Tender For Welcome Maintenance And Petty Repairs In Md And Otm Accn In Sector- 24,37,38,42 At Chandigarh
Tender Value
17 Lakhs
Estimated cost
Bid Submission
21 Jul 2026
16 days left
EMD
34000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Chandigarh → Chandigarh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Welcome Maintenance And Petty Repairs In Md And Otm Accn In Sector- 24,37,38,42 At Chandigarh
BOQ
| Sl. No. | Item Description |
| 1 | Material and labour for preparing old treated wall surfaces by washing , rubbing down and stoping of distempered and painted Surface of any description over 10cm girth or width, not otherwise described and applying one coat of plastic / interior emulsion paint with roller and brushes complete all as specified and directed in clause 17.3,17.4,17.5 & 17.6 &17.16 of SSR Part-I and clause 17.2 of SSR Part -II . |
| 2 | Material and labour for preparing old treated wall surfaces by washing , rubbing down and stoping of distempered and painted Surface of any description over 10cm girth or width, applying wall care putty 2 mm thick (average thickness) of approved quality as specified in clause 15.19 of SSR Part-I and one coat of primer , finally applying two coats of plastic / interior emulsion paint with roller and brushes complete all as specified and directed in 17.3,17.4,17.5 & 17.6 &17.16 of SSR Part-I and clause 17.2 of SSR Part -II . |
| 3 | Material and labour for preparation of old painted wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of primer in stair case railings and similar items complete all as specified and directed in clause 17.3,17.4,17.5 ,17.6 &17.10 of SSR Part-I and clause 17.2 of SSR Part -II . |
| 4 | Demolition of un-reinforced cement concrete exc 15cm thick on any description and in any position (in sunken portion) not other wise specially provided for and removing all demolished material/debris up to 1.5 Km form the site and depositing where directed complete all as specified and directed. |
| 5 | Material and labour for plain cement concrete 1:7:12 type F-2 using 40mm graded crushed stone aggregate as in sunken floor filling and mass concrete complete all as specified and directed. |
| 6 | Water proofing treatment to sunken portionand adjoining walls of kitech. WC, Bath & Toilet, etc. : 15 mm plaster in cement mortar (1:3) after roughning and cleaning the surface mixed with WP compound as per manufacturer’s instructions shall be provided on sunken portion while the concrete is green complete all as specified and directed(a) Apply cement slurry to the surface @ 0.488 kg /Sq. m of cement mixed with Acrylic based polymer modified cementious composite compound @ 0.253 kg/Sq. m and the surface shall be allowed to air cure for 4 hours. (b) Apply another layer of cement slurry @ 0.242 kg/Sq. m of cement mixed with Acrylic based polymer modified cementious composite compound @ 0.126 Kg/Sq. m and the surface will be allowed to air cure for 4 hours. (c) Curing the sunken portion with water minimum for 48 Hrs by ponding. (d) Paste one layer of 3mm thick APP membranne with bitumen by torch application to the treated sunken surface. (e) Joints/Traps/WC/soil pipes shall be properly sealed with approved sealing compound of make mentioned as specified. |
| 7 | Material and labour for cleaing and removing all scale and dirt etc, from tanks exceeding 500 & n.exc 1000 ltr capacity of tank from mouths of circulating pipes with & including disconnecting & refixing in all respects including fittings such as tank nipple,elbow,socket etc along with provision of new float valve PVC 20mm dia complete all as specified and directed |
| 8 | Supply and fixing for stainless steel fancy type curtain rods of 20mm dia.with suitable number of stainless steel brackets & stainless steel knob as per site requirement fixed in repair on complete all as specified and directed |
| 9 | Hacking out old broken glass (any thickness, size, quality or description) from wooden/steel frame complete all as specified and directed. |
| 10 | Supply and fixing for 3mm thick ordinary quality cut to size glass panes ( size of each pane ranging from 0.50 Sqm to 1.50 Sqm as ordered ) with silicon of oil putty of approved quality fixed including removing loose putty in any floor ie upto vth floor with and including requisite ladder or scaffolding and safety measures complete all as specified and directed. |
| 11 | Material and labour for preparing old treated wall surfaces by scraping, washing, rubbing down and stopping of distempered/ painted surfaces and applying one coat of oil emulsion distemper (OBD) on wall surfaces with roller and brushes complete all as specified and directedin clause 15.10 & 15.14 of SSR Part-I and clause 15.2 of SSR Part -II . |
| 12 | Material and labour for preparing old treated wall surfaces by scraping,washing, rubbing down and stopping of distempered /painted surfaces and applying two coats of oil emulsion distemper (OBD) on wall surfaces with roller and brushes complete all as specified and directed in clause 15.10 & 15.14 of SSR Part-I and clause 15.2 of SSR Part -II . |
| 13 | Material and labour for preparing old treated wall surfaces by scraping,washing , rubbing down and stoping of distempered / painted Surface of any description over 10cm girth or width, applying wall care putty 2 mm thick (average thickness) of approved quality as specified in clause 15.19 of SSR Part-I and one coat of primer , finally applying two coats of oil emulsion distemper (OBD) with roller and brushescomplete all as specified and directed in clause 15.10 & 15.14 of SSR Part-I and clause 15.2 of SSR Part -II . |
| 14 | Material and labour for preparing old treated ceiling surfaces by washing, rubbing down and stopping of distempered / painted surfaces and applying one coat of oil emulsion distemper (OBD) on ceiling surfaces complete all as specified and directed in clause 15.10 & 15.14 of SSR Part-I and clause 15.2 of SSR Part -II . |
| 15 | Material and labour for preparation of old painted wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coats of Synthetic enamel paint (Ordinary tint).complete all as specified and directed in clause 17.3,17.4,17.5 & 17.6 &17.10 of SSR Part-I and clause 17.2 of SSR Part -II . |
| 16 | Material and labour for preparation of old painted steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint. complete all as specified and directed in clause 17.3,17.4,17.5 & 17.8 &17.10 of SSR Part-I and clause 17.2 of SSR Part -II . |
| 17 | Material and labour in repair for 18mm thick both side pre-laminated high density high moisture resistances (HDHMR) board any colour wood grains, with white base paint finish UV HDHMR corner side rounding with edge bending tape as in shutters for C.B.,cabinets,drawers, shelves any shape and sizes will be made up by machines matching with final finish (UV) complete all as specified and directed (Note :- Design and colour shall be approved by GE) Make:- Bhutan Tuff India, Green Ply, Archid |
| 18 | Supply and fixing in repair 2nd class hard wood plain fillets sectional area exc. 6sqcm n.exc. 13 Sqcm clean sawn wrought , secured with nails and painting the surfaces with primer and synthetic enamelled paint complete all as specified and directed. |
| 19 | Supply and fixing for solid PVC door frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tube complete all as specified and directed. |
| 20 | Supply and fixing for factory made solid panel PVC door shutter 30mm thick (style) one side prelam pvc in place of plain and another side decorative, consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width strucks inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either to side and as gap insert for top rail & bottom rail panelling to be fitted in MS frame welded/sealed to stiles and rails with suitable PVC sheet beading and jointed together with solvent cement, supply and fixing in the frame at site as specified of drawing complete all as specified and directed. |
| 21 | Supply and fixing for flush shutters, 35 mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. |
| 22 | Supply and fixing for 2nd class hardwood glazed and skelton shutters 35 mm thick open rebated and prepared to receive glass, gauge etc(without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, stiles and rails as specified in SSR Part I section 8 clause 8.20 (a) supplied and fitted to chowkhats complete all as specified and directed. |
| 23 | Supply and fixing in repairs double legged door stopper of aluminium alloy with rubber complete all as specified and directed |
| 24 | Supply and fixing for butt hinges, medium weight, Stainless steel and fixed of size 150mm complete all as specified and directed. |
| 25 | Taking down shutter of any description exc 1 sqm and n/exc 2 sqm each incl removing from the premises complete all as specified and directed. |
| 26 | Taking down chowkhat or frame with shutter (without taking off shutter from the frame) n. exc 1.5 sqm incl removing from the premisescomplete all as specified and directed |
| 27 | Supply and fixing in repairs vitreous china wash down water closet single piece-WC with UF seat cover, hinges, fixing accessories, cistern fittings, size 655x665x760, S trap-300mm including connection to drain pipe etc complete all as specified and directed |
| 28 | Supply and fixing in repair vitreous china squatting pan,”Orissa” pattern, size 580mmX440mm, white, with integral foot rests, ‘S’ trap (excluding flushing cistern and flush pipe) with and including,PVC/CI floor trap necessary demolition and provision of lime concrete bedding complete all as specified and directed |
| 29 | Supply and fixing in repairs PVC low level flushing cistern of capacity 10 ltrs with inlet, ball valve, float and handle including brackets and flush pipe of PVC 32mm dia complete all as specified and directed. |
| 30 | Supply and fixing in repairs kitchen sink with drainage board made of stainless steel 1 mm thick with plugs washers and waste pipe and coupling including bedding in cement mortar on dwarf walls including brackets and connecting union to pipe overall size of sink 915 x460 mm and bowl size 410x330x160 mm complete all as specified and directed. |
| 31 | Supply and fixing in repair vitreous china wash down water closet pan (pedestal pattern), white with P or S trap with and including floor trap and pipe 100mm dia and provision of plastic seat cover complete all as specified and directed |
| 32 | Supply and fixing wash hand basin, vitreous china, flat back , white of size 550X400mm, with and including PVC connection, CP pillar tap, CP waste coupling, PVC waste pipe, fixed to wall with suitable fastners of adequate size and strength ,fixed as in repairs complete all as specified and directed. |
| 33 | Supply and fixing in repairs plate rack made out of 1 mm thick stainless steel sheet of size 75 cm x 90 cm x 25 cm with all internal fittings (as per sample) complete all as specified and directed. |
| 34 | Supply and fixing in repairs waste coupling for wash basin and kitchen sink complete as specified and directed. |
| 35 | Supply and fixing in repairs PVC waste pipe 25 mm dia 750 to 800mm long fixed to waste fitting of wash basin including socket suitable for waste fitting complete all as specified and directed. |
| 36 | Supply and fixing in repairs centre hole basin mixture 15 mm dia chromium plated complete all as specified and directed. |
| 37 | Supply and fixing in repairs chromium plated fancy type concealed stop cock /angle valves/ two way angle valve with cup cast copper alloy screwed down high pressure, screwed both ends for iron pipes or for unions for 15 mm bore pipe complete all as specified and directed. |
| 38 | Supply and fixing in repairs chromium plated fancy type long body bib taps with cast copper alloy screwed down, screwed for iron pipe or for brass ferrule for 15 mm bore pipe complete all as specified and directed. |
| 39 | Supply and fixing in repairs 150 mm square shower rose of Chromium plated brass for fixing 15 mm pipe with shower arm size 195 mm long with bend of 45 degree with flange complete all as specified and directed. |
| 40 | Supply and fixing in repairs chromium plated wall mixture with connection for shower arragement complete all as specified and directed. |
| 41 | Supply and fixing in repairs water jet for ETWC chromium plated with PVC connection complete all as specified and directed. |
| 42 | Supply and fixing for CP heavy duty extension pieces 15mm bore and 25 mm long in repairs complete all as specified and directed. |
| 43 | Supply and fixing in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube andABS wall hook including making connections and fixed in position ccomplete all as specified and directed. |
| 44 | Supply and fixing in repairs PVC connections 15mm dia & 450mm long with PTMT nuts complete all as specified and directed. |
| 45 | Supply and fixing in repairs 600 mm x 450 mm bevelled edge mirror of selected quality glass mounted on 6 mm thick commercial plywood and fixed to wooden plugs with chromium plated brass screw and cup washer complete all as specified and directed. |
| 46 | Supply and fixing in repairs chromium plated toilet paper stand complete all as specified and directed. |
| 47 | Supply and fixing in repairs chromium plated towel ring complete all as specified and directed. |
| 48 | Supply and fixing in repairs glass shelf with chromium plated brackets of suitable size complete all as specified and directed. |
| 49 | Dismantling floor, stone, hearth or wall tiling/terrazo/sotne slab including cement mortar bedding/backing complete or in patches and removing rubbish off the premises complete all as specified and directed. |
| 50 | Material and labour for glazed coloured ceramic tiles 450 x 350 mm x 7 mm thick in vertical wall complete or in patches surfaces set and jointed in neat cement slurry and pointed in white cement using pigment to match the shade of tiles incl plastering 10mm thick in CM 1:4, complete all as specified and directed |
| 51 | Material and labour for non skid ceramic coloured tiles Edge cut 7 to 8 mm thick (Square/rectingular)area of each tiles exceeding 0.11 Sqmbut not exceeding 0.18 Sqm (400 x 400mm) as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match incl screeding 15mm thick in CM 1:6, complete all as specified and directed. |
| 52 | All as per Serial item No 51 above but as in vertical surfaces incl rendering 10mm thick in CM 1:4 complete all as specified and directed. |
| 53 | Material and labour for vitrified ceramic tiles light shade 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm( 600 x 600 ) in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement incl screeding 15mm thick in CM 1:6, complete all as specified and directed |
| 54 | All as per serial item No 53 but as in vertical surfaces incl rendering 10mm thick in CM 1:4,complete all as specified and directed. |
| 55 | Supply and fixing for 16 to 18 mm thick granite stone slabs mirror polished of colour and shade as approved by GE, machine cut bedded & jointed with grey cement slurry and pointed in white cement with admixture of pigment to match the shade of granite stone fixed as in steps, jambs, pillars window cills, cooking platforms & the like over a screed bed of 15mm thick CM 1:6 etc complete all as specified and directed |
| 56 | Rounding to edges of stone slabs one edge , such as in steps , cooking platform , and other similar situations complete all as specified and directed |
| 57 | Supply and fixing for 30mm width of flap continuous (piano) hinges MS bright finish or electrogalvanised complete all as specified and directed. |
| 58 | Supply and fixing for stainless steel handle 100mm complete all as specified and directed. |
| 59 | Supply and fixing of aluminium magnetic door catcher of suitable size for each shutter of cupboard complete all as specified and directed. |
| 60 | Supply and fixing for aluminum anodised barrel tower bolts 150mm long, of extruded section and fixed complete all as specified and directed.. |
| 61 | Supply and fixing in repair 300mm size aluminium alloy anodised sliding door bolt with hasp & staple(bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolt and sliding bolt of extruded section or cast alluminium alloy complete all as specified and directed |
| 62 | Supply and fixing in repairs Galvanized mild steel wire mesh 0.56 mm nominal dia of wire and average width of aperature 1.18mm and fixed with tinned takes or galvanised Wire staples complete all as specified and directed. |
| 63 | Supply and fixing for 15mm bore tubes medium grade galvanised iron with all new fitting and fixed to walls and ceiling or laid in floors including taking down old unserviceable steel tubing complete all as specified and directed. |
| 64 | Supply and fixing 20 mm bore tubes medium grade galvanised iron with all new fitting and fixed to walls and ceiling or laid in floors including taking down old unserviceable steel tubing complete all as specified and directed. |
| 65 | Material and labour for preparation of new wooden surfaces and applying two coats of synthetic enamel paint over one coat of pink primer over 10 cm width or girth complete all as specified and directed. . |
| 66 | Dismantling of cast iron /PVC/AC/SGSW pipes 100mm dia jointed in cement mortar and taking out of trenches, if required complete all as specified and directed. |
| 67 | Supply and fixing for PVC(SWR) 110mm dia soil waste and rainwater drainage pipes single socketed in any length with rubber ring joint fixed to wall complete all as specified and directed. |
| 68 | Supply and fixing for PVC (SWR) 110mm dia bends complete all as specified and directed. |
| 69 | Material and labour for 40 mm thick cement concrete type B1, 1:2:4 (using 20mm graded stone aggregate) finishing sufaces even and smooth without using extra cement complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jun 29, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 21, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 16 daysJul 23, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 18 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender