|
| 1 | Demolition of brick work built in cement mortar of any description complete all as specified and as directed. |
| 2 | M&L for brickwork (old size) with Sub class ‘B’ bricks, straight or curved on plan exc. 6m mean radius, built in cement mortar (1:6) complete all as specified and as directed. |
| 3 | All as per Serial item No. 2 here-in-before but except bricks, using old serviceable brick as retrieved from demolition.Note : Old serviceable bricks obtained from Serial item No. 1 above shall re-used. |
| 4 | Taking down cement plaster on brick or stone or concrete surfaces of walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and as directed. |
| 5 | M&L for rendering 15mm thick on fair face of brick works or concrete surfaces of walls with CM (1:4), finishing the surface even and smooth without using extra cement complete all as specified and as directed. |
| 6 | M&L for preparation of new plastered surfaces of walls and applying two coats of cement base paint over and including one coat of alkali resistance primer complete all as specified and as directed. |
| 7 | Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed. |
| 8 | M&L for plain cement concrete (1:2:4) type B-0 (using 12.50mm graded stone aggregate) used as in benching and coping including necessary formwork complete all as specified and as directed. |
| 9 | M&L for brickwork with sub class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in CM (1:4) complete all as specified and as directed. |
| 10 | M&L for dismantling posts or struts (wood, steel or RCC) any section, including taking out embedded portion and making good to disturbed ground surfaces complete all as specified and as directed. |
| 11 | M&L for plain cement concrete (1:3:6) type C-2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete, etc. complete all as specified and directed. |
| 12 | S&F hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing, etc. wind ties for roof including securing bolts posts and struts in fencing of size 65x65x6mm including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc. and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed. |
| 13 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed. |
| 14 | S&F 11mm to 15mm dia of shank mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and onehexagonal or square nut, but length of bolt exc. 5cm but n. exc. 10cm complete all as specified and as directed. |
| 15 | Excavating in post holes (or similar holes) each n. exc. 0.5cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering and removing surplus soil to a distance not exc. 50m and making good surface as in soft/loose soil complete all as specified and as directed. |
| 16 | M&L for preparation of new steel and iron surfaces of any description over 10cm width or girth not otherwise described for and applying two coats of synthetic enamel paint over and including one coat of red oxide primer complete all as specified and as directed. |
| 17 | M&L for mild steel TMT bar 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends binding with and including mild steel wire (annealed) not less then 0.9mm dia or securing with clips, quality, complete all as specified and as directed. |
| 18 | All as per Serial item No. 17 here-in-before but 5mm dia and over upto and including 10mm dia used in stirrups, spacers, binders, etc. |
| 19 | Dismantaling old chain link fencing of any description complete all as specified and as directed. |
| 20 | M&L for providing and fixing chain link fabric fencing made of GI wire of 3mm dia of required width in mesh size 50x50mm including strengthening with 2mm dia 6 Nos wire and nuts, bolts and washers as required complete all as specified and as directed. Note : The work shall be carried out as per IS 4996. |
| 21 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off the premises complete all as specified and as directed. |
| 22 | M&L for endura rustic tiles of size 300x300x10mm thick as in floor, etc., set and jointed in neat cement slurry and pointed in white or colured cement to match over and including 20mm thick screed bedding layer in cement mortar (1:6) complete all as specified and as directed. |
| 23 | M&L for chequered cement concrete tiles of size 20cmx20cmx25mm thick, set, jointed and pointed in neat cement slurry as in floors with white cement and pigment to match as in floors over and including 20mm thick screed bedding layer in cement mortar (1:4) complete all as specified and as directed. |
| 24 | M&L for plain cement concrete (1:2:4) type B-2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and as directed. |
| 25 | M&L for 25mm (or required thickness) sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed. |
| 26 | M&L for machine pressed precast concrete interlocking paver block of any shape and size confirming to IS : 15658-2006 of 60mm thickness, M-35 Grade complete all as specified and as directed |
| 27 | S&F including laying of crossed spiral concertina coil 600mm dia made up of 2.50mm HTGS spring core wire having tensile strength of 1670N/sqmm and punched tape of 0.50mm thick and 13mm wide after crimming. Punched tape shall be of hot dipped galvanised min 20 micron and having medium barbs of 24mm width @ 35mm centre to centre. Each concertina coil shall be of minimum 50 turns and 5 clips in two turns i.e. 125 clips per coil complete all as specified and as directed. Note : Weight of coil shall be 7 kg to be streched upto 3.25 RM i.e. 2.15 Kg/Rm. |
| 28 | S&F galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. complete all specified and as directed.Note : Each line wire to be measured.NOTE : The contract sum shall be derived by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ. Please Enable Macros to View BoQ information |
