Tender For Special Repair To Mes Installation Shed And Adjacent In Afcme Complex At Camero Complex, Provn Of Partition Of Cabin Located At Foyer Of Recording Wing And Assocaited Works Services At Afro Building, Addn/Altn/Improvement To Certain Camero
Tender Value
49.22 Lakhs
Estimated cost
Bid Submission
27 Jul 2026
5 days left
EMD
98440
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
New Delhi → Delhi
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Mes Installation Shed And Adjacent In Afcme Complex At Camero Complex, Provn Of Partition Of Cabin Located At Foyer Of Recording Wing And Assocaited Works Services At Afro Building, Addn/Altn/Improvement To Certain Camero L/In Billets To Reduce The Leakage/Seepage And Provison Of Barrack Store For L/In Billets At Camero Complex.
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 20-Jul-2026 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 27-Jul-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | Taking down Chowkats or frames with shutters (without taking off shutters from the frame) area n exc 1.5 sqm each and inclu removing from site complete all as specified and directed. |
| 2 | Taking down Chowkats or frames with shutters (without taking off shutters from the frame) area exc 1.5 sqm and not n.exc 4.0 sqm each and incl removing from site complete all as specified and directed. |
| 3 | S&F for windows/ventilators fabricated from 0.60mm thick roll formed section made of galvanised steel powder coated (Base steel as per IS-513 \\"D\\" quality), galvanised as per IS- 277 with zinc of 120 gms/ Sqm). Window/ ventilator having frame suitable for dual shutter i.e. inner and outer shutter with grill, glazed and wiremesh and all fittings fixtures accessories including 6x12mm flat iron with 10mm MS square bar grills etc complete all as specified and shown in drg No CEAF/STD-191/2014 Sheet No 1/2 and 2/2 dated 11-12-2014 (4000 series) Note:- (i) Glazed shutter with 4mm thick glass, mesh shutter with 32 gauge stainless steel mesh and MS grill is deemed to be inclusive in the rate quoted for unit (ii) Glass, Stainless steel mesh will be fixed to window by authorised rep of manufacturer of window only. rate including making good the surface complete all as specified and directed. |
| 4 | S&F for size 105mmx60mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, hold fast, lock strike plate, and including making good with CM 1:4 and hold fast etc complete all as specified and directed. |
| 5 | S&F for size 125mmx60mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, hold fast, lock strike plate, and including making good with CM 1:4 and hold fast etc complete all as specified and directed. |
| 6 | M&L for PCC 1:3:6 type C-O (using 12.5 mm graded crushed stone aggregate) as in back filling, coping, benching on corner of joints etc complete all as specified and directed. |
| 7 | S&F for 35mm factory made plain framed, Flush shutters, solid core construction, with block board core and plywood face panels, commercial particle board with type on both faces complete all as specified and directed. |
| 8 | S&F for 35mm thick 2nd class hardwood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed. |
| 9 | M&L for Preparation of new wooden surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 10 | S&F for Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed. |
| 11 | S&F for 125mm long butt hinges medium weight, mild steel, and fixed complete all as specified and directed. |
| 12 | S&F for 150mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed. |
| 13 | S&F for 150mm long aluminium anodised, barrel tower bolts of ex-truded section and fixed complete all as specified and directed. |
| 14 | S&F for 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. |
| 15 | S&F for Steel rolling shutters, thickness of laths in1.0mm with out ball bearing, as scified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type and also including taking down existing old shutter with frame/chowkat complete all as specified and directed. |
| 16 | Taking down cement or cement lime plaster on brick walls incl racking out joints hacking for key scrubbing down with water etc complete all as specified and as directed. |
| 17 | M&L for rendering plaster 15mm thick in CM 1:4 on surface other than fair face of brick work or concrete surfaces finished even and smooth with out using extra cement upto four storey complete all as specified and directed. |
| 18 | M&L for rendering plaster 10mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement up to four storey height bldg complete all as specified and directed. |
| 19 | M&L for rendering plaster 5mm thick in CM 1:3 on ceiling surfaces finished even and smooth without using extra cement complete all as specified and directed. |
| 20 | M&L for complete removal of existing treatment on external & internal wall surfaces (old plastered surfaces) complete all as specified and directed. |
| 21 | M&L for preparation of new surfaces of walls, and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. upto four story bldgs complete all as specified and as directed. |
| 22 | M&L for preparation of new surfaces of walls and ceiling, and applying two coats of distemper oil emulsion over a coat of alkali resistant primer complete all as specified and directed. |
| 23 | Demolition and complete removal of existing roof treatment with mud phuska including bedding layer in cement mortar/plastering/leeping (whether full thickness removed or only a part thereof) complete all as specified and directed. |
| 24 | M&L for cement concrete type B0 1:2:4( using 12.5mm graded stone aggregate) as in roof kerbs or mud stops, padding, rounded or chamfered on edges without using extra cement complete all as specified and directed. |
| 25 | M&L for screed bed 10 mm thick in cement mortar 1:4 on fair faces roof surfaces with integral water proofing compound as per manufacturers instructions complete all as specified and directed. |
| 26 | M&L for preparation of plastered/concrete surfaces of roof and applying the under mentioned course of roof treatement complete all as specified and directed-(a) Surface shall be throughly wire brushed, cleaned, washed, dried up properly and apply evenly a bituminuous primer coat conforming to IS @0.4 ltr /Sqm over concrete/ plastered roof surface.(b) Applying evenly a tack coat of bitumen 85/25 grade @1.20 kg/ sqm.(c) Laying of 3mm thick APP membrane sheet (min weight 3 Kg/Sqm) consisting of a core of 160 gms/Sqm polyster non woven fabric mat (Wt not less than 150 gm/sqm) protected on both sides with a high quality polymeric asphaltic mix again protected with thermo fusible HMHDPE FILM on dried primed surface by torch application method. APP membrane will normally be laid in length at right angle to the direction of slope. The over lap shall be minimum 100mm on longitudinal direction and 150mm on the transverse direction including cuttings, grooves etc.(d) Membrane bonded completely to the substrate & the over laps are then scaled/fused by flame. Note:- This treatement shall be done by the approved authorized applicators and guarantee of treatement shall be minimum 10 years complete all as specified and directed |
| 27 | M&L for 2 coat of water proofing aluminium paint finish incl preparation of newly or previously untreated surfaces of any description, over 10cm width or girth, not otherwise described complete all as specified and directed. |
| 28 | Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness, complete all as specified and directed. |
| 29 | M&L for 25 mm thick PCC 1:2:4, type B-0 (using 12.50 mm graded crushed stone aggregates) as in floor surfaces, complete all as specified and directed. |
| 30 | M&L for 50 mm thick PCC 1:3:6 type C2 (using 40 mm graded stone aggregate) as in Plinth Protection/hardstanding including making joints & filling with sand bitumen mastic as per complete all as specified and directed. |
| 31 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed. |
| 32 | M&L for Glazed ceramic coloured tiles in vertical surface 450mmX 350mmX 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with and including backing/rendering 10 mm thick in cm 1:4 complete all as specified and directed. |
| 33 | Demolition to stone slab and kota/granite laid bedded and pointed in any mortar of any description or thickness in floors/pavings/cladding etc and removing the debries outside the MOD land complete all as specified and directed. |
| 34 | M&L for Pre polished Machine cut kota stone flooring 20-22mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab, and including 15 mm Screed bed or bedding layer of CM 1:4 complete all as specified and directed. |
| 35 | M&L for Pre polished Machine cut Kota stone slab 20-22mm thick in riser of steps, skirting, dado and pillar laid over cement screed/backing and jointed with grey cement slurry mixed with pigment to match the shade of the slab and including Rendering/backing 10mm thick in CM 1:4 on fair faces of brick work or concrete surfaces on wall, complete all as specified and directed. |
| 36 | S&F for PVC (SWR) pipes 110mm single socketed, in any length with solvent cement joints fixed to walls/laid in floors incl stack clamps of stainless steel with bolts & nuts etc and also including taking down old rain water pipes with fittings, complete all as specified and directed. |
| 37 | S&F factory made SFRC manhole / drain cover (Grade M-25) heavy duty cover slab in rectangular shape of size as required, 80 mm thick incl MS sheet 2 mm thick and 80 mm wide all around the cover inclu demolition of old manhole cover slab complete all as spefcified and directed. |
| 38 | Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed. |
| 39 | S&F for framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders;Chajjas, framed balusters; walk ways; railings; cooler stand, stair, framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 40 | S&F for Rolled Mild Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161- 1979 grade St.-240. complete all as specified and directed. |
| 41 | M&L for Preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 42 | Dismantling plain or corrugated steel sheeting any gauge, thickness, including Nainital or similar pattern roof coverings. complete all as specified and directed. |
| 43 | M&L for Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed. |
| 44 | M&L for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridge/roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed. |
| 45 | M&L for Chequered cement concrete tiles (Size 30cm x 30cm) x 25mm thick, machine pressed; set jointed and pointed in neat cement slurry in floors, with grey cement and color pigment and cut and polished laid over and including 15 mm Screed bed or bedding layer of CM 1:6, complete all as specified and directed |
| 46 | Removal of excavated/bldg material for a distance exc 5KM but n.exc 10KM and depositing outside the defence premises on desecration of Contractor as directed. |
| 47 | S&F aluminium frame powder coated any colour (minimum thickness of powder coating 50 micron) for doors, windows, partician, ventilators with one or more rebates including joining cleat for fixing etc. including taking down each chowkhats or frames with shutters (without taking off shutters from the frames) complete all as specified and directed. |
| 48 | S & F aluminium extruded section door closer hydraulically operated designation No-03, universal type, suitable for door shutters of 851 to 1000mm width and of weight of 61 to 80 Kg complete all as specified and directed. |
| 49 | S&F 12mm thick particle board prelaminated on both sides as in panel of door shutters partition wall, work stations including beading etc.omplete all as specified and directed. |
| 50 | Supply and fix sheet glass 5.5 mm thick of selected quality (tinted glass/plane) exc. 0.5 sqm each fixed to aluminium frame work with necessary rubber beading complete all as specified and directed. |
| 51 | Supply and fix sheet glass 5.5 mm thick of selected quality (tinted glass/plane) n. exc. 0.5 sqm each fixed to aluminium frame work with necessary rubber beading complete all as specified and directed. |
| 52 | S&F for powder coated aluminium doors shutters,( thickness of powder coating not less than 50 micron) alumonium section weighing 0.55 kg/m incl necessary joining cleats, glazing clips, rubber neoprene packing , handels 2 Nos in each door , hinges, anodised aluminium snap beading screws etc. complete all aspecified and directed. |
| 53 | S&F brass body mortice lock vertical type size 100mm 4 lever, including escutcheon plate and two No keys fixed complete all as specified and directed. |
| 54 | Surface properly cleaned by wire brush including removing of debries/domolished material obtained from roof out from defence land complete all as specified and as directed. |
| 55 | S&F for expansion/ crumple joint treatment of EPDM/ Polymer polybend water proofing membrane of 1.5mm thick and width of 200mm affixed with epoxy resin adhesive on crumple gaps and including over top surface finished of 2mm thick aluminium cover plate width of 250mm duly holed and capsule slotted on either side and fixed with SS screw etc complete all as spd and directed. |
| 56 | S&F for expansion/ crumple joint treatment of EPDM/ Polymer polybend water proofing membrane of 1.5mm thick and width of 200mm affixed with epoxy resin adhesive on crumple gaps and including over top surface finished of 2mm thick SS cover plate (304 grade) width of 250mm duly holed and capsule slotted on either side and fixed with SS screw etc complete all as spd and directed. |
| 57 | S&F plain galvanised steel sheeting 0.80mm thick and 250mm wide to covering of crumple expansion joints/ Gaps on vertiucal/ Horizontal surface, steeped flashing or by fixing screws etc complete all as specified and directed. |
| 58 | M&L for guiniting work to RCC work in coloumn, chajjas, balconies, slabs, landings etc by removing loose, concrete, incl removing rust with short blasting and cleaning of surface with wire brush and applying epoxy treatment to rusted reinforcement and including S&F welded wire mess fabric or wire not less than 95x95x3mm adhesive plaster grade for concrete admixture and providing guniting pressure 2.00/2.50 Kg/Sq cm with admixture 1 part of cement and 3.50 part of sand and thickness 50mm average and making the surface even and smooth including necessary formwork and 10mm thick with CM 1:4 plaster over repaired surface with WPC complete all as specified and directed. |
| 59 | Demolition of brick work or stone/boulder masonry built in cement mortar up to four stories complete all as specified and directed. |
| 60 | M&L for brick work with subclass 'B' bricks, straight or curved on plan exc 6 M mean radius built in CM 1:6 complete all as specified and directed by Engr In Charge. |
| 61 | M & L rendering 10mm thick on ceiling in cement mortar 1:3 finished fair and even smooth without using extra cement up to four storey height bldg complete all as specified and directed. |
| 62 | M&L for preparation of new surface and applying two coat of distemper on wall/ceiling over with 1mm thick JK/Birla wall care putty on walls complete all as specified and directed. |
| 63 | M&L for prepration of old plastered or unplastered surfaces of walls and applying two coat of approved shade of oil emulsion distemper with 1mm thick JK/Birla wall care putty on walls, including repairing of pot holes and cracks with putty, take it plaster where it required complete all as specified and directed. |
| 64 | M&L for preparing surfaces of new plaster on walls and applying exterior two or more coats of APEX/WEATHER over 3mm putty including priming coat of exterior primer applied complete all as specified and directed. |
| 65 | Material & Labour for prepration of old plastered or unplastered surfaces of walls and applying exterior two or more coats of APEX/WEATHER over 1mm putty including priming coat of exterior primer applied complete all as specified and directed. |
| 66 | S&F precast machine pressed PCC interlocking paver block of 80 mm thickness, M-40 grade of any shape and size confirming to IS -15658-2006 with grey cement and pigment as approved and 80mm thick plain cement concrete, type D-2, 1:4:8, (using 40mm graded stone aggregate) as in sub base flooring, surface finished even and dismentling complete all as specified and directed. |
| 67 | M & L for 75 mm thick PCC 1:3:6 type C2 as in Plinth Protection using 40 mm stone aggregate including making joints & filling with sand bitumen mastic as per incliding dismentling complete all as specified and directed. |
| 68 | Taking down rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed. |
| 69 | S&F for 75 mm dia pvc pipe Stack clamps out of 50 mm by 5mm flat iron and 16mm dia round iron stays,enlcuding bolts and nuts and securing ends of stays to wall or roof as percomplete all as complete all as specified and directed by Engr In Charge. |
| 70 | S&F for 110 mm dia pvc pipe Stack clamps out of 50 mm by 5mm flat iron and 16mm dia round iron stays,enlcuding bolts and nuts and securing ends of stays to wall or roof as per complete all as specified and directed by Engr In Charge. |
| 71 | S&F for PVC SWR bends 110 mm complete all as specified and directed. |
| 72 | S&F PVC SWR bends 75 mm complete all as specified and directed. |
| 73 | S&F for PVC (SWR) pipes 110 mm single socketed, in any length with solvent cement joints fixed to walls/laid in floors incl stack clamps of stainless steel with bolts & nuts etc complete all as specified and directed. |
| 74 | S&F for PVC (SWR) pipes 75 mm single socketed, in any length with solvent cement joints fixed to walls/laid in floors incl stack clamps of stainless steel with bolts & nuts etc complete all as specified and directed. |
| 75 | Surface dressing n exe 15 cm deep in hard/dense soil complete all as specified and directed. |
| 76 | Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 de[th for foundation etc or for shafts well cesspits manholes pier holed etc 10 Sqm on plan and n.exc 1.5m in depth and getting out in hard and dense soil complete all as specified and directed. |
| 77 | M&L PCC 1:4:8 type D2 (using 40 mm graded stone aggregate) as in Foundations filling and mass concrete complete all as specified and directed. |
| 78 | M&L for RCC M-25 (design mix) ( using 20 mm graded stone aggregate ) as in foundation, including rafts, footing, foundation beams, plinth beams, bases for columns etc basement slabs complete all as specified and directed. |
| 79 | M&L for RCC M-25 Design Mix concrete (using 20mm graded aggregatet) as in columns, pillars, piers, post and struts complete all as specified and directed. |
| 80 | M&L for RCC M-25 Design Mix concrete (using 20mm graded aggregate) as in RCC bend, lintels over 1.5 span etc, complete all as specified and directed. |
| 81 | M&L for form work to sides of concrete foundations, footings, bases of columns, sides and soffits, plinth beams and similar work with rough finished complete all as specified and directed. |
| 82 | M&L for form work to sides and soffits of floor or roof beams, bands, lintels cantilivers shelves etc with rough finished complete all as specified and directed. |
| 83 | M&L for form work to sides of pillars , posts struts, piers, coloumns and stanchions etc with rough finished complete all as specified and directed. |
| 84 | M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surface, finished even and smooth without using extra cement complete all as specified and directed. |
| 85 | S&F roof trusses (framed), trussed, purlins,crane gantries, rails and fastnings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc confirming to Fe-290 Gde E-165 complete all as specified and directed. |
| 86 | S&F 10mm thick MS Plates (plain or chequered) square cut or notched (ordinary and counter sunk) forming holes,weldied incl all necessary bolting or riveting etc with roof trusses complete all as specified and directed. |
| 87 | S&F for flat iron fillets 40mmx6mm thick wind ties for roof covering securing with bolts etc including all necessary drilling, bolting or riveting etc.and similar work conforming to Fe 290 gde E 165 complete all as specified and directed. |
| 88 | S&F for mild steel TMT bars 10mm dia and over cut to length bend to shape required including cranking bending spirally for hooping for columns, hooking ends and binding with including mild steel wire not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 89 | S&F for mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirupps, spacers and binders but in stirupps and binding with including mild steel wire not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 90 | S&F2mm thick fiber glass translucent corrugated sheeting with two corrugation side lap fixed with coach screw and washer in roof, wall complete all as specified and directed. |
| 91 | M & L for broken stone hard core of gauge not exc. 63mm, deposited, spread and levelled in layers not exc. 15cm thick, watered and well rammed to a true surface all as specified and directed. |
| 92 | M & L for 100 mm thick PCC 1:4:8 type D2 (using 40mm graded crushed stone aggregate) as in sub base, floors and pavings etc. including using plate type electric vibrator complete all as specified and directed. |
| 93 | M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed. |
| 94 | S&F Mild steel, plain, 1mm th black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed. |
| 95 | S&F Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed. |
| 96 | M & L for PCC 1:2:4 type B2 (using 40mm graded stone aggregate ) as in surface channels and drain including necessary form work complete all as specified and directed. |
| 97 | Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and directed. |
| 98 | M&L for preparing new plastered surface of wall and applying three coats of white wash on wall etc all as specified and directed. |
| 99 | M&L for preparing surfaces of new plaster Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm), complete all as specified and directed. |
| 100 | Returning, filling in trenches, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed. |
| 101 | Removing excavated soil not exceeding 50 m distance and depositing where directed at alevel n exc 1.5 metre above the starting point . complete all as specified and directed. |
| 102 | S&F wall mounted fan of 400 mm sweep, 03 blades aerodynamically balanced with 60 degree oscillation, air delivery not less than 55 M3/Min, 1350 RPM, 230 V, 50Hz and Noise level not more than 64 dB with 2 years warranty complete all as specified and directed.including necessary fixing arrangement for proper fixing in wall as per site requirement complete all as specified. |
| 103 | M&L for Point wiring using approved colour coding as per IS, with stranded copper conductor 1.5 Sq. mm (nominal area), single core, PVC insulated and unsheathed stranded cable 1100 volts grade (FRLS), ISI-694 marked in and including heavy duty, PVC concealed conduit after cutting, chasing the wall etc and making good of disturbed surface, including all accessories etc, heavy duty ISI marked, including mild steel sunken boxes with earth dolly duly powder coated suitable for modular plates of required size, covered with modular plates, suitable for modular switches, sockets etc including PVC insulated stranded copper conductor 1.5 Sqmm (nominal area) (FRLS) single core cable as earth continuity conductor to common earth and connecting to earth dolly. ( Note- Modular Switch and sockets will be measured and paid seperately). |
| 104 | All as per item No-103 above but one fan/exhaust fan and wall mounted fan point controlled by one SP switch. |
| 105 | All as per item No-103 above but for one 3 pin socket out let, 6 Amps on Independent board |
| 106 | All as per item No-103 above but for one 3 pin socket out let, 6 Amps on same board |
| 107 | All as per item No 103 above but with 2.5 Sq mm cable for Independent board one 3 pin 15 Amps socket outlet including single core 2.5 Sq mm PVC insulated copper conductor unsheathed 1100 v grade IS -694 FR LS cable for continuous earth wire required size all as specified and directed. |
| 108 | S & F Modular switch 1 way 6A, 1 modules suitable for 240 volt AC Complete all as specified and directed. Make for item No 6 to 9 - Crabtree series of Havells/ Myrius of Legrand / Northwest switches of WIPRO / Vivace of Schneider / ORIS of L&T / Zenit of ABB/ Myrah of Anchor. |
| 109 | S & F Modular Socket, 6A - 3 pin combined 2 module, suitable for 240 volt AC Complete all as specified and directed . |
| 110 | S&F Modular switch 1 way 16A, 1 modules suitable for 240 volt AC Complete all as specified and directed . |
| 111 | S & F Modular Socket, 16A - 2/3 pin combined 2 module, suitable for 240 volt AC Complete all as specified and directed. |
| 112 | Supply and fixing of ceiling roses, surface bakelite 65mmx50mm 2 or 3 terminals , PVC/Polycarbonate, isolated body fixed on PVC round block complete all as specified and directed. |
| 113 | Supply and fixing wall mounted LED batten extruded aluminium heat shrink provided for efficient heat dissipation and integrated electronic driver ,20 watt LED fitting, 4000K , 230 Volts, diffused optics ,etc complete with all accessories , connecting up with twin core twisted flexible copper conductor cable from ceiling rose to fitting, and testing complete all as specified and directed by the Engineer- In- Charge. Make CCS-100-20-65-HL2-DP-NWH of Crompton / Cat Part No SLE BT 20 G1 of Surya / Cat Part No LHEBFOPN137W020 of Havells |
| 114 | Supply and fiing of exhaust fan , metal body AC single phase,230v , of size 300mm sweep with blades frame and louver complete as specified and directed . |
| 115 | M & L for submain wiring with two run of 4.0 sqmm single core PVC insulated but unsheathed FRLS cable of specified size of multistranded copper conductor 1100 volts grade IS:694 marked and one run of 4.0 sqmm PVC insulated but unsheathed FRLS cable for earth continuty conductordrawn through and under suitable size of rigid non metallic PVC conduit , medium grade, ISI marked ( not less than 20 mm dia) complete with all acessories and fittings all laid/fixed concealed in wall/ceiling or surface in wall and surface conduit on ceiling, and also include the specified runs of specified size earth continuity conductor of similar type cable complete all as specified - 2 Runs of 4.0 Sqmm single core and one run of 4 sqmm single core cable. |
| 116 | Supply and fixing in replacement MCB distribution board with Bus bar 200A neutral link ,earth bar made out of CRCA mild steel sheet surface mounting SPN 4 way 230 volts double door type complete all as specified and as directed by Engineer-in-Charge. Note :- MCB shall be measured and paid seperately. Make - Crabtree series of Havells/ Myrius of Legrand / Northwest switches of WIPRO / Vivace of Schneider / ORIS of L&T / Zenit of ABB/ Myrah of Anchor. |
| 117 | S&F MCB SP 6 to 32 Amps 10 KA, 240 volt 'B' Series all as specified and directed. |
| 118 | S&F MCB SPN 32 Amps 10 KA, 240 volt 50 Hz 'C' Series all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 20, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Jul 27, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 5 daysJul 27, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysJul 30, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 8 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender