|
| 1 | PART-A (Bldg.) |
| 2 | P-2.10: Development of tube well having depth upto 250 mtr as per IS:11189-1985 and IS: 2800 (Part-I) - 1991 (both amended up to date ) using suitable methods to give sand free water for required yield of the gravel packed tube well. |
| 3 | P-2.7.1 : Deepening of existing tubewell by DTH system beyond existing depth up to 100 mtr and above in all type of rocks including flushing of tubewell and obtaining sand free water nominal bore 150 mm dia. |
| 4 | P-2.12 : Labour charg for making slots on blank pipes made of ERW M.S. black casing pipe ISI marked of following sizes, the sloting should be as per IS : 8100/1985: P-2.12.3 : 200 mm dia nominal bore of 5.4 mm thickness (P-2.12.3) |
| 5 | P-2.22 : S & F M.S. clamp set of 50 ×6mm flat iron with nuts and bolts etc. for holding the riser pipe assembly of submersible pump set. |
| 6 | S-4.8.4 : S & F tube well cover of M.S.sheet (6mm thick) with nuts and bolts complete for casing size: 200mm dia |
| 7 | S-2/2.26+2.27.1 : P & F PVC Storage Tank ISI Marked (IS : 12701) indicating the BIS license No), of approved make with cover, 25mm dia 1M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design including Hoisting Charges for first floor : 500 litres capacity. (S-2.26.3+2.27.1) |
| 8 | S-2/2.39: Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (IS 15778 : 2007 code) having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings, this included jointing of pipes & fittings with one step CPVC solvent cement , trenching refilling & testing of joints complete as per direction of Engineer in Charge.(External work).S-2/2.39.2: 20mm nominal size |
| 9 | S-2/2.39.3: 25mm nominal size |
| 10 | S-2/2.15 : P & F Full-way Valve (IS:778 Mark) or wheel valve of approved make ::(a)Gun-metal 15mm nominal bore (S-2.15.1) |
| 11 | (b)Gun-metal 25mm nominal bore (S-2.15.3) |
| 12 | PART-B (Electrical Work) |
| 13 | E-21.1 : Labour charges for installation of submersible motor pump set including lowering/ delowering of pipes, cables, accessories etc. in tube-well/ open well complete including T&P, transportation of tripod, chain pulley block & any other material required for this purpose complete in all respect. (a) E-21.1.2 :Delowering only |
| 14 | (b) E-21.1.3 :Delowering and Lowering |
| 15 | E-21.3.1: Providing & Laying of Polypropylene rope Confirming to IS:5175 for submersible pump of following sizes. complete in all respect. :12mm (suitable up to 50 mm OD pipe) |
| 16 | E-21.4.1.1 : Providing & Fixing of HDPE pipe Confirming to IS:4984:2021 for water supply suitable for submersible & jet pump with required fittings ie socket, elbows, tee etc. complete in all respect.: for vertical installation: 40 mm OD 6 kg / cm2 |
| 17 | E-4.7.4 : Supply and Laying ISI marked P.V.C. insulated submersible cable confirming to(IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from copper, stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, existing pipe / open trench / Cable tray / on surface including making connection etc. as required. (6.0 Sq.mm 3 core flat / Round) |
| 18 | E-21.13.1.2: SITC of Contactor OEM Fabricated DOL/Star-Delta Starter panel with switchgear selection as per Type-2 Cordinatiom Chart and made out from 1.6 mm thick powder coated CRCA sheet, enclosure comprising of over load protection relay, short circuit & single phasing protection, Illuminated ON / OFF push buttons, ammeter, voltmeter, indicating lamps etc. suitable for following rating motors complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR .(a) For single phase Submersible / Monoblock pump : 2.0 HP to 3.0 HP (DOL starter) |
| 19 | E-21.6.1 : SITC of Radial / mixed flow water and anti-corrosive liquid filled submersible motor pump sets suitable for 100/150mm dia borewell. The size of adopter fixed on top of the motor should exceed the top of coupler , for safegaurd the coupler. The job includes labour part of lowering of riser pipe G.I./ H.D.P.E. with rope, cables & pump, installation of complete fitting and accessories, jointing of electrical cables up to Starter. All labour for testing of submersible pumps set and supply of water to water mains, complete in all respect.(a)(E-21.6.1.3) 2.0 HP, 1-Ø, (7- 95)Mtr, (55-22) LPM |
| 20 | (b)(E-21.6.1.4) 3.0 HP, 1-Ø, (40 -170)Mtr, (60- 20) LPM Copper Wound |
| 21 | (c)(E-21.6.1.5) 5.0 HP, 1-Ø, (56 - 236)Mtr, (90 - 25) LPM Copper wound |
| 22 | E-26.74.2 : Rewinding of single phase/3phase submersible motor including all necessary material and of the same characteristics as original with required size of super enamelled wire 'E' class insulation material and testing etc. as required. Replacement of material or components shall be use as per guidelines of OEM of original product. All the scrap material should be retained by the contractor..: 2.0 H.P.to 3.0 HP |
| 23 | E-26.75.2 :Repairing of submersible pump of with replacement of broken impellers ,diffuser,bush/bearing set , oil seal complete with testing etc. as required. Replacement of material or components shall be use as per guidelines of OEM of original product. All the scrap material should be retained by the contractor..: 2.0 H.P.to 3.0 HP |
| 24 | E-21/21.2.2.1: Supply & fixing of PVC threaded casing pipes for Tube well (IS 12818:1992) as required.: more than 400 ft to 1200 ft. Depth: 40mm dia |
| 25 | PART- B (Item Rate Basis) |
| 26 | Repair of pannel board for submersible pump installed at various JPD premises including changing/repairing of Capacitor/Voltmeter/ammeter/relay/indicating lamps for start and run position/ any part to make pannel board in working condition complete in all respect as per directions of Engineer in Charge. The job also includes warranty of pannel board upto maturity of SD work including frieght charges of parts with mechanics upto shop required if repairing of panel board within warranty preiod 1.0 HP to 3.0 HP (Single Phase) Please Enable Macros to View BoQ information |
