Tender For Shifting, Installation, Testing And Commissioning Of 3000Gphx200 Head Meter Hc Pumpset Alongwith Allied Works And Design, Fabrication, Providing, Installation, Testing And Commissioning Of 70 Ere Lt Control Panel Alongwith Allied Works At
Tender Value
5 Lakhs
Estimated cost
Bid Submission
03 Jul 2026
2 days left
EMD
10000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Udhampur → Jammu and Kashmir
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Shifting, Installation, Testing And Commissioning Of 3000Gphx200 Head Meter Hc Pumpset Alongwith Allied Works And Design, Fabrication, Providing, Installation, Testing And Commissioning Of 70 Ere Lt Control Panel Alongwith Allied Works At Pumping Station Pinger (Old)
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling/Disassembling of old HC pumping unit of capacity 3000 GPH x200 meter head and motor by way of disconnecting of all incoming electrical connections, decoupling of pump and motor, unfastening from base frame and shifting and stacking at a safer place. Dismantling / extraction / cutting of wornout suction and delivery bends, pipes and connected old unserviceable sluice valves, reflux valves and subsequently plugging of open end of delivery pipe line near manifold by Fabrication/providing & fitting of blind flange of suitable thickness with rubber gasket, nuts, bolts etc. Removal of base frame from the damaged concrete block by dismantling /breaking/ of old existing RCC block by way of deploying skilled and unskilled labour by using pneumatic hammer, high carbon chisels and other tools and tackles etc. up to a point where removal of bed plate from foundation bolt can take place completely. Reconstructing of RCC foundation block in the new pump room by way of deploying skilled and unskilled labour. Laying of bed concrete of 1:1.5:3 mix using 20 percent boulders aggregate, (laying of RCC of 1:1.5:3 mix) including supplying/fixing of form work / shuttering, aggregates, sand and cement, reinforcement steel 10 or 12mm complete with cutting, bending, placing in position and binding, angle iron for supporting/alignment of base-frame, welding, placing of foundation bolts with base frame and making proper alignment of base frame horizontally as well as longitudinally, deployment of vibrator, mixer, welding set, tools and tackles etc. Job further includes carriage/shifting of pump motor set from the stacking place from old pump room to the new pump room and then placing them on the base frame by manual labour and other tools and tackles, Leveling of pump motor set on the base frame by using laminated sheet, strips and coupling thereof. Testing and commissioning of pump motor set on full load. Job further includes providing/carriage/fitting of suction / delivery pipes for suction and delivery network and inter connection for R/main and suction inlet and fitting of new 80mm dia pipes as per site requirement, maximum upto 24 meters. the job further involves providing/fitting of sluice valve (CI) alongwith CS sluice valve 80mm dia suction side and sluice valve 80mm with check valve (CS) (by pass arrangement) delivery side. The job includes providing and fitting of flanges, nut bolt, rubber sheet, welding works or any other work required for successful running of the pumping machinery at site.The job includes earthwork in bulk excavation for the foundation block on each of the four sides of the block up to the depth of about 3’ feet so as to form a size of 6’x3’x3’. Dumping of excavated material outside the pump room at a distance of 100 meters approximately. Providing and fabrication of 4 no. foundation bolts of suitable diameter and 2’ long by threading them at one end and making of anchor to other end. Job includes providing of 3.5 core 95 mm2 Al cable 50 meter in length with proper thimbling and insulation, 300 Ampere bus bar, 100 Ampere MCCB, cost of material and machinery, transportation charges, manual carriage charges, skilled and unskilled labour charges, hire charges of tools and tackles etc. (Complete job) |
| 2 | Design, fabrication, providing, installation, testing and commissioning of 70 ampere LT control panel cum fault analyzer cum auto starter. The job involves providing and fitting of MCCB of suitable rating acting as on / off system as well as tripping system in case of fault. The job involves fabrication of auto starter for motor alongwith providing and fitting of power contractors in required numbers having suitable rating conforming to ISI standards. The system should be provided with controller cum fault analyzer of appropriate rating. The complete system should be enclosed in MS steel enclosure box of suitable dimensions. The enclosure should be finished with powder coated painting from inside as well as from outer surface of approved colour. Providing / laying of copper conductors of proper rating alongwith insulation material as per site requirement.METERING: The enclosure should be front shutter mounted with key locking system having glass window, digital electronic voltmeter, ampere meter are to be provided along with the required current transformer and selector switches. The internal wiring should be done with flexible PVC LT cable with proper thimbling at each end.FEATURES AND SPECIFICATIONS:The system should trip the motor on power failure and on appearance of any electrical fault mentioned below which may otherwise damage the motor field coils thus providing protection to the motor.1. Low voltage (below 320V) 2. High voltage (above 450 V)3. Single phasing 4. Reverse phasing 5. Un-balanced phasing. In addition the system shall have:a. Separate LED fault indictors. b. LED phase indicators c. An isolation / by pass system d. A siren / audio warning system which activates on starter failure only.6. Over load protection.7. Under load protection.AUTOMATION :The system should provide and test a solid-state water level controller for the synchronized operational automation of the motor of pumpset in a pre-described fashion as follows:-1. Assuming that the sump tank is filled-the motor of pumpset starts automatically and starts running on full load till the water level reaches the described empty tank level and the motor stops. This cycle continues upon filling of sump tank again.2. The system must be supported with an automatic mechanism for anti-corrosion/salt deposition on high speed steel probes for continuous and better conduction of electric signal.3. The system should have a manual operated option in case of appearance of automation fault.4. Job includes providing and laying of 14/60 or suitable rating flexible low resistance copper cable with GI support wire from water tank to the water level controller unit. Job further includes the fixing of steel water level sensor probes in the sump tank by climbing up and fastening copper cable with the sensor probes inside the tank.GSM Mobile Operation:-Designing, providing, installation, testing and commissioning of GSM mobile activation and deactivation switch for pumping machinery through LT control panel. The job includes installation of automation device inside the panel at suitable place. Automation device should be suitable for pumping machinery i.e. HC pump motor set through mobile app from anywhere.It shall be equipped with following features:-a) Device shall have provision for insertion of SIM of any network provider with a recharge top-up of 1 year for uninterrupted motor pumpset operations.b) Device shall be able to register register minimum of 3 mobile numbers for operation.c) Device shall be operated from mobile and shall respond to a call and a sms from the registered mobile numbers for machinery operations i.e. ON and OFF from mobile by call and sms mode.d) Device shall be able to deliver present status of the pumping machinery that is ON/OFF. Testing of panel after making all incoming / outgoing connections on no load and then on full load. Proper earthing of equipment should be done. Job further includes providing of 35mm2 Cu cable 36 metre in length along with proper thimbling and insulation works. Complete job includes cost of material, hire charges of tools and tackles, transportation, loading / unloading and labour charges. (Complete job) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jun 27, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 03, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 2 daysJul 04, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 3 days