|
| 1 | Excavating trenches by mechanical / manual means of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as per direction of Engineer-in-charge, within a lead of 50 m - all kinds of soil - pipes,cables etc , exceeding 80mm dia but not exceeding 300 mm dia |
| 2 | Providing and fixing G.I.pipes complete with G.I.fittings including trenching and refilling etc.- External work -80mm dia nominal bore |
| 3 | Providing and fixing C.I. sluice valve (PN 1.6) (withhandwheel) conforming to IS 14846 and ISI marked, with bolts, nuts, rubber insertion etc.,complete (the tail pieces if required will be paid separately) - 80 mm dia. |
| 4 | Providing and fixing C.I. Ball type non return valve (PN 1) conforming to IS 318 & IS 1363, with bolts, nuts, rubber insertion etc.,complete - 80 mm dia. |
| 5 | Providing and fixing Cast iron flanges conforming to IS specification 1538 and ISI marked. - 80 mm dia. |
| 6 | Providing and fixing in position G.I. bend conforming to IS 1239 part II and ISI marked,including labour charges for jointing,jointing materials etc,complete - 80 mm dia. |
| 7 | Supplying and fixing one set wall mounting / standing type panel board of size 900mm x 300mm x 150mm of M.S. angle 30mm x 30mm x 6mm). The panel should have suitable arrangements for fixing Voltmeter, Voltmeter selector switch, Ammeter, Ammeter selector switch, 3 Nos of Indicator, 3 Nos of flush type switch, 3 Nos of flush type fuses, 3 Nos of incandescent bulbs, 3 Nos of C.T. Coil etc. including wiring with 4 sqmm and 1.50 sqmm copper wire - 63 Amps TPN main switch.-upto 12.5HP |
| 8 | Supplying and fixing of 4KVAR power capacitor for 10 HP motor complete. |
| 9 | Supplying and fixing of DOL starters 0.5 HP to 5 HP with relay range 0.63 A to 13 A with suitable M.S. angle frame complete. |
| 10 | Supplying and fixing of 1x3x4 sqmm (single run) PVC insulated copper submersible flat flexible cable complete.-upto 10HP pumpset. |
| 11 | Providing, laying and jointing UPVC pipes (1 Mpa)conforming to IS specification 4985 and ISI marked including transportation to the site , lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment, including cost of solvent cement, excluding UPVC specials such as bends, tees, threaded pieces, couplers, reducer, endcaps etc.,complete all as per IS and CPWD specification. - 90mm dia. |
| 12 | Providing and fixing in position UPVC moulded tail piece without flange (0.6 Mpa)conforming to IS 7834 part II and ISI marked,including labour charges for jointing, jointing materials etc,complete - 90mm dia |
| 13 | Providing and fixing in position UPVC fabricated coupler (1 Mpa) conforming to IS 7834 part II and ISI marked,including labour charges for jointing, jointing materials etc,complete - 90 mm dia |
| 14 | Providing and fixing in position UPVC fabricated bend (0.6 Mpa) conforming to IS 7834 part II and ISI marked,including labour charges for jointing, jointing materials etc,complete - 90 mm dia |
| 15 | Supplying of electrically operated wet type submersible motor and pumpset , AC 3 phase, 415 volts, 50 Hz, 2900-3000 RPM. The pump shall have brass impeller, high grade steel shaft with sufficient stages having outlet size of 2\\"/2.5\\"/3\\" dia. to suit the borewell (150 / 200mm dia.), complete.The rate includes, all taxes, freight, etc., FOR at site in UT ofPuducherry. The pumpset shall be guaranteed for a period of one year from the date of commissioning.(5 HP Submersible motor and pumpset). |
| 16 | Supplying,fixing and lowering into the borewell high tensile threaded PVC column pipes which are to be connected to the submersible pump,including labour charges,jointing materials etc.,complete.-75/80 mm dia |
| 17 | Supplying and laying of 16mm dia nylon rope for holding of motors. |
| 18 | Supply and fixing of 80/100mm dia. M.S. erection clamps of size 80mmx12mm with bolts, nuts, washer etc., complete. |
| 19 | Erection, testing and commissioning of submersible motor and pumpset complete.. Please Enable Macros to View BoQ information |
