Tender For Provn Of 02 X Toilet Cum Bathroom Blocks For Officers Against Job No 06/Rev/1Sect/2025-26 At Khanabal Military Station Under Ge 861 Ews.
Tender Value
9.71 Lakhs
Estimated cost
Bid Submission
20 Jul 2026
13 days left
EMD
19500
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Anantnag → Jammu and Kashmir
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provn Of 02 X Toilet Cum Bathroom Blocks For Officers Against Job No 06/Rev/1Sect/2025-26 At Khanabal Military Station Under Ge 861 Ews.
BOQ
| Sl. No. | Item Description |
| 1 | Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in any type of soil complete all as specified and as directed by Engineer-in-Charge. |
| 2 | Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, cable, pipes etc. not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in Hard/ dense soil complete all as specified and as directed by Engineer-in- charge. |
| 3 | Material & Labour for PCC 1:4:8 , Type - D2, using 40mm graded stone aggregates as in foundations, filling and mass concrete complete all as specified and directed by Engineer-in-Charge. |
| 4 | Material & Labour for providing RCC1:1.5:3 (nominal mix) M-20 ( using 12.5 mm graded stone aggregate as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns,slab etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed by Engineer-in-Charge. |
| 5 | Removing excavated material/soils to a distance exc 50 m upto 250 m and depositing where directed at a level not exc.1.5 mtr above the starting point, complete all as spefied and as directed by Engineer-in-Charge. |
| 6 | Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25cm thick, in any type of soil complete all as spefied and as directed by Engineer-in-Charge. |
| 7 | Material & Labour for Hardcore of broken stone or boulders ,gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and as directed by Engineer-in-Charge.. |
| 8 | Material & Labour for 75mm thick PCC 1:4:8 , Type - D2, using 40mm graded stone aggregates as in sub base of flooring, filling and mass concrete complete all as specified and directed by Engineer-in-Charge. |
| 9 | Material & Labour for 25 mm thick PCC in Cement Mortar 1:2:4 Type B-0 (using 12.5 mm graded stone aggregate) as in sub base of floor complete all as specified and directed by Engineer-in-Charge. |
| 10 | Material & Labour for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter on rough finished flat surface of concrete complete all as specified and as directed by Engineer-in-Charge. |
| 11 | Material & Labour for Formwork to sides of pillars, posts, struts, piers, columns and stanchions, in square, rectangular or polygonal on rough finished surface of concrete complete all as specified and as directed by Engineer-in-Charge. |
| 12 | Material & Labour for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and as directed by Engineer-in-Charge. |
| 13 | Material & Labour for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. on flat rough finished surface of concrete complete all as specified and as directed by Engineer-in-Charge. |
| 14 | Material & Labour for Brickwork with sub class ‘B’ burnt clay old size bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and as directed by Engineer-in-Charge. |
| 15 | Material & Labour for Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed by Engineer-in-Charge. |
| 16 | Material & Labour for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed by Engineer-in-Charge. |
| 17 | Material and labour for Rendering 15mm thick in Cement Mortar 1:4 , on fair faces of brick work or concrete surfaces of walls , finish even & smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. |
| 18 | Material and labour for Rendering 15mm thick in Cement Mortar 1:6 , on fair faces of brick work or concrete surfaces of walls , finish even & smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. |
| 19 | Material and labour for preparing new plastered surface of wall and applying two coats of cement based paint over and including one coat of alkali resistance primer, complete all as specified and directed by Engineer-in-Charge. |
| 20 | Material and labour for preparing newly plastered surfaces of wall and applying two coats of oil bound distemper over and including one coat of alkali resistance primer complete all as specified and directed by Engineer-in-Charge. |
| 21 | Material & Labour for Non skid ceramic tiles , thickness 7mm to 8mm thick (square/ rectangular), colour as approved by Engineer-in-charge area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm in floor etc set and jointed in neat cement slurry @ 3.00Kg per Sqm and pointed in white or coloured cement to match the colour / shade of tiles , laid over with and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge. |
| 22 | Material & Labour for Glazed ceramic coloured tiles size 450mm x 300mm x 7mm thick as in verticle surface , set and jointed in neat cement slurry @ 3.00Kg per Sqm and pointed in white or coloured cement to match the colour / shade of tiles , laid over with and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge. |
| 23 | Supply and Fixing Vitreous China Table Top Wash Basin of size 550 mm × 400 mm, white/off-white colour, flat back design, complete with and including Single Lever Extended Body Basin Mixer having 15 mm nominal bore connection and minimum 250 mm overall height (or as approved),with and including chromium plated brass body with ceramic cartridge, with and including Chromium Plated waste coupling, Chromium plated bottle trap, waste plug and chain with porcelain stopper, flexible connection pipes and all necessary fittings, fixtures and accessories, complete in all respects as specified and directed by the Engineer-in-Charge. |
| 24 | Material & Labour for 20mm thick granite slab (any type) in one piece machine cut (as approved by Engineer-in-charge) for counter sunk wash basin, plateform /cooking plateform , steps, jambs,pillars, window cills, , shelves, urinal partition and like bedded and jointed with grey cement slurry @ 3.00Kg per Sqm and pointed with white cement with admixture of pigment to match the shade of granite stone with and including grinding and polishing , laid over with and including 15mm thick Rendering / screed bed in Cement Mortar 1:4 complete all as specified and directed by Engineer-in-Charge. |
| 25 | Supply & Fixing Rotational moulded polyethylene cylindrical vertical with closed top water storage tank triple layered WHITE COLOUR 500 Ltr capacity with connecting nipple, hoisted and fixed in position complete all as specified and directed by Engineer-in-Charge. |
| 26 | Supply and Fixing Ball valve high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for iron pipe of size 20 mm bore (minimum weight 20mm-210 gram) complete all as specified and as directed by Engineer-in- charge. |
| 27 | Supply and Fixing One-Piece Vitreous China Wash Down Water Closet (W.C.) of pedestal pattern, white/off-white colour, complete with soft-close/smooth-action plastic seat cover and valveless syphonic action flushing cistern of 10 Ltr capacity, including all integral fittings, fixing accessories, inlet and outlet connections, seals, fasteners and all necessary components required for proper installation and functioning, complete in all respects as specified and directed by the Engineer-in-Charge. |
| 28 | Supply and fixing Chromium Plated (CP) Brass Health Faucet (Hand Shower) complete with flexible stainless steel hose pipe of 1.0 m length ), wall hook/holder, brass check nut and all necessary fittings and accessories for connection to 15 mm nominal bore water supply pipe, complete in all respects as specified and directed by the Engineer-in-Charge. |
| 29 | Supply and Fixing PVC mirror cabinet, size 350x450mm, with shelves of best quality including fixing arrangements, complete all as specified and directed by Engineer-in-Charge. |
| 30 | Supply and fixing of PVC Mirror Cabinet of size 350 mm × 450 mm, made of best quality PVC, complete with mirror, internal storage shelves, door shutters, hinges, handles, fixing arrangements and all necessary hardware and accessories, complete in all respects as specified and directed by the Engineer-in-Charge. |
| 31 | Providing and fixing oval-shaped glass shelf assembly, 600 mm long, comprising 8 mm to 10 mm thick polished glass shelf with chromium-plated (CP) brass guard railing of double-rail design, complete with CP brass brackets, supports, fixing arrangements and all necessary fittings and accessories, complete in all respects as specified and directed by the Engineer-in-Charge. |
| 32 | Supply and Fixing of toilet roll holder with flap made of cast copper alloy, chromium plated, complete all as specified and directed by Engineer-in-Charge. |
| 33 | Supply and fixing 15 mm bore brass Chromium Plated mixer (ISI marked) for mixing hot and cold water , screwed down high pressure with long screwed shanks and fly nuts screwed for iron pipes complete all as specified and directed by Engineer-in-Charge. |
| 34 | Supply & Fixing 15mm bore PVC connection with PTMT nuts of 450mm long complete all as specified and directed by Engineer-in-Charge. |
| 35 | Supply & Fixing brass CP Centre hole Basin mixture 15 mm bore complete all as specified and directed by Engineer-in-Charge. |
| 36 | Supply & Fixing Brass Chromium Plated tubular towel rail, 20mm dia, D type, 60cm long between flanges and bracket complete all as specified and directed by Engineer-in-Charge. |
| 37 | Supply and fixing 600mm x 450mm size bevelled edge mirror selected quality 5mm thick glass mounted on 6mm thick commercial ply and fixed to wooden plugs with chromium plated brass screws and cup washers, including aluminium frame / beading alround made of aluminium channel, complete all as specified and directed by Engineer-in-Charge. |
| 38 | Supply and fixing 15mm bore bib tap cast copper alloy, chromium plated, fancy type (ISI marked) with crutch or butterfly handle with capstan head, screwed down, screwed for iron pipe or for brass ferrule complete all as specified & directed by Engineer-in-charge. |
| 39 | Supply and fixing 15 mm bore stop valve / angle valve, Chromium Plated, cast copper alloy (ISI marked) screwed down , high pressure with crutch or butterfly handle fancy type complete all as specified and directed by Engineer-in-Charge. |
| 40 | Supply and fixing chromium plated Grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified and directed by Engineer-in-Charge. |
| 41 | Supply and fixing PVC Nahani trap 75 mm dia with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B1 complete all as specified and directed by Engineer-in-Charge. |
| 42 | Supply and fixing 20mm bore galvanised iron medium grade pipe with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed by Engineer-in-Charge. |
| 43 | Supply and fixing 15mm bore galvanised iron medium grade pipe with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed by Engineer-in-Charge. |
| 44 | Supply and fixing 75 mm PVC SWR pipe single socketed , Type-B ISI Marked in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed by Engineer-in-Charge.Note: Earth work such as Excavation , returning filling and removal shall be measured and paid separetly under appropriate items of schedule 'A' BoQ. |
| 45 | Supply and fixing 110 mm PVC SWR pipe single socketed, Type -B in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed by Engineer-in-Charge.Note: Earth work such as Excavation , returning filling and removal shall be measured and paid separetly under appropriate items of schedule 'A' BoQ. |
| 46 | Supply and fixing PVC (SWR) Bends 75 mm bore in any radius ,Type -B (ISI Marked ) complete all as specified and directed by Engineer-in-Charge. |
| 47 | Supply and fixing PVC (SWR) Bends 110 mm bore in any radius , Type -B (ISI Marked ) complete all as specified and directed by Engineer-in-Charge. |
| 48 | Supply and fixing Stack clamps out of 50 mm by 5 mm flat ironand 16mm dia round iron stays, including bolts and nuts andsecuring ends of stays to wall or roof for bore of pipe 75mm complete all as specified and directed by Engineer-in-Charge. |
| 49 | Supply and fixing Stack clamps out of 50 mm by 5 mm flat ironand 16mm dia round iron stays, including bolts and nuts andsecuring ends of stays to wall or roof for bore of pipe 110mm complete all as specified and directed by Engineer-in-Charge. |
| 50 | Supply & Fixing Solid PVC door frame of size 50mm x 47mm made out of 5 mm single side prelam PVC sheet reinforced with MS square tube manufactured as per SSR Part-I specifications and drawings complete all as specified and directed by Engineer-in-Charge. |
| 51 | Supply & Fixing Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. complete all as specified and directed by Engineer-in-Charge. |
| 52 | Supply and fixing 150 mm aluminium handle cast type anodized complete all as specified and directed by Engineer-in-Charge. |
| 53 | Supply and Fixing 150mm long aluminium anodised barrel tower bolts of extruded section (ISI Marked ) complete all as specified and directed by Engineer-in-Charge. |
| 54 | Supply and fixing 100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed by Engineer-in-Charge. |
| 55 | Supply and fixing Powder coated anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long, hinges type B-21 100mm long (2 nos.) suitable handle incl sheet glass 4mm thick ordinary qlty complete all as specified and directed by Engineer-in-Charge. |
| 56 | Supply and fixing Mild steel as in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, Fe-410-W(Gde-E-250) quality-B, complete all as specified and directed by Engineer-in-Charge. |
| 57 | Material & Labour for preparation of newely steel surfaces of not exceeding 10 cm in width or girth or otherwise described , with and including applying two coat of syntheic enamal paint over with and including one coat of red oxide zinc chrome primer complete all as spefied and as directed by Engineer-in-Charge. |
| 58 | Material & Labour for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed by Engineer-in-Charge. |
| 59 | Material & Labour for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed by Engineer-in-Charge. |
| 60 | Material & Labour 4mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed in ceiling flat and sloping with nails to timber frame complete all as specified and directed by Engineer-in-Charge. |
| 61 | Supply and fixing 2nd class Hard wood in scantling clean sawn and fixed complete all as specified and directed by Engineer-in-Charge. |
| 62 | Material and Labour for 2nd class soft wood Plain fillets area exceeding 06 Sqcm and not exceeding 13 Sqcm. square, rectangular or triangular in section, clean sawn, secured with nails or brads. complete all as specified and directed by Engineer-in-Charge. |
| 63 | Material & Labour 2nd class soft wood plain fillets square/rectangular or triangular in section of sectional area exceeding 03 Sqcm but not exceeding 6 Sqcm splayed chamfered or rounded on one edge or face complete all as specified and directed by Engineer-in-Charge. |
| 64 | Material and labour for 75 mm thick PCC (1:3:6) Type C-2 using 40mm graded stone aggregate as in flooring, hard standing, plinth protection / path etc. finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge |
| 65 | Material and Labour for Construction of soakage well of size 1.80 mtr dia x 3.00mtr effective depth includingearth work such as excavation in any type of soil, returning filling and removal of earth work , foundation in PCC 1:3:6 Type-C-1 using 20mm graded stone aggregates, Honey combing Brick massony built with burnt clay old size bricks ,Top ring made with RCC M-25 Design Mix ,intercepting chamber and screen made with burnt clay old size brick with cement mortar 1:4, RCC M-25 Design Mix cover slab , 150mm bore salt glazed stoneware interconnecting pipes , filled with brick bats compete all as shown in drawing No.CESZ/TD-36/ST/20 SHEET 1/2 AND 2/2 DATED 22-02-2020 |
| 66 | Material & Labour 150mm reinforced concrete pipes, class NP2, laid and jointed with skeins of spun soaked in neat cement wash shall be inserted in the grooves at the ends of the pipes, the two adjoining pipes put against each other the collar is slipped over the joint covering equally both the pipes, more skiens of spun yarn soaked in cement wash shall be passed round the pipes and inserted in the joints by means of caulking tools after that cement mortar 1:2 slightly moistened shall be inserted in the joints finished in 45 degree slope complete Note:- After curing 7 days to the joints the sewage pipe shall be tested as per procedure laid down for water test complete all as specified and as directed by Engineer-in-Charge. |
| 67 | Material and labour for PCC (1:4: 8) type D-2 using 40 mm graded stone aggregates as in concrete bed for drain pipes of 150 mm bore, laid to required slope including packing under and haunching against the sides of pipes after they are laid and tested including form work complete all as specified and as directed by Engineer-in-charge. Note :- (i) Thickness of concrete bed below the barrel of pipe shall be 10 cm. (ii) Width of concrete bed shall be outer diameter of drain pipes (not of sockets / collar) plus 30cm.(iii) Excavation , earth work , returning filling shall be measured and paid seperately under appropriate items of schedule 'A' BoQ. |
| 68 | Material and labour for concealed Point wiring for modular fittings using approved colour coding as per IS (Red, Black and Green for single phase circuits), in new PVC conduit complete with and including 1.5 Sqmm two single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable 1100 volt grade ISI Marked , drawn through with and including new PVC rigid conduit 20mm dia ( heavy duty ) ISI marked with valid CML No.(IS-9537-1983 for conduits and IS:3419:1976 for conduit accessories) with all new fittings and all accessories i.e pipe bend pipe hook, elbow,junction box, pressed steel powder coated sunken box of suitable size (min 60mm deep, suitable length and 1.2mm thick ) and flush fixed with cement mortar 1:4 , Modular frame to cover all modular switches 5Amp/6Amp , modular socket outlet 5Amp/6Amp and modular fan regulator, for light / fan point / Exhaust fan controlled by one way switch 5Amp / 6Amp, top cover fixed with brass screws & cup washers, with and including one single core 1.5 Sqmm FRLSH PVC insulated multi strand copper conductor cable 1100 volt grade (ISI marked ) (as in green colour) as continues earth wire connected to earth dolly etc. with and including modular frame complete all as specified and as directed by Engineer-in- charge .Notes for serial item nos. 68.00 to 70.00 : (i) Modular switches one way 5 /6 Amp , Modular socket out lets 5 /6 Amp shall be measured and paid seperately under respective items of Schedule'A' BoQ.(ii) The rate of Modular frame is included in this item . Nothing shall be paid extra on this account.(ii) ) On RCC roof / ceiling PVC conduit shall be provided on surface with proper fixing clips as directed by Engineer-in- Charge.The rate of this element is included in this item and nothing shall be paid extra on this account. |
| 69 | All as per serial item No 68.00 of BoQ here-in-before but for one switch socket outlet point 5 Amp on independent board complete all as specified and directed by Engineer-in-charge. |
| 70 | All as per srl item No 68.00 of BoQ here-in-before but 4.00 Sqmm two single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable 1100 volt grade ISI Marked with and including one single core 4.00 Sqmm FRLSH PVC insulated multi strand copper conductor cable 1100 volt grade (ISI marked ) as continues earth wire connected to earth dolly etc for 3 pin socket outlet 15 Amps with complete all as specified and directed by Engineer-in-Charge. |
| 71 | Supply & Fixing Modular switch 1 way 6A,1 module (ISI Marked ) complete all as specified and directed by Engineer-in-Charge. |
| 72 | Supply & Fixing in Modular switch 1 way 16A,1 module (ISI Marked ) all complete all as specified and directed by Engineer-in-Charge. |
| 73 | Supply & Fixing in Modular socket, 6A - 2/3 pin combined 2 modules (ISI Marked ) complete all as specified and directed by Engineer-in-Charge. |
| 74 | Supply & Fixing in Modular socket 6/16A,2/3 pin, combined 2 module (ISI Marked) complete all as specified and directed by Engineer-in-Charge. |
| 75 | Supply and Fixing Decorative ultra slim linear LED 20 Watt 4 Feet Long lighting fixture with extruded aluminium heat sink,environment friendly, Energy efficient , ready to use pack with and including LED Tube complete , with inbuilt electronic driver, PCB, Connector block complete all as per manufactureres instructions with and including connecting up with theree copper flexible cable from ceiling rose to fitting including connectiong up and fixed on with and including two nos.square box of required size complete all as specified and directed by Engineer-in-charge. Notes:(a) Contractor has to furnish a replacement warranty of 02 years for LED light fittings complete including from the certifiy date of completion of CA. The product will be replaced free of cost in the following case :-(i) Manufacturing defects.(ii) Failure due to mechanical and electrical impact. (iii) Drop in lumen (or lux at 1 m) below 90% of clamied values of lumen(or lux at 1 m) of the LED /Luminaries. (b) All LED light must meet the provision laid down in IS - 16101, 16102 Part -I/II,16103 Part -I, 16104,16105,16106, 16108/2012 and 15885 Part -II / Section 13. (c) Scope of work shall include LED fittings walls/ceiling which includes needful T & P and required accessories etc if any, complete including making connection, testing etc complete. No extra payment is admissible on these account. |
| 76 | Supply and fixing Decorative ultra slim linear LED mirror light fiting 9/10 watt, 6000K, polycarbonate body and all other accessories fitting arrangements all other accessories fitting arrangements complete all as per manufacturer's instructions with and including electric connection connecting with using flexible copper wire twin core upto ceiling rose/connector complete all as specified and as directed by Engineer-in-Charge. Notes:(a) Contractor has to furnish a replacement warranty of 02 years for LED Light fittings complete including from the certifiy date of completion of CA. The product will be replaced free of cost in the following case :-(i) Manufacturing defects.(ii) Failure due to mechanical and electrical impact. (iii) Drop in lumen (or lux at 1 m) below 90% of clamied values of lumen(or lux at 1 m) of the LED /Luminaries. (b) All LED light must meet the provision laid down in IS - 16101, 16102 Part -I/II,16103 Part -I, 16104,16105,16106, 16108/2012 and 15885 Part -II / Section 13. (c) Scope of work shall include LED Light fittings walls/ceiling which includes needful T & P and required accessories etc if any, complete including making connection, testing etc complete. No extra payment is admissible on these account. |
| 77 | Supply & Fixing LED luminaire round/squre shape 15 watts 220 V AC surface/recessed type with hight efficiency PMMA diffuser soft glare free light complete with driver, holder & LED lamp suitable for foof ceiling/surface complete all as per manufacturer's instructions suitable for roof ceiling with and including connecting up with driver from ceiling rose with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge. Notes:-(a) Contractor has to furnish a replacement warranty of 02 years for LED Light fittings complete including from the certifiy date of completion of CA. The product will be replaced free of cost in the following case :-(i) Manufacturing defects.(ii) Failure due to mechanical and electrical impact. (iii) Drop in lumen (or lux at 1 m) below 90% of clamied values of lumen(or lux at 1 m) of the LED /Luminaries. (b) All LED light must meet the provision laid down in IS - 16101, 16102 Part -I/II,16103 Part -I, 16104,16105,16106, 16108/2012 and 15885 Part -II / Section 13. (c) Scope of work shall include LED Light fittings walls/ceiling which includes needful T & P and required accessories etc if any, complete including making connection, testing etc complete. No extra payment is admissible on these account. |
| 78 | Supply & Fixing LED Security street light fitting 35 Watt 230 V AC outdoor type, energy saving and environment friendly light fitting with electronic gear housed with high pressure die cast aluminum housing LED street light luminaires complete with IP66 protection including all accessories complete all as specified and directed by Engineer-in-Charge. Notes:-(a) Contractor has to furnish a replacement warranty of 02 years for LED Light fittings complete including from the certifiy date of completion of CA. The product will be replaced free of cost in the following case :-(i) Manufacturing defects.(ii) Failure due to mechanical and electrical impact. (iii) Drop in lumen (or lux at 1 m) below 90% of clamied values of lumen(or lux at 1 m) of the LED /Luminaries. (b) All LED light must meet the provision laid down in IS - 16101, 16102 Part -I/II,16103 Part -I, 16104,16105,16106, 16108/2012 and 15885 Part -II / Section 13. (c) Scope of work shall include LED Light fittings walls/ceiling which includes needful T & P and required accessories etc if any, complete including making connection, testing etc complete. No extra payment is admissible on these account. |
| 79 | Supply and fixing sheet metal enclousers made out of CRCA mild steel sheet , IP-43 protection, flush mounted with metal door, powder coated DB SPN 8 way 230 V AC with 200 Amp rated copper bus bar, Double Door dust and vermin proof suitable for incorporation of MCBs / MCCBs/ Isolators etc.conforming to IS/IEC-61439-2:2011, BS-5484 complete all as specified and directed by Engineer-in-charge. Notes: (i)MCBs / MCCBs/ Isolators shall be measured and paid seperately under appropriate items.(ii) The rate of 200 Amps copper bus bar is included in this item and nothing shall be paid extra on this account. |
| 80 | Supply and fixing MCB SP 6 to 32 Amps, 230 volts , AC supply , rupturing capacity not less than 10KA,' C' Curve ,ISI Marked, with and including necessary attachment , thimbles etc complete all as specified and directed by Engineer-in-charge. |
| 81 | Supply and fixing SPN 32 Amp rating 240 V, 10 KA 'C' curve miniature circuit breaker (MCB) complete all as specified and directed by Engineer-in-charge. Make: L&T/Legrand/ Havells |
| 82 | Supply and fixing ceiling rose surface bakelite 65mm x 50mm three terminals ISI Marked complete all as specified and directed by Engineer-in-Charge. |
| 83 | Material and Labour Cutting chases in brick wall, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed by Engineer-in-Charge. |
| 84 | Supply & Fixing Exhaust fan 300 mm sweep , made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m, ISI marked, including necessary work in wall/sheet, including connection cable, nut bolt and other fixing material complete all as specified and directed by Engineer-in-Charge. |
| 85 | Supply and Fixing water heater (Geyser) Auto restrat and safety measures type electrical operated 230/240 Volts 25 ltr capacity, BEE 5 star rated complete with all safety equipment and accessories such as safety valve, thermostat, plug top, etc. required for proper functionality & including electric/earth connections and carrying out grounting & complete installations with mounting bolts,nuts including testing after installation complete all as specified & directed by Engr-in- Charge. |
| 86 | Material and Labour for Sub main wiring with two single core of size 6.0 Sqmm FRLSH PVC insulated unsheathed with multistranded copper conductor cable 1100 volts grade ISI Marked including cuttting, chasing and grouting , with and including non metallic rigid PVC conduit medium quality of size 25 mm dia conforming to 3537 Part-I ISI marked including all fitting such as Tee, Elbow, bend etc drawn in and including one single core of size 6.0 Sqmm FRLSH PVC insulated unsheathed with multistranded copper conductor cable 1100 volts grade ISI Marked as in contineous earth conductor cable connected to earth dolly complete all as specified and as directed by Engineer-in- charge. (Colour code phase-Red, Neutral-black and Earth as Green) complete all as specified and as directed by Engineer-in- charge. Notes:-(a) Cost of PVC conduit , conduit accessories and earth wire included in sub main wiring. (b) Three single core 6.0 Sqmm FRLSH PVC insulated unsheathed with multistranded copper conductor cable 1100 volts grade ISI Marked with and including non metallic rigid PVC conduit of size 25 mm ISI Marked dia shall be measured as one length. |
| 87 | Supply and laying or fixing or laid in trenches/ ducts/ through pipes/ in floors / under roads/ hard standing /along poles and testing LT cable XLPE, PVC insulated screened, bedded, galvanised steel strip or wire armourd cable (heavy duty) 1100 volt grade with aluminium conductor having cross sectional area 70 Sqmm x 4.00 core conforming to IS-7098 (Part-I -1988) complete all as specified and as directed by Engineer-in-Charge. (Excavation and earth work, sand cushioning & GI pipe shall be measured and paid for separately) |
| 88 | Supply and laying or fixing or laid in trenches/ ducts/ through pipes/ in floors / under roads/ hard standing /along poles and testing LT cable XLPE, PVC insulated screened, bedded, galvanised steel strip or wire armourd cable (heavy duty) 1100 volt grade with aluminium conductor having cross sectional area 10 Sqmm x 2.00 core conforming to IS-7098 (Part-I -1988) complete all as specified and as directed by Engineer-in-Charge. (Excavation and earth work, sand cushioning & GI pipe shall be measured and paid for separately) |
| 89 | Supply, installing, testing and commissioning of CPRI approved LT distribution panel Indoor type of suitable size (length x width x hight), weather/vermin proof, made out of 2.15mm thick CRCA sheet duly powder coated, mounted on angle iron frame 65mm x 65mm x 6mm of hight 45 cm from PCC bedding, factory assembled compartmentalized construction, free standing type, including 3 phase and neutral 400 amps current carrying capacity copper bus bar with epoxy insulated coating with colour code and insulated support, cable galleries inter connecting bus bar connection/linkage complete and conforming to IS 8623 and IP 54 class of protection as per IS 2147 complete, including making connection of cables of incoming and outgoing with thimble/lugs, and mountig the panel on ground/floor with PCC(1:3:6) bedding upto a height of 30 cm above ground level with and including the accessories described as under :(i) MCCB 160 Amp 4 pole 25 KA - 01 No. (ii) MCCB 100 Amp 4 pole 25 KA 01 No.(iii) MCCB 63 Amp 4 pole 25 KA -02 Nos.(iv) Amp meter with CTs - 1 No.(v)Volt meter - 1 No .(vi) Indicators( Y / B / R)- set of three |
| 90 | Material and Labour for earthing complete with galvanised steel earth plate electrode 600mm x 600mm x 6 mm thick burried directly in ground to depth of pit not less than 2.25 m below normal ground level with top edge of the plate not less than 1.5 m below normal ground level surrounded from all sides by 15 cm thick packed layer of charcoal / coal dust and common salt filling in alternate layers and connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of GI or steel including GI protection pipe 15mm dia light grade upto the extent of 7.5 metre and connecting to earthing test point, main switch board including GI pipe 20 mm dia medium grade for watering, MS funnel and bringing out the watering pipe upto 30 cm above the normal ground level plugged at top including all fitting including PCC earth pit with PCC 1:2:4 type B-1 using 20mm graded stone aggregate and RCC pit cover including necessary earthwork and excavation in any type of soil complete all as specified as shown in electrical plate No 3 of SSR Part-I and testing on completion. Note:- (i) Earth continuity of GI wire 4 mm including protection pipe up to 7.5 mtrs from earth electrode will be included in unit rate, complete all as specified and directed. (ii) The rate of earth work in soft/loose soil i.e. excavation, returing filling and removal, form work is included in this item and nothing shall be paid extra on this account. (iii) PCC chamber shall be constructed at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner. (iv) The earth testing arrangement should be done by the contractor as per direction of Engineer-in-charge. |
| 91 | Supply and laying Galvanized iron pipe medium grade 20mm bore laid in trench complete all as specified and directed by Engineer-in-Charge. Note: Earth work such as excavation, returning filling and removal shall be measured and paid seperately under appropriate items of Schedule 'A' BoQ. |
| 92 | Supply and laying Galvanized iron pipe medium grade 25mm bore laid in trench complete all as specified and directed by Engineer-in-Charge. Note: Earth work such as excavation, returning filling and removal shall be measured and paid seperately under appropriate items of Schedule 'A' BoQ. |
| 93 | Supply and fixing 20mm bore Gun metal, globe or gate valve (ISI marked), brass cast copper alloy, with iron wheel head, screwed both ends suitable for iron pipes complete all as specified and as directed by Engineer-in-charge. |
| 94 | Supply and fixing 25mm bore Gun metal, globe or gate valve (ISI marked), brass cast copper alloy, with iron wheel head, screwed both ends suitable for iron pipes complete all as specified and as directed by Engineer-in-charge. |
| 95 | Material and Labour for Cutting of existing CI / GI pipe line of 20mm to 50mm bore and inserting with and including NEW TEE of appropriate size and taping new connection with all accessories complete all as specified and as directed by Engineer-in-charge. Note: The rate of supply and fixing of NEW TEE of appropriate size is included in this item.Hence bidder shall be quoted his rates accordingly and nothing shall be paid extra on this account. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jun 27, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 20, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 13 daysJul 23, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 16 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender