ( Cat No. KUP-35051BPM, Make : Jaguar) cast copper alloy, with capstan heads, chromium plated, screwed down , high pressure, with or without lettered 'Hot' or Cold' with long screwed shanks and fly nuts, screwed for iron pipe and fixed. Bore of pipe in 15mm complete all as specified and directed by Engr In Charge.. |
| 55 | S&F for waste coupling of PTMT for 32 mm bore dia of discharge pipe (half or full threaded) Minimum weight 32mm-45gms/40mm-60 gms) |
| 56 | S&F PVC connections 15mm size with PTMT nuts of length 600mm etc. complete all as specified and directed by Engr In Charge. |
| 57 | S & F Towel Rack 600 mm long with lower hangers (Cat No. CPA-1181, Make- Jaguar) etc. complete all as specified and directed by Engr In Charge. |
| 58 | S & F Towel Ring Square with round flange (Cat No. CPA-1121, Make- Jaguar) etc. complete all as specified and directed by Engr In Charge. |
| 59 | S & F Soap Dish holder (Cat No. CAN-1131N, Make- Jaguar) etc. complete all as specified and directed by Engr In Charge. |
| 60 | S & F Paper holder with Flap Recessed type stainless steel (Cat No. AHS-1553, Make- Jaguar) etc. complete all as specified and directed by Engr In Charge. |
| 61 | S & F Corner glass shelf (with bracket) (Cat No. CAN-1173, Make- Jaguar) etc. complete all as specified and directed by Engr In Charge. |
| 62 | S & F Swivel mirror 630 x 445 mm Rectangular shape (Cat No. AKP-35795, Make- Jaguar) etc. complete all as specified and directed by Engr In Charge. |
| 63 | S & F two way bib cock with wall flange (Cat No. ALI-85041, Make- Jaguar) complete all as specified and directed. |
| 64 | S & F cast iron Nahani trap 75mm out let dia with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4).. |
| 65 | S&F C I floor trap 75mm out let dia with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4).. |
| 66 | M & L for Gully traps salt glazed stoneware (SGSW) square or round mouthed type 'P' of size 180x100mm for drain pipes complete all as specified and directed. |
| 67 | S & F 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in floors or trenches. |
| 68 | S & F 75 mm dia bore PVC (SWR) pipes single socketed , in any length with rubber ring joints , laid in trenches or in floors |
| 69 | S & F 75 mm dia bore PVC (SWR) bends any radius |
| 70 | S & F 110 mm dia bore PVC (SWR) bends any radius |
| 71 | S & F 110 mm dia bore PVC (SWR) junction single 'T' equal or unequal |
| 72 | S & F PVC (SWR) 110 mm bore vent cowl |
| 73 | Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar. |
| 74 | M&L for Machine cut cudappah stone slab 20-25mm thick over cement screed base, laid and jointed with grey cement slurry mixed no pigment to match the shade of the slab including rubbing and polishing, screed bed of mortar 15 mm thick in cement mortar (1:6) for laying floor finishes complete all as specified. |
| 75 | Material and labour for 20mm thick granite (of any type) work ( table rubbed and polished) in steps , jambs. pillars, window cills, cooking platforms and like in cement mortar (1:4), pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite screed bed of mortar 15 mm thick in cement mortar (1:6) for laying floor finishes complete all as specified and as directed. |
| 76 | Supply and fix inrepair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 77 | S&F for pressed steel door frames with one or more rebates incl necessary fixing lugs, hinges, lock strike plates of size 105 X 60mm. |
| 78 | S & F for 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides |
| 79 | M & L for two coats of synthetic enamel paint to new steel surfaces over a coat of red oxide primer surfaces of any description exc 10 cm in witdth or girth complete all as specified and directed by Engineer-in-Charge |
| 80 | M & L for Preparation of wooden surfaces and applying two coats of synthetic enamel paint over a coat of pink primer surfaces of any description exc 10 cm in witdth or girth complete all as specified and directed by Engineer-in-Charge |
| 81 | S & F of 100 mm long aluminium anodised barrel tower bolt complete all as specified and directed. |
| 82 | S & F of 100 mm long extruded anodised aluminium alloy handle, complete all as specified and directed. |
| 83 | S&F 100 mm MS, Butt hinges,medium weight cold rooled fixed with screw or welding complete. |
| 84 | S & F of 250 mm long (Length of bolt) aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolt or cast aluminium alloy complete all as specified and directed. |
| 85 | S/F anodised aluminium window and ventilator shutters including frames ,(three track) fixed type without sash bar ,aluminium section weighing 0.55 kg/m. including necessary joining cleats ,glazing clips,rubber packing,anodised aluminium snap beading,screw with powder coating of any colour (thickness of powder coating not less than 50 micron ) including stainless steel wirecloth 0.36 mm nominal dia of wire and avg. aperture 1.40 mm and fixed with stainless steel wire staples and 3.0 mm th. sheet glass ordinary quality plain and glaizing complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 01, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 22, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 10 daysJul 23, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 11 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender