|
| 1 | Demolition of cement concrete un -reinforced in ground floors and pavings n.exc 15cm thickness complete all as specified. |
| 2 | M&L for 25mm thick cement concrete type B-1, 1:2:4 (20mm grade aggregate) as in levelling coarse in flooring finished even and fair under floor finishes. |
| 3 | M&L for Glazed ceramic glossy finish tiles coloured in vertical surface 450X300X7mm in any pattern of light & dark/highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and jointed in cement slurry over & including 10 mm thick rendering in cement mortar (1:3) and pointed in white cement with pigment to match the colour of tiles including dismantling of old tiles complete all as specified. |
| 4 | M&L for Non Skid ceramic tiles colour tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4 for laying floor finishes including demolition of old tiles complete all as specified. Note : Work will be in patches or in bulk |
| 5 | M & L for Single charge, stainfree, vitrified tiles, Premium (1st) quality straight edge, coloured tiles 600 X 600 mm and 9-10 mm thick, as in floors etc. in any pattern of light coloured tiles as in approved shade, set & jointed in neat cement including and over 15mm th screed bed in CM (1:4) and pointed in white coloured cement to match, in floors etc including demolition of old tiles complete all as specified. |
| 6 | Ditto as item 5 above but as in skirting over cement mortar backing plaster in CM1:3 10mm thick including dismantling of old tiles complete all as specified and directed. |
| 7 | Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles in all as specified |
| 8 | M & L for Providing precast cement concrete solid building blocks or slabs 10cmthick (with plain or interlocking joints as directed) in PCC 1:3:6 type C1 using 20mm graded aggregate and setting in mortar 1:4 complete, in walls |
| 9 | Taking down cement or cement lime plaster, any description on brick or stone/block walls etc including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off the premises and leaving the work clear for plastering complete all as specified and as directed. |
| 10 | M&L for Ready mix plaster 15mm thick on fair faces of brick work or stone surfaces or rcc member finished even and smooth without using extra cement complete all as specified and directed. |
| 11 | M&L for Ready mix plaster 15mm thick on other than fair faces of brick work or stone surfaces or rcc member , finished even and smooth without using extra cement complete all as specified and directed. |
| 12 | M & L for Ready mix plaster 5 mm thick on ceiling surfaces finished even and smooth without using extra cement, complete, all as specified and directed. |
| 13 | M&L for 10mm Ready mix plaster for dubbing coat for the additional thickness( of ant thickness) is provided as floating/setting coat for stone masonary wall plaster complete all as specified and directed by Engineer-in-Charge. |
| 14 | M&L for Chipping of 50mm average thickness unsound/weak concrete material from slabs, beams, columns, footings etc. and plaster with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts complete all as per direction of Engineer-In-Charge |
| 15 | M&L for Cleaning & applying rust remover on in two coats over rusted reinforcement surface of RCC members and providing anti corrosive coating with two component epoxy based zinc rich primer/Rust passivation Inhibitor coat at the rate of 2-3 sq. mtr/ltr not less than 50 microns dft to reinforcement surface as per manufacturer’s instructions including all machinery, tools tackles and clearing of debris.(Note : Entire Exposed Surface of RCC members after chipping shall be measured and paid.) |
| 16 | M&L for providing 25 to 30mm Micro concrete M-50 (Minimum grade) with CICO MICROCONCRETE at the rate of 25kg per 0.0125 m3 with 20% properly graded 5mm to 10mm silt free aggregate as per manufacturer instructions and mixing concrete with mechanically electrically operated mixer machine including proper props and structural steel support for any height if required ,old surface apply with epoxy bonding agent etc all as specified and directed.Make: CICO MICROCONCRETE of CICO Technologies Ltd or equivalent in Fosroc/STP/BASF. |
| 17 | M&L for Epoxy Bonding Agent suitable for bonding new to old concrete, bricks and steel components, bricks, tiles etc after the prepration of old concrete/RCC surface by cleaning and removing of dust, dirt, loose particles, laitance etc by wire brushing, scrapping and washing with water complete all as per manufacturer's instructions.(Make: Dr. Fixit or Equivalent) |
| 18 | M&L for preparing new plastered or unplastered surfaces of walls, and applying two coats of distemper oil emulsion over a coat of interior wall primer complete all as specified and directed. |
| 19 | M&L for preparing new plastered or unplastered surfaces of walls, and applying three coats of white wash complete all as specified and directed. |
| 20 | M&L for preparing new plastered or unplastered surfaces of ceiling, and applying three coats of white wash complete all as specified and directed. |
| 21 | M&L for preparing old plastered or unplastered surfaces of walls including filling of cracks/holes by crack filler, removing unnecessary nails and applying one coat of oil bound distemper/ emulsion complete all as specified and directed. |
| 22 | M&L for preparing old plastered or unplastered surfaces of walls including filling of cracks/holes by crack filler, removing unnecessary nails and applying one coat of white wash complete all as specified and directed. |
| 23 | M&L for preparing old plastered or unplastered surfaces of ceiling, including filling of cracks/holes by crack filler, removing unnecessary nails and applying one coat of white wash complete all as specified and directed. |
| 24 | M&L for special treatment to floor/wall sunken portion with demolition of PCC with plaster of entire sunken area (bottom & sides upto skirting level) including removal of demolished material exc 250m and n exc 500m, prepration of surface by cleaning to remove loose particles, dust, latance etc, replacement of floor trap, and applying 10mm thick plaster in CM (1:3) with WPC liquid Conplast 421,and applying one coat each of Nitoproof 100 priming coat @1Ltr/5Sqm, after the priming coat applying Nitoproof 120 on plastered surfaces @1Ltr/2.5Sqm, filling the sunken floor with PCC (1:5:10) using brick bat and WPC Conplast - 421, rendering again 20mm thick in CM (1:4) mixed with WPC Conplast - 421, area of floor for kitchen/WHB trap upto 0.25Sqm complete all as specified and as directed. |
| 25 | M&L for special treatment to floor/wall sunken portion with demolition of PCC with plaster of entire sunken area (bottom & sides upto skirting level) including removal of demolished material exc 250m and n exc 500m, prepration of surface by cleaning to remove loose particles, dust, latance etc, replacement of floor trap, and applying 10mm thick plaster in CM (1:3) with WPC liquid Conplast 421,and applying one coat each of Nitoproof 100 priming coat @1Ltr/5Sqm, after the priming coat applying Nitoproof 120 on plastered surfaces @1Ltr/2.5Sqm, filling the sunken floor with PCC (1:5:10) using brick bat and WPC Conplast - 421, rendering again 20mm thick in CM (1:4) mixed with WPC Conplast - 421, complete all as specified and as directed. |
| 26 | Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing, etc. measured separately) exc 250 Ltrs and n exc 500 Ltrs capacity complete all as specified. |
| 27 | Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing, etc. measured separately) exc 500 Ltrs and n exc 1000 Ltrs capacity complete all as specified. |
| 28 | Cleaning & removing all scale and dirt etc from tank and from mouth of circulating pipe etc exc 250 Ltrs and n exc 500 Ltrs capacity complete all as specified. |
| 29 | Cleaning & removing all scale and dirt etc from tank and from mouth of circulating pipe etc exc 500 Ltrs and n exc 1000 Ltrs capacity complete all as specified. |
| 30 | Dismantling of water tanks (RCC hume/PVC) Exc 250 and n exc 500 ltrs including disconnecting all connections etc. complete for following capacity of tanks complete all as specified and directed. |
| 31 | Dismantling of water tanks (RCC hume/PVC) Exc 500 and n exc 1000 ltrs including disconnecting all connections etc. complete for following capacity of tanks complete all a specified and directed. |
| 32 | S&F for new rotational moulded polythylene water storage tank Exc 250 and n exc 500 ltrs (cylindrical/vertical with closte top) hoisted and fixed in position all as specified in SSR Part-I including providing and fixing ball brass valve high pressure with polythene float and fly nut, 20mm bore and tank nipple complete all as specified and directed. |
| 33 | S&F for new rotational moulded polythylene water storage tank Exc 500 and n exc 1000 ltrs (cylindrical/vertical with closte top) hoisted and fixed in position all as specified in SSR Part-I including providing and fixing ball brass valve high pressure with polythene float and fly nut, 20mm bore and tank nipple completeall as specified and directed. |
| 34 | Cutting chases, holes in Brick walls, Stone walls, concrete block or slab walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth all as specified and as directed. |
| 35 | S&F in repair 20mm (OD) CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches/ walls and ceiling fixed in repairs all as specified and as directed. |
| 36 | S&F in repair 25mm (OD) CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches/ walls and ceiling fixed in repairs all as specified and as directed. |
| 37 | S&F for 20mm bore GI tubing medium grade with all fittings and fixed complete to walls and ceiling or laid in floors including dismantling of old unsv pipe complete all as specified and as directed. |
| 38 | S&F in repairs 20mm bore Ball valves highpressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms) |
| 39 | S&F in repairs 25mm bore Ball valves highpressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms) |
| 40 | S&F in repair 15mm bore CP fancy type stop valves/angle cock, cast copper alloy, screwed both ends for iron pipe or for union complete all as specified and as directed. |
| 41 | S&F in repair two way 15mm bore CP fancy type angle cock, cast copper alloy, screwed both ends for iron pipe or for union complete all as specified and as directed. |
| 42 | S&F in repairs 15mm bore stop valves, angle cock, cast copper alloy, chromium plated with long shank and cup (concealed type) complete all as specified and as directed. |
| 43 | S&F in repair 15mm bore Bib taps CP fancy type, cast copper, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. |
| 44 | S&F in repair 15mm bore two way Bib taps (for health faucet/jet spray) fancy type, chromium plated, cast copper ally with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. |
| 45 | S&F in repair 15mm bore dia pipe CP wall mixer for mixing (HOT/COLD) water, with wall cap/band of CP Brass, screwed down, screwd for iron pipes 15mm bore complete all as specified and directed. |
| 46 | S&F in repair 15mm bore centre hole basin mixer fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' and `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed. |
| 47 | S&F in repair 15mm bore Brass CP sink mixer fancy type with swinging casted spout (wall mounted type) for kitchen sink screwed down for iron pipe and fixed complete all as specified and directed. |
| 48 | S&F in repairs 15mm bore pillar taps, cast copper alloy with capstan heads, chromium plated,fancy type screwed down high pressure with or without lettered “HOT” or “COLD” with long screwed shanks and fly nuts complete all as specified and as directed. |
| 49 | S&F in repair Brass chromium plated shower rose 125mm size complete all as specified and as directed. |
| 50 | S&F in repair Jet Spray (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.00 metre long flexible tube including making connections and fixed in position complete in all respect complete all as specified and directed. |
| 51 | S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect complete all as specified and as directed. |
| 52 | S&F in repair brass chromium plated Tubular towel rail 20mm dia, D type, 60cm long between flanges complete all as specified and as directed. |
| 53 | S&F in repairs Towel Ring of PTMT dia 200-215 mm fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) complete all as specified. |
| 54 | S&F in repairs chromium plated brass towel ring of heavy quality,ring dia 175-200 mm,min 8mm rod thickness approved make, complete with CP brass brackets, CP brass screws, rawl plugs and all necessary fittings and fixtures fixed firmly to wall complete all as specified and directed by Engineer-in-Charge |
| 55 | S&F in repair SS soap dish, approximate size 100x75 mm, fixed to plugs with chromium plated brass screws complete all as specified and directed. |
| 56 | S&F in repair Toilet paper holder with flat recessed type stainless steel fixed to walls with chromium plated (CP) brass screws complete all as specified and as directed. |
| 57 | S&F in repair PVC valveless flushing cistern, low level white with inlet ball valve float and handle including brackets complete fixed capacity of flush 10 ltrs complete all as specified and as directed. |
| 58 | S&F in repair 15mm bore, 450mm long, PVC connections with brass unions internally threaded both ends complete fixed to iron pipe at both ends as fixed in repairs complete all as specified and as directed.. |
| 59 | S&F in repair 15mm bore, 600mm long, PVC connections with brass unions internally threaded both ends complete fixed to iron pipe at both ends as fixed in repairs complete all as specified and as directed.. |
| 60 | S&F in repair 15mm bore PTMT Bib taps standard any colour screwed down for iron pipe and fixed minimum weight 90 gm complete all as specified and directed. Make: Prayag & equivalent. |
| 61 | S&F in repair 15mm bore pillar taps fancy type (long body) cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed. |
| 62 | S&F in repairs of 32mm Waste coupling of PTMT (half or full threaded) .(Minimum weight 32mm-45gms/40mm-60 gms.for kitchen sink complete all as specified and directed. |
| 63 | S&F in repair Grating 100mm made out of round stainless steel complete all as specified and directed. |
| 64 | S&F in repair stainless steel kitchen rack made of 0.63 mm thick stainless steel sheet of size 900 mm x 750 mm x 250 mm fixed to wall with screws complete all as specified and directed. |
| 65 | S&F in repair 32 to 40mm dia PVC waste pipe for WHB/sink/Urinal complete all as specified and as directed. |
| 66 | S&F in repair 450mmx600mm bevelled edge mirror of selected quality glass, mounted on 6mm thick PVC sheet and fixed to wooden plugs with chromium plated brass screws and cup washers, complete all as specified and as directed. |
| 67 | S&F in repair sheet glass corner wall mounted shelf assembly consisting of 5.50 mm thick sheet glass 220mmX220mm size with chromium plated bracket guard and railing 50mm high complete all as specified and as directed. |
| 68 | S&F in repairs sheet glass shelf aasembly consisting of 5.50 mm thick sheet glass shelf 120 mm wide with chromium plated bracket guard and railing of 600 mm long complete all as specified and as directed. |
| 69 | S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white including P or S trap, connection to drain (or outgoing pipe) and to flushing pipe 32mm PVC with and including plastic water closet seat, white closed pattern with flat bottom, cover and mild steel hinges device,flushing cistern of 10ltr capacity complete all as specified. |
| 70 | S&F in repairs vitreous china squatting Pan “Orissa” Pattern, of size 580mm x 440mm white with integral foot rests and trap,including flushing cistern and flush pipe, including trap and provn of cement concrete bedding complete as fixed complete all as specified. |
| 71 | S&F in repairs wash hand basins, vitreous china,of size 550x400mm (flat back, or angle back type) including cutting for and pinning in ends of brackets or erecting stand inclusive of fixing of supply and 32mm PVC waste pipe etc complete all as specified and as directed. |
| 72 | S&F in repair plastic water closet seat for pedestal/semi pedestal closet pan, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified. |
| 73 | S&F in repairs stainless steel kitchen sink with drainage board, made of stainless steel 1 mm thick, with plugs, washers and waste pipe, including bedding in cement mortar on dwarf wall or including fixing cantilever brackets and connecting union to waste pipe and 32mm dia PVC waste pipe, over all size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and as directed. |
| 74 | S&F in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe,overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. |
| 75 | S&F in repair chromium plated brass sprindle suitable for 15 mm concelled type stop cock / angle cock / Pillar tap/ Bib tap complete all as specified and directed. |
| 76 | S&F in repair mirror of approved quality and size made from 5 mm thick superior quality float glass mirror with silver backing and protective paint coating on rear side, fixed to wall with CP brass screws and washers over approved backing surface fixed in aluminium/wooden/PVC frame complete all as specified and as directed. |
| 77 | S&F in repair one piece European Water Closet (EWC) made of white vitreous china, including integral flush tank, dual flush system (3/6 litre), soft-close seat cover, S/P trap, all fittings, and fixing complete in all respects, including connection with soil pipe and testing complete all as specified and directed. |
| 78 | S&F in repair 550x450mm white vitreous china table top wash basin(oval/rectangular/round) of approved make and size including waste coupling, chromium plated brass long body sink mixer, hot and cold 450-600mm PVC braided connection pipes with fittings ,waste pipe, all necessary brackets, screws, nuts, washers and fixing accessories,angle cock as per direction of Engineer-in-Charge. |
| 79 | S&F in repair 550x450 vitreous china wash basin with pedestal,including waste coupling, chromium plated brass long body sink mixer, hot and cold 450-600mm PVC braided connection pipes with fittings ,waste pipe, all necessary brackets, screws, nuts, washers ,angle cock and fixing accessories complete in all respects as per direction of Engineer-in-Charge |
| 80 | M&L for powder coated aluminium ventilator made of aluminium extruded sections of weight 0.6-0.8kg/m and 1-2mm thick, glazed with 4mm figured glass in half portion and aluminium louvers in remaining half portion, including all cleats, rubber beading, screws, hardware and fixing arrangements complete. The item includes dismantling/taking down existing old ventilator carefully without damaging adjoining structure and making good disturbed surfaces with cement plaster complete all as specified and directed. |
| 81 | S&F in repair 20 mm gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipe and complete all as specified and directed. |
| 82 | Taking down chowkhats or frames (without taking off shutters from the frame) n. exc 1.5 Sqm incl cutting holes and making good reqd shape for hold fast block for new frame complete all as specified. |
| 83 | Taking down shutters of any description exc 1sqm but not exc 2.00 sqm each complete all as specified and as directed. |
| 84 | S & F solid PVC door frames of size 50x47mm made out of 5mm plain colour PVC sheet supplying and fixing in opening as per specification and drawing shown in SSR complete all as specified and as directed. |
| 85 | Supply and fixing Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail;Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site all specified and as directed. |
| 86 | S&F of stainless steel butt hinges of size 100 mm, with necessary stainless steel screws, complete all as specified and directed. |
| 87 | S&F for 150mm long extruded alluminium alloy handle, cast type, anodized all as specified |
| 88 | S&F for 150mm size Aluminium anodizes barrel tower bolts of extruded section complete all as specified and as directed. |
| 89 | S&F in repairs 75mm bore PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and as directed. |
| 90 | S&F in repairs PVC (SWR) bend any radius 110mm complete all as specified and directed. |
| 91 | S&F in repairs PVC (SWR) bend any radius 75mm complete all as specified and directed. |
| 92 | S&F in repairs PVC (SWR) bend any radius 110mm provided with access door complete all as specified and directed. |
| 93 | S&F in repairs PVC (SWR) bend any radius 75mm provided with access door complete all as specified and directed. |
| 94 | S&F in repairs 110 mm bore PVC [SWR] Junction single [single \\"T\\"] equal or unequal with access door complete all as specified and as directed. |
| 95 | S&F in repairs 75 mm bore PVC [SWR] Junction single [single \\"T\\"] equal or unequal with access door complete all as specified and as directed. |
| 96 | S&F in repair 110mm bore of PVC (SWR) pipes single socketed in any length with rubber ring joints laid on wall complete all as specified and as directed. |
| 97 | S&F in repair 75mm bore of PVC (SWR) pipes single socketed in any length with rubber ring joints laid on wall complete all as specified and as directed. |
| 98 | Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for |
| 99 | Demolition of stone slabs and tiles laid, bedded and pointed in any mortar of any description or thickness in floors, aprons etc complete all as specified and as as directed. |
| 100 | M & L for Granite of black / green / imperial red (colour as approved by Accepting Officer) of any type machine cut as in shelves/steps/counter tops, 18-20 mm thick, including hole set and jointed in cement slurry over & including screed of 15 mm thick / rendering in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab or with suitable adhesive for fixing on unpolished kota stone slabs and including rubbing, cutting and mirror type polishing and bull nose on exposed sides complete all as specified .Note : Single piece should be used in steps/cills/jambs/shelves or equivalent as approved by accepting officer . |
| 101 | M&L for Kota stone slab 18-20mm thick (in single piece as vertical support and horizointal base for granite top) laid over in cooking platform,counter top, jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete complete all as specified and as directed. |
| 102 | S&F in repairs of Factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite ) Plain Board of required size with stainless steel ISI marked fittings as 75mm/100mm ss fancy handles (01 No in each shutter ), with 35mm stainless Steel auto cup hinges (if shutter height 600mm-2 hinges,600-900mm-3 hinges,900-1200mm-4 hinges) with necessary full body threaded star headed counter sunk SS Screws comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural Fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with density not less than 650 kg/cbm , having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N (Edge ), Minimum Compressive Strength of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof, Fire Retardant and fixing .All as per direction of Engineer -In-Charge. For WC/Bathroom/Toilet/Kitchen/Balcony Doors & Cabinets. |
| 103 | S&F in repair 6 mm thick WPC (Wood Polymer Composite) board of approved make and shade as back panel of cupboards/cabinets, fixed in grooves or with suitable screws, including cutting, edge finishing, necessary supports, fixtures and fasteners,all specifications will be match above item no. complete all as specified and directed. |
| 104 | S & F in repair Perforated Cutlery Basket with 4mm dia 100 % stainless steel, non - magnatic, multilayer chrome plated, argon welded, double sealed ball bearing mechanism capable of holding plates, cup, saucers, bowls and dongas with 420x485x100 mm of carcass complete all as specified & directed by Engineer -in -Charge. Make : Prod code No. 6133 of Godrej or equivalent make in Hettich/Lifetime |
| 105 | S & F in repair Thali-Plate Basket baskets with 4mm dia 100 % stainless steel, non - magnatic, multilayer chrome plated, argon welded, double sealed ball bearing mechanism capable of holding plates, cup, saucers, bowls and dongas with 420x485x200 mm of carcass complete all as specified & directed by Engineer -in -Charge. Make : Prod code No. 6138 of Godrej or equivalent make in Hettich/Lifetime |
| 106 | S & F in repair Cup and saucer Basket baskets with 4mm dia 100 % stainless steel, non - magnatic, multilayer chrome plated, argon welded, double sealed ball bearing mechanism capable of holding plates, cup, saucers, bowls and dongas with 420x485x200 mm of carcass complete all as specified & directed by Engineer -in -Charge. Make : Prod code No. 6158 of Godrej or equivalent make in Hettich/Lifetime |
| 107 | S&F in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire stapples of any type of windows and doors i.e. wooden, steel or aluminium including opening and refixing of frame, shutter or shutter elements if required and new wooden beads in wooden doors, complete all as specified and as directed. and directed. |
| 108 | Hacking out old broken glass [any thickness, size, quality or description] from metal frames including punching or drilling out old glazing pins / spring clips complete all as specified and as directed. |
| 109 | S&F for sheet glass 3mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sq.m in each pane complete all as specified and as directed. |
| 110 | S&F for sheet glass 3mm thick, ordinary quality and glazing with oil putty in squares exceeding 0.5 Sq.m in each pane complete all as specified and as directed. |
| 111 | S&F for 3mm thick figured glass, pin head type and glazing with putty in square not exceeding 0.50 Sqm in each pane complete all as specified and as directed. |
| 112 | S&F for 3mm thick figured glass, pin head type and glazing with putty in square exceeding 0.50 Sqm in each pane complete all as specified and as directed. Please Enable Macros to View BoQ information |
