Tender For Tree Plantation Including Fencing, Tube Well, Solar System And Drip Irrigation System At Jawaja Block Distict Beawar.
Tender Value
58.23 Lakhs
Estimated cost
Bid Submission
09 Jul 2026
8 days left
EMD
1.16 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ajmer → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Tree Plantation Including Fencing, Tube Well, Solar System And Drip Irrigation System At Jawaja Block Distict Beawar.
BOQ
| Sl. No. | Item Description |
| 1 | जंगल की साफ सफाई साधारण वनस्पति तथा झाड़ियो काटने सहित |
| 2 | 45x45x45 सेमी माप के गड्डे करना । dadj@eqje feêh |
| 3 | 45x45x45 सेमी माप के गड्डे करना । कठोर मिट्टी |
| 4 | थांवला बनाना । कम से कम 50 सेमी अर्द्ध व्यास का । पथरीली जमीन |
| 5 | थांवला बनाना । कम से कम 50 सेमी अर्द्ध व्यास का । सामान्य जमीन |
| 6 | पौधा रोपण करना । पथरीली जमीन |
| 7 | पौधा रोपण करना । सामान्य जमीन |
| 8 | पौधों की निड़ाई गुडाई करना। 15 सेमी गहराई तक तथा 45 सेमी अर्द्ध व्यास तक । |
| 9 | Supplying of insecticide liquid including transportation |
| 10 | पौधारोपण हेतु पौधा की कीमत एवं परिवहन सहित आपूर्ति 5 फीट से अधिक ऊंचाई के हो |
| 11 | Ward and Watch of Plantation Work (Chokidar) |
| 12 | 120cm. high fencing with angle iron posts 50x50x6mm. placed at every 3 Mtr. apart 30cm. in ground embedded in cement concrete 1:3:6 (30x30x45cm) corner & every tenth posts to be strutted with 50x50x6mm angle iron provided with four horizontal lines and two diagonals of black barbed wire between two posts fitted and fixed with G.I. staple including earth work in excavation etc. complete. |
| 13 | Add for each wire line over basic item (2 wires) |
| 14 | Add for additional or less higher per 10 Cm. over basic item( 5 % of Basic rate)for 60 cm height= 5*6= 30% i.e. 470*0.30=141 |
| 15 | Construction of Tube Well up to 100 mtr. depth in all type of rocks by DTH system & over burden to accommodate casing pipe of following sizes in all types of soils & over burden including lowering of casing pipes, (if required) excluding cost of casing pipes, as per IS:2800 Part 1: 1991 and IS:2800 Part II: 1979 (both amended up to date) and technical specifications. The work would be completed after obtaining sand free water. The tube well should have a through out bore as per nominal dia of casing pipeNominal bore 200 mm dia |
| 16 | Supply of ERW M.S. black casing pipe ISI marked (IS: 4270/2001) or amended up to date of following sizes200 mm dia NB (Thickness of pipe 5.4mm & mass of tube 28.46 Kg/m) |
| 17 | Supply & Fixing tube well cover of MS sheet 8mm thick at top & 5mm thick 100mm wide shroud around the edge so as to form a cap on the top end of casing pipe with GI Nipple 45cm long & two GI flanges at both ends in 80mm sizes passing through a hole in the centre of MS sheet. A 25 mm socket with end plug shall also be welded over top plate. A GI nipple having outside thread of size 1/2\\" (for installation pressure gauge) shall be provided & welded with 80mm GI nipple near top plate nipple shall be provided with end plug.200 mm dia |
| 18 | Providing, installation, testing and commissioning of AC submersible pump sets with inbuilt or individual solar pump controller with Maximum power point tracking (MPPT) for optimally use the solar panel and maximize water discharge to deliver maximum water during the day including PVC flat submersible cable from controller to motor pumps..Solar pump shall be of Stainless steel construction and performance shall be as per scope of work and minimum lift of water shall be as per defined in scope .Pump controller shall have Adequate protection against dry operation ofmotor pump set, and against hails and storms. Full protection against open circuit, accidental short circuit and reverse polarity should be provided. A good reliable on/off switch be provided. The cable shall be ISI marked three core PVC flat submersible cable as per IS 694:1990 or amended up to date (standard insulation) and conductor as per class 5 of IS 8130:1980 or amended up to date.The duty condition of pump set shall be as per scope of work and entirework shall be executed as per technical specification and direction ofEngineer in charge.. 3.7 KW (5.0 HP) |
| 19 | Supply, installation, testing and commissioning of MNRE approved off Grid Solar Panels for running of motor pumps with 25 years of Linear Generation warranty, Work includes designing of solar panel area and MS frame and foundation on ground/roof of Pump house or CWR, showing arrangement of panel in available space, installation of PV module on MS frame as per approved design and drawings. Mounting structure shall be suitably design to withstand wind velocity up to 150km/hr. The work shall be executed as per detailed technical specifications, approved drawing and direction of Engineer in Charge.Note: There shall be 5 year service warranty for solar panel and mounting structure and suitable provision shall be included in tender document. |
| 20 | Providing, lowering, laying and jointing in trenches, standard lengths HDPE ISI marked Pipes as per IS-4984: 1995 (amended up to date) with necessary jointing material like mechanical connectors, i.e. thread/ insert joint/ quick release coupler joint/ compression fitting joint or flanged joint and specials jointing pipe by electro fusion welding method, including all taxes , transportation and freight charges, inspection charges, loading/ unloading charges, stacking of pipes, including cost of labour and material, specials (Tee, bend etc.), satisfactory hydraulic testing, disinfection, commissioning etc. complete as per technical specifications and direction of Engineer-in-charge of following class and diameter. (excluding earth work) .Note : Providing and fixing of all requisite specials as per drawing,design and layout are inclusive in RM measurement of the item andshall not be paid separately.Supply may be in coil or straight length in 6 M/12 M.HDPE PE-80 PN-61.4.1.1 63 mm dia Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jun 30, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 09, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 8 daysJul 10, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 9 days