Tender For Construction Of New Canteen Block At Govt. Degree College Nagrota, Jammu.
Tender Value
60.09 Lakhs
Estimated cost
Bid Submission
03 Jul 2026
1 days left
EMD
1.20 Lakhs
Bank guarantee accepted
Document Fee
1500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jammu → Jammu and Kashmir
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of New Canteen Block At Govt. Degree College Nagrota, Jammu.
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: All kinds of soil : |
| 2 | Providing and laying of hand packed stone soling (size 150mm - 230mm) before layng of mud compacted consolidated rammed filling the voids in carriage upto site of work all head load complete Job. |
| 3 | P/L cement concrete 1:4:8 mix using 40mm size crushed stone aggs. |
| 4 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. Complete. |
| 5 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding thecost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improveworkability without impairing strength and durability as per direction of Engineer-incharge. All work up to plinth level |
| 6 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding thecost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improveworkability without impairing strength and durability as per direction of Engineer-incharge. All work above plinth level |
| 7 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 8 | P/L cement concrete 1:3:6 mix using 20mm size crushed stone agg.ete |
| 9 | Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4 (1 cement:2 coarse sand: 4 graded stone aggregate 20 mm nominal size) and curing complete |
| 10 | Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in :Cement mortar 1:6 ( 1 cement : 6 coarse sand). |
| 11 | Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level |
| 12 | 6mm Cement plaster of mix: 1 : 4 ( 1 cement : 4 fine sand) |
| 13 | 12mm Cement plaster of mix: 1 : 4 ( 1 cement : 4 fine sand) |
| 14 | 15mm Cement plaster of mix: 1 : 6 ( 1 cement : 4 fine sand) |
| 15 | Centering and shuttering including strutting, propping etc. and removal of form work for: |
| 16 | Foundations, footings, bases for columns |
| 17 | Suspended floors, roofs, landings, balconies and access platforms. |
| 18 | Column, pillar , piers, |
| 19 | LINTEL Beam, plinth Beam, Girder etc. |
| 20 | Stairs (excluding landings) except spiral staircases. |
| 21 | Providing and applying white cement based putty of specified thickness of approved brand and manufacture |
| 22 | Finishing with Deluxe multi surface paint system for interiors andexteriors using primer as per manufacturers’ specifications: Two or more coats applied @ 1.25 liter/10Sqm over andincluding one coat of special primer applied @ 0.75liter /10Sqm |
| 23 | Finishing walls with acrylic smooth exterior paint of required shade on New work (Two or more coats applied @ 1.67 liter/10Sqm over and including priming coat of exterior primer applied @ 2.20kg/10Sqm) |
| 24 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): Second class deodar wood |
| 25 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. 2nd Second class deodar wood |
| 26 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area ofopening for panel inserts excluding portion inside grooves or rebates to bemeasured). Panelling for panelled or panelled and glazed shutters 25 mm to 40mm thick. |
| 27 | With fly proof stainless steel 304 wire guage with 0.5mm dia wire and 1.4 mm wide aparture. |
| 28 | Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge : Second class teak wood 35 mm thick |
| 29 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. With ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws .35 MM THICK |
| 30 | Apply PRIMING COAT : With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ liter |
| 31 | Finishing with Deluxe multi surface paint system for interiors and exteriors using primer as per manufacturers’ specifications: Painting wood work with deluxe multi surface paint of required shade. Two or more coats applied @ 0.90litre/10sqm over an under coat of primer applied @ 0.75litre/10sqm of approved brand and manufacture |
| 32 | Brass Fittings Providing and fixing bright finished brass butt hinges with necessary screws etc. complete : 100x85x5.5 mm (heavy type) |
| 33 | Providing and fixing bright finished brass 100 mm mortice latch with one dead bolt and a pair of lever handles of approved quality with necessary screws etc. complete. |
| 34 | Providing and fixing bright finished brass door earls approved quality with necessary screws etc. complete. |
| 35 | Providing and fixing bright finished brass handles with screws etc. complete : 125 mm |
| 36 | Providing and fixing bright finished brass hard drawn hooks and eyes 250 mm |
| 37 | Providing and fixing bright finished brass handles with screws etc. complete : 75 mm |
| 38 | Providing and fixing bright finished brass handles with screws etc. complete : |
| 39 | Providing and fixing ISI marked oxidized M.S. tower bolt black finish, (Barrel type) with necessary screws etc complete. |
| 40 | Providing and Fixng Bright Finished Brass hanging type floor door stopper with necessary screws, etc. Complete. |
| 41 | Providing and fixing aluminum die cast body tubular type universal hydraulic door closer (having brand logo with IS: 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete : |
| 42 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete SIZE 600X600MM. |
| 43 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622(thickness to be specified by the manufacturer), of approved make, in all colours, shadesexcept burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 44 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 11.68.1 Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. |
| 45 | Providing and fixing 10 mm thick acid and/or alkali resistant tilesI n dado/skirting on 12mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) |
| 46 | Providing and fixing M.S. grills of required pattern in frames of windows etc.with M.S. flats, square or round bars etc including priming coat with approvedsteel primer all complete. 9.48.2 Fixed to openings / wooden frames with rawl plugs screws etc. |
| 47 | Apply PRIMING COAT : With ready mixed red oxide Zinc Chromate primer of approved brand and manufacture on steel work (second coat) |
| 48 | Finishing with Deluxe multi surface paint system for interiors and exteriors using primer as per manufacturers’ specifications: Painting steel work with deluxe multi surface paint ofrequired shade to give an even shade. Two or more coats applied @ 0.90litre/10Sqm over an under coat of primer applied @ 0.80litre/10Sqm of approved brand and manufacture |
| 49 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 50 | Supplying and filling in plinth with fine sand under floors including, watering, ramming, consolidating and dressing complete. |
| 51 | Providing and fixing on wall face un-plasticized Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.(i) Single socketed pipes 110 mm diametre |
| 52 | Providing and fixing on wall face un-plasticized - PVC moulded fittings/accessories for un plasticized Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansionCoupler 110 mm. |
| 53 | Providing and fixing on wall face un-plasticized - PVC moulded fittings/accessories for un plasticized Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion Bend 87.5° 110 mm bend |
| 54 | Providing and fixing to the inlet mouth of rain water pipe PTMT (anEngineering Thermoplastic) grating square (Slit) 150 mm square with a height of 8 mm and weighing not less than 100 gms. |
| 55 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-White Vitreous China Wash basin size 550x400 mm with a 15 mmCP Brass single hole basin mixer |
| 56 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings |
| 57 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040mm bowl depth 250mm |
| 58 | ADD FOR Providing 32 mm dia. C.P. brass trap. ALL WASHBASIN |
| 59 | Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.ALL WASHBASIN |
| 60 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with brackets of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.ALL WASHBASIN |
| 61 | Providing and fixing PTMT shelf 440 mm long, 124 mm width and 36 mm height of approved quality and colour, weighing not less than 300 gms. ALL WASHBASIN |
| 62 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete:40 mm dia washbasin and sink |
| 63 | Providing and fixing in position 25 mm diameter mosquito proof coupling of approved municipal design.ALL WASHBASIN |
| 64 | Providing and fixing uplasticized PVC connection pipe with brass unions 45 cm length 20 mm nominal bore washbasin and sink |
| 65 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 66 | Providing and fixing 600x120x5mm glass shelf with edges round off supported on anodized aluminum angle frame with C.P. brass brackets and guard. |
| 67 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete: |
| 68 | Providing and fixing brass bib cock of approved quality.20mm nominal dia pipes.20mm nominal dia pipes. |
| 69 | Providing and fixing brass STOP cock of approved quality.15mm nominal dia pipes. |
| 70 | Providing and fixing brass STOP cock of approved quality.20mm nominal |
| 71 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 20 mm nominal bore |
| 72 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 25 mm nominal bore |
| 73 | Providing and fixing gun metal non-return valve of approved quality (screwed end) Horizontal 25 mm nominal bore |
| 74 | Providing and fixing gun metal non-return valve of approved quality (screwed end) Horizontal 32 mm nominal bore |
| 75 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with a minimum distance of 37 mm from wall face with concealed fittings arrangements of approved quality and colour, weighing not less than 88 gms. |
| 76 | CPVC PIPES AND FITTINGS Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge. |
| 77 | Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc.15mm nominal dia pipes. |
| 78 | Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc.25mm nominal outer dia pipes. |
| 79 | External work including trenching, refilling etc.32mm nominal outer dia pipes. |
| 80 | Providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to ISI: 12701, colour of opaque white or as approved by Engineer-in-charge. The rate includes making necessary holes for inlet, outlet & over flow pipes. The base support i/c fittings & fixtures for tank shall be paid separately. |
| 81 | Providing and fixing 150X100MM size square mouth S.W Gully trap P type , with C.I grating brick masonary chamber and water tight C.I cover frame 300x300mm size inside the wt of cover& frame to be not less then 7.2 kgs |
| 82 | Constructing of concrete main hole with C.I cover including all cost of material size 900x900x450mm |
| 83 | Making soak pit 2.5 m diameter 3.0 meter deep with 45x45 cm dry brick honey comb shaft with common burnt clay (non modular) bricks of class designation 7.5 bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. |
| 84 | Providing Fixing and installing the internal concealed type gas pipeline for kitchen of specified dia with proper specification of fire and heat resistant material of high grade with all necessary components of piping . Gas cylinder must fix away from Burner. |
| 85 | Providing and laying water proofing treatment in sunken portion ofWCs, bathroom etc., by applying cement slurry mixed with waterproofing cement compound consisting of applying water proofing chemical mixed with cement slurry on inside walls of sump tank complete item as per ssr 2022 |
| 86 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mmangle iron and 3mm M.S. gusset plates at the junctions and corners, allnecessary fittings complete, including applying a priming coat of approved steel primer. |
| 87 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand :6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth and curing complete |
| 88 | Providing & fixing storage type water cooler ,40 L with plain & cold water facility of the following capacity, I.S.I marked, stainless steel front panel, C.P brass push cock, inlet float valve with all plumbing and electrical accessories, inlet, outlet, overflow and PVC drain out connection to F.D complete as required (Blue Star or equivalent).Cooling capacity 50 Ltrs./hr |
| 89 | Carriage of material by Mechanical Transport including loading/unloading and stacking at site complete. |
| 90 | Sand average lead of 10.00 Kms |
| 91 | Stone aggregate Below 40 mm size for average lead of 10.00 Kms. |
| 92 | Brick for average lead of 40.00 Kms. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jun 27, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 03, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 1 dayJul 04, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 2 days