Tender For Repair/Maint To Interlocking Paver Blocks, Chequered Tiles And Hard Standing And Comprehensive Maintenance Of B/R And E/M Services At Various E/M Installations At Technical And Residential Area Of Irde Under Ge(I) R&D Dehradun
Tender Value
45.08 Lakhs
Estimated cost
Bid Submission
20 Jul 2026
10 days left
EMD
90200
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Dehradun → Uttarakhand
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair/Maint To Interlocking Paver Blocks, Chequered Tiles And Hard Standing And Comprehensive Maintenance Of B/R And E/M Services At Various E/M Installations At Technical And Residential Area Of Irde Under Ge(I) R&D Dehradun
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of stone slab and tiles laid dry or laid dry and pointed in any mortor of any description or thickness in floor, aprons etc complete all as specifed and directed. |
| 2 | M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc.of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 3 | M&L for glossy finish rubber moulded chequered cement concrete tile 30 cm x 30 cm x 25 mm thick set jointed and pointed in neat cement slurry in floor with grey cement and pigment to match over and including 15mm thick screed bed or bedding layer of cement mortar 1:6 for laying floor finished complete all as specified and directed. |
| 4 | Demolition of cement concrete (unreinforced) of anay description as in ground floors and pavings not exceeding 15cm thickness (above or below ground floors) complete all as specified and directed. |
| 5 | M&L for 100mm thick cement concrete type C-2, 1:3:6 (using 40mm graded crushed stone aggregate) as in sub floor complete all as specifed and directed. |
| 6 | M&L for providing 75mm thick PCC 1:3:6, type C-2 (using 40mm graded stone aggregate) as in plinth protection /floor finished even and fair incl making expansion joints and filled with bitumen and sand complete all as specified and directed. |
| 7 | M&L providing 100mm thick PCC (cement concrete) 1:2:4 etc type B-2 (using 40 mm graded stone aggregate ) pavement/ramp/floor finsihed even an smooth without using extra cement complete all as specified and directed. |
| 8 | Demolition of cement concrete (reinforced) of any description and in any position complete all as specified and directed. |
| 9 | M&L for reinforced Precast cement concrete(1:2:4) type B-1 using 20 mm graded stone aggregate as in landing , cover slab (for manholes, shelves), chullah hoos, chajjas, water troughs , mangers, shelves an similar articles with plain faces incluing necessary form work , & set in Cement Mortar ( 1:4 ) complete all as specified an directed. |
| 10 | M&L for Mild Steel TMT bar, 10 mm dia & over, cut to length, bent to shape require, incluing cranking , bending spirally for hooping for columns ,hooking endsa and binding with Mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed. |
| 11 | Taking down cement or cement lime plaster, any description on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc with and including removing of debrish taking down plaster out side M.D land complete all as specified and directed. |
| 12 | M&L for Rendering 15mm thick in CM (1:4) on fair faces of brick masonry/ concrete surface on wall with using liquid water proofing compound and finishing the surfaces even and smooth without using extra cement , complete all as specified an directed.Note:- WPC shall be measured & paid for separately as “Supply only item under respective items of Sch \\"A\\"/BOQ |
| 13 | Supply only Liquid water proofing compound |
| 14 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specifed and directed. |
| 15 | M&L for preparing old surfaces of walls plastered plastered by complete removal of existing treatment by electric grinder brooming down with steel or wire brush and scraping down smoke soot, moulds moss & efflorescent salt and trading oil and greasy spots , washing rubbing down and stopping of distempered and painted surface & removing all vegetation growth, nails and making good holes,cracks etc complete by necessary putty and make the surface smooth by rubbing with sand papers etc and applying Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 5489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required hade (Company Depot Tinted) with silicon additive @ 1.43 litre/ 10 sqm over and complete all as specified and directed. |
| 16 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete all as specifed and directed. |
| 17 | Dismantling wrought iron or mild steel work of any description not otherwise described and removal of dismantling materials with and including, removing debris outside MOD Land at contractor is own arrangement , complete all as specified and directed. |
| 18 | M&L for stainless steel framed work such as in grills, gratings, etc. with end of bars shouldered and/or riveted , or forged in to spikes, framed guard bars, barred iron doors, ladders, framed blusters, walk ways, railings, framework of water tanks and similar work complete all as specified and directed. |
| 19 | Demolition of brick or stone boulder masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone works and precast concrete articles with and including, removing debris outside MOD Land at contractor is own arrangement complete all as specified and directed |
| 20 | M&L for brick work with sub class 'B' bricks, straight or curved on plan exc 6 mtr mean radius built in cement mortar 1:6 complete all as specified and directed. |
| 21 | M&L for preparation of new or previously untreated steel surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 22 | Disconnecting & taking down existing water tank of capacity exc 250 liter and not exc. 500 liter and removing from site complte and S&F rotational moulded polyethylene water storage tanks 500 lts capacity (cylindrical vertical with closed top) hoisted with and including 20 mm dia ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipe or for brass ferrule and fixed in position all as per SSR Part I complete all as specified & directed. |
| 23 | Disconnecting & taking down existing water tank of capacity exc 500 liter and not exc. 1000 liter and removing from site complte and S&F rotational moulded polyethylene water storage tanks 1000 lts capacity (cylindrical vertical with closed top) hoisted with and including 20 mm dia ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipe or for brass ferrule and fixed in position all as per SSR Part I complete all as specified & directed. |
| 24 | Removing of old treatment from old concrete floor/terrace taking down existing detoriated / decayed tarfelt or any treatment including loose surface, scraping with scraper, chiseling.scraping of surface with wire brush of any other method. sweeping clean & washing down with water to remove dust etc. and removing the scraped materials debris to a distance not exc. 1000 m complete all as specifed and directed. |
| 25 | M&L 25 mm thick PCC (1:2:4) type B-0, (using 12.5 mm graded crushed stone aggregate) complete all as specified and as directed. |
| 26 | M&L 10mm thick cement plaster on fair face of concrete surface including repair of doubing roof surfaces in CM 1:3 finished even land smooth without using extra cement over complete all as specified and directed.(Note: Water proofing compound shall be measured and paid sepratly ) |
| 27 | Wire brushing and cleaning top surface of tiles, lime terracing or cement concrete, including flashings and junction of parapets, etc., and surface painting, with a layer of blown grade bitumen of any penetration applied hot @ 1.7 kg per sq. m, blinded with grit or pea size gravel @ 0.006 cu.m per sq.m, and lightly tampered complete all as specified and directed. |
| 28 | S&F APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster matt black finished non woven fabric (wt. not less than 150 gms/sqm) over compatible primer at 0.40 ltr/sqm of density at 25 degrees centigrade 0.87-0.89kg/Ltr and viscosity 70-160 cps or cold sticker and butane torch application of membrane with 10cm overlap both ways after necessary preparation of surface complete all as specified and directed by Engr-in-Charge. |
| 29 | M&L for Heat resisting paint on Surfaces of any description wood, steel, iron, concrete, brick, stone, etc., exceeding 10cm in width or girth complete all as specified and directed by Engr-in-Charge. |
| 30 | M&L for Cement concrete tiles with grey cement pigment 25cm x 25 cm x 22mm thick, with size of chips upto 6 mm; set jointed and pointed in neat cement slurrynin floors, and cut and polished complete all as specified and directed. |
| 31 | M&L for preparing of old painted wooden surfaces over 10cm width or girth and making good including knotting and stopping,cleaning etc complete by necessary putty and make the surface smooth by rubbing with sand papers etc and applying one coat of synthetic enamel paint on old prepared surfaces of wooden complete all as specified and directed. |
| 32 | M&L for preparing old surfaces of walls plastered plastered by complete removal of existing treatment by electric grinder brooming down with steel or wire brush and scraping down smoke soot, moulds moss & efflorescent salt and trading oil and greasy spots , washing rubbing down and stopping of distempered and painted surface & removing all vegetation growth, nails and making good holes,cracks etc complete by necessary putty and make the surface smooth by rubbing with sand papers etc and applying two coats of approved shade of oil emulsion distemper, complete all as specified and directed |
| 33 | Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing tiles and rubbish off the premises, complete all as specified and directed. |
| 34 | M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed in CM 1:6 complete all as specified and directed by Engr-in-Charge. |
| 35 | Description all as per Srl item No. 34.00 here in before but on vertical surfaces such as skirting incl including 10mm thick rendering in cement mortar 1:4 rough finish to receive the tiles complete all as specified and directed. |
| 36 | M&L for glazed coloured ceramic tile ,first quality( of approved class , colour and design/ shade ) of size 300 x 450 / 350x450 / 350x250 thick in vertical surfaces, as in dado / skirting etc set & jointed in neat cement slurry & pointed in coloured cement to match with coloured tiles, over with and including 10 mm thick rendering in cement mortar (1:4), rough finish to receive the tiles complete all as specified and directed. |
| 37 | M&L Machine cut kota stone 40-50mm slab cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engr-in-Charge. |
| 38 | Description all as per Srl item No. 37.00 here in before but in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. |
| 39 | M&L for two coats of cement based paint over a coat of primer on newly plastered surfaces of walls including preparation of surfaces complete all as specified and directed. |
| 40 | M&L rendering 15mm thick cement plaster in cement mortar (1:6) finished even & smooth without using extra cement on brick/concrete surfaces complete all as specified and directed. |
| 41 | M&L for Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on new work over a coat of primer on newly plastered surfaces of walls including preparation of surfaces complete all as specified and directed. |
| 42 | M&L for two coats of oil bound distemper over a coat of primer on newly plastered surfaces of ceiling including preparation of surfaces complete all as specified and directed. |
| 43 | M&L for preparing old surfaces of walls plastered plastered by complete removal of existing treatment by electric grinder brooming down with steel or wire brush and scraping down smoke soot, moulds moss & efflorescent salt and trading oil and greasy spots , washing rubbing down and stopping of distempered and painted surface & removing all vegetation growth, nails and making good holes,cracks etc complete by necessary putty and make the surface smooth by rubbing with sand papers etc and Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats over a coat of primer on including preparation of surfaces complete all as specified and directed. |
| 44 | M&L for prepation of old painted wooden based surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint, complete all as specified and directed by Engr-in-Charge. |
| 45 | M&L for preparation of old painted steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint, complete all as specified and directed by Engr-in-Charge. |
| 46 | M&L RCC type B1 (1:2:4) nominal mix using 20 mm graded aggregate in Chajjas of any height complete all as specified and directed. |
| 47 | M&L for Formwork to chullah hoods, chajjas, troughs & similar items including edges Rough finished surfaces of concrete flat of any height complete all as specified and directed. |
| 48 | S&F in repair for 600x450mm beveled edge looking mirror of selected quality glass 4 mm thick mounted on 6mm thick AC building board or commercial ply wood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified & directed. |
| 49 | S&F in repair Bib taps long body cast copper alloy chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified and directed. |
| 50 | S&F in repair PVC connections 15mm size with PTMT nuts of length 300mmcomplete all as specified and directed. |
| 51 | S&F in repair fancy type, stop cock regular body 15 mm nominal bore with flange, brass, chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butterfllly handles, screwed both ends for iron pipe or for brass ferrule or to GI socket complete all as specified and directed. |
| 52 | S&F in repair pillar taps, brass, with capston heads, fancy type chromium plated, screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and fly nuts screwed for 15mm bore iron pipe and fixed complete all as specified and directed. |
| 53 | Taking up or down steel tubing and connections 15mm bore complete all as specified and directed. |
| 54 | Taking up or down steel tubing and connections 20mm bore complete all as specified and directed. |
| 55 | M&L for Cutting chases not exc 10cm girth in brick walls for concealed water tubings and making good, complete all as specified and directed. |
| 56 | S&F Steel water tubes, medium grade, ISI marked, galvanised, 15mm bore with all fittings, fixed to walls and ceiling or laid in floors complete all as specified and directed. |
| 57 | Description all as per item Srl No. 56.00 here in before but 20mm bore. |
| 58 | S&F in repair PVC low level flushing cistern 10 Ltr capacity with & including brackets for fixing to walls complete and PVC flush pipe of LDPE pipe of pressure rating 6 kg (f)/ sq.cm complete all as specified and directed. |
| 59 | S&F vitreous china wash hand basin (flat back) of size 550x400mm including one number chromium plated waste fittings, 32 mm dia waste pipe, brass with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed, with & including 32 mm dia PVC waste pipe with connector, MS brackets 2 numbers including cutting for and pinning in ends of brackets complete all as specified and directed. |
| 60 | S&F in repair white vitreous China wash down water closet pan (pedestal) pattern, and trap (excluding) fixing bolts, flushing cistern and flush pipe) including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc. with and including plastic water closet sheet covers white closed pattern with flat bottom, with mild steel chromium plated or aluminised hinging device and 15mm dia chromium plated brass washing jet fixed to water closet with 15mm dia and 1.2m to 1.5m long flexible pipe with chromium plated spring type cover complete with fixing arrangement fancy look complete all as specified and directed. |
| 61 | Taking down Cast iron/PVC pipe of any dia and size fixed on wall or floor including all fittings complete all as specified and directed. |
| 62 | S&F PVC (SWR) 110mm pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. |
| 63 | S&F PVC (SWR) 75mm pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. |
| 64 | S&F PVC (SWR) 110mm pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed. |
| 65 | S&F PVC (SWR) 75mm pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed. |
| 66 | S&F 110 mm dia PVC(SWR) bends/ shoes any radius complete all as specified and directed. |
| 67 | S&F 75 mm dia PVC(SWR) bends/ shoes any radius complete all as specified and directed. |
| 68 | Taking down chowkats or frame of any description nexc 1.5 Sqm each with shutter(without taking off shutters from the frames) & remove off the premises complete all as specified and directed. |
| 69 | Taking down chowkats or frame of any description exc 1.5 Sqm each and n.exc 4Sqm with shutter(without taking off shutters from the frames) & remove off the premises complete all as specified and directed. |
| 70 | Taking down shutter exc. 1 Sqm and n.exc 2 Sqm each shutters of any description. complete all as specified and directed. |
| 71 | S&F solid PVC door frame of size 50mmx 47mm made out of 5 mm plain/ colour PVC sheet reinforced with MS square tube as per specification & drawings specified in SSR Part-II 2020 complete all as specified and directed. |
| 72 | S&F Factory Made Solid PVC Moulded Door Shutter of any colour (as approved by GE) with particle board core 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed. |
| 73 | S&F first class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, all as specified and directed by Engr-in-Charge. |
| 74 | S&F 40 mm thick first class hard wood plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, etc are provided with stiles and rails as specified in SSR Pt I Section 8, clause 8.24 (a) complete all as specified and as directed. |
| 75 | S&F factory made glazed and Skelton 35mm thick second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc divided into squares, with plain, chamfered or rounded,mitred and rebated sash bars, any numbers , edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc; sizes of members of shutters as specified in SSR Part-I section 8, clause 8.24 (b) complete all as specified and directed. |
| 76 | S&F stainless steel wire cloth 1.23 mm nominal dia of wire and size of mesh 12 mm and fixed with tinned tacks or galvanized steel wire staples complete all as specified and directed. |
| 77 | M&L for preparation of new or previously untreated wooden surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and directed. |
| 78 | S&F aluminium anodised barrel tower bolt of extruded section 150 mm long and fixed complete all as specified and directed. |
| 79 | S&F 100 mm size mild steel butt hinges, ISI marked, medium weight, cold rolled and fixed with screws/welded to frame complete all as specified and directed. |
| 80 | S&F aluminium handles, cast type, anodised 150 mm size complete all as specified and directed. |
| 81 | S&F Aluminium alloy, anodised, sliding door bolt 300mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy, fixed in repairs complete all as specified and directed. |
| 82 | S&F powder coated 3 track aluminium sliding window three track with two glass shutters using 4 mm thick glass tinted modi guard and one shutter with stainless steel wire gauge wire cloth 0.31 mm stainless steel wire gauge wire cloth 0.31 mm nominal dia of wire and width of aperature 1.61 mm using aluminium powder coated section aluminium cleat, PVC track, beading handle, lock, rubber beading etc complete fittings as per manufacture instructions complete all as specified and directed. |
| 83 | S&F in repair 1.25mm thickness of laths steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, haps and staple and one shop coat of primer erected in position as indicated, complete push pull or manual type complete all as specified and directed |
| 84 | Excavation in trenches, n.exc 1.5m wide and n.exc 1.5m depth in soft/loose of soil for foundation, etc. or for shafts, wells cesspits, manholes, pierholes etc and getting out complete all as specified an directed. |
| 85 | M&L 100 mm thick for cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in sub base for laying floor finishes complete all as specified and directed. |
| 86 | M&L for returing filling in soft/loose soil, including spreading, levelling, watering and well ramming in layers not exc 25cm thick complete all as specified and directed. |
| 87 | Removing of excavated material (Soil) to a distance exc 250m but not exceeding 500 mtr and depositing at a level n.exc 1.5 m above the starting points complete all as specified an directed. |
| 88 | M&L for welded Wire netting of galvanised steel wire, 1.40mm dia size of mesh 20mm fixed to wood or steel members complete all as specified and directed. |
| 89 | Taking down carefully unservicable ball bearing from rolling shutters and S&F ball bearing heavy duty as required size at approprite place, match the existing of gear operated type rolling shutter complite all as specified and directed. |
| 90 | Taking down carefully unservicable safety lever mild steel lock any type from rolling shutters and S&F new safety lever mild steel lock 4 lever heavy duty as required size at approprite place, match the existing of gear operated type rolling shutter complite all as specified and directed. |
| 91 | Disconnecting and Taking out old unserviceable LT Panel any type and shape, size, and Supply, installation, testing and commissioning out door type factory made kisok cubicle type, dust and vermin proof of suitable size IP class protection made of 3mm thick CRCA sheet and angle iron 50X50X6mm frame, TPN aluminium busbar mounted in porcelin insulator duly drilled hole for cable connection including front and rear side opening with locking arrangement and provn for incoming and outgoing cables with glands including control wiring with minimum 1.5 sqmm PVC insulated copper conductor for measuring of voltage, amp with indicators RYB, painting with two coat of smoke grey synthetic enamelled paint over a coat of red oxide primer on PCC platform 100 mm thick made out of PCC 1:3:6, 1 mtrs all round the panel board suitable for 3 phase 4 wire 415 V, 50 Hz factory fabricated in an approved factory having modern fabrication and comprising of following :- |
| 92 | (i) Incoming :- (a) MCCB , 400 Amps, 4 pole, 415 Volts, AC supply, having breaking capacity , 36 KA drawout typed with microprocessor release IPR E , Qty – 01 (b) Digital Ammeter 3 Phase AC 0 – 1000 Amps, with 3 current transformer of suitable ratio and capacity Qty -01 No. (c) Indicating lamps LED type for three phases -R Y B of 3 Nos,(d) Digital Voltmeter 3 Phase AC 0 – 500 Volts.Qty -01 No.(e) Aluminium bus-bar of 630 Amps rating TPN -01 Set |
| 93 | (ii) Out Going :-a) MCCB, 250 Amps, 4 pole, 415 Volts, AC supply, having breaking capacity , 25 KA with adjustable thermal & fixed magnetic setting, Qty – 01 No. |
| 94 | (b) MCCB, 100 Amps, 4 pole, 415 Volts, AC supply, having breaking capacity , 25 KA with adjustable thermal & fixed magnetic setting, Qty – 3 Nos Please Enable Macros to View BoQ information |
| 95 | (b) MCCB, 100 Amps, 4 pole, 415 Volts, AC supply, having breaking capacity , 25 KA with adjustable thermal & fixed magnetic setting, Qty – 3 Nos Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jun 30, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 20, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 10 daysJul 22, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 12 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender