Tender For Special Repairs To Joinery To Bldg No P-687 Map Phase Ii At Brichgunj Mil Stn, Svp
Tender Value
44.60 Lakhs
Estimated cost
Bid Submission
21 Jul 2026
12 days left
EMD
90000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
South Andamans → Andaman And Nicobar Islands
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repairs To Joinery To Bldg No P-687 Map Phase Ii At Brichgunj Mil Stn, Svp
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (un reinforced) in ground floors and pavings not exc. 15cm thickness etc below or above ground level incl floor hearth tiles if any and removing the rubbish off the premises complete all as specified and as directed by Engr-In -Charge. |
| 2 | Dismantling of floor, hearth or wall tilling incl cement mortar bedding (but not backing) and removing the rubbish off the premises complete all as specified and as directed by Engineer -in-Charge. |
| 3 | Taking down cement plaster of any description incl raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and as directed by Engineer-in-Charge. |
| 4 | Taking down chowkats or frames with shutters area exc 1.5 Sqm but n.exc. 4.0 Sqm each(without taking off shutters from the frame) complete all as specified and as directed by Engineer -in-Charge. |
| 5 | Dismantling boarding, any description, fixed in any position with nails complete all as specified and as directed. |
| 6 | Dismantling of Structural steel work including doors, gates but excluding framed truss etc compete all as specified and as directed by Engineer -in-Charge. |
| 7 | Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed complete all as specified and as directed by Engr-In-Charge. |
| 8 | Materials and labour for PCC 1:4:8, type D2, using 40 mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed. |
| 9 | M&L for Rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finishing the surface even and smooth without using extra cement, complete all as specificed and as per directed by Engineer-in-Charge. |
| 10 | Materials and labour for coloured non skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exc 0.06 sqm n.exc 0.11 sqm, in floors etc set and jointed in neat cement slurry in floors and pointed with coloured cement to match the colour of tiles incl screed bed or bedding layer of mortar 10mm thick in CM 1:4 for laying floor finishes complete all as specified and as directed by Engineer -in-Charge. |
| 11 | M & L for Glazed ceramic tiles in vertical surface 300x 200x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 10mm thick backing coat in Cm 1:3 all as specified and as directed by Engg-in-Charge |
| 12 | Materials and labour for Granite stone slab 18-20mm thick (of any type and coloured in single peice ) work (table rubbed and polished) in steps, jambs, pillars, window cills, flooring, cooking platform machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite including griding and polishing types over & including screed bed 20mm thick in CM 1:4 complete all as specified and directed by Engineer-in-Charge. |
| 13 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/window/ceosetory windows and other Frames/chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibres (wood powder/rice husk/wheat husk) and non toxic additives (maxium toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minium frame density of 750 kg/Cum, screw withdrawal strength of 2200 N (face) and 1100 N (Edge), minium compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of bearing termite/ borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in- Charge. (M.S. hold fast/lugs or SS dash fasteners shall be paid for separately.) Note:- For WPC soild door/Windows frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.) complete all as specified and as directed. |
| 14 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/window/ceosetory windows and other Frames/chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibres (wood powder/rice husk/wheat husk) and non toxic additives (maxium toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minium frame density of 750 kg/Cum, screw withdrawal strength of 2200 N (face) and 1100 N (Edge), minium compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of bearing termite/ borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in- Charge. (M.S. hold fast/lugs or SS dash fasteners shall be paid for separately.) Note:- For WPC soild door/Windows frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.) complete all as specified and as directed. |
| 15 | S&F Factory made single extruded WPC (Wood Polymer Composite) Solid decorative type flush door shutter of 30 mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), Calcium carbonate and natural fibres (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) and 900 N (Edge), minimum compressive strength 50 N/mm2, modulud of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as per specified and as directed. |
| 16 | S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30 mm thick (Stiles), with 2, 4, or 6 raised panel design with 2mm thick moulded prelam PVC sheet on the front face & 2mm thick plain colour PVC sheet on back face with Particle board Core, in frame at site as per specification & drawing. |
| 17 | Supply and fix factory made Wire gauged PVC solid wood grain printed door shutter 30mm thick (style) i.e panel will be of wire gauge in lieu of single prelam PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S Solid tube and this tube shall be welded to M.S tubes. The wire gauze shall be stretched to tighten firmly consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC `C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles with suitable PVC sheet beading, and joined together with solvent cement, in the frame at site as per specification & drawing in SSR complete all as specified and directed by Engineer -in-Charge. |
| 18 | S&F Aluminium snake guard comprising nylon bristle duly secured with aluminium flat section of minimum width 30 mm and length 900 mm fixed to bottom rail of door shutter using aluminium screws complete all as specified and as directed. |
| 19 | S&F Butt hinges, 100mm length medium weight cold rolled mild steel and fixed, complete all as specified and directed by Engineer-in-Charge. |
| 20 | S&F Butt hinges, 75mm length medium weight cold rolled mild steel and fixed, complete all as specified and directed by Engineer-in-Charge. |
| 21 | S&F Aluminium alloy 300mm long, anodised, sliding door bolt with hasp & staple (Bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section of cast aluminium alloy complete all as specified and as directed by Engineer -in-Charge. |
| 22 | S&F Aluminium alloy 200mm long anodised barrel tower bolt of extruded section, complete all as specified and as directed by Engineer -in-Charge. |
| 23 | S&F Aluminium alloy 100mm long anodised barrel tower bolt of extruded section, complete all as specified and as directed by Engineer -in-Charge. |
| 24 | S&F Aluminium alloy 150mm size handle extruded anodised, fabricated type, complete all as specified and as directed by Engineer -in-Charge. |
| 25 | S&F Aluminium alloy 100mm size handle extruded anodised, fabricated type, complete all as specified and as directed by Engineer -in-Charge. |
| 26 | Supply and fixed in repairs Stainless steel wire cloth 0.63mm nominal dia of wire and average width of aperture 1.40mm fixed to steel door/ Windows with flat iron and screw complete all as specified and as directed by Engineer-in-Charge. |
| 27 | Supply and fixed in repairs 4mm thick figured glass ordinary quality and glazing with rubber packing around the glass, in squares n. exc 0.5 Sqm in each pane complete all as specified and as directed by Engineer-in-charge. |
| 28 | S&F Powder coated Aluminium (minimum thickness of powder coating is 50 microns) Door / window / Ventilator/railing/ partition frames and shutters (02 Nos glazed & gauged), side hung type, without sash bars, standard aluminium grills, necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, magnet catch etc, complete with standard aluminium sections, all as specified and as directed by Engineer-in-charge.(Aluminium section shall be of make Jindal/Hindalco/ Indalco).(Note:- Weight of various Aluminium sections shall only be considered for measurement for payment. Weights of builders hardware like aluminium aldrop, tower bolts, handles of required size and type shall not be considered. Cost of rubber packing given in the item shall be deemed to be included in the rate quoted. Glass panels, aluminium wire cloth as applicable will be measured and paid separately as supplied only). |
| 29 | Supply only aluminium alloy wire mesh 0.45mm nominal dia of wire and average width of apeture 1.4mm fixed with aluminium wire staples etc.complete all as specified and as directed by Engineer-in-charge. |
| 30 | S&F in repairs Powder coated aluminium grill of design DG-104 pattern, made out of 10mm dia rod fixed with and including standard aluminium frame of 'F' section of size 23.4x15.3x1.4mm thick all as per manufacturer's instructions comlete all as specified and as directed by Engineer-in-charge. |
| 31 | Supply only 4mm thick ACP board (Aluminium composite panel) fixed to aluminium frames complete all as specified and as directed by Engineer in charge |
| 32 | M & L for painting with two coats of oil bound distemper over a coat of primer on newly plastered or untreated surfaces of walls including nesessary preparation of surfaces complete all as specificed and as per directed by Engineer-in-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jun 30, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 21, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 12 daysJul 23, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 14 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender