Tender For Left Over Work Of Charan Commercial Complex And Adjacent Premises Near Ihsdp Site At Dharamshala (H.P.)
Tender Value
1.45 Crore
Estimated cost
Bid Submission
13 Jul 2026
1 days left
EMD
2.91 Lakhs
Bank guarantee accepted
Document Fee
5000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kangra → Himachal Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Left Over Work Of Charan Commercial Complex And Adjacent Premises Near Ihsdp Site At Dharamshala (H.P.)
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 08-Jul-2026 | CORRIGENDUM | Date | 13-Jul-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. ALL KINDS OF SOIL |
| 2 | Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains , including dressing of sides and ramming of bottoms, including getting out the excavated soil/ordinary rock and disposal of surplus excavated soils upto all lead and lift as per direction of Engineer In Charge. |
| 3 | Providing and laying cement concrete mechanically mixed 1:4:8 (1 cement : 4 sand : 8 graded stone aggregate 40mm nominal size) curing complete excluding cost of form work in foundation and plinth including carriage of material upto all leads and lifts and as per direction of Engineer In Charge. |
| 4 | Cement concrete pavement with1:2:4 (1cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size), including finishing complete |
| 5 | Providing and laying cement concrete mechanically mixed 1:3:6 (1 cement : 3 sand : 6 graded stone aggregate 40mm nominal size) curing complete excluding cost of form work in foundation and plinth including carriage of material upto all leads and lifts and as per direction of Engineer-In-Charge. |
| 6 | Providing and laying 80mm thick heavy duty precast cement concrete inter locking coloured paver blocks vibro compacted upto M-40 grade i/c border or kurb block grey or colored over sub-base of concrete with 25mm thick average thickness of cement mortar 1:4 (1 cement : 4 sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks i/c curing rubbing & polishing complete (Sub base concrete floor to be paid for separately) |
| 7 | Providing and filling of stone solling under floors /boulder filling behind retaining walls of selected hard stone including carriage of material in all leads & lifts and as per direction of Engineer In Charge. |
| 8 | Providing weepholes in brick masonry / stone masonry /plain reinforced concrete abutment, wing wall, return wall with 110 mm dia PVC pipe (weight should not be less than 4kg/cm2), extending through the full with of the structures with slope of 1(v):20(H) towards drawing face complete as per drawing and technical specification clauses 614, 709, 1204.3.7, including carriage of material in all leads and lifts and as per direction of Engineer in Charge. |
| 9 | Steel work welded in built up sections / hollow section, in beams joists channels ,angles ,tee ,flats with connection plates or angle cleats as in main and cross beems, hip and jack rafters, purlins connected to common rafters and the like and in In gratings framed guard bars, ladders, railling,brackets and similar works trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of red lead paint including carriage of material upto all leads and lifts and as per direction of Engineer In Charge. |
| 10 | Providing and fixing 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with repainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accessories as required as per approved brand (TATA durashine) and direction of Engineer-In-Charge. |
| 11 | Providing and fixing ridges or hips 60 cm wide overall with 0.60mm thick preprinted steel sheets in roofing with hot dipped metallic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5microns primer coating + backcoat of polyster of 5 microns over 5microns primer coating i/c fixing with prepainted hooks, bolts and nuts complete with all accessories as required as per the direction of Engineer-In-Charge. |
| 12 | Providing and fixing valley 60 cm overall 0.60mm thick preprinted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster organic outing of 20 microns over 5 microns primer coating back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted hooks, bolts and nuts complete with all accessories as required as per the direction of Engineer-In-Charge. |
| 13 | Painting two coats (excluding priming coat) on new steel and other metal surface under coat with ready mixed paint brusing to give an even shade including cleaning the surface all dirt, dust and other foreign matter with readymixed paint other than white. |
| 14 | Providing and laying Reinforced Cement Concrete (RCC Grade M25) in Open Foundation complete as per Drawing and Technical Specifications including cost of form works and carriage of material upto all leads and lifts and as per direction of Engineer in charge. |
| 15 | Providing Tor steel reinforcement Fe-550D for R.C.C. work including bending, binding and placing in position complete upto all level including carriage of material upto all leads and lifts and as per direction of Engineer In Charge. |
| 16 | Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centering, shuttering, strutting and propping etc.and removal of the same for insitu-reinforced concrete & plain concrete work in drains.i/c carriage of materials of all leads and lifts as per Engg. in Charge. |
| 17 | Providing & making Gabion structure with MechanicallyWoven Double Twisted Hexagonal Shaped Wire mesh Gabion Boxes as per IS 16014:2012,MORTH Clause2500,of required size,Mesh Type10x12 (D=100 mm with tolerance of ± 2%) Zinc coated, Mesh wire diameter 3.0mm, mechanically edged/selvedged with partitions at every 1m interval and shall have minimum10 numbers of openings per meter of mesh perpendicular to twist, tying with lacing wire of diameter 2.2mm,supplied @3% by weight of Gabion boxes, filled with boulders with least dimension of 200mm, as per drawing, all complete as per direction of Engineer-in-charge. |
| 18 | Providing and fixing (500 X 450) mm size Logo & Text of Smart City cut in ACP Sheet and printing on vinyl sheet fix with Acrylic sheet on railing as per drawings and techanical specification approved by Engineer-In-Charge. |
| 19 | Brick work with common burnt clay F .P .S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 20 | 15mm Cement plaster in cement mortar 1:6 (1 cement : 6 sand) in single coat on the fair/rough side of brick/ concrete/ stone walls for plastering upto all floor level including arrises,internal rounded angles, chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth. |
| 21 | Backfilling behind retaining wall/ abutment/ wing wall/floor/ subgrade and return wall and compaction of backfilling material should be consolidated with power ramer complete all as per drawing and Technical Specification and as directed by Engineer-incharge. |
| 22 | Providing and laying 15mm average thick slate flooring, 20 mm (average) thick base of cement mortor 1:4 (1 cement :4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab. including rubbing and polishing complete and carriage of material up to all leads and lifts and as per direction of Engineer In Charge. |
| 23 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete including carraige of materials upto all leads and lifts as per Engineer-In- Charge. |
| 24 | Finishing wall with weather proof exterior grade emulsion of approved design on undecorated wall surfaces (two coats) to give an even shade and final finish after thoroughly cleaning the surface to remove all dirt, dust and other foreign matter etc. as per approved brand (Burger, Shalimar, Asian paints, ICI Nerolac) including sand paper smooth complete including carraige of materials upto all leads and lifts as per Engineer-In- Charge. |
| 25 | Providing and laying autoclaved aerated cement blocks masonry with 150mm/ 230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete including carriage of material upto all leads and lifts and as per direction of Engineer-In-Charge. (The payment of RCC band and reinforcement shall be made for seperately) |
| 26 | Providing and laying natural cobble stone flooring (100x100) and thickness is (80-100)mm, laid over 25mm average thickness of cement mortar 1:4 (1 cement : 4 sand) laid over and i/c pointing and curing complete as per the design patteren and colour approved as per Engg.-In- Charge. |
| 27 | Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401 |
| 28 | Providing and fixing of G.I. wire fencing, 4mm thick corresponding to SWG-8. 75mm.x 75mm mesh with all taxes and including carriage of material upto all leads and lifts and as per direction of Engineer in charge. |
| 29 | Supply of Surface Down Light 3000K with Integral driver & completely made in India luminaire. The luminaire’s shall be made of Exteruded aluminium powder coated. Optical compartment is sealed with toughened glass using Silicon gasket ensuring IP65 & IK06 protection and lifelong performance.The LEDs shall have minimum CRI ≥70 (White LED) & shall have SDCM≤5. The luminaire shall have wattage 9W and shall deliver 810 lumens. Beam angle of the Luminaire shall be 60 deg. Fixture shall operating temperature range of 0°C to 45°C. Input Voltage Range of 140 - 280V AC. 2 stage Constant current driver with Inbuilt 3kV surge protection. The luminaire shall have declared life of 50,000 burning hours at L70. Luminaire and Driver must be made in India with same brand. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer along with technical bid. LM80 , RoHS compliance issued by LED luminaire manufacturer, BIS certificate for LED Luminaire. Brand name shall be embossed / engraded on each an every light fixtures. Luminaire and Driver should be Made in India. Luminare, Driver and controller should be with same make. |
| 30 | Supply of Circular Mini Flood Light with Integral driver & completely made in India luminaire. The luminaire’s shall be made of Extruded aluminum housing powder coated he complete luminaire has IP65 & IK06 protection and it comprises of high purity integrated poly carbonate Lens.The LEDs shall have minimum CRI ≥70 (White LED) & shall have SDCM≤5. The luminaire shall have wattage 60W and shall deliver 4800 lumens. Beam angle of the Luminaire shall be 30 deg .Fixture shall operating temperature range of 0°C to 45°C. Input Voltage Range of 140 - 280V AC.. The luminaire shall have declared life of 50,000 burning hours at L70.Luminaire and Driver must be made in India with same brand. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer along with technical bid. LM80 , RoHS compliance issued by LED luminaire manufacturer, BIS certificate for LED Luminaire. Brand name shall be embossed / engraded on each an every light fixtures. Luminaire and Driver should be Made in India. Luminare, Driver and controller should be with same make. |
| 31 | Supply of Circular Mini Flood Light with Integral driver & completely made in India luminaire. The luminaire’s shall be made of Extruded aluminum housing powder coated.The complete luminaire has IP65 & IK06 protection and it comprises of high purity integrated poly carbonate Lens.The LEDs shall have minimum CRI ≥70 (White LED) & shall have SDCM≤5. The luminaire shall have wattage 48W and shall deliver 2600 lumens. Beam angle of the Luminaire shall be 11 deg .Fixture shall operating temperature range of 0°C to 45°C. Input Voltage Range of 140 - 280V AC.. The luminaire shall have declared life of 50,000 burning hours at L70.Luminaire and Driver must be made in India with same brand. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer along with technical bid. LM80 , RoHS compliance issued by LED luminaire manufacturer, BIS certificate for LED Luminaire. Brand name shall be embossed / engraded on each an every light fixtures. Luminaire and Driver should be Made in India. Luminare, Driver and controller should be with same make. |
| 32 | Supply of 1000 mm length RGBW Linear Wall Washer with Non-integral driver & completely made in India luminaire. Luminaire must use Single LED of RGBW ChIPand not descrete individual LEDs of each colour for colour effect. The luminaire’s shall be made of Extruded aluminum housing powder coated in grey. The complete luminaire has IP66 & IK07 protection and it comprises of high purity integrated poly carbonate Lens.The LEDs shall have minimum CRI ≥80 (White LED) & shall have SDCM≤5. The luminaire shall have wattage 24W and shall deliver 960 lumens. Beam angle of the Luminaire shall be 60 deg .Fixture shall operating temperature range of 0°C to 45°C. Input Voltage Range of 24V DC, Integrated DMX Decoder,No need to additional external decoder. The luminaire shall have declared life of 50,000 burning hours at L70. The luminaire shall be compatible with DMX controller. The luminaire shall automatically addressable using hand-held addressing device. The luminaire shall be capable of 8-bit control of RED, Green, Blue & White (W=4000K) to produce 16.7million colours. Luminaire and Driver must be made in India with same brand. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer along with technical bid. LM80 , RoHS compliance issued by LED luminaire manufacturer, BIS certificate for LED Luminaire. Brand name shall be embossed / engraded on each an every light fixtures. Luminaire and Driver should be Made in India. Luminare, Driver and controller should be with same make. LF01-241-60-CCWG2 |
| 33 | Supply, Installation, Testing and commissioning of DMX Master Controller, with completely made in India product. A stand alone interface for installation in electrical DIN Cabinets with Din rails, which can control from 512 to 1024 and can go up to 2048 channels on 1, 2 or 4 DMX universes. A robust Stand Alone mode and a wide range of trigger possibilities (RS232, Contacts, Clock, NODE x4 ports, Master/slave), USB-C Networks Ethernet, Internet, WIFI compatible when connected to a router Multiple Zone 10 Zone, play 10 scene/sequence per time in Stand Alone ,Memory of Micro SD Card ( max. 256 GB ) and 8Mb Internal memory . Art-Net and sACN from SD card, including triggers (2x512). A master / Save Synchro (32 max wired / 128 max Ethernet) that Commands from the Contacts (speed, scene, dimmer, zone). Default start scene, Scene priority, Cross Fade time between scenes , Automatic Scene Recovery if the power is cut off and 16-bit and fine channel management. Triggers options of RS232 In/Out (16 characters max for RS232 triggers, commands or orders) and UDP / Ethernet triggers and commands (from SDK). Software Requirements with System Compatibility of Windows, Mac, iOS. Flexible, adaptable mounting options ,Should be provided with light show authoring software, Direct line voltage power supports 100—240VAC,Minimum five configurable effects, Using light show authoring software to select from standard five effects, adjust effect settings such as color, speed, and brightness. IP20. Addressing & Programming inclusive and with Five Year Warranty. Brand name shall be embossed on each and every lighting fixtures. |
| 34 | Supply of DMX Splitter, Booster 343 mm Height X 123mm Width X 46 mm Depth with completely made in India product .Input Power DC 12-24V input, 100-240V, 24VDC plug-in power adaptor included Power Consumption 4.5W max and of MS/ Aluminium Housing. Power Consumption of 4.5 Approx and Weight of 1.5Kg .The output terminals should be optically isolated from the input and share a common ground reference. All six output ports should have an independent output driver and ELV transformer to boost the DMX signal. 1: 6 Way DMX Splitter/Booster ,Optically isolated DMX Input/Outputs, Individual coil transformer for each output , Surface/Rack/Floor/Celling mountable with provide mounting accessories ,Refined and filtered data , Cable 3 core 0.75sq.mm .Five Year Warrantyof DMX Signal Splitter+Amplifier - One DMX512 signal Input to six DMX512 outputs, Designed to amplify, distribute and isolate DMX signals in short-runs and localised splitting scenarios. Photo-electric isolation between Input and Output terminals as well as between output terminals among channels. Compensates for any intereference from external sources like AC lines, Electrical equipment operating close to DMX transmission lines.Compact DIN rail enclosure enables easy installation inside most enclosures. |
| 35 | Supply of 6 push button keypad/panel made of aluminium brushed CNC style modular with 6 individual push buttons that can trigger the Dry Port contacts.Output Voltage 12 V DC. A completely made in India product. |
| 36 | Connector 5 Core T Connector |
| 37 | Connector 5 Core S Connector |
| 38 | DMX and Decoder for RGBW Lighting at site Programming Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jul 08, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Jul 13, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 1 dayJul 13, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 1 dayJul 14, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 2 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender