Tender For Advertised Rate List /Bill Of Quantity For Development Of Water Sports Centre Cum Boat Club At Wullar Lake .Adv.Cost=Rs 129.22 Lacs
Tender Value
1.29 Crore
Estimated cost
Bid Submission
13 Jul 2026
1 days left
EMD
2.58 Lakhs
Bank guarantee accepted
Document Fee
2600
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bandipora → Jammu and Kashmir
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Advertised Rate List /Bill Of Quantity For Development Of Water Sports Centre Cum Boat Club At Wullar Lake .Adv.Cost=Rs 129.22 Lacs
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. All kinds of soil, |
| 2 | Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. Ordinary Rock |
| 3 | Excavating, supplying and filling of local earth (including royalty)by mechanical transport upto a lead of 5 km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. |
| 4 | Supplying and filling in plinth with fine sand under floors including, watering, ramming, consolidating and dressing complete, including carriage of material from source to site of work |
| 5 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) including carriage of material from source to site of work |
| 6 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centering and shuttering. All work up to plinth level 1:4:8 (1 Cement: 4 coarse sand: 8 grade stone aggregate 40mm nominal size) including carriage of material from source to site of work |
| 7 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centering and shuttering all work upto plinth level in 1:3:6 (1 cement : 3 coarse sand : 6 stone aggregate 20mm nominal size) including curing complete including carriage of material from source to site of work |
| 8 | Supply and filling of dry stone soling in foundation trenches/under floors tightly hand packed with hand ramming, dressing ,watering incld. carriage of material from source to site of work complete |
| 9 | Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) including carriage of material from source to site of work |
| 10 | Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement. 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) including carriage of material from source to site of work |
| 11 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) including carriage of material from source to site of work |
| 12 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m |
| 13 | Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) and curing complete, but excluding the cost of nosing of steps etc. complete, 50 mm thick with 20mm nominal size stone aggregate, including carriage of material from source to site of work |
| 14 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth and curing complete including carriage of material from source to site of work |
| 15 | Centering and shuttering including strutting propping etc. and removal of form for foundation, footings basses of columns etc . including carriage of material from source to site of work |
| 16 | Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams,plinth beams, girders, bressumers, cantilevers and for suspended floors, roofs, landings, balconies and access platforms including carriage of material from source to site of work |
| 17 | Centering and shuttering including strutting, propping etc. and removal of form for columns, pillars, piers, aburtments,posts and struts including carriage of material from source to site of work |
| 18 | Centering and shuttering including strutting, propping etc. and removal of form for stairs (excluding landings) except spiral staircases. including carriage of material from source to site of work |
| 19 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete at all levels, Thermo-Mechanically Treated bars of grade Fe-500D or more, including carriage of material from source to site of work |
| 20 | Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in Cement mortar 1:6 ( 1 cement : 6 coarse sand ) including carriage of material from source to site of work |
| 21 | Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in superstructure above plinth level upto floor five level including curing in Cement mortar 1:6 ( 1 cement : 6 coarse sand ) including carriage of material from source to site of work |
| 22 | Providing and laying vitrified floor tiles (Anti-skid) in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete, Size of tile 600x600 mm, including carriage of material from source to site of work |
| 23 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours and shades, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement and matching pigments etc. complete. Size of tile 600x600 mm including carriage of material from source to site of work |
| 24 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete including carriage of material from source to site of work |
| 25 | Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete. In colour such as White, Ivory, Grey, Fume Red Brown, including carriage of material from source to site of work |
| 26 | Kota stone slab flooring 20 mm thick over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing, polishing and curing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand), including carriage of material from source to site of work |
| 27 | Kota stone slab 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm ( average) thick cement mortar 1:3 (1 cement:3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing, polishing and curing complete. including carriage of material from source to site of work |
| 28 | Extra for pre finished nosing in treads of steps of kota stone/ sand stone slab. |
| 29 | Providing wood work in frames of doors, windows, clesrestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length incld cost of hold fast lugs or dash fasteners complete Second class Deodar wood including carriage of material from source to site of work |
| 30 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: -Butt hinges and necessary screws shall be paid separately).Second class deodar wood 35mm thick including carriage of material from source to site of work |
| 31 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. Plain particle board flat pressed, 3 layer or graded wood particle board medium density Grade I, IS : 3087 marked including carriage of material from source to site of work |
| 32 | Providing and fixing ISI: 12817 marked Stainless Steel Butt Hinges with Stainless Steel screws etc. complete. 100x58x1.90 mm including carriage of material from source to site of work |
| 33 | Providing and fixing ISI: 12817 marked Stainless Steel Butt Hinges with Stainless Steel screws etc. complete. 75x47x1.80 mm including carriage of material from source to site of work |
| 34 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.Second class deodar wood 35mm thick including carriage of material from source to site of work |
| 35 | Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge : Second class deodar wood 35mm thick including carriage of material from source to site of work |
| 36 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc including priming coat with approved steel primer all complete, Fixed to openings / wooden frames with rawl plugs screws etc. including carriage of material from source to site of work |
| 37 | Providing and fixing oxidized M.S. casement stays (straight peg type) with necessary screws etc. complete. 200 mm weighing not less than 120 gms. including carriage of material from source to site of work |
| 38 | Providing and fixing ISI marked oxidized M.S. sliding door bolts with nuts and screws etc. complete 250x16 mm : including carriage of material from source to site of work |
| 39 | Providing and fixing aluminum hanging floor door stopper, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : Twin rubber stopper including carriage of material from source to site of work |
| 40 | Providing and fixing ISI marked oxidized M.S. handles conforming to IS : 4992 with necessary screws etc. complete : 100 mm including carriage of material from source to site of work |
| 41 | Providing and fixing ISI marked oxidized M.S. handles conforming to IS : 4992 with necessary screws etc. complete : 75 mm including carriage of material from source to site of work |
| 42 | Structural steel work welded and bolted in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete, including carriage of material from source to site of work |
| 43 | Providing and fixing colour coated galvalume High Rib profile sheets 0.50 mm TCT (Total coated thickness) having a crest height of 28-32 mm at 195 mm and effective width of 975-1000 mm and length to suit site requirements to the purlins using self drilling and self tapping fasteners of reputed make with purlin sheet using self drilling and self tapping fasteners and fixing flashings,valleys and ridges hips of colour coated galvalume plain sheet using using self drilling and self tapping fasteners of reputed make complete and as directed.All types of steel sheets shall be load tested to satisfy 1.1 times the design wind load and coating thickness to the satisfication of the site Engineer.the fasteners shall also be load tested including cost of ridges and hips of width 60 cm overall width plain colour coated sheets and valleys of 90 cm width overall of Pre-colour coated plain sheets of required size and thicknes complete 0.50 mm thick all inclusive.The Contractor has to submit design and drawing for approval on the sheet profile ,design and fabrication deatail before installation incld cost and carriage of all material involved from source to site of work. |
| 44 | Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works, including carriage of material from source to site of work |
| 45 | Providing and fixing on wall face un-plasticized Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes 110 mm diametre including carriage of material from source to site of work |
| 46 | Providing and fixing on wall face un-plasticized - PVC moulded fittings/accessories for un plasticized Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion Coupler 110mm. including carriage of material from source to site of work |
| 47 | Providing and fixing on wall face un-plasticized - PVC moulded fittings/accessories for un plasticized Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion Single tee without door 110x110x110 mm . including carriage of material from source to site of work |
| 48 | Providing and fixing on wall face un-plasticized - PVC moulded fittings/accessories for un plasticized Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion Bend 87.5° 110 mm bend . including carriage of material from source to site of work |
| 49 | Providing and fixing un-plasticised -PVC pipe clips of approved design to un-plasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm including carriage of material from source to site of work |
| 50 | Providing and fixing plained eaves boarding. 2nd class Deodar wood 250x32 mm (nominal size) including carriage of material from source to site of work |
| 51 | 12mm Cement plaster of mix in 1 : 6 ( 1 cement : 6 coarse sand) including carriage of material from source to site of work |
| 52 | 15 mm Cement plaster on the rough side of single or half brick wall of mix: 1:6 (1 cement:6 coarse sand) including carriage of material from source to site of work |
| 53 | 6mm cement plaster to ceiling of mix 1 : 3 (1 cement: 3coarse sand) including carriage of material from source to site of work |
| 54 | 12mm Cement plaster finished with a floating coat of neat cement of mix: 1 : 4 ( 1 cement : 4 fine sand) including carriage of material from source to site of work |
| 55 | Providing and applying white cement based putty 2 mm thick of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete including carriage of material from source to site of work |
| 56 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and inluding priming coat with water thinnable cement primer including carriage of material from source to site of work |
| 57 | Applying one coat of water thinable cement primer of approved brand and manufacture on wall surface including carriage of material from source to site of work |
| 58 | Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm), including carriage of material from source to site of work |
| 59 | Applying priming coat With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood) including carriage of material from source to site of work |
| 60 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade.Two or more coats on new work including carriage of material from source to site of work |
| 61 | Making soak pit 2.5 m diameter 3.0 meter deep with 45x45 cm dry brick honey comb shaft with common burnt clay (non modular) bricks of class designation 7.5 bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design including all carriages and costs of material involved from source to site of work |
| 62 | Supply ,stacking, filling,laying and spreading of GSB in 15 cm layers to specified lines,grades and cross sections incld sorting ,spreading to templete ,watering ,dresssing ,ramming and consolidation to the required gradient and camber with 8-10 tonne capacity Power road roller incld. carriage of material from approved source to site of work complete |
| 63 | Sanitary Installations :-Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid. including carriage of material from source to site of work |
| 64 | Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required :White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps including carriage of material from source to site of work |
| 65 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer - in - charge. including carriage of material from source to site of work |
| 66 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete: Flexible pipe 40 mm dia including carriage of material from source to site of work |
| 67 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040mm bowl depth 250mm including carriage of material from source to site of work. |
| 68 | Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. including carriage of material from source to site of work |
| 69 | Providing and Fixing of PVC soil/waste/ventellating pipes with fittings like P-bend,D-bend,P or S-trap,F-Trap, collar, junction Door /Tee, Reducer, stays /clamps,vent cowel etc (B-Type) of approved brand and manufacture (Prince/ Supreme or Equivalent brand) 50 mm dia including carriage of material from source to site of work |
| 70 | Providing and Fixing of PVC soil/waste/ventellating pipes with fittings like P-bend,D-bend,P or S-trap,F-Trap, collar, junction Door /Tee, Reducer, stays /clamps,vent cowel etc (B-Type) of approved brand and manufacture (Prince/ Supreme or Equivalent brand) 75 mm dia including carriage of material from source to site of work |
| 71 | Providing and Fixing of PVC soil/waste/ventellating pipes with fittings like P-bend,D-bend,P or S-trap,F-Trap, collar, junction Door /Tee, Reducer, stays /clamps,vent cowel etc (B-Type) of approved brand and manufacture (Prince/ Supreme or Equivalent brand) 110 mm dia including carriage of material from source to site of work |
| 72 | Providing fixing testing and commissioning of PVC waste pipe of approved make(UPVC pipes agri pipes of 6 kg/sq.cm or foam core SN-4 pipes) confirming to IS:4985 for drainage system cut to required length, pipe to be laid below ground level in trenches upto required depth to the required slope.(for complete external under ground sewer drainage network) PVC S&S Pipe 160mm dia including carriage of material from source to site of work |
| 73 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge. Concealed work,including cutting chases and making good the walls etc .20mm nominal outer dia pipes. including carriage of material from source to site of work |
| 74 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge. Concealed work,including cutting chases and making good the walls etc .25mm nominal outer dia pipes. including carriage of material from source to site of work |
| 75 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge. Concealed work,including cutting chases and making good the walls etc .32mm nominal outer dia pipes. including carriage of material from source to site of work |
| 76 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge. External work including trenching, refilling etc.32mm nominal outer dia pipes. including carriage of material from source to site of work |
| 77 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge. External work including trenching, refilling etc.50mm nominal outer dia pipes. including carriage of material from source to site of work |
| 78 | Providing and fixing PTMT bib cock of approved quality and colour. 15 mm nominal bore, 165 mm long, weighing not less than 110 gms. including carriage of material from source to site of work |
| 79 | Providing and fixing PTMT pillar cock of approved quality and colour.15 mm nominal bore 125 mm long foam flow, weighing not less than 120 gms. including carriage of material from source to site of work |
| 80 | Providing and fixing PTMT stop cock of approved quality and color. 15 mm nominal bore, 86 mm long, weighing not less than 88 gms. including carriage of material from source to site of work |
| 81 | Providing and fixing PTMT Ball cock of approved quality, colour and make complete with epoxy coated aluminium rod with L.P/H.P.H.D plastic balls. 25mm nominal bore, 152mm long, weighing not less than 440gms. including carriage of material from source to site of work |
| 82 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement: 2 fine sand) including testing of joints etc. complete 150 mm dia. R.C.C. pipe including carriage of material from source to site of work |
| 83 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarsesand (zone- III) : 8 graded stone aggregate 40 mm nominal size),inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size) finished with a floatingcoat of neat cement complete as per standard design Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including carriage of material from source to site of work |
| 84 | Extra for depth for manholes Size 90x80 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 85 | Providing and fixing square- mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design.180 x 150 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including carriage of material from source to site of work |
| 86 | Providing and fixing CPVC Union in CPVC pipe including cutting and threading the pipe and making long screws etc. complete (new work) 20 mm nominal bore including carriage of material from source to site of work |
| 87 | Providing and fixing CPVC Union in CPVC pipe including cutting and threading the pipe and making long screws etc. complete (new work) 25 mm nominal bore including carriage of material from source to site of work |
| 88 | Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour 25 mm nominal bore, weighing not less than 62gms including carriage of material from source to site of work |
| 89 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing Rectangular shape 1500x450 mm including carriage of material from source to site of work |
| 90 | Providing and fixing 15 mm nominal bore C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. including carriage of material from source to site of work |
| 91 | Providing and placing on terrrace (at all floor levels) polyethene water storage tank ISI:12701 marked triple layer indicating the BIS License No with cover and suitable locking arrangement and making necessary holes for inlet,outlet and overflow pipes but without fittings and base support for tank (Sintex, Electroplat, Star, Lotus or equivalent having valid ISI license) including carriage of material from source to site of work |
| 92 | Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931 including carriage of material from source to site of work |
| 93 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. including carriage of material from source to site of work |
| 94 | Providing & Fixing of 2.0 HP water Motor with all fittings like inlet and outlet connections , electric controlled setup with service line including making of Plateform as per requirement covered with CGI Sheet fixed over angle iron frame work with all fittings as per the directions of Engineer In-Charge Complete job ( Kirlosker, Usha, Cromptom Greaves, Havelles or equivalent) including carriage of material from source to site of work |
| 95 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet 100 mm diameter including carriage of material from source to site of work |
| 96 | Providing and fixing Towel Rail CP brass 750 x20mm together with a pair of CP brass brackets to fit the size of towel rail including carriage of material from source to site of work |
| 97 | Providing and fixing toilet paper holder C.P. brass including carriage of material from source to site of work |
| 98 | Providing and fixing PVC NT 125 mm dia including carriage of material from source to site of work |
| 99 | Providing and fixing of SOLAR WATER HEATER (100 liters) pressurised stainless steel tank including stand,water storage tank as per the Specification as under ;- 1. Main Storage Tank:- Capacity: 100 Liters Inner Tank Material: Food-grade Stainless Steel (SS 304) (thickness: 0.5 mm to 0.7 mm) or Glass-Lined/Enamel Coated Mild Steel to resist corrosion. Outer Tank Material: Stainless Steel (SS 430). Pressure Capacity: Tested up to 6 to 10 bar, designed for a continuous working pressure of up to 4 to 8 bar. Insulation: 50 mm to 55 mm high-density Polyurethane Foam (PUF) to retain heat for up to 48 to 72 hours. Safety & Maintenance: Equipped with a Pressure Relief Valve, Air Vent, and a Sacrificial Magnesium Anode rod to prevent electrochemical corrosion and fight water hardness.2. Solar Collector (Evacuated Tube Collector - ETC) :- Tube Type: Three-layer, highly absorptive vacuum tubes. Tube Dimensions: 58 mm (Diameter) × 1800 mm or 2100 mm (Length). Number of Tubes: 8 to 10 tubes. Working Principle: Thermosiphon system3. Support Stand:- Material: Stainless Steel for rust prevention. Design: rigid structure designed to evenly distribute the weight of the water tank and withstand high wind speeds. Tilt Angle: Standard 15° to 45° depending on the latitude of the installation location. [1, 2, 3, 4]4. Cold Water Storage / Overhead Tank (Customer's Existing Setup):- Requirements: The overhead tank (syntax or syntax-style) should be placed at least 3 feet (approx. 1 meter) higher than the solar system’s highest point.Pressure Compatibility: Because this is a pressurized unit, it does not strictly require an auxiliary float tank and can handle direct feed from a pressure booster pump.(Sample to be got approved from the competent authority before Installation) including all carriages and costs of material involved from source to site of work complete job |
| 100 | Providing and fixing of water heating geysers of approved brand & quality (Venus/ Jaguar/ Racold or eqviuallent) with all necessary fittings and fixtures complete Job. 50 Ltr capacity ( Sample to be got approved from the competent authority) including carriage of material from source to site of work |
| 101 | Providing and fixing of water heating geysers of approved brand & quality with all necessary fittings and fixtures complete Job. 35 Ltr capacity( Sample to be got approved from the competent authority) including carriage of material from source to site of work |
| 102 | Road :-Supply and stacking at site Graded Crushed stone aggregrate of size 53 mm to 22.4 mm ( Quarry crushed ). and stone screening of size 11.2 mm nominal size (type B), stone Dust as biding material incld laying ,spreading and compacting stone aggregrate of specified sizes to WBM specifiacations in uniform thickness (75 mm compacted ) ,hand picking ,rolling with 3 wheeled road /vibratory roller 8-10 tonne capacity in stages to proper grade and camber ,applying and brooming requisite type of screening /binding material to fill up interstices of course aggregrate ,watering and campacting to the required density including carriage of material from source to site of work |
| 103 | Supply ,stacking, filling,laying and spreading of khakh Bajree/GSB in 15 cm layers to specified lines,grades and cross sections incld sorting ,spreading to templete ,watering ,dresssing ,ramming and consolidation to the required gradient and camber with 8-10 tonne capacity Power road roller including carriage of material from source to site of work |
| 104 | Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper to site, for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge, incld all carriages from source upto the site of work complete job |
| 105 | Providing and applying tack coat using hot straight run bitumen of grade – VG-10, including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing road surface as per specifications.On W.B.M. @ 0.75 Kg/sqm. including carriage of material from source to site of work |
| 106 | Providing and laying bituminous macadam using crushed stone aggregates of specified grading premixed with bituminous binder, transported to site by tippers, laid over a previously prepared surface with paver finisher equipped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to achieve the desired compaction and density, complete as per specifications and directions of Engineer-in-Charge. 50 to 100 mm average compacted thickness with bitumen of grade VG-10 @ 3.5% (percentage by weight of total mix) prepared in Drum Type Hot Mix Plant of 60-90 TPH capacity, including carriage of material from source to site of work |
| 107 | Providing and laying semi- dense Bituminous concrete using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equipped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction and density as per specification, complete and as per directions of Engineer-in-Charge.25 mm compacted thickness with bitumen of grade VG 10 @ 5% (percentage by weight of total mix) and lime filler @ 2% (percentage by weight of Aggregate) prepared in Drum Type Hot Mix Plant of 60-90 TPH capacity. including carriage of material from source to site of work |
| 108 | Providing and laying 6 mm thick seal coat of premixed fine aggregate (passing 2.36 mm and retained on 180 micron sieve) with bitumen using 128 kg of bitumen of grade VG-10 bitumen per cum of fine aggregate and 0.60 cum of fine aggregate per 100 sqm of road surface including rolling and finishing with road Rollar all complete. including carriage of material from source to site of work |
| 109 | Electric Part :- Wiring for light point/ fan point/ exhaust fan point/ call bell point with 2X 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor (Polycab Green/Havell Life guard/ Fenolex/ Salzer/RR/Apar make as desired by engineer incharge ) single core cable in surface / recessed medium class PVC conduit, with modular switch Antibacterial series ( Legrand /ABB / Siemens make.), modular plate,suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. including carriage of material from source to site of work |
| 110 | Wiring for twin control light point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor (Polycab Green/Havell Life guard/ Fenolex/ Salzer/RR/Apar make as desired by engineer incharge ) single core cable in surface / recessed medium class PVC conduit, 2way modular switch,Antibacterial series ( Legrand /ABB / Siemens make.) modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required. including carriage of material from source to site of work |
| 111 | Wiring for light/ power plug with 2X4 sq. mm + 1X 4 sq. mm earth wire , FRLS/HFFR PVC insulated copper conductor (Polycab Green/Havell Life guard/ Fenolex/ Salzer/RR/Apar make as desired by engineer incharge )) single core cable in surface /recessed medium class PVC conduit. including carriage of material from source to site of work |
| 112 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor (Polycab Green/Havell Life guard/ Fenolex/ Salzer/RR/Apar make as desired by engineer incharge ), single core cable in surface/ recessed medium class PVC conduit as required. including carriage of material from source to site of work 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 113 | 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 114 | 2 X6 sq. mm + 1 X 6 sq. mm earth wire |
| 115 | 2 X 16 sq. mm + 1 X 6 sq. mm earth wire |
| 116 | 2 X 10 sq. mm + 1 X 6 sq. mm earth wire |
| 117 | Supplying and fixing modular blanking plate on the existing modular plate and switch box excluding modular plate as required |
| 118 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, Antibacterial series ( Legrand /ABB / Siemens make.)connections etc. as required. including carriage of material from source to site of work |
| 119 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch,modular plate, suitable GI box , connections etc. as required. Modular Switch & Socket:- Antibacterial series ( Legrand /ABB / Siemens make.) including carriage of material from source to site of work |
| 120 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings). Modular Switch & Socket:- Antibacterial series ( Legrand /ABB / Siemens make.) including carriage of material from source to site of work |
| 121 | Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top along with 30 A \\"C\\" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required including carriage of material from source to site of work |
| 122 | Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, \\"C\\" curve including connections, painting etc. as required.Antibacterial series ( Legrand /ABB / Siemens make.) including carriage of material from source to site of work |
| 123 | Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.Antibacterial series ( Legrand /ABB / Siemens make.) including carriage of material from source to site of work |
| 124 | Supplying and fixing of following sizes of medium class PVC conduit( Anchor/ Ravindra/ Eq. make)along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required, with cement plaster, wall putty , paint, complete 25 mm including carriage of material from source to site of work |
| 125 | Supplying and fixing of following sizes of medium class PVC conduit( Anchor/ Ravindra/ Eq. make)along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required, with cement plaster, wall putty , paint, complete 32 mm including carriage of material from source to site of work |
| 126 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB /RCCB / Isolator ) .(legrand / Schinider/ L&T ./ABB/equivalent standard make as directed by engineer incharge.) 6 way (4 + 18), Double door including carriage of material from source to site of work |
| 127 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\"curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.(legrand / Schinider/ L&T ./ABB/equivalent standard make as directed by engineer incharge.) Single Pole including carriage of material from source to site of work |
| 128 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\"curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.(legrand / Schinider/ L&T ./ABB/equivalent standard make as directed by engineer incharge.) Single Pole and neutral including carriage of material from source to site of work |
| 129 | Supplying and fixing 40 A to 63 A rating, 240/415 V, 10 kA, \\"C\\"curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.(legrand / Schinider/ L&T ./ABB/equivalent standard make as directed by engineer incharge.)Single pole and neutral including carriage of material from source to site of work |
| 130 | Supplying and fixing single pole blanking plate in the existingMCB DB complete etc. as required including carriage of material from source to site of work.including carriage of material from source to site of work . |
| 131 | LED Down lighter (SMD Type) (System lumen efficacy ≥ 110 < 135 lm/Watt )Supplying, Installation, Testing & Commissioning of LED Recessed/ surface Down lighter (Round/square/ Rectangular) SMD type of following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz,Operating temp range -50C to 400C, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80,UGR (Unified Glare Rating) < 19, Flicker free (flicker should be below 5%), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K /4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM (Standard Deviation Colour Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be confirming to relevant BIS standards. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing Complete in all respect i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc.as required with Minimum 5 year OEM warranty.System lumen efficacy ≥110and <135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C) Powder coated die cast /Extruded aluminium Body including trim ), Philips/ Wipro/ Helonix make / sample to be approved before installation.. including carriage of material from source to site of work 12 -15 watt |
| 132 | 18 watt |
| 133 | LED Street light fixture, powder coated pressure die cast aluminium body (System lumen efficacy>135 lm/Watt) Supplying, Installation, Testing & Commissioning of Flood Light, powder coated pressure die castaluminium body with built in or separate driver as per the requirement with Driver efficiency >85%, Input voltage: Input voltage: 140-270 Volt AC,frequency 50/60 hz, Operating temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2, P. F.≥0.95, IP-66,IK-10, CRI >70, under voltage and over voltage protection, EMI-EMC as per CISPR -15, lenses for beamangle 30 deg-120deg as per the application and the project requirement., suitable tilt able fitting, life time (LED, Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumenmaintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin) , SDCM(Standard Deviation Color Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard complete in all respect i/c external connections with 1.5 sq mmFRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with inimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt output .LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted.. Shape sizeand CCT shall be as approved by Engineer-in- Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LEDjunction temperature shall not rise above 90°C).), Philips/ Wipro/ Helonix make / sample to be approved before installation.. including carriage of material from source to site of work 50 watt |
| 134 | Supply installation testing and commissioning of Ceiling Fan 3 Star Rated with Voltage Range 90 V to 300 V,Min. Air Delivery 212 CMM,Service Value 5.3 Cu.m/min/watt,Aluminium Blades ,including wiring the down rods of standard length(Upto 45 cm)with 1.5 sq.mm FR PVC insulated,copper conductor,single core cable including providing and fixing phenolic laminated sheet cover on the Fan Box etc as Required. ), USHA/ Crompton /Orient make / Helonix /sample to be approved before installation.1200 mm. including carriage of material from source to site of work |
| 135 | Supply,Installation,Testing and Commissioning 486 Cu.m/Hr. AC 220-240 Volts, 50 Hz exhaust fan made out of Metal Body with inbuilt thermo cutoff Protection and Noise Level not exceeding 37 dB of Following Sizes including connection etc. complete as required .), USHA/ Crompton /ORIENT/Helonix make / sample to be approved before installation. 200- 250 mm including carriage of material from source to site of work |
| 136 | LED Batten light (System lumen efficacy ≥120 <135 lm/Watt) Supplying, installation, Testing & Commissioning of LED surface mounted Batten light of following bodymaterial and construction as per IS : 10322 with driver (Replaceable) as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 0C to 40 0C, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P.F.≥0.95, IP20, CRI >80, Flicker free (flicker shouldbe below 5 %), life time (LED,Driver & electrical circuitry), of minimum 50000 Burning Hourswith 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour Matching) <3, Maximum power consumption should not more than the specified rating andFixture shall be of relevant BIS standard.Manufactures Word Mark/ Name Engraved/Embossing/ Screen printing on housing. completein all respect i/c external connections with 1.5sq.mm FRLS/HFFR, PVC insulated copperconductor single core cable and earthing etc. asrequired with Minimum 5 year OEM warranty.System lumen efficacy ≥120 <135 lm/Watt output .LM79 & LM80 Test report and all testing requiredfor LED fixtures as per BIS shall be submitted.Shape size and CCT shall be as approved byEngineer-in-Charge as per requirement. (Thermalmanagement: heat sink of aluminium housingsuch that LED junction temperature shall not riseabove 90°C).),Philips/ Wipro/ Regent/Endo/LT make / sample to be approved before installation..20watt including carriage of material from source to site of work |
| 137 | Supply installation testing and commissioning of IP:20 Decorative Light 10W-12 W +- 1 W LED Surface Mounted 2 ft. with system lumen efficacy of 100 lm/W and P.F >0.9 THD <20% CCT 6500K,CRI 80 .The LED should have life of 50000 Burning Hours at L70.The input voltage shall be 150 V to 270 V.The fixture should have inbuit surge protection of 2KV.Certification-LM 79 and LM 80.The test report should be from Govt. Approved Lab/inhouse NABL Lab. ), Philips/ Wipro/ Regent/Endo/LT make / sample to be approved before installation. including carriage of material from source to site of work |
| 138 | Supply installation testing and commissioning of IP65 led Bulk head 10 W +/- 1 W LED Surface Pressure Die Cast Aluminum system lumen efficacy of 100 lm/W with Polycarbonate Opal Diffuer and P.F.>0.95 ,THD<10% ,CCT 5700K, CRI 80, IK rating IK08. The LED with Useful life of 50000 Hrs at L70. The Input voltage range shall be 150V to 265V. The Fixture should have In-built Surge Protection of 2.5kV Certification:- LM79 & LM80 test report should be from govt approved Inhouse NABL lab/ government of India authorised lab .), Philips/ Wipro/ Regent/ Endo /LT make / sample to be approved before installation. including carriage of material from source to site of work |
| 139 | Supplying, installation of Ceiling Hung 3 colour Designed Direct and Indirect Multiglass LED Chandelier 40-50 Watt . The luminaire shall be with BIS Registered electronicdriver with input voltage range of 90 to 265V , THD # 10% & PF # 0.9, 50,000 Hrs LED Life with L70 Criteria. The LED Driver shall beeasily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge protection of 2KV.Theluminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo Biological SafetyStandard.), Philips/ Jaguar /Wipro make / sample to be approved before installation. including carriage of material from source to site of work |
| 140 | S/L , testing and commissioning of PVC XLPE insulated alluminium armoured cable 650 V/1100 V Grade as per IS 7098 (Part 1) 1988 with upto Date Amendments.Havell/Eq. standard make as directed by engineer incharge and making end termination with brass compression gland and aluminium lugs of required size. 95 sq.mm 3.5 core including carriage of material from source to site of work |
| 141 | S/L , testing and commissioning of PVC XLPE insulated alluminium armoured cable 650 V/1100 V Grade as per IS 7098 (Part 1) 1988 with upto Date Amendments.Havell/Eq. standard make as directed by engineer incharge and making end termination with brass compression gland and aluminium lugs of required size. 35 sq.mm 3.5 core including carriage of material from source to site of work |
| 142 | Design, Fabrication, Supplying, Installation, Testing and Commissioning of following panel, duly manufactured from CPRI approved manufacturer, made out of 2mm thick M.S. sheet steel , floor/wall mounted, vermin and dust proof, indoor type with suitable size of angle iron legs for grouting in the ground, with lockable type hinged doors, duly painted with provision for fixing of following switch gears, , Aluminium Bus Bar of various ratings after taking Derating factor into account, and other allied accessories etc. as required.( As per approved design,size may vary as per site requirement) including carriage of material from source to site of work |
| 143 | Providing and fixing of following protection equipments and other allied accessories including connections, inter connections, with suitable size of PVC insulated copper conductor cable including earthing etc. as required. including carriage of material from source to site of work NORMAL INCOMING:- 160A 4P MCCB 36 KA including spreader links including spreader links, icu=ics=100% ( Adjustable thermal and Adjustable magnetic release ) Legrand/ Shinider/Semiens/ABB make. |
| 144 | 4 No. of Aluminium Bus Bar of 300 Amp |
| 145 | Digital meters and phase indicators -1 set. |
| 146 | Onload Change over switch 100 Amp for generator.Front operated. |
| 147 | 4 No. of Aluminium Bus Bar of 200 Amp. |
| 148 | Digital meters and phase indicators -1 set. |
| 149 | OUTGOING:- 40-63amp TPN MCB 10KA |
| 150 | 40-63amp DP MCB 10KA |
| 151 | Space for 12 way MCB's |
| 152 | Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. including carriage of material from source to site of work |
| 153 | Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm) including carriage of material from source to site of work |
| 154 | S/I testing and comm. Of three phase 20 KVA 50HZ oil cooled(Transformer oil is to be provided with stabilizer conforming to IS 335,IEC296)) unbalanced type servo voltage stabilizer(A.E / Cosco/ chinar/ Electricfield make) having an input voltage ranging from 156V to 415 V ( phase to phase) and balanced output voltage of 415V, +/- 1%. ( Test certificate to be provided by the manufacturer) The unit incorporate ( A) 0-500V digital voltmeter with selector switch. (B) A three phase change over switch to read voltage on incoming and output side (C) indicating lights 6 No two numbers for each of the motorised units, one for lower limit and other for higher limit. (D) six push button control for movement operation of three motorised dimmer units two for each unit i.e one for raise operation and one for lower operation under the conditions of adjustment of auto/mannual selector switch (DPDT) (E) Single phase Preventer ( contactor Switch of required rating) Legrand make (F) six potential meter resistance with lock meter two for each phase control, one for sensitivity and other for level control. (G) two sets of indication lamps three numbers each to indicate output and input indication (H) 20 % over load bearing capacity for one hour. |
| 155 | Supply installation testing and commissioning of Sine Wave Inverter Capacity 5 KVA, Rated Power 4000 W, along with Four number invertor battery 150 AH/12 V Exide invatubular/ equivalent make,24 Month Warranty Safe for sensitive appliances with Sine wave out-put, Inverter should run heavy loads like AC, Geyser, Photocopiers, Auto over-load handling capacity Installation and maintenance friendly Offers high quality and reliable power back-up solution for office and homes ,MCB for protection from Input mains,Bypass switch for supplying output directly from grid in case of Home UPS fault.Noiseless Operations with the help of low harmonic distortion, Intuitive Display to easily understand status of mains availability, battery status, etc.Comprehensive protection against short-circuit, reverse polarity, battery over-charge, deep-discharge etc.Adaptive Battery charging control system technology (ABCC) ensures faster battery charging and enhances battery life by around 70%.Supports a wide battery range, i.e. Flat Plate, Tubular & VRLA (SMF).praffered make Luminous/ Microtek/Exide make. the job also includes, Supply and fabrication of angle iron stand of Structural steel work in built up sections, and framed work,including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. including carriage of material from source to site of work |
| 156 | Supplying,Installation,Testing and Commissioning of CO2 Type Fire Extinguisher 4.5 Kg. Capacity ISI Mark(IS:15683)suitable for 'B' and 'C' class fires - inflammable liquids, gaseous fires like L.P.G. and acetylene, and electrical including carriage of material from source to site of work |
| 157 | Supplying, installation, testing and commissioning of Decorative Wall Light fitting of Philips / Wipro / Jaquar or equivalent approved make, suitable for aesthetic indoor illumination in galleries, lobbies, corridors, or display areas, complete with LED light source and all required accessories for proper installation and operation.Technical Specifications:Type: Decorative Wall Mounted Luminaire (indoor type)Light Source: Integrated LED or LED lamp with holder (as per design)Wattage: 10W to 25W (as required)Input Voltage: 220–240V AC, 50 HzColour Temperature (CCT): 3000K / 4000K (Warm / Neutral White as specified)CRI (Colour Rendering Index): ≥80Housing: Die-cast aluminium / glass / polycarbonate with high-quality decorative finishFinish / Colour: Chrome / Matt / White / Designer finish (as approved)Mounting: Wall-mounted type with concealed wiring connection boxProtection Class: IP20 or higher, suitable for indoor useAccessories: Mounting brackets, fasteners, connector block, and other hardware complete in all respects.Make: Philips / Wipro / Jaquar / equivalent approved by Engineer-in-Charge. including carriage of material from source to site of work |
| 158 | Supply installation testing and commissioning of energy efficient 1.5 Ton inverter type split Air Conditioning system suitable for operation on AC supply single phase 220 V . The indoor unit fitted on wall by employing suitable clamps and the outdoor unit fitted on the wall by using suitable angle iron stand fitted with nuts/bolts outside the room to avoid noise, including standard length of suitable size copper tubing covered with nitrilic foam, topping up with refrigerant for additional length of piping if required, PVC flexible drain pipe, suitable capacity 3 core sheathed/ pvc insulated coper cable and a battery operated wireless remote unit. the job also includes repairs to walls wherever the same are cut and the AMC of AC for a period of one and a half year from date of successful commissioning.( Mitsubishi/Toshiba/O-General/ equivalent standard make as desired by Engineer Incharge) including carriage of material from source to site of work |
| 159 | Supply, Installation, testing and commissioning of relay type voltage stabilizer suitable for 1.5 Ton - 2 Ton AC operating from input voltage 90-260 Volts thereby producing output voltage of 230 volts +/- 3 % ( Vguard/ Livgaurd/LG make) including carriage of material from source to site of work |
| 160 | Taking of photographs of size 125mm x 100mm Pre Execution, During Execution, and Post Execution to be submitted with bill complete Job. (Geo tagged photographs showing Longitude and latitude) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jun 27, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 13, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 1 dayJul 14, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 2 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender