Tender For Special Repair To Bldg No P-03/04( Otm) Of 06 Raj Rif At Stn Pithoragarh Under Ge(Mes) Pithoragarh
Tender Value
38.61 Lakhs
Estimated cost
Bid Submission
22 Jul 2026
13 days left
EMD
77500
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Pithoragarh → Uttarakhand
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repair To Bldg No P-03/04( Otm) Of 06 Raj Rif At Stn Pithoragarh Under Ge(Mes) Pithoragarh
BOQ
| Sl. No. | Item Description |
| 1 | DESCRIPTION OF ITEMS |
| 2 | Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern as in roof coverings.Complete all as specified and directed. |
| 3 | Dismantling mild steel section work of any description not otherwise provided for complete all as specified. |
| 4 | Dismantling wall and ceiling boards, fibre or pulp, insulation etc. in insulation boards slabs, blankets any thickness incl cover fillets. |
| 5 | Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc.Laid, bedded and pointed in any mortar complete as directed and specified. |
| 6 | Demolition of concrete of any description and in any position not otherwise specifically provided for. Complete all as specified and as directed. |
| 7 | Demolition of precast concrete block walling,stone boulder masonary dressed stone work built in cement mortar complete all as specified and directed. |
| 8 | Taking down cement plaster of any description, thickness on brick, stone, concrete surfaces including racking out joints, hacking for key, scrubbing down with water, removal of rubbish and cleaning, etc complete as directed and specified. |
| 9 | Taking down Chowkats or frames with shutters (without taking off shutters from the frame) exc 1.50 sqm but n.exc 4.0 sqm each and removing from site including making good disturbed portions of wall with new or old bricks, lintel, cills etc in CM 1:4 complete all as specified and directed. |
| 10 | Taking down Chowkats or frames with shutters (without taking off shutters from the frame) n.exc 1.50 sqm each and removing from site including making good disturbed portions of wall with new or old bricks, lintel, cills etc in CM 1:4 complete all as specified and directed. |
| 11 | Dismantling of cast iron/ PVC /AC /SGSW pipes alongwith fittings and accessories upto 100 mm dia jointed in cement mortar and taking out of walls, floors or trenches, if required complete all as specified and directed. |
| 12 | Taking up or down 15 mm steel tubing and connections with fittings from walls/floor or from trenches complete all as specified and directed. |
| 13 | Taking up or down 20 mm steel tubing and connections with fittings from walls/floor or from trenches complete all as specified and directed |
| 14 | M&L PCC 1:4:8 type D 2 (40mm graded aggregate), 75 mm thick as in floor sub base complete all as specified and directed. |
| 15 | M & L for 25 mm thick PCC 1:2:4 type B-0, using 12.5 mm graded stone aggregate as in floors, to receive surface of tile complete all as specified and directed. |
| 16 | M & L for coloured ceramic joint free tiles (GVT) 7 to 8 mm thick (square/ rectangular) of size 600 x 600 mm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and incl screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:6,incl demoltion of existing flooring, complete all as specified and directed. |
| 17 | M & L for coloured ceramic joint free tiles (GVT) 7 to 8 mm thick (square/ rectangular) as in Skirting, riser etc (length of tiles not less than 600 mm) set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10 mm thick rendering in CM 1:4 incl demoltion of existing tiles, complete all as specified and directed, |
| 18 | M & L Green Marble work 16 to 18mm thick (table rubbed and polished) in floors, steps, window cills incl moulding edges and polishing etc complete laid over and incl screed bed or bedding layer of mortar, 20 mm thick, in cement mortar 1:4 with admixture of pigment to match with marble shade ,complete all as specified and directed. |
| 19 | M & L Green Marble work 16 to 18 mm thick (table rubbed and polished) in risers of steps,skirting or other vertical surfaces and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade alid over and including 10mm thick rendering in CM 1:4 complete all as specified and directed. |
| 20 | M & L for non-skid coloured ceramic joint free tiles 7 to 8 mm thick (square/ rectangular) of size not exc 0.18 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:6,incl demoltion of existing flooring, complete all as specified and directed. |
| 21 | M&L coloured Glazed ceramic tiles size not exc 0.18 sqm , 7 to 8 mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match on vertical surfaces of wall over and including a backing layer of 10 mm thick rendering on brick surface in CM 1:3. complete all as specified and as directed. |
| 22 | M & L 16 to 18 mm thick granite stone slab machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing as in kitchen platform/dado/skirting /platform counter top WHB including cutting holes for oval shape /urinal partitions, door/window cills etclaid over and including 20 mm thick cement screed bed 1:6 CM in horizontal or vertical surfaces including grinding the edges half round and polishing complete all as specified and directed by Engineer-In- Charge. |
| 23 | M&L 75mm thick PCC 1:3:6 type C-2, (20 mm graded stone aggregate)as plinth protection and finishing even and smooth without using extra cement incl making joints 12 mm wide of full depth of PCC at every 3 meters and at every change in direction and filling the same with sealing compund grade 'A' incl necessary formwork. Complete all as specified and directed. Note; The rate quoted by the tenderer are deemed to be included necessary form work for provining joint and filling the joints with sealing complound and nothing extra shall be claimed by contractor for the above provisions. |
| 24 | M&L for rendering 10 mm thick , in cement mortar 1:3 over RCC slab, mixed using water proofing compound liquid @ 200 ml per bag of cement. Complete all as specified and directed. |
| 25 | M&L cement concrete 1:5:10 type E-2 using 20mm granded brick aggregates as in sunken portion etc complete all as specified and as directed |
| 26 | M&L for cement concrete 1:2:4 type, B1 using 12.5 mm graded stone aggregates as in copings, roof padding/staging of water tank etc mixed with water proofing compound complete all as specified and as directed |
| 27 | M & L for water proofing treatment to RCC slab with APP based modified polymeric membrane as per manufacturers instructions with following course of description below:-(a) Applying a priming coat of bituminous primer @ 0.30 kg / sqm, till the surface is properly impregnated.(b) Providing APP based 5 layer polymeric membrane minimum weighing 3.6 kg / sqm and minimum 3 mm thick reinforced with polyester non-woven fabric (weight not less than 150 gms /sqm) centre core, laid on primed surface Fixed with hot molten bitumen of grade 85/25 @ 1.2 Kg / Sqm by forced applications as per manufacturers instructions with side over lap of 100 mm and end overlap of 150 mm. All overlap joints shall be sealed thoroughly by thermo fusing both the membrane layer (torching overlap by propane or butane gas torch) and sealing it with the help of hot trowel. The overlap joints shall be made as a monolithic layer. |
| 28 | M&L precast cement concrete Block Masonary with soilid blocks type C1 1:3:6 (20mm graded stone aggregate) exc 10cm in width and setting in mortar 1:6 complete all as specified and directed . |
| 29 | M&L for 15mm thick rendering in cement mortar 1:6 to on brick masonary wall surfaces or on other than fair faces of brick masonary finished even and fair without using extra cement complete all as specified and directed. |
| 30 | M&L for 15mm thick rendering on fair faces of brick/ concrete surfaces in CM 1:4 finished even and fair. Complete all as specified and directed. |
| 31 | M&L for 5 mm thick rendering in CM 1:3 on ceiling, soffits, chajja projection etc complete all as specified and directed. |
| 32 | M&L for extra over rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirtings, drip moulds and similar work not exc 15 cm in width or girth; including cutting to edges, all mitres and stopped ends etc.complete all as specified and as directed |
| 33 | M & L 595 mm x 595 mm false ceiling system , using hot dipped galvanised steel section exposed surface with precoated capping, GI tee (Galvanised @120 grms, both side inclusive and black painted groove on all T webs) and cross tee of size 24 x 32 mm & 24 x 27 mm having 0.27 mm gauge at every 600 mm c/c interval and wall angle of size 19 x 19 mm having 0.35 mm gauge fixed to the wall. The above grid is to be suspended at every 1200 mm c/c in both direction using 2mm thick pre-straightened GI wire laying designer tile ivory painted (high pressure steam cured) of 4 mm thickness (as per IS 14862) of size 595 x 595 mm , back of the tile duly sanded and finished with a coat of protective paint over the formed grid etc including taking down of old unsv ceiling with frames complete all as specified and directed. |
| 34 | S&F 1.25 mm thick pressed steel frame of size 125 X 60 mm for door with one or more rebate includings necessary fixing lugs, hinges, locks strike plate etc complete all as specified and as directed |
| 35 | M & L PCC 1:3:6 Type C 0 usind 12.5 mm graded stone aggregate for backing of door chawkhats complata all as specified and directed by Engr-in Charge |
| 36 | S&F factory made flush shutters ,30 mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides.Complete all as specified and directed. |
| 37 | S&F IInd class hard wood, 30mm thick skeleton shutters open rebated & prepared to receive, glass, gauge etc. (without sash bars), edge of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc, size of members of shutters as specified in SSR Part I, Section 8, clause 8.24(a); supplied and fitted to chowkahts. Complete all as specified and directed. |
| 38 | Preparation of new wooden surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer. Complete all as specified and directed. |
| 39 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing |
| 40 | S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. |
| 41 | S&F powder coated anodised aluminium window (three track) and ventilator shutters (powder coating of any colour, thickness or powder coating not less than 50 micron) side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1no.) complete all as specified. |
| 42 | Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) windows & ventilators frames, partitions etc including providing and fixing hinges/ pivots/roller incl fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per the directions of Engineer-in-charge |
| 43 | S&F for mild steel window grills , framed work as in window guard bars, grills or forged into spikes, framed balusters, walkway railing, stair case railings, monkey cages, and similar work including welding, FE-290 grade E-165 complete all as specfied and directed. |
| 44 | S&F sheet glass ordinary quality 4mm thick and glazing with oil putty or fixed with bead/ glazing pins in squares n.exc. 0.5 sqm each pane complete all as specified and directed. |
| 45 | S&F 4 mm thick Figured glass, pin head type and glazing with oil putty or fixed with bead/ glazing pins in squares n.exc. 0.5 sqm in each pane complete all as specified and directed. |
| 46 | S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainles steel wire stapel etc complete all as secified and as directed |
| 47 | S&F Aluminium annodised barrel tower bolt of extruded section and fixed 200 mm size with bright bolt complete all as specified and directed. |
| 48 | S&F 300 mm long aluminium alloy annodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet castor extruded sections and fixing bolts and slidding bolts of extruded section or cast aluminium alloy and fixed all as spd and directed |
| 49 | S&F extruded Aluminium alloy handle fabricated annodised 150 mm size, complete all as specified and as directed . |
| 50 | S&F MS 300 mm ordinery rat rail rod pattern spring including roller and roller plate complete all as specified and as directed . |
| 51 | S&F 150mm long floor door stopper of aluminum alloy body and tongue , anodized with hard drawn steel spring complete all as specified and directed |
| 52 | S&F in repairs stainless steel (Grade SS 202) decorative curtain rod of 25 mm bore.complete all as specified and as directed |
| 53 | S & F in repair stainless steel glossy finish hat peg set of five tier with necessary fitting complete all as specified and directed. |
| 54 | S&F 1000 litre capacity rotational moulded polythylene water storage tanks (cylindrical vertical with closed top ) hoisted and fixed in position including dismantling of existing water tanks complete all as specified and directed. |
| 55 | S&F in repair 20mm ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed etc complete all as specified and as directed |
| 56 | S&F in repair Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe 20 mm bore complete all as specified and as directed |
| 57 | M & L for cutting chases, pinning in brick/PCC blocks wall in making good to facings where required and pointing in cement mortar 1:3 and cutting chases for concealed water tubing etc and making good complete all as specified and as directed |
| 58 | Supplying and laying of CPVC pipes (outer dia 20 mm) SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. |
| 59 | S&F CPVC brass elbow for CPVC pipe size 20 mm |
| 60 | S&F Male Brass Threaded Adaptor for CPVC pipe size 20 mm (MTA/ MBTA) |
| 61 | Female Brass Threaded Adaptor for CPVC pipe size 20 mm (FTA/ FBTA) |
| 62 | S&F tubes medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors 20 mm dia bore pipe (including in short length) complete all as specified and as directed |
| 63 | S&F tubes medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors 25 mm dia bore pipe (including in short length) incl dismantling, complete all as specified and as directed |
| 64 | S&F tubes medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors 32 mm dia bore pipe (including in short length) incl dismantling, complete all as specified and as directed |
| 65 | Refixing old serviceable 20 mm GI tubing and connection in new or old position (concealed in Wall, ceiling floor etc.) including necessary fittings & fixtures etc. incl taking down complete all as specified and directed |
| 66 | S&F in repairs Oval type Wash Hand Basin (Counter Top) superior quality 550 x 400 mm size fitted over granite slab incl waste pipe coupling 150mm long complete all as specified and directed. |
| 67 | S & F in repair fancy type 125mm size square brass CP shower rose with or without swivel joints complete all as specified and as directed. |
| 68 | S&F in repair, Brass CP wash basin mixer (Long nose Elbow Operated)15mm bore dia for mixing Hot or Cold water screwed down for iron pipe and fixed all as specified and as directed. |
| 69 | S & F Brass CP wall mixer 15 mm bore (wall mounted type three way) for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and as directed. |
| 70 | S&F in repair bib tap long body fancy type cast copper alloy chromium plated with crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule or fixed for 15 mm dia bore pipe complete all as specified and as directed. |
| 71 | S&F in repair stop valves/angle valves fancy type chromium plated brass cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions fixed for 15 mm dia bore pipe complete all as specified and as directed |
| 72 | S&F in repairs Bevelled edge mirror 5.5 mm thick (frame less of selected quality) fixed with appropriate number of SS studs etc complete all as specified and as directed |
| 73 | S&F in repair tubular towel rail 20mm dia type brass chrormium plated 600mm long between flanges complete all as specified and as directed |
| 74 | S&F in repair PVC connection of 45 cm length including brass nuts complete all as specified and as directed |
| 75 | S&F in repairs fancy type brass chromium plated soap dish of 160x160x90 mm complete all as specified and directed. |
| 76 | S&F in repairs fancy type corner shelf assembly 300mm radius three tiers fixed with fancy type screws complete all as specified and directed. |
| 77 | S&F in repairs vitreous china squatting pan orissa pattern long pan size 580 mm x440mm white with spun pipe ‘P’ or ‘S’ trap, front or back inlet and foot rests excluding flushing cistern & flush pipe but incl. cement concrete bedding fixed complete all as specified and as directed |
| 78 | S & F (in repair) vitreous china wash down water closet pan (pedestal pattern), white, including plastic seat cover and flushing pipe complete all as specified & directed. |
| 79 | S&F in repair PVC low level flushing cistern 10 litres, valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, flushing pipe complete all as specified and directed. |
| 80 | S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect. Complete all as specified and directed. |
| 81 | S&F in repair Toilet paper holder with flat recessed type stainless steel Complete all as specified and directed |
| 82 | S&F 75mm bore PVC(SWR) pipes single socketed , in any length with rubber ring joints, laid in trenches or in floors and fixed to wall with PVC holding clamps complete all as specified and directed. |
| 83 | S&F 110mm bore PVC(SWR) pipes single socketed , in any length with rubber ring joints, laid in trenches or in floors and vertical surfaces complete all as specified and directed. |
| 84 | S&F 75mm bore dia PVC floor trap (SWR) plain with grating including jointing with solvent cement to waste pipe complete all as specified and directed. |
| 85 | S&F 75mm bore PVC(SWR) Reducer, TEE, Y, etc complete all as specified and directed. |
| 86 | S&F 110mm bore PVC(SWR) bends any radius, complete all as specified and directed. |
| 87 | S&F 110mm bore PVC(SWR) Acess door bends any radius, complete all as specified and directed. |
| 88 | S&F 110mm bore PVC(SWR) Reducer, TEE, Y, etc complete all as specified and directed. |
| 89 | S&F 75mm bore PVC(SWR) vent cowl complete all as specified and directed. |
| 90 | S&F MS joist channel (Fe 410-W Gde E-250 Quality A), angle or Tee section MS tubes, flats square bars etc fixed indepently or framed or without connecting plates ,trusses etc any type framing including purlins and rafters etc confirming to Grade Fe 410-0 or Fe-310-0 complete all as specified and directed by Engr-in-Charge |
| 91 | Erection and fixing only Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates |
| 92 | S & F pre-painted galvalume aluminium zinc coating GI based corrugated steel 0.50 mm thick of any colour as directed by GE having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge |
| 93 | S & F pre-painted galvalume aluminium zinc coating GI based plain steel 0.50 mm thick for ridge cover of any colour as directed by GE having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge |
| 94 | S&F in repairs 20 mm thick boarding of 2nd class hardwood as in roof facia ,Planed one side, with butt joints and fixed with nails supplied and fixed complete all as specified and as directed |
| 95 | S&F mild steel angles, tees, flats, C section, MS square bars, MS Tubes etc as in steel gates, steel posts and struts in fencing, grills,railling etc including embedding in concrete and screwing etc. including cut to shape as directed, drilling holes, notching for wire etc including all necessary drilling, bolting, welding or riveting and similar work conforming to FE-290 Gde E-165 complete all as specified and directed by Engineer-in-Charge. |
| 96 | M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and as directed |
| 97 | M&L for applying one coat of synthetic enamel paint including preparation of old steel surfaces of any description over 10cm width or girth all as specified. |
| 98 | M&L for applying two coat exterior emulsion paint (weather coat of Berger or equivelent ) on newly plastered wall over a coat of primer over one coats of wall care putty of 1-1.5mm thickness prepared and sanded .complete all as specified and directed.. |
| 99 | M&L for complete removal of existing treatment and applying two coat exterior emulsion paint (weather coat of Berger or equivelent ) on old plastered wall after preparing old surface over one coats of wall care putty of 1-1.5mm thickness prepared and sanded ,complete all as specified and directed.. |
| 100 | M&L for applying two coat Oil bound distemper (acrylic emulsion ) on newly plastered wall after preparing the surface over one coats of wall care putty of 1-1.5mm thickness prepared and sanded , complete all as specified and directed.. . |
| 101 | M&L for complete removal of existing treatment and applying two coat Oil bound distemper (acrylic emulsion ) on old plastered wall after preparing old surface over one coat of wall care putty of 1-1.5mm thickness prepared and sanded , complete all as specified and directed.. |
| 102 | M&L for applying two coat Oil bound distemper (acrylic emulsion ) on newly plastered ceiling surfaces after preparing the surface over one coats of wall care putty of 1-1.5mm thickness prepared and sanded .complete all as specified and directed.. |
| 103 | M&L for complete removal of existing treatment and applying two coat Oil bound distemper (acrylic emulsion ) on old plastered ceiling surface after preparing old surface over one coat of wall care putty of 1-1.5mm thickness prepared and sanded ,complete all as specified and directed.. |
| 104 | M & L for walling of random rubble, uncoursed well bounded, bedded and solidly hearted, built in Cement Mortar 1:6 and complete all as specified and directed. |
| 105 | M & L for walling (Except stone) of random rubble, uncoursed well bonded, bedded and solidly hearted, built in Cement Mortar 1:6 and complete all as specified and directed. |
| 106 | Hand packing (any thickness) at back of walls with broken stone or boulders and raising (or lowering) to the required level complete all as specified and directed. |
| 107 | M & L for providing cement concrete type B1 ( 1:2:4) using 20 mm graded stone aggregate, as in coping , bed blocks including necessary form work and incl demolition complete all as specified and directed |
| 108 | M & L for providing precast cement concrete bonders (for stone walling) type B1 (1:2:4) using 20 mm graded stone aggregate, set in cm 1:6 complete all as specified and directed. |
| 109 | M&L for raised pointing to random polygonal rubble, uncoursed or brought upto courses in Cement mortar (1:4) complete all as specified and directed. |
| 110 | Demolition of cement concrete (reinforcement cut as required to facilitate demolition) of any description & in any position not specifically provided for complete all as specified and as directed. |
| 111 | M&L for reinforced cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) (nominal mix) as in slabs supported on wall, landing, balconies, canopies, deck slabs and in shelves and like in repair to Chajjas, Claddings, soffits etc including bonding agent, complete all as specified and directed. |
| 112 | M&L for form work to chullah hoods, chajjas, troughs and similar items including edges for rough finished surfaces of concrete flat, complete all as specified and directed. |
| 113 | M & L for form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide for rough finished surfaces of concrete complete all as specified and directed. |
| 114 | M&L for TMT Bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete incl welding etc (if reqd) all as specified and directed. |
| 115 | S&F Heavy duty outdoor tiles of size not exceeding 0.36 sqm, 10-12 mm thick set and jointed in neat cement slurry over and incl 20 mm thick cement screed bed in CM 1:4 complete all as specified and as directed. |
| 116 | Supply only liquid water proofing compound complete all as specified and directed. |
| 117 | Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting, bell, bell push etc and removing material from site as directed by Engr-in-charge. |
| 118 | Point wiring of one light point/fan/bell point controlled by one switch with 1.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable FRLS with proper color coding and 1.5 sqmm PVC insulated unsheathed copper conductor single core multistranded cable (green color) as earth lead in and including concealed non metalic rigid PVC conduit medium grade size min 20 mm dia or higher with all fittings (ISI Marked) controlled by one switch including GI modular sunken box of thickness not less then 1.2 mm with cover frame(Inner/Outer) for mounting modular type switches, socket and regulators , including cutting chases to wall making good the disturbed surfaces to match with the existing specification complete all as specified. |
| 119 | Point wiring of one light point controlled by Two way switches with 1.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable FRLS with proper color coding and 1.5 sqmm PVC insulated unsheathed copper conductor single core multistranded cable (green color) as earth lead in and including concealed non metalic rigid PVC conduit medium grade size min 20 mm dia or higher with all fittings (ISI Marked) controlled by one switch including GI modular sunken box of thickness not less then 1.2 mm with cover frame(Inner/Outer) for mounting modular type switches, socket and regulators , including cutting chases to wall making good the disturbed surfaces to match with the existing specification complete all as specified. |
| 120 | Point wiring for one 3 pin 15A socket outlet independent with 2.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable FRLS with proper color coding and 2.5 sqmm PVC insulated unsheathed copper conductor single core cable (green color) as earth lead in incl PVC conduit medium grade of 20 mm dia or higher with all fitting (ISI marked) .all as required at site or directed. |
| 121 | Point wiring in of one Plug top socket outlet for geyser independent with 4.00 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable FRLS with proper color coding and 4.00 sqmm PVC insulated unsheathed copper conductor single core cable (green color) as earth lead in incl PVC conduit medium grade of 20 mm dia or higher with all fitting (ISI marked) .all as required at site or directed. |
| 122 | Point wiring in of one 5A socket outlet on the same board with 1.5 sqmm PVC insulated unsheathed copper conductor single core multi strand flexible cable FRLS with proper color coding and 1.5 sqmm PVC insulated unsheathed copper conductor single core cable (green color) as earth lead in and incl PVC conduit medium grade of 20 mm dia or higher with all fitting (ISI marked) .all as required at site or directed. |
| 123 | S&F in repairs for submain wiring with two single core PVC insulated flexible copper conductor multistranded cable (FRLS) of size 6 Sqmm with proper color coding and one single core PVC insulated flexible copper conductor multistranded cable green colour of size 6 Sqmm as earth lead in & including concealed PVC conduit medium grade 25 mm dia or higher cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specification all as required at site or directed. |
| 124 | S&F of switch modular type single pole one way 1 module 6 amps 240 volts. |
| 125 | S&F of switch modular type single pole two way 1 module 6 amps 240 volts. |
| 126 | S&F of switch modular type one way 1 module 16 amps 230 Volts. |
| 127 | S&F of socket 6 amps modular type 2/3 pin combined 2 module , 230 volts. |
| 128 | S&F of socket modular type , 2/3 pin, 6 and 16 amps combined 2 module, 230 volts. |
| 129 | S&F of ceiling rose surface bakelite 3 terminals. |
| 130 | S&F of Modular type Electronic fan regulator stepped type,two module with five step 240 volts,100Watt suitable for 1200/1400 mm sweep AC ceiling fan complete, all as directed by Engineer in charge. |
| 131 | Taking down Celing Fan any Sweep from the exsisting site and keep safe and under custody and complete cleaning, Oiling ,Greasing ,including replacement of capacitor , bearing and nut washet bolt and clamps of fan and Refixing fan as existing location and connection to celing rose with copper wire twin core complete all as specified and directed. |
| 132 | S&F of Tube light fitting integrated type suitable for LED 20 W(4 feet) efficacy min 100 lumens/watt, indoor decorative LED batten complete with Aluminium housing and all accessories pre wired and making connection with cord flexible copper cable of suitable size from ceiling rose to PVC connection to light fitting complete all as specified and directed. |
| 133 | S&F of Tube light fitting integrated type suitable for LED 10 W (2 feet) efficacy min 100 lumens/watt, indoor decorative LED batten complete with Aluminium housing with all accessories pre wired and making connection with cord flexible copper cable of suitable size from ceiling rose to PVC connection to light fitting complete all as specified and directed. |
| 134 | S&F of LED bulk head fitting with opal diffuser min 10 Watt, 6500 K, IP-65, with Aluminium housing of efficient heat dissipation and integrated electronic driver with surge protection complete connecting electrically all as directed. |
| 135 | Supply and fixing LED street light fitting 60 Watt 230 V AC, in multiple optics,Outdoor type with high pressure die cast aluminum housing, IP-65, with 4 KV inbuild surge protection driver and heat resistant complete with driver, fixing the same by GI pipe medium grade minimum 25 mm dia bore pipe with two nos FI clamps of 40X4 mm duly painted and suitable size of nut and bolts etc and making poper electric connection with three core flexible copper wire complete all as specified and directed. |
| 136 | S&F in repairs of modular type 3/4 module power unit with 16 Amp plugtop Box with sheet steel enclosure DBOXx MCB Combo plug and socket complete with one SP MCB 20 Amps, 240 Volts. Protection to human shock due to direct or indirect contact as well as provides protection from overload and short circuit faults, all as specifed and direced. |
| 137 | S&F in repairs of TPN DB, 4 Way, as per IS-8523, IP-43 protection, min 1.6 mm thick CRCA Sheet and fixed to wall and suitable for universal mounting with 200A copper bus bar with neutral bar, standerd DIN Rail, earth bar and cable ties for cable management, top and bottom removable gland plate suitable for MCB TPN as incomer and MCB TPN/MCBs as outgoing, with and including provision for MCCB/MCBs & making necessary electrical connection for Incoming & outgoing cables, with copper lugs, crimped with crimping tool,all as specifed and direced. |
| 138 | S&F of MCB TPN- 100 Amp 415 Volts, MCB C- Curve ultimate breaking capacity (Icu)-10 KA., all as specifed and direced. |
| 139 | S&F in repairs of sheet metal enclosure MCB distribution board 12 ways 240 V, double door with IP-43 IK-09 protection fabricated from min 1.6 mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and in cluding 200 Amp copper bus bar, neutral bar, standard DIN Rail, Earth bar and cable ties for cable management top and bottam removable gland plate with Knockout and suitable for SPN/DP-MCB as Incommer and SP MCBs as Outgoing. Making good distributed wall surfaces to match with existing specification , all specified and directed. |
| 140 | S&F in repairs of sheet metal enclosure MCB distribution board 8 ways 240 V, double door with IP-43 IK-09 protection fabricated from min 1.6 mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and in cluding 200 Amp copper bus bar, neutral bar, standard DIN Rail, Earth bar and cable ties for cable management top and bottam removable gland plate with Knockout and suitable for SPN/DP-MCB as Incommer and SP MCBs as Outgoing. Making good distributed wall surfaces to match with existing specification . All specified and directed. |
| 141 | S&F in repairs of MCB SP of 6 to 32 Amp rating 240,10 KA C- curve with connection testing and commisioning. |
| 142 | S&F in repairs of MCB SPN of 40-63 Amp rating 240,10 KA C- curve with connection testing and commisioning. |
| 143 | M&L for Earthing complete with galvanised cast iron earth plate electrode of size 600x600x6mm thick as earth electrode with top edge of the earth plate not less than 1.5mtr below ground level using GI wire 4mm dia as earth continuity conductor connected to earth plate by means of GI thimbles nuts bolts washers all as directed including providing earth wire protection pipe GI light grade15mm dia from earth plate to main switch board/panel, watering pipe 20mm dia with wire mesh and funnel at top, earth pit and RCC pit cover in PCC 1:3:6 adequate quantity of charcoal dust and salt all around the erth plate, earth work in any type of soil remaing surplus excavated material all as required at site and specified in SSR part I or directed by Engineer-in-charge and testing on completion. |
| 144 | Supply and fixing LED flood light 100 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant, energy saving, Environment friendly, life long, die cast aluminium complete with driver and lamp and fixing arrangement suitable size of nut and bolts etc and making poper electric connection with three core flexible copper wire complete all as specified and directed. |
| 145 | Supply install and tesing water heater storage type (Geyser five star rating) single phase 230 V, 50 Hz, 5 star energy saving high density PUF insulation tank made of heavy duty mangesium anode rod with steel core to protect enamelled tank from rust & corrosion, vertical installation type 25 Ltr Cap 2000 Watt rated power, incoloy 800 glass coated heating element, inner tank coating of feroglas powder, tank made of ultra thick super cold rolled steel plates, rated pressure 0.8 MPa, IPX4 protection consist of safety valves, thermal cut off, thermostat including connecting up and fixing arrangement on wall including providing hole fastners-04 Nos hot and cold water metallic flexible pipes 15 mm bore of adequate length as provided by OEM or required at site - 02 Nos non return valve 01 No and including necessary plumbing work, complete with intergated shock safe PRCD plug with all protection features as per OEM design and standard all as specified and directed. |
| 146 | Supply and fix Exhaust fan , steel body AC single phase 230 V of size 300 mm (12'') sweep single phase 230 V 50 Hz AC 1400 RPM energy saving, heavy duty motor copper wounded with die cast aluminium rotor mounted on two ball bearing complete with louvrs shutter including making hole of suitable size and making good disturbed surface (including making hole and plasterng, nacessary brickwork and distemparing to match with existing) connecting with 3 core copper cable to ceiling rose. All as specified and directed .Note: The rate quoted by the tendere are deemed to be included for providing opening holes of suitable size on wall for hoisting and making good the disturbed surfaces of wall as per existing and nothing extra shall caimed by the ocntractor on this account. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jun 30, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 22, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 13 daysJul 29, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 20 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender