Tender For Periodical Services To External And Internal Surfaces To Otm And Md Accn Bldgs At Malad, Kandivali And Marve Under Ge (N) Santacruz Mumbai
Tender Value
30 Lakhs
Estimated cost
Bid Submission
17 Jul 2026
9 days left
EMD
60000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Mumbai Suburban → Maharashtra
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Periodical Services To External And Internal Surfaces To Otm And Md Accn Bldgs At Malad, Kandivali And Marve Under Ge (N) Santacruz Mumbai
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of reinforced cement concrete of any description, in any position, not otherwise specifically provided, for wall (reinforcement cut as required to facilitate demolition) and removing concrete debris and depositing outside MD land all as specified and as directed by Engineer-in-Charge. |
| 2 | Supply and fix mild steel TMT bars, 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.Note: Cutting of rusted reinforcement & welding shall be inclusive in this item of work |
| 3 | Supply and fix mild steel TMT bars, 5 to 10mm dia in stirrups, spacers and binder, cut to length bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.Note: Cutting of rusted reinforcement & welding shall be inclusive in this item of work |
| 4 | Material and Labour for reinforced cement concrete (Nominal mix) 1:1.5:3, using 20mm graded stone aggregates as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs, chajja, shelves and like complete all as specified and directed by Engineer-in-Charge. |
| 5 | Material and labour for formwork using steel shutters or 12mm marine ply to have the smooth finish to pour the micro concrete/ concrete including de-shuttering etc complete all as specified and as directed by Engineer-in-Charge. |
| 6 | Material & labour for repairing of damaged concrete portion by using superfluid dual shrinkage compensated structural grade M-40 micro concrete of at all levels with all leads and lift as directed including mixing, laying, levelling, finishing and curing along with MS/TS dowel pins at all heights using scaffoldings complete all as specified and directed by Engineer-in-Charge including following all process with material :- (a) Material and labour for providing and applying rust cleaner of approved make over prepared reinforcement, including removing concrete all around reinforcement including from behind the reinforcing bars by manual methods such as hammering the rebar, using wire brushes, chiseling, etc. and applying rust removing solution of approved make with cotton waste swab to reinforcements etc (b) Providing and applying two coat of anticorrosive epoxy phenolic rebar protective system to existing as well as new reinforcement (c) Priming cum bonding coat of two component peroxide resin confirms to ASTM-C-882-91 including providing and inserting 10 mm mild steel shear key bars (minimum 3 nos per sqm), shear key fixing with drilling and epoxy grout wherever required, Scaffolding at any height & mixing, laying, levelling and finishing including curing and work shall be execute as per manufacturer instruction and from authorised applicator complete all as specified and as directed by Engineer-in-Charge.Note : All materials should be approved make such as Dr Fixit, Fosroc, Sika, Krishna conchem or equivalent. |
| 7 | Material and labour for providing and laying 20 mm thick POLYMER MODIFIED MORTAR over identified R.C.C. members in One layer in proportion as per approved make, blended to a required consistency and applying and finishing by floating, curing after initial setting time, including providing and inserting 10 mm mild steel shear key bars (minimum 3 nos per sqm), wherever required, bonding slurry, etc complete all as specified and as directed by Engineer-in-Charge.Make- Dr FIXIT/ FOSROC/ Krishna Conchem/BASF/Sika as approved by GENote for Item No.1 to 7:- (i) The work under Item No. 1 to 7 shall be carried out by authorised applicator only.(ii) Defect liability for these items shall be 5 years from certified date of completion.(iii) Amount of 5% of these items shall be retained during RAR and FB. This amount shall be released after successful completion of Defects liability period as mentioned above.(iv) Non destructive testing shall be got carried out through IIT / NIT / College of Engineering Pune to decide fulfillment of fitness criteria of structure. (v) The test shall be carried out at each discrete location or locations decided by GE or testing authority. (vi)The cost of testing shall be deemed to be included in the rate quoted by the contractor. Completion shall be issued by GE after only getting structural stability certificate of each respective building from testing authority. . |
| 8 | Taking down cement plaster of any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc and removing debris outside MD land complete all as specified and as directed by Engineer-in-Charge |
| 9 | Material and labour for rendering 10mm thick on internal wall surfaces using factory manufactured pre mix/ready mix plaster of 'Roofit Mix' of M/s Premier Floor to Roof Materials Pvt Ltd/'Easy plast' of M/s Walplast Products Pvt Ltd/'Readiplast' of M/s Ultratech Cement Ltd' / Sound last PMC-1 of M/s Sound buildcare Pvt Ltd/or other approved equivalent make, having minimum composition of C:S : 1:3 using fully treated dry, well graded natural sand conforming to IS 383 suitable for plastering, having low rebound properties, low water demand for curing properties, mechanical mixing with water in a metallic tray only to make good consistency as per the specification of the Manufacturer and applied over masonry and concrete surfaces and finishing with sagol finish not less than 1mm thick, including cleaning the surfaces, curing etc complete all as specified & directed by Engineer-in-Charge. |
| 10 | Material and labour for rendering 5 mm thick on ceiling using factory manufactured pre mix/ready mix plaster of 'Roofit Mix' of M/s Premier Floor to Roof Materials Pvt Ltd/'Easy plast' of M/s Walplast Products Pvt Ltd/'Readiplast' of M/s Ultratech Cement Ltd' / Sound last PMC-1 of M/s Sound build care Pvt Ltd/or other approved equivalent make, having minimum composition of C:S : 1:3 using fully treated dry, well graded natural sand confirming to IS 383 suitable for plastering in ceiling, having low rebound properties, low water demand for curing properties, mechanical mixing with water in a metallic tray only to make good consistency as per the specification of the Manufacturer and applied over concrete surfaces and finishing with sagol finish not less than 1mm thick, including cleaning the surfaces, curing etc complete all as specified & directed by Engineer-in-Charge. |
| 11 | Material and labour for rendering 15 mm thick cement plaster (incl. dubbing out) in CM 1:4, two coats using factory manufactured pre mix/ready mix of 'Roofit Mix'of M/s Premier Floor to Roof Materials pvt.ltd/ 'Easy plast' of M/s Walplast Products pvt.ltd/ 'Readiplast' of M/s Ultratech Cement Ltd/'Soundplast PMC-1' of M/s Sound buildcare pvt.Ltd/ or other approved equivalent make, having minimum composition of C:S : 1:4 using fully treated dry, well graded natural sand conforming to IS 383 suitable for external plastering, having low rebound properties, low water demand for curing properties, mechnIcal mixing with water in a metalic tray only to make good consistency as per the specification of the Manufacturer and applied over exterior masonry and concrete surfaces with base coat of 10 mm thick and finishing coat of 5 mm thick final rendering with water proofing compound @3% as per manufacturer's instructions, including using richer mix for making corners if necessary, at all floors and level, including making grooves of existing size wherever required,inclding sagol finish including cleaning the surfaces, curing including provide of 150mm chicken wire mesh fixed with nails at the junction of RCC columns/walls/ beams/ lintels and brick masonry at external faces before plastering including scaffolding at any height and all safety materials required for execute work etc. complete all as per specifications & as directed by the Engineer-in-Charge. |
| 12 | Material and labour for preparation of newly plastered wall surfaces and applying two coats of oil bound distemper with roller over a coat of alkali resistant wall primer complete all as specified and directed by Engineer in Charge. Make: Asian Paints (Tractor) / Nerolac Paints /Jenson & NIcholson / Shalimar Paints / Birla Opus Paints |
| 13 | Material and labour for preparation of newly plastered ceiling surfaces and applying two coats of oil bound distemper with roller over a coat of alkali resistant wall primer complete all as specified and directed by Engineer in Charge. Make: Asian Paints (Tractor) / Nerolac Paints /Jenson & NIcholson / Shalimar Paints / Birla Opus Paints |
| 14 | Material and labour for preparation of new plastered wall surface and applying two coats of Acrylic weather proof coat 100% exterior grade paint over one coat of acrylic primer upto a height of bldg roof including formwork/scaffolding/ladders and safety belts with precautions etc complete all as specified and as directed by Engineer-in-Charge.Make : APEX ULTIMA” of Asian Paints/ “WEATHER COAT ALL GUARD” of Berger Paints/\\"EXCEL TOP GUARD” of Nerolac/ “DULUX WEATHERSHIELD MAX” of ICI India/Birla Opus Paints ( Brand- One True life) |
| 15 | Material and labour for complete removal of existing treatment on wall surfaces by scrapping with steel wire brush and scrappinng down all smoke soots, molds, moss and efflorescence on wall by scrubber and applying two coats of distemper oil emulsion with roller over a coat of alkali resistant wall primer complete all as specified and directed by Engineer in ChargeMake: M/s SHALIMAR / M/s BERGER / M/s NEROLAC /M/s ASIAN (Tractor Brand)/Birla Opus Paint |
| 16 | Material and labour for complete removal of existing treatment on ceiling surfaces by scrapping with steel wire brush and scrappinng down all smoke soots, molds, moss and efflorescence on wall by scrubber and applying two coats of distemper oil emulsion with roller over a coat of alkali resistant wall primer complete all as specified and directed by Engineer in ChargeMake: M/s SHALIMAR / M/s BERGER / M/s NEROLAC /M/s ASIAN (Tractor Brand)/\\"Birla Opus Paints\\" |
| 17 | Material and labour for complete removal of existing treatment on wall surfaces and applying two coats of Acrylic weather proof coat 100% exterior grade paint over one coat of acrylic primer upto a height of bldg roof including formwork/scaffolding/ladders and safety belts with precautions etc complete all as specified and as directed by Engineer-in-Charge.Make : APEX ULTIMA” of Asian Paints/ “WEATHER COAT ALL GUARD” of Berger Paints/\\"EXCEL TOP GUARD” of Nerolac/ “DULUX WEATHERSHIELD MAX” of ICI India/Birla Opus Paints ( Brand- One True life) |
| 18 | Material and labour for complete removal of existing treatment like moulds, dry algae, existing paint, termite damage, scraches and any other of external wall surfaces of building, boundary wall, jafri wall and any other structures and applying two coats of cement base paint over a coat of primer complete all as specified and as directed by Engineer- in-Charge. Make: Super snowcem/Duracem/Aquacem/Shalimar/Berger/ Permacem/Birla opus |
| 19 | Material and labour for preparation of wall surfaces and applying 1.5 mm thick wall care putty complete to smoothen the underneath surfaces complete all as specified and as directed by Engineer-in-Charge.Make: Asian Paints / Nerolac Paints /Jenson & Nicholson / Shalimar Paints / JK wall care putty/ Birla Opus Paints |
| 20 | Material and labour for preparation of ceiling surfaces and applying 1.5mm thick wall care putty complete to smoothen the underneath surfaces complete all as specified and as directed by Engineer-in-Charge.Make: Asian Paints / Nerolac Paints /Jenson & Nicholson / Shalimar Paints / JK wall care putty/ Birla Opus Paints Please Enable Macros to View BoQ information |
| 21 | Material and labour for preparation of ceiling surfaces and applying 1.5mm thick wall care putty complete to smoothen the underneath surfaces complete all as specified and as directed by Engineer-in-Charge.Make: Asian Paints / Nerolac Paints /Jenson & Nicholson / Shalimar Paints / JK wall care putty/ Birla Opus Paints Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jun 26, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 17, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 9 daysJul 20, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 12 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender