|
| 1 | M&L for servicing of DG Set 180 KVA to 200 KVA of any Make ,checking entire system as per manufacturer's catalogue such as checking all parts for serviceability, taking down defective parts such as fuel filter assembly, by pass filter assembly, lube oil filter assembly, air cleaner assembly lube oil hose flexible pipe, hose turbo etc including replacement the same with same size, make and capacity of parts Such as Fuel filter, Lube oil filter, Air filter, coolant and Engine oil ,hose pipe,Diesel filter with gasket etc and draining out the old used burnt engine oil from the oil sump and cleaning oil sump with suitable cleaning solution such as petrol and diesel or any other cleaning solution and refilling new engine oil required grade up to required level and including checking of AMF control panel, tightening of loose connections and testing to DG Set to the entire satisfaction of the Engineer-in-ChargeMake -Greaves Cotton Note : (i) Engine oil shall be measured and paid for separately under successive items here-in-after. However, labour charge are deemed to be included in item rate above. (ii) Servicing shall be carried out by authorised dealer of manufacturer.(iii) Minimum 6 months gap/200 Hrs of run whichever is earlier shall be considered for next service. (iv) Repair Guarantee for replaced parts/servicing of DG Set shall be for six month from the date of service. |
| 2 | All as per item No 1.00 above but DG set of capacity 75 KVA. |
| 3 | All as per item No 1.00 above but DG set of capacity 62.5 KVA. |
| 4 | All as per item No 1.00 above but DG set of capacity 15 KVA. |
| 5 | S & F for Fan belt set suitable as per existing for 15 kVA to 200 kVA DG Set of any type any make complete all as specified and directed. |
| 6 | S& F for New dehydrated Engine oil as required grades suitable as per existing for 15 kVA to 200 kVA DG Set of any type any make complete all as specified and directed. Note :- Engine oil will be suppied in manufacturer sealed barrel. |
| 7 | Taking down of radiator from DG set (15 kVA to 200 kVA DG) of any type any make carefully cleaning of tubes and fins complete with the help of proper cleaning agent and wire brush soldering of tubes and fins at required places testing and refilling complete all as specified and directed. |
| 8 | Taking down of defective water pump from DG set (15 kVA to 200 kVA DG) of any type any make repair the same by water pump repair kit removing of leakage refitting after testing complete all as specified and directed. |
| 9 | Repair and Replacement of water pump body assembly suitable for 15 kVA to 200 kVA DG Set of any type any make complete all as specified and directed. |
| 10 | Repair and replacement of self starter motor and charging alternator 24 volts complete set incl dismantling and taking down old unser from DG set suitable for 15 kVA to 200 kVA DG set of any make any type complete all as specified and directed. |
| 11 | Repair and replacement of self starter motor and charging alternator 12 volts complete set incl dismantling and taking down old unser from DG set suitable for 15 kVA to 200 kVA DG set of any make any type complete all as specified and directed. |
| 12 | S&F in replacement of solenoid switch suitable for existing DG including all necessary arrangement for kirloskar CUMMINS Gen set of capacity 15 to 200 KVA complete all as specified and directed. |
| 13 | Supply only distilled water of best quality in 05 litrs sealed gallon packing complete all as specified and directed. |
| 14 | M&L for carrying out repair of complete DG set by taking each and every parts carefully carrying out necessary repairs of Engine in workshop including machining work of parts like of pump nozzle, turbo charger (reconditioning and servicing), head of DG set, cleaning and repairing of radiator, oil pump and refilling of coolant , engine oil as per requirement and guidelines of respective OEMs and replacement of following spares suitable for diesel engine (prime mover) of DG set of capacity 200 KVA including testing complete all as specified and directed by Engineer-in-Charge.(a) Piston ring (l) Diesel filter(b) Main Bearing (m) Mashroom taper(c) Piston (n) Diesel pipe complete set(d) Packing Kit (o) Air filter(e) 'O' ring (p) Water pump(f) Liner (q) Fly wheel ring gear(g) Exhaust valve(h) Inlet valve(j) Head gasket kit(k) CR BearingNote : Transporting Cahrges of Stn to Workshop and back to stn deemed to be included in the rate quoted . |
| 15 | Opening the pressure filter 1200mm dia Make-Pentair installed at swimming pool equipment room removing the old filter media, removing all the scaling deposited on the surface area of filter assembly by using wire brush and cleaning the filter with HCL, refilling new filter media ( as per existing type)of various silica grade as required at site, re-assembling the filter assembly and apply one coat of good quality paint on the outer surface area of the filter assembly and testing for leakage for proper functioning and testing with the following specifications is maintained (a) Flow rate 125 m³/ Hr (Each), (b) Vessel dia-2000mm, (c) Filteration velocity 40m³/hr/m², (d) Working pressure 2.5 Kg/Cm² complete all as specified and directed. |
| 16 | M&L for replacement of unservicable Butterfly valve type IS 5312 flanged ends 150 mm dia complete all as specified and directed. |
| 17 | Material & Labour for repairs to existing LT panel board, including painting with one coat of synthetic enameled paint to steel surfaces including preparation after scraping, filling, cavities etc, including replacement of damaged bus bar, lugs, copper wire etc complete all as specified and directed. |
| 18 | Supply and fixing MCCBs 415 volts, 4 pole, 36 KA, 250 Amps capacity complete all as specified and directed. |
| 19 | S & F Volt Meter 0 to 500 Volts digital square type 4” complete all as specified and directed. |
| 20 | S & F Ammeter 0 to 200 Amps digital Square type 4” complete all as specified and directed. |
| 21 | S & F Selector switch for Volt meter /Ampmeter complete all as specified and directed. |
| 22 | S & F Indicating Lamp set of three (Red , Yellow & Blue) complete all as specified and directed. |
| 23 | M&L for disconnecting/ dismantling (electrically & mechanically) mono-block pump, 3 Phase, 440 Volts AC, 15 HP capacity and transporting to workshop , opening the pump motor, cleaning the pump, greasing to bearing/bushes, replace the gland rope, gland nut bolts, opening motor, varnishing to stator winding with class I varnish, heating, baking the same, greasing to motor bearing, cleaning the rotor and re assembling the same, and two coats of painting to the outer cover or yoke with existing colour, brought back at site, refixing at its original location with proper alignment and testing complete all as specified and as directed. |
| 24 | M&L for Disconnecting / taking down / dismantling Solar flat plate collector of 100/125 LPD capacity for servcing , cleaning and repairing, brazing of tubes complete and reassembling the same after repair complete all as specified and directed. |
| 25 | M & L for De-scaling, cleaning of hot water and cold water tanks incl heat collecting units with heat absorbing sheet etc of solar heating system of capacity 500 LPD complete all as specified and directed. |
| 26 | M & L for De-scaling, cleaning of hot water and cold water tanks incl heat collecting units with heat absorbing sheet etc of solar heating system of capacity 1000 LPD complete all as specified and directed. |
| 27 | Supply and fixing in replacement electric Heating element 3 KW( for solar water heater) with thermostat for electrical Back up complete all as specified and directed. |
| 28 | Supply and Install SS Hot Water Tank of Capacity 500 Ltrs ( suitable for existing) double wall insulated with PUF Insulation machine injected inner shell SS 316 and Outer Shell SS 304 Stucco Aluminium alloy coated coloured steel complete on roof tops at aheight of 7 ft incl connection of inlet and outlet water connections complete all as specified and directed. |
| 29 | All as per item No 28.00 above but capacity of 1000 ltrs. |
| 30 | M&L for hot water pipe duly insulated with glass wool and aluminium cladding 20 mm bore including taking down complete all as specified and directed. |
| 31 | M&L for hot water pipe duly insulated with glass wool and aluminium cladding 25 mm bore including taking down complete all as specified and directed. |
| 32 | M&L for replacement of Gunmetal gate valve with iron wheel head screwed both ends for iron pipe and fixed 25 mm dia including taking down complete all as specified and directed. |
| 33 | M&L for replacement of Gunmetal gate valve with iron wheel head screwed both ends for iron pipe and fixed 20mm dia including taking down complete all as specified and directed. |
| 34 | M&L for replacement of unservicable parts of solar water heater complete with servicable parts and making it servicable complete testing and commsioning and brazing of tanks for arrresting leakages complete all as specified and directed.Note : Parts will be measured here after as supply only. |
| 35 | S&F following items for solar water heater 500/1000 LPD complete all as specified and directed. |
| 36 | All as per item No 35.00 above Absorber Plate made of copper sheet, laser or ultrasonically welded to copper tubes ( Solar flat plate collector as per existing type) with FlangesL-1860 W-1240 H-100, weight 35-42 kg working pressure 490 KPA . |
| 37 | All as per item No 35.00 above Absorber Plate made of copper sheet, laser or ultrasonically welded to copper tubes ( Solar flat plate collector as per existing type) with Flanges L-1860 W-1240 H-100, weight 35-42 kg working pressure 1300 Kps. |
| 38 | M&L for Single pane 3.2 mm tempered low iron glass collector as per existing size and type complete all as specified and directed. |
| 39 | Supply & install 500 Ltr Cold water Tank of material SS-304( as per existing type) with Manhole & Stand complete all as specified and directed. |
| 40 | Supply & install 1000 Ltr Cold water Tank of material SS-304 ( as per existing type) with Manhole & Stand complete all as specified and directed. |
| 41 | Supply & install Makeup Tank for heat exchanger of 5 Liter with ball cock complete all as specified and directed. |
| 42 | Supply & install Back Plact Collector complete all as specified and directed. Please Enable Macros to View BoQ information |
| 43 | Supply & install Back Plact Collector complete all as specified and directed. Please Enable Macros to View BoQ information |
