Tender For Certain Misc Comprehensive B/R Repairs To Md And Otm Accn Of Eme School Under Ge (Army) Baroda.
Tender Value
20 Lakhs
Estimated cost
Bid Submission
08 Jul 2026
1 days left
EMD
40000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Vadodara → Gujarat
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Certain Misc Comprehensive B/R Repairs To Md And Otm Accn Of Eme School Under Ge (Army) Baroda.
BOQ
| Sl. No. | Item Description |
| 1 | Taking down chowkats or frame with shutter (without taking off shutter from the frame) n.exc 1.5sqm each & removing complete. |
| 2 | Taking down chowkats or frame with shutter (without taking off shutter from the frame) Exc 1.5 Sq m but n.exc 4.00 Sq m each & removing complete. |
| 3 | Taking down shutters of any description exc 1 sq. m n exc 2 sq.m each complete |
| 4 | Taking down shutters of any description exc 2 sq.m each complete |
| 5 | Refixing of Shutters of any description exc 1 sq. m but n exc 2 sq. m each in same position |
| 6 | S & F powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified. |
| 7 | S & F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. |
| 8 | M & L for 5.5mm thick sheet glass, exc 0.5 Sqm ordinary quality and glazing with rubber beading or with glazing clips, all as specified and directed. |
| 9 | S&F 12 mm thick Prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination fixed with screws to frame work complete. |
| 10 | M & L for 4 mm thick sheet glass, n. exc 0.5 Sqmfigured quality and glazing with rubber beading or with glazing clips, all as specified and directed. |
| 11 | S & F 4.00mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane |
| 12 | S&F in repairs aluminium (Extruded section) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete. Make: Dyna and equivalnt ISI marked. |
| 13 | S & F in repairs double action floor spring, hydraulically regulated, made up of minimum 1.25 mm thick aluminium alloy sheet, foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed all as specified and directed. |
| 14 | S&F for Framed work as in doors or gates or grill/grating of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specifed and directed. |
| 15 | M&L for 35mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels, comercial type 1.0mm thick (veneered on both side) with decorative choice laminated type on one side and white on another side (factory laminated), or surface finish, 6mm thick or external teak wood lipping fixed with nails, color and pattern as approved by EIC/GE. |
| 16 | S&F 2nd class Hard wood 35mm thick glazed & skeleton door shutters open rebated & prepared to receive glass, gauze etc, divided into squares with plain, chamfered or rounded, mitred and rebated sash bars, any numbers fitted with cut and miterd beds securing glass, sizes of members of shutters as specified in SSR part -I, section 8, clause 8.20(a) and fitted to chowkats. |
| 17 | M&L for two coats of synthetic enamel paint over a coat of pink primer of new wooden surfaces of any description, not otherwise descri-bed over 10cm width or girth complete. |
| 18 | S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanised staples complete all as specified and directed. |
| 19 | S&F in repair stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanised staples complete all as specified and directed. |
| 20 | M & L for Hacking out old broken glass Exc 1.5 sqm (any thickness, size, quality or description) from wooden/steel/aluminium frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads. |
| 21 | M & L for 100 mm butt hinges stainless steel grade 202, 14 gauge thickness medium weight fixed with pressed steel door frame / pvc door frame with screws. |
| 22 | S&F 300mm aluminum anodised sliding door bolts, with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast alluminium alloy complete all as specified and directed. |
| 23 | S & F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing. The door frame shall be tied to the wall using 75/100mm long MS screw as directed. |
| 24 | S & F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails. M S tube for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stile and rails with suitable PVC sheet beading and jointed together with solvent cement. |
| 25 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60(Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms)fabricated with miter joints after applying PVC solvent cement and screwed with fullbody threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant 152 SECTION 8 and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugsor SS dash fasteners shall be paid forseparately). ®Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified and directed. |
| 26 | S&F Factory made single extruded WPC (Wood PolymerComposite) solid plain flush door shutter of 30mm sizecomprising of virgin polymer of K value 58-60(Suspension Grade), calcium carbonate and natural Fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately complete all as specified and directed. |
| 27 | Providing and fixing factory made 18(+0.7mm) thick PVC sheet one sided pre laminated sheet cabinet shutter. 18 mm(+0.7mm) thk sheet shutter of density 600 kg/m3 bent at 90 degrees and finished all edges at all level for making edges, Lipping/bending or 0.5 mm thk PVC sheet lipping at all four edges using bonding tape etc complete all as per directions of engineer in Charge & Manufacturers's speciifcations. |
| 28 | S&F 100 mm long safety type aluminium anodised hasp and staple with hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed. |
| 29 | S&F 150 mm extruded aluminum alloy handles, fabricated type anodized complete all as specified and directed. |
| 30 | S & F 150 mm long aluminium anodised barrel tower bolt of extruded section and fixed, all as specified. |
| 31 | S & F 200 mm long aluminium anodised barrel tower bolt of extruded section and fixed, all as specified. |
| 32 | Demolition of Brickwork or stone/boulder masonry, built in lime mortar including all quoins, arches, pillars, ashlar facings, dressed stonework, precast concrete articles and precast concrete block walling etc. all as specified and directed. |
| 33 | M & L for Brickwork with sub class ‘B’ bricks straight or curved on plan exc 6 m mean radius built in CM 1:6 |
| 34 | Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete |
| 35 | M & L for 10 mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces and surface finished even and smooth without using extra cement all as directed. |
| 36 | M & L for rendering 5mm thick on brick wall surface or concrete surfaces of ceiling in cement mortar 1:3 for finished even and smooth (without using extra cement) |
| 37 | M&L Rendering in two layer on fair faces of brick work or concrete surfaces of wall 5 mm thick in CM 1:4 mixed with WPC @ 3% by wt of cement for finished even and smooth without using extra cement over 10 mm thick rendering in cement mortar 1:6 smooth without using extra cement (WPC will be measured separately). |
| 38 | Supply only Integral water proofing compound |
| 39 | M & L for preparing new plastered surfaces of ceiling and applying two coats of oil bound distemper over a coat of alkali resitant primer all as specified and as directed. |
| 40 | M & L for preparing new plastered surfaces of wall and applying two coats of oil bound distemper over a one coat of alkali resistant primer complete all as specified and as directed |
| 41 | M & L for preparing new plastered surfaces of wall and applying two coats of oil bound distemper over and including a coat of 2mm average thick birla/equivalent wall care putty and one coat of alkali resistant primer complete all as specified and as directed |
| 42 | M&L for preparing new plastered surfaces of wall and applying two coats cement base paint over a coat of primer complete all as specified and as directed |
| 43 | M & L for preparing old plastered surfaces of wall and applying two coats cement base paint on external wall complete all as specified and as directed. |
| 44 | M & L for preparing old plastered surfaces of wall and applying two coats of oil bound distemper over a coat of primer complete all as specified. |
| 45 | Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15 cm thickness (below or above ground level) |
| 46 | M&L for 50mm avg thick PCC padding in cement concrete (1:2:4) type B0 (Using 12.5mm graded stone aggregate) finished even and smooth without using extra cement for as in roof. |
| 47 | M&L for 75 mm thick PCC 1:4:8 mix ,type D-2 Using 40 mm graded stone aggregate finished even and fair without using extra cement as in sub base of path/hard standing |
| 48 | M&L for PCC 1:3:6 type C-1 , 75 mm thick as in plinth protection, Path, floor complete all as specified and directed. |
| 49 | M&L for Forming Contraction (Dummy) joints 75 mm deep x 10mm wide, filled with sealing compound complete all as specified and directed by EIC. |
| 50 | Demolition of stone slabs and tiles of any description or thickness in floors & wall, laid bedded & pointed in any mortar. |
| 51 | M&L for non skid colour ceramic tile 7 to 8mm thick area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or colour cement to match screed bed or bedding layer of mortar including 15mm thick for laying floor finishes with CM 1:6. |
| 52 | M&L for non skid colour ceramic tile 7 to 8mm thick area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, in skirting etc set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick rendering for backing coat on vertical surface of wall or concrete surfaces in CM 1:4 to receive wall tiles. |
| 53 | M&L for coloured (of any shade) vitrified ceramic tiles 9 to 10 mm thick (square/ rectangular) polished, area of each tile n.exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15mm thick for laying floor fiishes with CM 1:6 complete. |
| 54 | M&L for coloured (of any shade) vitrified ceramic tiles 9 to 10 mm thick (square/ rectangular) polished, area of each tile n.exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick rendering for backing coat on vertical surface of wall or concrete surfaces in CM 1:4 to receive wall tiles. |
| 55 | M&L for Glazed ceramic coloured walls tiles in vertical surfaces 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick rendering for backing coat on vertical surface of wall or concrete surfaces in CM 1:4 to receive wall tiles. |
| 56 | M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed base 15 mm thick screed bed in cement morter1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. |
| 57 | M&L for machine cut kota stone slab 20 - 25mm thick in skirting, riser etc set in vertical surface of wall or concrete surfaces over 10mm backing coat in CM 1:4 to receive wall tiles complete. |
| 58 | Material and labour for grinding and polishing of terrazzo floor with machine. |
| 59 | All as per item No.56 above but in skirting/dado (grinding/ polishing by hand). |
| 60 | Polishing of old existing Kota stone flooring i.e, grinding, joints pigment filling and polishing to get mirror finish all as specified and directed. |
| 61 | All as per item No.58 above but in skirting/dado (grinding/ polishing by hand) |
| 62 | M&L for Green Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble to match screed bed or bedding layer of mortar including 15mm thick for laying floor finishes with CM 1:6. |
| 63 | M & L chequered cement concrete tile 20cm x 20cm x 25mm thick with grey colour and pigment set and jointed in neat cement slurry including screed bed or bedding layer of mortar 15mm thick for laying floor finishes with CM 1:6 |
| 64 | M&L for Machine pressed, precast plain cement concrete Interlocking paver block, factoty made( with grey cement and no pigment) conforming to IS-15658-2006, 60mm thickness laid over and including 25 mm average thick sand cushioning layer & joints filled with sand in hardstanding etc, fabricated with M-35 grade concrete, complete. |
| 65 | Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings all as directed. |
| 66 | S & F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa, AZ150 as in roof covering/ cladding to wall, fixed with self tapping screws as specified. |
| 67 | S & F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa, AZ150 as in roof covering/cladding ridge or hips, valley gutter to wall, fixed with self tapping screws as specified. |
| 68 | M & L for preparing new steel surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer. |
| 69 | Dismantling ceiling and wall boards or insulation board any thickness including cover fillets complete. |
| 70 | Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers with G.I. wire mesh to hanging and size of grid 605x605 mm Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre (Fillets, metal frame work and G.I. wire mesh paid separately) complete |
| 71 | S&F non asbestos acoustic false ceiling 12mm thick with aluminum anodized snap grids of 60x60cm in ceiling with Tee section 35x25x1.25mm, angle section 25x25x1.25mm thick including 2mm dia GI hanging wire including all hanger including three coats of white wash in ceiling boards or match the shed of existing surface to a true surface complete. Make: Armstrong or equivalent |
| 72 | S & F 20 mm outer dia (internal 16mm dia) CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal out side MD land complete all as specified and directed |
| 73 | S & F 25 mm outer dia (internal 20mm dia) CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal out side MD land complete all as specified and directed |
| 74 | S & F 32 mm outer dia (internal 25mm dia) CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including taking up or down GI tubing 25mm bore from trenches/wall including all fittings segregated and stacking the pipecomplete all as specified and directed |
| 75 | M&L in repairs PVC (SWR) floor trap, plain with grating including jointing with solvent cement concrete type B1, 1:2:4 for 75mm bore. |
| 76 | S&F in repair 600mm x 450mm beveled edge mirror 5 mm thick of selected quality glass mounted on 6 mm thick commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers with aluminium beading. |
| 77 | S & F in repairs plastic seat white, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device |
| 78 | S & F in repairs Vitreous China wash down water closet pan pedestal pattern (Europian type) (excluding flushing cistern and flush pipe) plastic seat black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device. |
| 79 | S&F in repairs Vitreous China wash down water closet (Squat pattern ) white complete as fixed in repair excluding flushing cisternand flush type \\"Orrisa\\" pattern size 580x440 with integral footrest inject connection to trap antisyphonage etc complete including joint between flushing pipe and socket of WC. |
| 80 | S & F in repairs PVC valvless syphonic action flushing cistern low level white of 10ltrs capacity with inlet ball valve float and handle including bracket. |
| 81 | S&F in repairs health faucet mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 82 | S&F in repairs Vitreous china premium/ 1st quality wash down water closet wall hung EWC white/ ivory/off white (closed pattern incl all necessary accessories like rag bolts/ gel gasket etc. (excluding flushing cistern & flush pipe) of size 655 x 350 x 735 mm (Cat. No. S1031101) including plastic water closet seat, (Cat. No. B1520102) soft close seat cover, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging devicecomplete in all respect all as specified. (Make: Cera or equivalent) |
| 83 | S&F in repairs PVC connection 600mm long of dia 15mm complete. |
| 84 | S&F in repair Vitreous China wash hand basin, angle back 550 x 400mm white excluding taps, waste chains and plugs and porcilain stopper but including CI bracket and nut bolts as per maufacturers instructions. |
| 85 | S&F in repairs 32mm dia flexible waste pipe for urinal, wash basin and kitchen sink for length exc. 1m not exc 2m complete. |
| 86 | S&F in repair SS waste coupling of 32mm dia (half or full thread) including taking down old coupling of any description complete all as specified and directed. |
| 87 | Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided |
| 88 | M & L for reinforced cement concrete1:2:4, type B1, using 20 mm graded stone aggregate in Beams, cantilevers, bressummers, lintels over 1.5m span. |
| 89 | Use & waste Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc |
| 90 | M & L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete. |
| 91 | As per item no. 90 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete. |
| 92 | M & L for complete removal of loose / cracked concrete incl reinforcement if required, from RCC roof projection,chajja,fins,facia etc and making good with PCC (1:11/2; :3) type A0 (using 12.5 mm graded stone aggregate) in any slab and in any position finished the surface even and smooth with out using extra cement including necessary form work and welding/binding of reinforcement (including reinforcement) if required, including a coat of Epoxy bonding agent of Dr Fixit/FOSROC/PIDILITE to old concrete/Cement surface and applying three coat of white wash/two coat of cement base paint to match with the existing surface complete all as specified and directed by the Engr- in -Charge. (Reiforcement will be measured and paid saperately under respective item). |
| 93 | S&F in repairs 110mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints and fixed to wall as in waste/soil pipe complete all as specified and directed |
| 94 | S&F in repairs 75 mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints and fixed to wall as in waste/soil pipe complete all as specified and directed |
| 95 | S&F in repairs 110 mm dia PVC (SWR) bends of any radius with access door complete |
| 96 | S&F in repairs 75 mm dia PVC (SWR) bends of any radius with duck foot or heel rest fitted with oval access door complete. |
| 97 | S & F in repairs stainless steel socket fancy type with bracket for 25mm dia stainless steel tubular curtain rod (design of socket shall be approved by GE/AGE at the time of execution) as directed |
| 98 | S & F rotational moulded PVC water storage tank 1000 ltrs capacity conforming to IS-12701(1989) cylindrical vertical type Four-layered, white coloured with closed top including inlet,outlet and wash out holes of approved make hoisted and fixed in position all as specified in SSR Part I, including S&F Ball brass valves, for 25 mm bore of pipe high pressure, with polythene float and fly- nut complate, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed |
| 99 | S & F rotational moulded PVC water storage tank 500 ltrs capacity conforming to IS-12701(1989) cylindrical vertical type Four-layered, white coloured with closed top including inlet,outlet and wash out holes of approved make hoisted and fixed in position all as specified in SSR Part I, including S&F Ball brass valves, for 25 mm bore of pipe high pressure, with polythene float and fly- nut complate, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed |
| 100 | Disconnecting existing tanks exc 250 ltr but n exc 500 ltr, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. |
| 101 | Disconnecting existing tanks exc 500 ltr but n exc 1000 ltr, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. |
| 102 | S&F 20mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 142 gms) complete all as specified and directed. Make : Prayag & equivalent. |
| 103 | All as per item No 102 here in before but 25mm dia complete all as specified and directed. Make : Prayag & equivalent. |
| 104 | S&F in repairs 15mm dia stop valves cast copper alloy screwed down high pressure with crutch or butterfly handle for iron pipe |
| 105 | S&F in repairs, bib taps fancy type chromium plated 15mm bore cast copper alloy with capstan heads, screwed down high pressure with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed. |
| 106 | S&F in repair 15 mm bore Pillar taps, cast copper alloy, with capston heads, chromium plated fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed. |
| 107 | S&F in repairs sinks with draining board made of stainless steel 1 mm thick kitchen with plugs, washers and waste , including bedding in cement mortar on to dwarf wall or including fixing cantiliver brackets and connecting union to pipe, overall size 915mm x 460 mm & bowl size 410mmx330mm x 160mm complete. |
| 108 | S&F in repairs sinks made of stainless steel 1 mm thick kitchen with plugs , washers and waste , including bedding in cement mortar on to dwarf wall or including fixing cantiliver brackets and connecting union to pipe, overall size 495mm x 420 mm & bowl size 410mmx330mm x 160mm complete. |
| 109 | S&F in repairs chromium plated shower rose with or without swivel joints any size, including fixing to GI pipe for 125mm dia complete all as specified & directed. |
| 110 | S&F in repairs brass CP centre hole basin mixer for mixing hot & cold water three way screwed down for iron pipe 15mm bore and fixed complete. |
| 111 | S&F in repairs brass CP wall mixer for mixing hot & cold water three way screwed down for iron pipe 15mm bore and fixed complete. |
| 112 | S&F in repairs, towel rack 600mm Long with Lower Hangers, Stainless Steel complete all as specified and directed. (Make: Jaquar or equivalent) |
| 113 | M&L for cement concrete (1:5:10) type E-2 using 40 mm graded stone aggregates as in foundation, filling and mass concrete/sunken floors mixed with liquid water proofing compound @ 0.200 litre per bag of 50 kg of cement.NOTE:- Liquid water proofing compound shall be measured and paid for separately as “Supply only”.all as specified and directed. |
| 114 | M&L for 15 mm thick rendering on floor and vertical side of sunken floor of stone masonry surfaces/brick work/concrete surfaces in CM (1:3) mixed with liquid water proofing compound @ 0.200 litre per bag of 50 kg of cement and finished even and smooth without using extra cement complete all as specified and directed. NOTE:- Liquid water proofing compound shall be measured and paid for separately as “Supply only”. |
| 115 | Supply only liquid water proofing compound. |
| 116 | S&F in repairs floor door stopper of aluminium alloy body and tongue, overall length of cover plate 140mm anodised with hard drawn steel spring, fixed in floors complete all as specified and directed. |
| 117 | M&L Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in matching white cement (1:2) ,colour and pattern of granite shall be as approved by Engr-in-charge. |
| 118 | S&F in repairs Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) |
| 119 | S&F door sill of any size made up of rubber at the bottom and top is of aluminium sheet including screwing to protect from rats, snakes etc. complete all as specified and directed. |
| 120 | S&F in repairs, flush cock 25mm bore cast copper alloy with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed. |
| 121 | S&F in repairs, magnet door stopper of size round or rectangular including all fittings fixed complete all as specified and directed. |
| 122 | S&F in repairs, chromium plated peg set for hat and coat hooks including all fittings fixed complete all as specified and directed. |
| 123 | S&F in repairs Mild steel Mortice lock of 2 levers, vertical type, size 100 mm for Aluminium/Flushed doors complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Jun 25, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedJul 08, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 1 dayJul 09, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 2 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender