|
| 1 | M&L for Vitrified tiles 10 mm thick, in (Square/rectangular) polished, area of each tile not exceeding 0.36 sqm, in floors etc. set & jointed in neat cement slurry and pointed in coloured cement to match incl dismantling / demolition , coloured tiles laid over and including 15 mm thick screed bed or bedding layer in Cement motar 1:6 complete all as specfied and directed. |
| 2 | M&L for Vitriefied tiles 10mm thick square/rectangular) polished area of each tiles not exceeding 0.36 sqm as in vertical surfaces such as dados/skirting etc set and jointed in neat cement slury and in coloured cement to match incl dismantling / demolition, coloured on incl plaster (backing coat) 1:4 Cement motar 10mm thick layer in Cement motar complete all as specfied and directed. |
| 3 | M&L for glazed ceramic coloured tiles of size 450mm x 300mm x 7mm thick verticale tiles with highlighter any colour on vertical surface such as skirting, dados, risers to steps etc set & jointed in neat cement slurry and pointed in white or coloured cement to match incl dismantling / demolition and colour of tiles, incl dismantling / demolition over and including rendering 10mm thick in cement mortar (1:4) , complete all as specified and directed. |
| 4 | M&L for coloured non skid ceramic tiles, 7 to 8 mm thick, (square/rectangular), area of each tile exceeding 0.06 sq.m but not exceeding 0.11 sq.m in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match i incl dismantling / demolition and rubbish off the primises etc over ,screed bed or bedding layer of 15 mm thick cement mortar (1:6) complete all as specified and directed. |
| 5 | M&L 25 mm thick cement concrete type B-0, 1:2:4 using 12.5mm graded stone aggregate as in leveling cource complete all as specified as directed. |
| 6 | Demolition of cement concrete (un-reinforced) in ground floor and paving n. exc 15 cm thick below or above ground level & dispose off debris upto a distance n. exc. 100 mtrs where directed complete all as specified and directed. |
| 7 | S&F, in repairs, 20 mm thick, PVC sheet one side prelaminated of approved texture (\\"Celuca Ply of Rajshree make or equivalent in as approved by GE) as in Kitchen cabinet complete all as specified and directed.(Note:- Each member i.e. shelf, partition & shutter of kitchen cabinet shall be measured and paid separately) |
| 8 | S&F stainless steel kitchen basket in various type of basket , plaint basket height , 4\\" Thali basket 8\\" height Cup saucer 4\\" heigt and perforated cutlury basket 4\\" height all as specified and directed. |
| 9 | S&F telescopic chennel for basket sizes 46mm wide all as specified and directed |
| 10 | S&F stainless steel handle for basket size 6\\" all as specified and directed |
| 11 | Supplying, Hoisting and fixing in repairs 500 litres capacity rotational moulded polyethylene water storage tank (cylindrical, vertical with closed top) & fixing arrangement for inlet/outlet/over flow and vent pipe of standard size including taking down old water storage tank all as specified in SSR Part-I including 20mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed. |
| 12 | Supplying, Hoisting and fixing in repairs 1000 litres capacity rotational moulded polyethylene water storage tank (cylindrical, vertical with closed top) & fixing arrangement for inlet/outlet/over flow and vent pipe of standard size including taking down old water storage tank all as specified in SSR Part-I including 20mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed. |
| 13 | Dismantling brick tiles or terracing single layer as in roofing complete all as specified and directed. |
| 14 | Demolition of mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) complete all as specified and directed. |
| 15 | M&L for 50 mm average thickness PCC 1:2:4 type B1 (using 20 mm graded stone aggregate as roof padding, for further treatment complete all as specified and directed. |
| 16 | M&L for preparation of roof surface & applying evenly a tack coat of industrial bitumen primer 85/25 grade @ 1.2 Kg/Sqm including APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3 mm thick reinforced wih polyster non wove fabric (wt not less than 150 gms/sqm) applied on primed surface by forced application of heat and roller, joints to be touched hot and width of overlaps not be less than 150 mm complete all as specified and directed. |
| 17 | M&L, 40 mm thick brick tiles laid and joints in cement mortar (1:3) over 25 mm thick screed bed in cement morter 1:4 and flush pointing as work proceed complete all as specified and directed. |
| 18 | All as per Ser Item No 18 above, but except bricks tiles complete all as specified and directed. |
| 19 | M&L for raking out joints/ pointing to brick work built in cement mortar as in walls or to bricks on edge in floors, surface channels, roofs, etc. complete all as spd and as directed. |
| 20 | M&L for flush pointing to brick wall in cement mortar 1:3 complete all as specified and directed. |
| 21 | Roughening surfaces of old concrete floor/terrace by picking incl. taking down existing detoriated / decayed tar felt PCC tiles or any type of treatment including loose surface, scraping with scraper, chiseling, scraping of surface with wire brush or any other method, sweeping clean & washing down with water to remove dust etc. and removing the scraped materials debris to a distance not exc. 50 m. |
| 22 | M&L of 25mm plain Cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) as in levelling course including dismantiling of old PCC complete all as spd |
| 23 | M&L for applying two coat of undiluted thick coat of acrlic reinforcement liquid applied elastorneric water proofing membrane with UV resistance properties and solar refective properties over one coat of primer (1:3, Dilution:water) Note: Every each coat gap between 6 hrs) complete all as specified and directed. |
| 24 | Disconnecting, setting aside (or lowering if required) and Cleaning & removing all scale and dirt etc from HDPE water tanks of 500 litres capacity (Tanks placed on top of roof) and from mouths of circulating pipes etc including washing the tank with bleaching powder and hoisting, reconnecting and re-fixing in position including writing the date of cleaning of tank with synthetic enamel (black/white) paint of size not less than 10cm of each letter complete, all as specified and directed. |
| 25 | Disconnecting, setting aside (or lowering if required) and Cleaning & removing all scale and dirt etc from HDPE water tanks of 1000 litres capacity (Tanks placed on top of roof) and from mouths of circulating pipes etc including washing the tank with bleaching powder and hoisting, reconnecting and re-fixing in position including writing the date of cleaning of tank with synthetic enamel (black/white) paint of size not less than 10cm of each letter complete, all as specified and directed. |
| 26 | S&F 15mm bore tubing medium grade galvanised steel tubing with all fittings and fixed to walls, ceiling and in floor incl cutting, chasing in wall, floor or ceiling and making goodin CM 1:3 incl taking down old pipe complete all as specified and directed. |
| 27 | S&F 20 mm bore tubing medium grade galvanised steel tubing with all fittings and fixed to walls, ceiling and in floor incl cutting, chasing in wall, floor or ceiling incl taking down old pipe complete all as specified and directed. |
| 28 | S&F, in repair, central hole basin mixer with extended spout 300 mm long braided connection pipe (without popup) for iron pipe or for unions and fixed to 15mm bore pipe complete all as specified and directed. |
| 29 | Supply & fix in repair, 15 mm bore single lever Sink mixer complete all as specified and directed. |
| 30 | S&F in repair 15mm bore dia fancy type chromium plated long body bib tap with crutch or buttewrfly handle screwed down to iron pipe with all fittings complete all as specified and directed. |
| 31 | S&F in repair 15 bore dia chromium plated Stop cock/Angle cock screwed down high pressure with crutch or butterfly handle & screw both end for iron pipe or for unions complete all as specified and directed. |
| 32 | S&F in repairs, stop valves, concealed type cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and directed for 15mm bore of pipe. |
| 33 | S&F in repairs, hand shower sizes 65x95mm rectangular shape singel flow with rubite cleaning system face plate stainless steel and ABS body in chrome finished ) with 1.5 meter long flexible tube with nut and premium wall braket for hand shower 35mm dia and 100mm long round shape complete all as specified and directed. |
| 34 | S&F, in repair Health Faucet/hand shower with 8mm dia 1mtr long easy flexible tube with chrome finish & wall hook complete all as spd and directed. |
| 35 | S&F, in repair, chromium plated glass corner (Corse) size 300mmx300mm complete all as specified and directed. |
| 36 | S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified. |
| 37 | S&F in repair, brass chromium plated single lever wall mixer 3-in-1 system with provision of both over head shower with 115 mm long bend pipe connecting legs and wall flange (wihout head shower) complete all as specified and directed. |
| 38 | S&F in repairs, brass chromium plated single lever wall mixer 4 in 1 system with provision of both over head shower and hand shower with 115 mm long bend pipe connecting legs and wall flange (wihout hand and over head shower |
| 39 | S&F in repair viterous chinaware wash hand basin light colour/white of size 550x 400cm flat back or angle stay, brass chromium plated waste coupling, chain, plug, porcelain rubber stopper, brackets,32mm bore PVC waste pipe of appropriate length complete all as specified and directed |
| 40 | S&F in repair vitreous china ware counter ovel wash hand basin, any colour, size 570 x 450 mm size fixing in slab including fixing waste pipe , CP waste coupling all as specified. |
| 41 | S&F in repair for viterous china wash down water closet pan (pedestal pattern) coloured including 'P' or 'S' trap with flush pipe of chromium plated brass 32 mm dia for low level flushing cistern incl plastic seat cover white closed pattern with float bottom and cover and jet connection and mild steel chrominum plate or aluminized hanging device fixed in repairs complete all as specified and directed. |
| 42 | S&F, in repair, vitreous china floor mounted single piece WC with dule flush cisteren PP soft close seat cover , hinges accessories set as per size 390x610x800mm with cistern fitting (including fixing bolts flush pipe) complete all as specified and directed. |
| 43 | S&F in repair 32mm bore Brass chromium plates bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap complete all as specified as directed. |
| 44 | S&F in repair 10 ltrs capacity PVC valveless. Syphonic action type, flushing cistern, low level, with inlet, ball valve, float, and handle and brackets including 32mm dia flush pipe of polyethylene of high density for low level cistern complete all as specified and directed. |
| 45 | Taking down old shutters of any description exc. 1.0sqm but not exc. 2.0sqm each complete all as specified and directed. |
| 46 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5sq.m each complete all as specified and directed. |
| 47 | Taking down chowkats or frames with shutters (without taking off shutter from the frames) exc. 1.5sq.m but not exc. 4sq.m each complete all as specified and directed. |
| 48 | Material and labour for 30 mm thick factory made solid (Wood polymer composite) moulded gauged door shutter with wire mesh in any number of division with brown wood grain texture, including S.S wire mesh shall be fixed l zink coated screws can be remove or fix again after changing of wire mesh when needed. The density shall be as per manufactures instructions complete all as specified and directed. |
| 49 | S&F, 35 mm thick, 2nd class hard wood, glazed & skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. Sizes of members of shutters as specified in SSR Part I, Section 8, Clause 8.24 (a) complete all as specified and directed. |
| 50 | S&F for 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. |
| 51 | S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent ement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, all as per manufacturer's instruction complete all as specified all as specified. |
| 52 | M&L Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction.(Note: stainless steel butt hinges and necessary S.S screws shall be paid separately |
| 53 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door frames/ Chowkhat of size 50x100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant including making good after complete all as speicifed and directed. |
| 54 | All as per item No 54 above but of frame size 65 x 125 mm including all fittings making good after complete all as speicifed and directed. |
| 55 | S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying and fixing in opening as per specifications complete all as specified and directed. |
| 56 | S&F, aluminium anodised, barrel tower bolts of extruded section with length of bolt 150 mm and fixed complete all as specified and directed |
| 57 | S&F, stainless steel butt hinges, of size 100 mm complete all as specified and directed. |
| 58 | S&F extruded aluminium alloy handles, fabricated type, anodised of size 150 mm complete all as specified and directed. |
| 59 | S&F 300mm mild steel ordinary rat tail rod pattern spring incl roller plate complete all as specified and directed. |
| 60 | S&F, aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy with length of bolt 300mm and fixed complete all as specified and directed. |
| 61 | S&F, in repair, Mortice lock, mild steel, four lever, verticle type, size 100mm complete all as specified and directed. |
| 62 | S&F, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 63 | S&F, in repair, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 64 | S&F, in repair, 25 mm dia, 1 mm wall thickness stainless steel fancy type, decorative curtain rod with decorative ball type side brackets (As per Sample) fix with wooden gutties complete all as specified and directed. |
| 65 | S&F anodised aluminium powder coated any colour minimum coating 50 micron three track windows/ventilators with one or more rebates including joining cleat for fixing etc complete with frame and shutter of fixing with handles, tower bolts, rubber gasket and maruti lock, and making good to disturbed surface with cement concrete 1:2:4 and cement mortar 1:4 complete all as specified and directed. |
| 66 | S&F for anodised aluminium powder coated door shutters, aluminium section weighting 0.55kg/m, incl necessary 5.00 mm thick, black tinted glass panes with nano coating & glazing or PVC sheet joining with cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, handles, lock , 2 x aluminium handles 150mm, 3 x hinges, 2 x Aluminium tower bolts 150mm with each shutter of any type complete all as specified all as specified. |
| 67 | S&F anodised aluminium powder coated window and ventilator shutters, sliding/side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary 5.00 mm thick sheet glass ordinary quality & glazing, aluminium joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.), hinges type B-21 100mm long (2 no.) suitable handle (1 no.), rollers etc and making good to disturbed surface with cement mortar in 1:4 complete all as specified all as specified. |
| 68 | S&F in repair Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 69 | S&F in repair for 3mm thick, sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.5 Sqm in each pane fixed with oil putty or beads and incl hacking out glass old complete all as specified and directed. |
| 70 | Demolition of stone slabs and tiles of any description or thickness in floors aprons etc laid dry or laid dry and pointed all as specified and directed. |
| 71 | M&L for Granite 18-20 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, wash basin platform, treads, risers and like laid in cement 10 mm thick cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite rounding to edges of granite stone slabs one edge such as in counter type WHB platform etc. incl dismantling / demolition and rubbish off the primises etc complete all as specified and directed. |
| 72 | S&F in repair, 600mm x 450mm plain edge mirror of selected quality glass not less than 5 mm thick, mounted on wall fixed with stainless steel stud any size complete all as specified and directed. |
| 73 | S&F PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed. |
| 74 | S&F in repair PVC waste pipe 32mm bore of size and 900mm long complete all as specified and directed. |
| 75 | S&F, in repair chromium plated tubular towel rail 20mm dia 600mm long Complete all as specified and directed.. |
| 76 | S&F, in repairs, brass, chromium plated tubular towel rack 20mm dia 60cm long between flanges, 300mm vide with hooks complete all as specifed and directed. |
| 77 | S&F in repair continuous (Piano) Hinges mild steel,bright finish or electro galvanised width of flap (when open) 30 mm complete all as specified and directed. |
| 78 | S&F in repair satinless steel magnetic catcher complete all as specified and directed. |
| 79 | S&F in repair Door seal 4mm wide with Fibre Brush and metalic body complete all as specified and directed. |
| 80 | S&F in repair only 75 mm waste fittings, brass chromium plated for sink, basins, etc. with long screw shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed. |
| 81 | S&F in repair 110 mm, waste fittings, brass chromium plated for sink, basins, etc. with long screw shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed. |
| 82 | Maintenance and overhauling of Steel rolling shutters (without taking down) opening size 2 to 16 Sqm by opening the top hood and cleaning, oiling, greasing and making free flow of shutters on its guide channels complete including cleaning, oiling, greasing of gear assembly all as directed and including two coats of synthetic enamel paint after preparatiopn of old surfaces complete all as specified and directed. |
| 83 | S&F, in repair, Steel rolling shutters, thickness of laths 1mm thick, with out ball bearing, as specified including top cover, an-choring rod, hasp and staple including one shop coat of primer, and erected in position as indicated, push pull or manual type complete all as specified and directed. |
| 84 | Taking down steel gate exc 6 Sqm but n.exc 12 Sqm any weight and refixing the same opening on bearing after repairing , painting of gate and making good distrurbed portion complete all as specified |
| 85 | S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour profile AZ-150 with side lap as in roof covering/ cladding to wall, fixed with 'L 'or 'J' hooks / self tapping screws and incl dismantling of plain or corrugated steel sheeting in roof covering all as specified and directed. |
| 86 | S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or trenches ,110 mm bore incl taking down old pipe complete all as specified and directed. |
| 87 | S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or trenches,75 mm bore incl taking down old pipe complete all as specified and directed. |
| 88 | S&F, 75mm bore PVC (SWR) bend, any radius with access door complete all as specified and directed. |
| 89 | S&F, 110mm bore PVC (SWR) bend, any radius with access door complete all as specified and directed. |
| 90 | S&F, 75mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door complete all as specified and directed. |
| 91 | S&F, 110mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door complete all as specified and directed. |
| 92 | S&F 110 mm bore PVC (SWR) vent cowl complete all as specified and directed. |
| 93 | S&F PVC (SWR) gully trap 125 x 110 mm setting and jointing with solvent cement complete all as specified Please Enable Macros to View BoQ information |
