Tender For Comprehensive Maintenance Of Otm And Md Accn At Mil Stn Jalipa Under Ge (A) Barmer
Tender Value
38 Lakhs
Estimated cost
Bid Submission
18 Jul 2026
16 days left
EMD
76000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Barmer → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Comprehensive Maintenance Of Otm And Md Accn At Mil Stn Jalipa Under Ge (A) Barmer
BOQ
| Sl. No. | Item Description |
| 1 | Taking down chowkats or frames (without taking of shutters from the frames) area not exceeding 1.5 Sqm each including fair finish of existing plaster surface complete all as specified and as directed . |
| 2 | Taking down chowkats or frames (without taking of shutters from the frames) area exceeding 1.5 Sqm but not exceeding 4 Sqm each fair finish of existing plaster surface complete all as specified and as directed . |
| 3 | Taking down shutters of any description exc 1 sqm and n exc 2 sqm each complete all as specified and as directed. |
| 4 | Taking down shutters of any description exc 1 Sqm and n exc 2 Sqm each and refixing in same opening after cutting by chishel or hand saw, peeling by plane, fixing/ re-placing of hinges, repairing etc including all nales screws, pieces, small let in for making good where hinges, etc. have been removed from chowkhats or frames, shutters, etc. including painting or oiling to match, if required complete all as specified and as directed.(Note : Hinges shall be measured and paid separately) |
| 5 | Repairs existing aluminium door/ window shutter including frame with completely/partially taking down door shutter and tightening of all screws, replacing including provision of unservicable hinge, handle, lock, aluminium plate & floor door stopper and complete all as specified and as directed by the Engineer-in-Charge. |
| 6 | S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing. The door frame shall be tied to the wall using 75/100mm long MS screw as directed . |
| 7 | S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails. M S tube for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS fram welded/sealed to the stile and rails with suitable PVC sheet beading and jointed together with solvent cement. |
| 8 | S&F for 150mm size Aluminium anodizes barrel tower bolts of extruded section complete all as specified and as directed. |
| 9 | S&F for pressed steel frames of size 125X60mm of 1.25mm thick for doors with one or more rebates including necessary fixing lugs. hinges, lock strike plate,etc complete all as specified and as directed. |
| 10 | S&F for pressed steel frames of size 105X60mm of 1.25mm thick for doors with one or more rebates including necessary fixing lugs. hinges, lock strike plate,etc., complete all as specified and as directed. |
| 11 | M&L for PCC 1:3:6 type C-0 using 12.5mm graded aggregate in hollow portion of pressed steel door/window frames including compaction and curing complete all as specified and directed. |
| 12 | S&F for 35mm thick flush shutter, solid core construction, with particle board core and plywood face panels, commercial type on both faces including teak wood beading 6mm thick all around complete all as specified and as directed. |
| 13 | S&F for 35mm thick 2nd class HW plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply .The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and as directed. |
| 14 | M&L for 35mm thick factory made 2nd class HW glazed and skelton shutter and open rebated and prepared to receive glass, gauge etc (without sash bars), edges or framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR Part-I Section 8 Clause 8.24 (a) complete all as specified and as directed. |
| 15 | S&F for stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire stapples and fix with wooden bidding complete all as specified and as directed. |
| 16 | S&F for 100mm size butt hinges, medium weight, cold rolled mild steel, complete all as specified and as directed. |
| 17 | S&F for mild steel ordinary rat tail rod pattern spring 250mm size including roller & roller plate and incl welding complete all as specified and as directed. |
| 18 | S&F for 200mm size Aluminium anodizes barrel tower bolts of extruded section complete all as specified and as directed. |
| 19 | S&F for 200mm size aluminium anodized handle complete all as specified and as directed. |
| 20 | M&L for 250mm size aluminium alloy anodized sliding door bolts with Hasp and staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed. |
| 21 | S&F for 140mm length aluminium floor door stoppers double legged with hard drawn steel spring fitted in floor complete all as specified and as directed. |
| 22 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 100X65 mm comprising of virgin PVC polymer of K value 58-60(Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additive(maximum toxicity index of 12 for 100 gms)fabricated with miter joints after applying PVC solvent cement and screwed with fullbody threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressivestrength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).complete as per direction of engr-in-charge. |
| 23 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately) |
| 24 | S&F of factory made single extruded WPC(Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) |
| 25 | S&F of stainless steel butt hinges of size 100 mm, with necessary stainless steel screws, complete all as specified and directed. |
| 26 | S&F of 200 mm long Stainless Steel Handle, made of SS Grade 304, finished with satin/matt polish, including all necessary screws, rawl plugs, drilling holes in wood/steel/aluminium/wpc surfaces, and fixing complete in all respects as specified and directed. |
| 27 | S&F of 200 mm long Stainless Steel Tower Bolt , made of SS Grade 304, with necessary screws, finished with satin/matt polish, including drilling holes in wpc/wooden/steel/aluminium frames/shutters and fixing complete in all respects as specified and directed. |
| 28 | S&F of 250 mm long Stainless Steel sliding tower bolt with hasp and staple (bolt type) and fixing clips of sheet, made of SS Grade 304, with necessary screws, finished with satin/matt polish, including drilling holes in wpc/wooden/steel/aluminium frames/shutters and fixing complete in all respects as specified and directed. |
| 29 | M&L for preparation of New or previously untreated wood and wood based surfaces of any description, not otherwise, described, over 10cm width or girth and painting with two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed. |
| 30 | M&L for preparation of New or previously untreated steel or iron surfaces of any description over 10cm in girth or width and painting with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. |
| 31 | S&F for powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified |
| 32 | S&F of powder coated aluminium door shutters,aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, ruber neoprene packing,handles 2 Nos in each door, hinges,anodised aluminum snap beading screws etc. complete all as specified. |
| 33 | S&F for powder coated aluminium window and ventilator shutters, side hung and sliding type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified |
| 34 | M&L for powder coated aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin-charge. |
| 35 | S & F for Stainless steel wire cloth of 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixedd with tinned tacks or stainless steel wire staples or with wooden beads, stainless steel screws and nuts bolts etc complete fixed as in repair complete all as specified. |
| 36 | M&L for 4.8mm thick sheet glass, ordinary quality and fixed with glazing clips, rubber packing in square in n exc 0.5 sq.m in each pane in each pane complete all as specified and as directed. |
| 37 | S & F of mortice lock brass 4 levers vertical type without handle, size 100mm complete all as specified and as directed. all as specified and directed approved by accepting officer |
| 38 | S&F of aluminium( Extruded section) body door closer hydraulically regulated , designation No. 3 universal type , suitable for door shutterof 851 to 1000mm in width complete all as specified and directed. |
| 39 | S&F of double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box , main body with stainless steel cover, govering pivot made of brass, other parts made of mild steel heavy duty including taking down of onld one and fixed . complete all as specified and directed. |
| 40 | S&F of aluminium partition (0.8-1.2 kg/rm weight) work using extruded aluminium sections of approved make (such as Jindal/Hindalco or equivalent) for frame, vertical and horizontal members including cutting, fabrication, assembling and fixing in position with necessary screws, cleats, angle brackets etc., complete.The aluminium sections shall be powder coated finish of minimum 1.2–1.5 mm thickness, including providing and fixing 5 mm thick clear glass / prelaminated particle board / gypsum board panels as specified, fixed with EPDM rubber gasket, glazing clips, beading etc.The work includes providing and fixing all fittings such as handles, locks, tower bolts, door closer (if required), including sealing joints with silicone sealant, finishing edges properly, and making good the surrounding surfaces complete in all respects including taking down of old partition as specified and directed. |
| 41 | S&F for toughened (tempered) safety glass of approved make conforming to IS 2553 (Part-1), of 10 mm / 12 mm thickness as specified, including cutting to required size, machine polished/arrised edges, necessary cut-outs for fittings, and fixing in position in aluminium channels / SS patch fittings with EPDM rubber gaskets, setting blocks, structural silicone sealant, anchor fasteners, etc.,SS handle (450–600 mm length, 25–32 mm dia) including taking down of old toughened glass complete all as specified and directed. |
| 42 | S&F in replacement aluminium Mortice lock vertcle type size 100 mm 4 lever type complete all as specified and directed. |
| 43 | Dismantling wall and ceiling boarding of any description, thickness including cover fillets complete al as specified and directed. |
| 44 | S&F in replacement Prelaminated particle board of 18/19mm thick, interior grade prelaminated one side with decorative choice lamination & other side balancing white lamination with teak wood leaping on exterior face, fixed with screws as in cupboard shutters of bed room, kitchen and internal shelves complete all as specified and as directed. |
| 45 | Dismantiling wrought iron or mild steel work of any description not otherwise provided for etc comoplete all as specified. |
| 46 | M&L for Mild Steel (MS) frame for cupboard fabricated from MS angle/box section of approved size including cutting, welding, grinding, making true to line and level, fixing in position with holdfasts/fasteners, including necessary lugs, cleats, screws, nuts & bolts, complete complete all as specified and directed. |
| 47 | S&F for 30mm width of flaps (When open) continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and directed. |
| 48 | S&F for 75 mm size aluminium anodized handle complete all as specified and as directed. |
| 49 | S&F for magnetic cathes and striking plate for cup board etc complete all as specified and dirrected. |
| 50 | S&F for 100mm Hasp and staple aluminiumn anodised wire type including bolt to hinge plate and fixed with screws complete all as specified and directed. |
| 51 | S&F in replacement 100mm Hasp and staple, aluminiumn anodised wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and directed. |
| 52 | S&F in replacement 150 mm aluminium anodised barrel tower bolts, of extruded section all as specified and directed |
| 53 | S&F in replacement 200 mm aluminium anodised barrel tower bolts, of extruded section all as specified and directed |
| 54 | S&F in replacement 250mm aluminum anodised sliding door bolts, with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast alluminium alloy complete all as specified and directed. |
| 55 | S&F in replacement SS butt hinges of 100 mm size medium weight fixed to existing frame complete all as specified and directed |
| 56 | S&F in replacement mild steel butt hinges of 100 mm size medium weight cold rolled by welding to existing frame complete all as specified and directed |
| 57 | S&F in replacement mild steel ordinary rat tail rod pattern spring 250mm size including roller & roller plate and incl welding complete all as specified and as directed. |
| 58 | S&F in replacement 150mm size aluminium anodized handle complete all as specified and as directed. |
| 59 | S&F in replacement 200mm size aluminium anodized handle complete all as specified and as directed. |
| 60 | S&F in replacement 140 mm over all length floor door stopper, bearing ISI mark, of aluminium alloy body and tongue, anodised with hard drawn steel spring, complete all as specified and as directed. |
| 61 | S&F in replacement chromium plated 35mm self close cup hinges for kitchen cabinets,cupboard etc. fixing with ss screws complete all as specified and directed |
| 62 | S&F in replacement 100mm SS handles for kitchen cabinets,cupboard,doors etc complete all as specified and directed |
| 63 | S&F in replacement 75mm SS handles for kitchen cabinets,cupboard,doors etc complete all as specified and directed |
| 64 | S&F in replacement 25mm dia stainless steel curtain rod with fancy type fixing brackets, stops, rollers,finials etc. complete all as specified and directed by Engr-in-charge.(Note : Entire work will be done/ executed in patches of any qty and any size all as specified by Engr-in-charge) |
| 65 | Hacking out old broken glass [any thickness, size, quality or description] from metal frames including punching or drilling out old glazing pins / spring clips complete all as specified and as directed. |
| 66 | S&F for sheet glass 3mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sq.m in each pane complete all as specified and as directed. |
| 67 | S&F for sheet glass 3mm thick, ordinary quality and glazing with oil putty in squares exceeding 0.5 Sq.m in each pane complete all as specified and as directed. |
| 68 | S&F for 3mm thick figured glass, pin head type and glazing with putty in square not exceeding 0.50 Sqm in each pane complete all as specified and as directed. |
| 69 | S&F for 3mm thick figured glass, pin head type and glazing with putty in square exceeding 0.50 Sqm in each pane complete all as specified and as directed. |
| 70 | S&F in replacement double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box , main body with stainless steel cover, govering pivot made of brass, other parts made of mild steel heavy duty including taking down of onld one and fixed . complete all as specified and directed. |
| 71 | S&F in replacement aluminium( Extruded section) body door closer hydraulically regulated , designation No. 3 universal type , suitable for door shutterof 851 to 1000mm in width complete all as specified and directed. |
| 72 | M&L for running welding in repairs for metal thick not exc. 6mm including cleaning and preparing the surfaces to be welded together, holding the members in true position while welding & bevelling of edges as required, complete all as specified and as directed. |
| 73 | M&L for welding in repairs n. exc 2.5cm in length Thickness of metal to be welded N exc 6mm complete all as specified and as directed. |
| 74 | Demolition of cement concrete un -reinforced in ground floors and pavings n.exc 15cm thickness complete all as specified. |
| 75 | M&L for 25mm thick cement concrete type B-1, 1:2:4 (20mm grade aggregate) as in levelling coarse in flooring finished even and fair under floor finishes. |
| 76 | M&L for Glazed ceramic glossy finish tiles coloured in vertical surface 450X300X7mm in any pattern of light & dark/highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and jointed in cement slurry over & including 10 mm thick rendering in cement mortar (1:3) and pointed in white cement with pigment to match the colour of tiles including dismantling of old tiles complete all as specified. |
| 77 | M&L for Non Skid ceramic tiles colour tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4 for laying floor finishes including demolition of old tiles complete all as specified. Note : Work will be in patches or in bulk |
| 78 | M & L for Single charge, stainfree, vitrified tiles, Premium (1st) quality straight edge, coloured tiles 600 X 600 mm and 9-10 mm thick, as in floors etc. in any pattern of light coloured tiles as in approved shade, set & jointed in neat cement including and over 15mm th screed bed in CM (1:4) and pointed in white coloured cement to match, in floors etc.including demolition of old tiles complete all as specified. |
| 79 | All as per item 78.00 here-in-above but as in skirting over cement mortar backing plaster in CM1:3 10mm thick including dismantling of old tiles complete all as specified and directed. |
| 80 | Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles in all as specified |
| 81 | M & L for Providing precast cement concrete solid building blocks or slabs 10cm thick (with plain or interlocking joints as directed) in PCC 1:3:6 type C1 using 20mmgarded aggregate and setting in mortar 1:4 complete, in walls complete all as specified and directed. |
| 82 | M & L for precast cement concrete solid block masonry exc 10cm in width and setting in CM 1:4 type C1, 1:3:6 all as specified. |
| 83 | Taking down cement or cement lime plaster, any description on brick or stone/block walls etc including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off the premises and leaving the work clear for plastering complete all as specified and as directed. |
| 84 | M&L for Ready mix plaster 15mm thick on fair faces of brick work or stone surfaces or rcc member finished even and smooth without using extra cement complete all as specified and directed. |
| 85 | M&L for Ready mix plaster 15mm thick on other than fair faces of brick work or stone surfaces or rcc member , finished even and smooth without using extra cement complete all as specified and directed. |
| 86 | M & L for Ready mix plaster 5 mm thick on ceiling surfaces finished even and smooth without using extra cement, complete, all as specified and directed. |
| 87 | M&L for 10mm Ready mix plaster for dubbing coat for the additional thickness( of ant thickness) is provided as floating/setting coat for stone masonary wall plaster complete all as specified and directed by Engineer-in-Charge. |
| 88 | M&L for Chipping of 50mm average thickness unsound/weak concrete material from slabs, beams, columns, footings etc. and plaster with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts complete all as per direction of Engineer-In-Charge |
| 89 | M&L for Cleaning & applying rust remover on in two coats over rusted reinforcement surface of RCC members and providing anti corrosive coating with two component epoxy based zinc rich primer/Rust passivation Inhibitor coat at the rate of 2-3 sq. mtr/ltr not less than 50 microns dft to reinforcement surface as per manufacturer’s instructions including all machinery, tools tackles and clearing of debris.(Note : Entire Exposed Surface of RCC members after chipping shall be measured and paid.) |
| 90 | M&L for providing 25 to 30mm Micro concrete M-50 (Minimum grade) with CICO MICROCONCRETE at the rate of 25kg per 0.0125 m3 with 20% properly graded 5mm to 10mm silt free aggregate as per manufacturer instructions and mixing concrete with mechanically electrically operated mixer machine including proper props and structural steel support for any height if required and curing compound on new surface etc all as specified and directed.Make: CICO MICROCONCRETE of CICO Technologies Ltd or equivalent in Fosroc/STP/BASF. |
| 91 | M&L for Epoxy Bonding Agent suitable for bonding new to old concrete, bricks and steel components, bricks, tiles etc after the prepration of old concrete/RCC surface by cleaning and removing of dust, dirt, loose particles, laitance etc by wire brushing, scrapping and washing with water complete all as per manufacturer's instructions.(Make: Dr. Fixit or Equivalent) |
| 92 | M&L for preparing new plastered or unplastered surfaces of walls, and applying two coats of distemper oil emulsion over a coat of interior wall primer complete all as specified and directed. |
| 93 | M&L for preparing new plastered or unplastered surfaces of walls, and applying two coats of white wash complete all as specified and directed. |
| 94 | M&L for preparing new plastered or unplastered surfaces of ceiling, and applying three coats of white wash complete all as specified and directed. |
| 95 | M&L for preparation of new plastered surfaces of external walls/RCC surfaces/soffits of chajjas/roof projection/cantilivers/balcony etc including cornices and applying two coat of cement base paint @ 5sq.m/kg/1 coat over a one coat of of external primer by using following brands of cement base paint complete all as specified & as directed by engr-in-charge. Make of cement paint:- Snowcem Plus (Snowcem paints) |
| 96 | M&L for preparing old plastered or unplastered surfaces of walls including filling of cracks/holes by crack filler, removing unnecessary nails and applying one coat of oil bound distemper/ emulsion complete all as specified and directed. |
| 97 | M&L for preparing old plastered or unplastered surfaces of walls including filling of cracks/holes by crack filler, removing unnecessary nails and applying one coat of white wash complete all as specified and directed. |
| 98 | M&L for preparing old plastered or unplastered surfaces of ceiling, including filling of cracks/holes by crack filler, removing unnecessary nails and applying one coat of white wash complete all as specified and directed. |
| 99 | M&L for special treatment to floor/wall sunken portion with demolition of PCC with plaster of entire sunken area (bottom & sides upto skirting level) including removal of demolished material exc 250m and n exc 500m, prepration of surface by cleaning to remove loose particles, dust, latance etc, replacement of floor trap, and applying 10mm thick plaster in CM (1:3) with WPC liquid Conplast 421,and applying one coat each of Nitoproof 100 priming coat @1Ltr/5Sqm, after the priming coat applying Nitoproof 120 on plastered surfaces @1Ltr/2.5Sqm, filling the sunken floor with PCC (1:5:10) using brick bat and WPC Conplast - 421, rendering again 20mm thick in CM (1:4) mixed with WPC Conplast - 421, area of floor for kitchen/WHB trap upto 0.25Sqm complete all as specified and as directed. |
| 100 | M&L for special treatment to floor/wall sunken portion with demolition of PCC with plaster of entire sunken area (bottom & sides upto skirting level) including removal of demolished material exc 250m and n exc 500m, prepration of surface by cleaning to remove loose particles, dust, latance etc, replacement of floor trap, and applying 10mm thick plaster in CM (1:3) with WPC liquid Conplast 421,and applying one coat each of Nitoproof 100 priming coat @1Ltr/5Sqm, after the priming coat applying Nitoproof 120 on plastered surfaces @1Ltr/2.5Sqm, filling the sunken floor with PCC (1:5:10) using brick bat and WPC Conplast - 421, rendering again 20mm thick in CM (1:4) mixed with WPC Conplast - 421, complete all as specified and as directed. |
| 101 | Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing, etc. measured separately) exc 250 Ltrs and n exc 500 Ltrs capacity complete all as specified. |
| 102 | Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing, etc. measured separately) exc 500 Ltrs and n exc 1000 Ltrs capacity complete all as specified. |
| 103 | Cleaning & removing all scale and dirt etc from tank and from mouth of circulating pipe etc exc 250 Ltrs and n exc 500 Ltrs capacity complete all as specified. |
| 104 | Cleaning & removing all scale and dirt etc from tank and from mouth of circulating pipe etc exc 500 Ltrs and n exc 1000 Ltrs capacity complete all as specified. |
| 105 | Dismantling of water tanks (RCC hume/PVC) Exc 250 and n exc 500 ltrs including disconnecting all connections etc. complete for following capacity of tanks complete all as specified and directed. |
| 106 | Dismantling of water tanks (RCC hume/PVC) Exc 500 and n exc 1000 ltrs including disconnecting all connections etc. complete for following capacity of tanks complete all a specified and directed. |
| 107 | S&F for new rotational moulded polythylene water storage tank 500 ltrs(cylindrical/vertical with closte top) hoisted and fixed in position all as specified in SSR Part-I including providing and fixing ball brass valve high pressure with polythene float and fly nut, 20mm bore and tank nipple complete all as specified and directed. |
| 108 | S&F for new rotational moulded polythylene water storage tank 1000 ltrs (cylindrical/vertical with closte top) hoisted and fixed in position all as specified in SSR Part-I including providing and fixing ball brass valve high pressure with polythene float and fly nut, 20mm bore and tank nipple completeall as specified and directed. |
| 109 | Cutting chases, holes in Brick walls, Stone walls, concrete block or slab walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth all as specified and as directed. |
| 110 | S&F in replacement 20mm (OD) CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches/ walls and ceiling fixed in repairs all as specified and as directed. |
| 111 | S&F in replacement 25mm (OD) CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches/ walls and ceiling fixed in repairs all as specified and as directed. |
| 112 | S&F for 20mm bore GI tubing medium grade with all fittings and fixed complete to walls and ceiling or laid in floors including dismantling of old unsv pipe complete all as specified and as directed. |
| 113 | S&F in replacement 20mm bore Ball valves highpressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms) |
| 114 | S&F in replacement 25mm bore Ball valves highpressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms) |
| 115 | S&F in replacement 15mm bore CP fancy type stop valves/angle cock, cast copper alloy, screwed both ends for iron pipe or for union complete all as specified and as directed. |
| 116 | S&F in replacement two way 15mm bore CP fancy type angle cock, cast copper alloy, screwed both ends for iron pipe or for union complete all as specified and as directed. |
| 117 | S&F in replacement 15mm bore stop valves, angle cock, cast copper alloy, chromium plated with long shank and cup (concealed type) complete all as specified and as directed. |
| 118 | S&F in replacement 15mm bore Bib taps CP fancy type, cast copper, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. |
| 119 | S&F in replacement 15mm bore two way Bib taps (for health faucet/jet spray) fancy type, chromium plated, cast copper ally with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. |
| 120 | S&F in replacement 15mm bore dia pipe CP wall mixer for mixing (HOT/COLD) water, with wall cap/band of CP Brass, screwed down, screwd for iron pipes 15mm bore complete all as specified and directed. |
| 121 | S&F in replacement 15mm bore centre hole basin mixer fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' and `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed. |
| 122 | S&F in replacement 15mm bore Brass CP sink mixer fancy type with swinging casted spout (wall mounted type) for kitchen sink screwed down for iron pipe and fixed complete all as specified and directed. |
| 123 | S&F in replacement 15mm bore pillar taps, cast copper alloy with capstan heads, chromium plated,fancy type screwed down high pressure with or without lettered “HOT” or “COLD” with long screwed shanks and fly nuts complete all as specified and as directed. |
| 124 | S&F in replacement Brass chromium plated shower rose 125mm size complete all as specified and as directed. |
| 125 | S&F in replacement Jet Spray (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.00 metre long flexible tube including making connections and fixed in position complete in all respect complete all as specified and directed. |
| 126 | S&F in replacement Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect complete all as specified and as directed. |
| 127 | S&F in replacement brass chromium plated Tubular towel rail 20mm dia, D type, 60cm long between flanges complete all as specified and as directed. |
| 128 | S&F in replacement Towel Ring of PTMT dia 200-215 mm fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) complete all as specified. |
| 129 | S&F in replacement chromium plated brass towel ring of heavy quality,ring dia 175-200 mm,min 8mm rod thickness approved make, complete with CP brass brackets, CP brass screws, rawl plugs and all necessary fittings and fixtures fixed firmly to wall complete all as specified and directed by Engineer-in-Charge |
| 130 | S&F in replacement SS soap dish, approximate size 100x75 mm, fixed to plugs with chromium plated brass screws complete all as specified and directed. |
| 131 | S&F in replacement Toilet paper holder with flat recessed type stainless steel fixed to walls with chromium plated (CP) brass screws complete all as specified and as directed. |
| 132 | S&F in replacement PVC valveless flushing cistern, low level white with inlet ball valve float and handle including brackets complete fixed capacity of flush 10 ltrs complete all as specified and as directed. |
| 133 | S&F in replacement 15mm bore, 450mm long, PVC connections with brass unions internally threaded both ends complete fixed to iron pipe at both ends as fixed in repairs complete all as specified and as directed.. |
| 134 | S&F in replacement 15mm bore, 600mm long, PVC connections with brass unions internally threaded both ends complete fixed to iron pipe at both ends as fixed in repairs complete all as specified and as directed.. |
| 135 | S&F in replacement 15mm bore PTMT Bib taps standard any colour screwed down for iron pipe and fixed minimum weight 90 gm complete all as specified and directed. Make: Prayag & equivalent. |
| 136 | S&F in replacement 15mm bore pillar taps fancy type (long body) cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed. |
| 137 | S&F in replacement of 32mm Waste coupling of PTMT (half or full threaded) .(Minimum weight 32mm-45gms/40mm-60 gms.for kitchen sink complete all as specified and directed. |
| 138 | S&F in replacement Grating 100mm made out of round stainless steel complete all as specified and directed. |
| 139 | S&F in replacement 32 to 40mm dia PVC waste pipe for WHB/sink/Urinal complete all as specified and as directed. |
| 140 | S&F in replacement 450mmx600mm bevelled edge mirror of selected quality glass, mounted on 6mm thick PVC sheet and fixed to wooden plugs with chromium plated brass screws and cup washers, complete all as specified and as directed. |
| 141 | S&F in replacement sheet glass corner wall mounted shelf assembly consisting of 5.50 mm thick sheet glass 220mmX220mm size with chromium plated bracket guard and railing 50mm high complete all as specified and as directed. |
| 142 | S&F in replacement sheet glass shelf aasembly consisting of 5.50 mm thick sheet glass shelf 120 mm wide with chromium plated bracket guard and railing of 600 mm long complete all as specified and as directed. |
| 143 | S&F in replacement vitreous china wash down water closet pan (pedestal pattern), white including P or S trap, connection to drain (or outgoing pipe) and to flushing pipe 32mm PVC with and including plastic water closet seat, white closed pattern with flat bottom, cover and mild steel hinges device,flushing cistern of 10ltr capacity complete all as specified. |
| 144 | S&F in replacement vitreous china squatting Pan “Orissa” Pattern, of size 580mm x 440mm white with integral foot rests and trap,including flushing cistern and flush pipe, including trap and provn of cement concrete bedding complete as fixed complete all as specified. |
| 145 | S&F in replacement wash hand basins, vitreous china,of size 550x400mm (flat back, or angle back type) including cutting for and pinning in ends of brackets or erecting stand inclusive of fixing of supply and 32mm PVC waste pipe and waste coupling etc complete all as specified and as directed. |
| 146 | S&F in replacement plastic water closet seat for pedestal/semi pedestal closet pan, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified. |
| 147 | S&F in replacement sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe,overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. |
| 148 | S&F in replacement stainless steel kitchen rack made of 0.63 mm thick stainless steel sheet of size 900 mm x 750 mm x 250 mm fixed to wall with screws complete all as specified and directed. |
| 149 | S&F in replacement chromium plated brass sprindle suitable for 15 mm concelled type stop cock / angle cock / Pillar tap/ Bib tap complete all as specified and directed. |
| 150 | S&F in replacement mirror of approved quality and size made from 5 mm thick superior quality float glass mirror with silver backing and protective paint coating on rear side, fixed to wall with CP brass screws and washers over approved backing surface fixed in aluminium/wooden/PVC frame complete all as specified and as directed. |
| 151 | S&F in replacement one piece European Water Closet (EWC) made of white vitreous china, including integral flush tank, dual flush system (3/6 litre), soft-close seat cover, S/P trap, all fittings, and fixing complete in all respects, including connection with soil pipe and testing complete all as specified and directed. |
| 152 | S&F in replacement 550x450 vitreous china wash basin with pedestal,including waste coupling, chromium plated brass long body sink mixer, hot and cold 450-600mm PVC braided connection pipes with fittings ,waste pipe, all necessary brackets, screws, nuts, washers ,angle cock and fixing accessories complete in all respects as per direction of Engineer-in-Charge |
| 153 | S&F in replacement 20 mm gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipe and complete all as specified and directed. |
| 154 | S&F in replacement 75mm bore PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and as directed. |
| 155 | S&F in replacement PVC (SWR) bend any radius 110mm complete all as specified and directed. |
| 156 | S&F in replacement PVC (SWR) bend any radius 75mm complete all as specified and directed. |
| 157 | S&F in replacement PVC (SWR) bend any radius 110mm provided with access door complete all as specified and directed. |
| 158 | S&F in replacement PVC (SWR) bend any radius 75mm provided with access door complete all as specified and directed. |
| 159 | S&F in replacement 110 mm bore PVC [SWR] Junction single [single \\"T\\"] equal or unequal with access door complete all as specified and as directed. |
| 160 | S&F in replacement 75 mm bore PVC [SWR] Junction single [single \\"T\\"] equal or unequal with access door complete all as specified and as directed. |
| 161 | S&F in replacement 110mm bore of PVC (SWR) pipes single socketed in any length with rubber ring joints laid on wall complete all as specified and as directed. |
| 162 | S&F in replacement 75mm bore of PVC (SWR) pipes single socketed in any length with rubber ring joints laid on wall complete all as specified and as directed. |
| 163 | Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for |
| 164 | Demolition of stone slabs and tiles laid, bedded and pointed in any mortar of any description or thickness in floors, aprons etc complete all as specified and as as directed. |
| 165 | M & L for Granite of black / green / imperial red (colour as approved by Accepting Officer) of any type machine cut as in shelves/steps/counter tops, 18-20 mm thick, including hole set and jointed in cement slurry over & including screed of 15 mm thick / rendering in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab or with suitable adhesive for fixing on unpolished kota stone slabs and including rubbing, cutting and mirror type polishing and bull nose on exposed sides complete all as specified .Note : Single piece should be used in steps/cills/jambs/shelves or equivalent as approved by accepting officer . |
| 166 | M&L for Kota stone slab 18-20mm thick (in single piece as vertical support and horizointal base for granite top) laid over in cooking platform,counter top, jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete complete all as specified and as directed. |
| 167 | S&F in replacement of Factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite ) Plain Board of required size with stainless steel ISI marked fittings as 75mm/100mm ss fancy handles (01 No in each shutter ), with 35mm stainless Steel auto cup hinges (if shutter height 600mm-2 hinges,600-900mm-3 hinges,900-1200mm-4 hinges) with necessary full body threaded star headed counter sunk SS Screws comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural Fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with density not less than 650 kg/cbm , having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N (Edge ), Minimum Compressive Strength of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof, Fire Retardant and fixing .All as per direction of Engineer -In-Charge. For WC/Bathroom/Toilet/Kitchen/Balcony Doors & Cabinets. |
| 168 | S&F in replacement 6 mm thick WPC (Wood Polymer Composite) board of approved make and shade as back panel of cupboards/cabinets, fixed in grooves or with suitable screws, including cutting, edge finishing, necessary supports, fixtures and fasteners,all specifications will be match above item no. 167 complete all as specified and directed. |
| 169 | S & F in repair Perforated Cutlery Basket with 4mm dia 100 % stainless steel, non - magnatic, multilayer chrome plated, argon welded, double sealed ball bearing mechanism capable of holding plates, cup, saucers, bowls and dongas with 420x485x100 mm of carcass complete all as specified & directed by Engineer -in -Charge. Make : Prod code No. 6133 of Godrej or equivalent make in Hettich/Lifetime |
| 170 | S & F in repair Thali-Plate Basket baskets with 4mm dia 100 % stainless steel, non - magnatic, multilayer chrome plated, argon welded, double sealed ball bearing mechanism capable of holding plates, cup, saucers, bowls and dongas with 420x485x200 mm of carcass complete all as specified & directed by Engineer -in -Charge. Make : Prod code No. 6138 of Godrej or equivalent make in Hettich/Lifetime |
| 171 | S & F in repair Cup and saucer Basket baskets with 4mm dia 100 % stainless steel, non - magnatic, multilayer chrome plated, argon welded, double sealed ball bearing mechanism capable of holding plates, cup, saucers, bowls and dongas with 420x485x200 mm of carcass complete all as specified & directed by Engineer -in -Charge. Make : Prod code No. 6158 of Godrej or equivalent make in Hettich/Lifetime |
| 172 | M&L for 6mm Non asbestos fibre cement building boards(600mmx600mm) fixed or laid/inserted to GI/Aluminium framework with screws including dismantling of old unsv board complete all as specified and directed. |
| 173 | Dismantling of Wall and ceiling boards (fibre,pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including fillets. |
| 174 | S&F for Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves andscrews at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section(not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including supporting hangers complete all as specified and directed. |
| 175 | M&L for 6mm Non asbestos fibre cement building boards(600mmx600mm) fixed or laid/inserted to GI/Aluminium framework with screws (frame work for ceiling shall be measured and paid seperately) complete all as specified and directed. |
| 176 | S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing |
| 177 | S&F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and sample approved by engr-in-charge. |
| 178 | S&F in replacement Venetian blinds screen fabric with 5% openness factor roller type for windows of colour/shade as approved by Ac cepting Officer complete fixed in position inclusive S&F of all accessories and hardwares for fixing and operation, all as recommended by manufacturer, all as specified incl taking down old curtain rods of any type complete. |
| 179 | S&F in replacement stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire stapples of any type of windows and doors i.e. wooden, steel or aluminium including opening and refixing of frame, shutter or shutter elements if required and new wooden beads in wooden doors, complete all as specified and as directed. and directed. |
| 180 | Taking, down copper / aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulatros, socket, light fitting, boxes, CP, sheets etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc all as directed. |
| 181 | Disconnecting / dismantling of old existing unserviceable DB's/ metal sockets any way 240/415 volts with their unserviceable burnt MCB's all as directed |
| 182 | Taking down unserviceable PVC insulated / sheathed sub main wiring aluminium conductor cable of size upto 10 Sqmm on wooden batten/ PVC conduits, complete ith battens/ conduits and remove from site and make good disturbed surfaces of wall as directed. Please Enable Macros to View BoQ information |
| 183 | Taking down unserviceable PVC insulated / sheathed sub main wiring aluminium conductor cable of size upto 10 Sqmm on wooden batten/ PVC conduits, complete ith battens/ conduits and remove from site and make good disturbed surfaces of wall as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jun 27, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 18, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 16 daysJul 20, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 18 days