Tender For Provision Of S Le Room And Ladies Washroom For Mes Office Naval Base Karwar.
Tender Value
36.40 Lakhs
Estimated cost
Bid Submission
21 Jul 2026
14 days left
EMD
72800
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Uttara Kannada → Karnataka
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provision Of S Le Room And Ladies Washroom For Mes Office Naval Base Karwar.
BOQ
| Sl. No. | Item Description |
| 1 | M&L for surface dressing not exceeding 15 cm deep in hard/dense soil all as specified and directed. |
| 2 | Excavation in trenches n.exc 1.5m wide and n.exc 1.5m depth for foundation etc and getting out in hard/dense soil all as specified and directed. |
| 3 | M&L for PCC (1:4:8), type-D2 using 40 mm graded stone aggregate as in foundation filling and mass concrete all as specified and directed. |
| 4 | M&L for moorum/red bajri filling in floors or paving's, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering |
| 5 | M&L for hardcore of broken stone or boulders of gauge not exceeding 63mm and deposited spread and levelled in layers not exceeding 15cm thick watered and rammed to true surface. |
| 6 | M&L for cement concrete (1:2:4) type B-0, using 12.5mm graded stone aggregate, 40mm thick as in DPC all as specified and directed. |
| 7 | M&L for pre-cast cement concrete blocks (1:2:4), type B1 masonry with solid blocks, exc. 10cm in width and setting in CM (1:4) all as specified and directed. |
| 8 | M&L for mild steel TMT (CRS/ HCRM) bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia all as specified & directed. |
| 9 | M&L for mild steel TMT (CRS/ HCRM) bars 5 to 8mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia. |
| 10 | M&L for RCC design mix M 30 using 20mm graded stone aggregate as in foundations, footings, plinth beams etc all as specified and directed. |
| 11 | M&L for RCC design mix M 30 using 20mm graded stone aggregate as in columns, pillars, piers etc all as specified and directed. |
| 12 | M&L for providing cement concrete design mix M 30 using 20mm graded stone aggregate as in beams, cantilevers, bressummers lintels over 1.5m clear span including necessary form work complete all as specified and directed. |
| 13 | M&L for providing cement concrete design mix M 30 using 20mm graded stone aggregate as in chajjas including necessary form work complete all as specified and directed. |
| 14 | Use & waste of form work to sides of concrete foundation, footings, plinth beams etc rough finished surfaces all as specified and directed. |
| 15 | Use & waste of form work to sides of pillars, columns etc rough finished square or rectangular surfaces all as specified and directed. |
| 16 | Formwork to sides and soffits of floor or roof beams, lintel etc all as specified and directed. |
| 17 | Returning, filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm in hard/dense soil all as specified and directed. |
| 18 | Removing excavated material n. exc 50 m and deposited where directed at a level not exc 1.5 m above the base as in soil. |
| 19 | M&L for plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe 410 -W (Gde- E- 250) quality-A, complete all as specified and directed. |
| 20 | S&F joist, channel, angle, or tee sections in vertical posts, fixed independently, with/ without connecting plates, & column bracings etc. confirming to Fe-410-w or E-250 quality A complete all as specified and directed. |
| 21 | S&F rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides fixed with angle cleats or other connecting plates confirming to Fe-410-w or E-250 quality A complete all as specified and directed. |
| 22 | S&F wind ties for roof including securing bolts, and similar work conforming to Fe-290, Gde E 165 complete all as specified and directed. |
| 23 | M&L for applying two coats of synthetic enamel paint using mechanical spray (maximum working pressure of 3300 PSI) over a coat of red oxide zinc chrome primer including preparation of new steel surfaces of any description exc 10cm in width or girth complete all as specified and directed. |
| 24 | M&L for pre-painted galvalume aluminium zinc coated GI based corrugated steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 25 | M&L for pre-painted galvalume aluminium zinc coated GI based plain steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in ridge, roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed |
| 26 | M&L for rendering 15 mm thick in cm (1:6) on fair faces of concrete surfaces finished even & smooth without using extra cement complete all as specified and directed. |
| 27 | M&L for rendering 10mm thick in cm (1:4) on fair faces of brick work or concrete surfaces for backing coat of wall tiles etc all as specified & directed. |
| 28 | M&L for rendering 5mm thick in cm (1:4) on fair faces of concrete surfaces of ceiling, finished even & smooth using extra cement all as specified and directed. |
| 29 | S&F solid PVC door frame of size 50mmx 47mm made out of 5mm wood grains printed PVC sheet, reinforced with MS square tube and edges painted to match with printed sheet complete all as specified and directed. |
| 30 | S&F factory made solid panel PVC door shutter 30 mm thick (styled) consisting of frame made out of MS tube for top & bottom rails, MS frame shall be covered with heat moulded wood grain printed PVC \\"C\\" channel having a 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and wood grain printed colour PVC sheet for top rail, lock rail and bottom rail on either side & as gap inserted for top rail and bottom rail, panelling of wood grain printed colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with decorative PVC beading of 10mm x 10mm (90 degree) and jointed together with solvent cement supplying and fixing in the frame at site all as specified and directed. |
| 31 | M&L for powder coated Aluminium frame and shutter for doors, sliding windows & ventilators (moveable louvers type) and for partitions with one or more rebates including joining cleat for fixing etc. Rubber gasketing all round the panels/ shutters to fix glass, PVC gasketing in all channels, locking arrangement, (minimum thickness of powder coating 50micron) complete all as specified. |
| 32 | S&F powder coated aluminium (minimum thickness of powder coating 50 micron) door shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc. complete all as specified. |
| 33 | S&F powder coated aluminium (minimum thickness of powder coating 50 micron) window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified. |
| 34 | S&F 4.0 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sq. m in each pane fixed to Aluminium windows/ventilator etc complete all as specified and directed. |
| 35 | S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed |
| 36 | M&L for 18mm thick PVC ply board/ sheets both sides plain as in door shutter, partition, drawers & shelves including solvent cement & beadings etc as per manufacturers instructions complete all as specified and directed. |
| 37 | S&F 100 mm butt hinges, mild steel, with mild steel hinge pin, bright polished and fixed, type B-11 |
| 38 | S&F 150 mm long aluminium anodized barrel tower bolts of extruded sections as fixed complete all as specified and directed. |
| 39 | S&F 300 mm long aluminium alloy anodized sliding door bolts with hasp and staple (bolt type), including fixing clips, fixing bolts and sliding bolts (extruded/cast aluminium alloy), complete all as specified and directed. |
| 40 | S&F 150mm extruded aluminium alloy handles, cast type as fixed complete all as specified and directed. |
| 41 | S&F aluminium (die cast) body, door closer, hydraulically regulated designation No.3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg all as specified and directed |
| 42 | S&F double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty all as specified and directed. Please Enable Macros to View BoQ information |
| 43 | S&F double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jun 30, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 21, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 14 daysJul 23, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 16 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender