|
| 1 | Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth and getting out in hard/ dense soil for exposing of pipe etc complete all as specified and as directed by Engineer-in-Charge. |
| 2 | Returning, filling in including spreading, levelling, watering and well ramming soil in layers not exceeding 25 cm thick complete all as specified and as directed by the Engineer-in-Charge |
| 3 | Removing excavated material to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and as directed by Engineer-in-Charge |
| 4 | Taking up old unserviceable Ductile Iron water mains 150/100/80 mm dia including all fittings, with spigot and socket ends and lead joints including burning out joints and lead complete all as specified and as directed by Engineer-in-Charge |
| 5 | Supplying, laying and jointing centrifugally (Spun) ductile iron pipe (Class K-7) 100 mm bore with suitable for push on joints and centrifugally applied cement mortar leveling inside and Zinc coating with bituminous finish coat on outside of the pipe conforming to 1S-8329 of 2000, in any length, laid in trenches in proper alignment including necessary cut to length to match existing fitting/pipes or insertion of new CI specials etc complete all as specified and as directed by Engineer-in-ChargeNote: Rubber gasket joints (tyton), specials such as bends/ tappers/ tee/ cross of any type and size and earth work excavation will be measured and paid separately. Make: Tisco / Electro Steel / Kesoram / Lanco / Jindal / Kalinga / Kapilansh. |
| 6 | Material and labour for cutting of DI/CI pipe upto 150mmm bore and reducing to required length in position complete with insertion of new Tee, tail pieces, reducers valves etc and including necessary earth work complete all as specified and as directed by Engineer-in-Charge.Note: Specials such as Tee, tail pieces, reducers valves etc will be measured and paid separately. |
| 7 | Supply, fix and jointing steel water tubing of 80mm bore medium grade, galvanised iron with all fittings such as Tees, elbows, sockets, bends, unions, short pieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239 including fixed to wall / ceiling or laid in floor with suitable size GI clamps including taking down existing GI pipe and making good disturbed surfaces as per existing surfaces complete all as specified and as directed by Engineer-in-Charge.Make: Tata / Jindal / Surya Prakash / Zenith |
| 8 | ditto as per item no 07 above but for 50 mm GI bore pipe. |
| 9 | ditto as per item no 07 above but for 40 mm GI bore pipe. |
| 10 | ditto as per item no 07 above but for 25 mm GI bore pipe. |
| 11 | ditto as per item no 07 above but for 20 mm GI bore pipe. |
| 12 | Supply and fix gun metal gate valve of 50mm bore with iron wheel head, screwed both ends for iron pipes & fixed including taking down existing etc complete all as specified and as directed by Engineer-in-Charge for following sizes:Make: Kirloskar / Zoloto / Kartar / Upadhaya / Leader / BIR |
| 13 | ditto as per item no 12 above but for 40 mm GI bore. |
| 14 | ditto as per item no 12 above but for 25 mm GI bore. |
| 15 | Supply, fix, joint and testing Cast Iron Sluice Valve heavy duty of 150mm dia, with stainless steel spindle, PN 1.6 (Flanged) with iron wheel head, hand operated, bronze body seat ring, jointing, coupling both ends for cast iron pipes including nuts, bolts, rubber gaskets etc including taking down old unserviceable Sluice valve complete all as specified and as directed by Engineer-in-charge.Make: Kirloskar / Kartar / Upadhaya / Leader / Venus / L & T (audco) |
| 16 | ditto as per item no 15 above but for 100 mm dia. |
| 17 | ditto as per item no 15 above but for 80 mm dia. |
| 18 | Material and labour for construction of new valve chamber of size 1200mm x 1200mm x 600mm ( Internal size) including necessary excavation and earth work in any type of soil, PCC foundation (1:3:6) type C-2, using 40mm graded stone aggregate as in base concrete 100mm thick, 15cm offset, 230mm thick brick work in CM 1:6 with 10 mm thick rendering internally and 15 mm thick externally in CM 1:4, 50mm thick PCC 1:2:4 type B1 as in coping, 6 mm thick MS cover with hinges and locking arrangement, fixed to angle iron frame made out of 40 x 40 x 6 mm MS angles complete with two coats of synthetic enamel paint over one coat of red zinc chrome primer on all metal surfaces & three coats of white wash on all plastered surfaces of valve chambers including dismantling of unserviceable valve chamber with rusted MS cover without disturbing the existing pipeline etc complete all as specified & directed by Engineer -in-Charge. |
| 19 | ditto as per item no 22 above but of size 900mm x 900mm x 600mm ( Internal size) |
| 20 | Material and labour for desludging / desilting of RCC over head water tank of 50000 Gallons capacity by draining out water / sludge from tank, removing all scales, dirt, algae and other growths from floor, roof, inside of tanks and from mouths of circulating pipes by rubbing with wire brushes and high pressure cleaning method with rotary sets with approved detergents and sucking out all dirty water by vacuum cleaners, disinfecting the tank with approved chemical solution for making surface bacteria free and finally cleaning with fresh water to the satisfaction of Engineer - in- Charge including painting MS plates manhole covers, suction pipes, rugs, etc. with two coats of anticorrosive paint and writing outside the tank as TANK CLEANED on_______and capacity _______ on black painted surface including removing all dirt outside land to a distance exceeding 50 mts complete all as specified and as directed by Engineer-in-Charge. |
| 21 | All as per item No. 20 described here-in-before but 25000 Gallons capacity |
| 22 | Material and labour for desludging / desilting of underground sedimentation reservoir of 80000 Gallons capacity by draining out water / sludge from tank, removing all scales, dirt, algae and other growths from floor, roof, inside of tanks and from mouths of circulating pipes by rubbing with wire brushes and high pressure cleaning method with rotary sets with approved detergents and sucking out all dirty water by vacuum cleaners, disinfecting the tank with approved chemical solution for making surface bacteria free and finally cleaning with fresh water to the satisfaction of Engineer - in- Charge including painting MS plates manhole covers, suction pipes, rugs, etc. with two coats of anticorrosive paint and writing outside the tank as TANK CLEANED on_______and capacity _______ on black painted surface including removing all dirt outside land to a distance exceeding 50 mts complete all as specified and as directed by Engineer-in-Charge. |
| 23 | All as per item No. 22 described here-in-before but 50000 Gallons capacity |
| 24 | All as per item No. 22 described here-in-before but 25000 Gallons capacity |
| 25 | All as per item No. 22 described here-in-before but 20000 Gallons capacity |
| 26 | All as per item No. 22 described here-in-before but 15000 Gallons capacity |
| 27 | All as per item No. 22 described here-in-before but 10000 Gallons capacity |
| 28 | Material and labour for Carrying out scheduled maintanence and servicing of all electro - mechanical machinery of existing centrifugal, submersible, monoblock pump,motor and accessories any type any make & model in every days or when ordered including cleaning it's part, removing corrosion, refixing it, rectifying leakage due to loose nut / stud/ gland packing/gland rope/ star packing/ clamps/washers etc of suitable size as required complete all as specified and as directed by Engr-in-charge.Note- Unit each is for per each job of servicing |
| 29 | Material and labour for dismantling Monoblock/ Centrifugal electric motor of 415 volts, 40 HP capacity including removing of electric connection from its position carefully and transporting the same to the work shop for rewinding of motor (both stator and rotor) with super enamelled copper wire of same size with existing motor of pump set with insulating materials, varnishing and baking, replacement of worn-out bearings etc as required including re-fixing, connecting with existing electric cable etc., testing & commissioning for satisfactory functioning etc complete all as specified and as directed by Engineer-in-Charge. |
| 30 | All as per item No. 29 described here-in-before but for 15 HP pump set |
| 31 | All as per item No. 29 described here-in-before but for 10/12.5 HP pump set |
| 32 | All as per item No. 29 described here-in-before but for 5/7.5 HP pump set |
| 33 | Material and labour for dismantling and disconnecting upto 15 HP 3 phase open well submersible sewage pump from pump house, transporting to contractor's workshop, dismantling and carrying out necessary repairs/replacement of motor as following :(a) Cutting out existing winding of stator of monoblock motor of any make and rewinding with same size of copper winding wire as existing guage.the electric motor and re-assembling the pump set on existing foundation after repair / overhauling of motor including following and testing complete all as specified and as directed by Engineer-in-Charge. (b) Straightening the slot of starter of submersible motor of any make(c) Replacement of thrust washer and bearing complete(d) Replacement of worn out bushes of submersible motor (e) Replacement of sand guard(f) Providing of sleeves in end plate of submersible Pump(g) Replacement of grommet (h) Replacement of water seal(j) Lathe work of motor shaft to bring it to original size and shape and plastering of shaft of submersible motor for smooth functioning on desired amps. |
| 34 | Material and labour for Painting of motor pump base, discharge line within the pump house arealine and suction line complete with all accessories including panel board with scrapping thoroughly existing corroded paint and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed by Engineer-in-Charge. Make : Asian paints/ Nerolac paints / Berger paints / Shalimar paints / Dulux/Birla Opus Paint |
| 35 | Supply and fix monoblock centrifugal pump set 3 Phase, 415volts, 2 HP, 1.5 KW capacity with 50mm suction and 40mm dia delivery having discharge capacity 5 ltr/sec at 26mtr head complete with cast iron /MS base plate etc including taking down existing complete all as specified and as directed by Engineer-in-charge.Make: Kirloskar model KDI-225+ or equivalent to KSB /Jyoti / Beacol |
| 36 | Supply and fix 10000 litre premium high-grade PVC cylindrical vertical water storage tank (maximum diameter 2.5m, maximum height 3.2m) with all accessories plumbing fittings, sealing materials, and control valves and fix at the rquired height conforming to IS 12701 safety specifications, complete in all respects as specified and directed by the Engineer-in-Charge. Make- Sintex. Note: GI Pipe/control valve will be paid separately in respective item. |
| 37 | Supply and fix swing type Foot Valve 150mm dia conforming to IS 4038 and PN.02. the valve should be swing type rigid sturdy design with minimum loss of head across the valve , including necessary fixing arrangements including taking down complete all as specified and as directed by Engineer-in-Charge. Make: Kirloskar/Kartar/Normex |
| 38 | Supply and fix swing type Foot Valve 100mm dia conforming to IS 4038 and PN.02. the valve should be swing type rigid sturdy design with minimum loss of head across the valve , including necessary fixing arrangements including taking down complete all as specified and as directed by Engineer-in-Charge. Make: Kirloskar/Kartar/Normex |
| 39 | Supply and fix swing type Foot Valve 80mm dia conforming to IS 4038 and PN.02. the valve should be swing type rigid sturdy design with minimum loss of head across the valve , including necessary fixing arrangements including taking down complete all as specified and as directed by Engineer-in-Charge. Make: Kirloskar/Kartar/Normex |
| 40 | Supply and fix swing type Foot Valve 65 mm dia conforming to IS 4038 and PN.02. the valve should be swing type rigid sturdy design with minimum loss of head across the valve , including necessary fixing arrangements including taking down complete all as specified and as directed by Engineer-in-Charge. Make: Kirloskar/Kartar/Normex |
| 41 | Supply and fix swing type Foot Valve 50mm dia conforming to IS 4038 and PN.02. the valve should be swing type rigid sturdy design with minimum loss of head across the valve , including necessary fixing arrangements including taking down complete all as specified and as directed by Engineer-in-Charge. Make: Kirloskar/Kartar/Normex |
| 42 | Material and labour for cutting or cutting the existing Bitumen Road /hard standing to size not exceeding 30cm wide and depth not less than 45cm for passing of GI pipe and making good the disturbed surface filled with excavated material and top 200mm depth with plain cement concrete 1:3:6 type C1 using 20mm graded aggregate complete all as specified and directed. |
| 43 | Material and labour for repairing of pipe line by welding of GI/CI fitting of size 20-65mm dia at various locations to prevent leakage of water by welding of flanged / sockets / collars, ferrule or at the joints of including GP Joint, T joint, sluice valves / air release valve / non return valves or damaged pipeline etc., including necessary excavation and returning and filling and making disturbed surface good complete all as specified and as directed by Engineer-in-Charge |
| 44 | Material and labour for repairing of pipe line by welding of GI/CI fitting of size 80-150mm dia at various locations to prevent leakage of water by welding of flanged / sockets / collars, ferrule or at the joints of including GP Joint, T joint, sluice valves / air release valve / non return valves or damaged pipeline etc., including necessary excavation and returning and filling and making disturbed surface good complete all as specified and as directed by Engineer-in-Charge |
| 45 | Material and labour for repairing existing water level indicator of Overhead tank / Underground sump, painting, marking levels, replacing the nylon rope, float valve with new nylon rope and float valve refixing the same complete as per site requirement and and as directed by Engr -in-Charge. |
| 46 | Supply & Fix in repair pressure gauge dial type for measurement of the water pressure up to 15 Kg/cm 2 or as per existing size complete all as specified and directed.Make- Waarrie/H-Guru |
| 47 | Material and labour in repair Earthing complete with Galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of earth the plate not less than 1.5 metres below normal ground level, connected to plate with GI earth strip 32 x 6mm, 7.5 m long from earth point to test point and other end connected to control board / panel / equipment, laid under floors/plinths or fixed on walls or concealed in wall etc by means of bolts, nuts, check nuts and washers made out of galvanised iron or steel with provision of charcoal & common salt packed upto minimum 150 mm all around the earth plate and protected by 32 mm bore light grade galvanised iron pipe complete all as shown in electrical plate No.3 of MES schedule Part I, 2009 with PCC pit in PCC 1:2:4 type B1 using 20 mm graded stone aggregate, MS angle iron frame of size 50mm x 50mm x 5mm, cast iron cover with locking arrangements, GI 20 mm bore medium grade pipe and CI funnel with wire mesh for watering arrangement including necessary excavation and earth work in any type of soil/strata & testing complete all as specified and as directed by Engineer-in-Charge. |
| 48 | Material & Labour for testing of water quality by taking out water sample from pump houses and taking to govt. approved water testing laboratory and showing results of physical and chemical characteristics and micro biological test of water as per IS-10500 of 2012 and till latest version atleast 2 times from each pump house on an interval of 3 months complete all as specified and directed by engr-in-charge. Note : Price must include the transparent glass bottle in which water to be filled of minimum 1 ltr |
| 49 | Material and labour for Cutting under ground bushes grass small plant all as and where directed by EIC and removing the same from site and depositing at a distance n. exc 50 mtr complete all as directed. Note- Unit each is for per installation |
| 50 | Material and labour for Cleaning of valve pit chamber of any size by taking out mud & muddy water and depositing the same at a distance n. exc 20 mtr away from pit including swipping free from & all type of dirt including rectification the leakage of valve of any size by using of appropriate size and required packing materials for purpose and directed at site. |
| 51 | Supply, install, testing & commissioning Pedastal cubical type double door LT feeder piller box factory made modular construction fabricated out of 3 mm thick CRCA sheet, epoxy powder coated to give a superior finish ,outdoor type , totally enclosed dust & vermin proof with locking arrangements (compartment wise) front side opening system Overall size of each incoming & outgoing modules of (350x350x400)mm size and busbar chamber should be suitable for accomodating all Aluminium bus bar strips (40mm x 10mm x 04 Nos) duly covered by PVC sleeves fixed on porcelain insulators, and one independent metering module suitable for accomodating indicator lamps, cable entry/exits cut outs at bottom or upper part as mentioned below, complete electrically inter connected suitable size for all incoming and outgoing MCBs and accessories with fixing arrangement on wall with bolts, nuts & washers, Danger notice board with scull suitable for 415 volts or required size to be fixed on Panel and consisting of the following accessories including dismantling of old panel all as directed.Note:- (a) Panel shall be Manufactured from CPRI approved manufacturer and Drawing for Feeder pillar box shall be first approval by Engr-in-Charge(b) The cost of dismantling of old panel/F/piller Box is deem to be included above.(c) Panel indicating lamp neon/LED type (Red ,Yellow & Blue) with lamp holders - 03 Nos(d) Panel instrumental wiring with FRLS suitable size but not less than 6.0 sqmm copper wire single core - 01 Job |
| 52 | Incoming :-(a) MCCB 4 pole ,Ics=100%Icu- 25 KA, 415 Volts, 100 Amps , with thermal adjustable and fixed magnetic setting with extended terminals - 01 Nos. Outgoing :-(a) MCB TPN, 415 Volts,10 KA, 32 Amps -02 Nos. b) Star delta starter 15 HP 3 Phase for open execuision in panel with push button switch ON/OFF indicator on door of each module with protection relay- 2 Nos Make-Havells/ Siemens/ Larsen &Tubro/ ABB/ Crompton Greaves/ GE c) MDXL capacitor heavy duty 15 KVAR 3 phase 440 Volts Box type (Make : L&T Cat Part- LTBCH) with capacitor duty contactor ( Make : L&T Cat Part- MO C15) and 32 Amps TP MCB- 02 Set e) Digital Type Ampere meter 3 phase CT opearted with suitable size CTs-3 Nos for each meter complete all as directed- 04 Nos (make: L&T, cat Part-WL131010OOOO) f) Multifunctional meter (VAF + PF meter) for main incomming- 01 Nos. (Make- L&T Cat Part- WL41010OOOO)Make of MCCB & MCB: Larsen &Toubro/ ABB/ Siemens/ Schneider/ Havells/ Legrand/ Indo ASIAN/ C & S Electric/ Bhartia Cuttler Hammer (BCH) |
| 53 | Supply & Fix Chlorine dozing pump system to inject solution upto 25 LPH comprising dozing pump coupled with three phase electric motor of capacity 0.5 HP 1440 RPM assembly with agitator in one motor with SS sweep blade duly FRP coated FRP tank 150 ltrs capacity complete unit mounted on heavu duty MS fabricated frame duly anticorrosive paint complete all as specified and as directed by Engr-in-charge. |
| 54 | Material and labour for rolled mild steel sections as in roof trusses (framed), trussed, purlins, crane gantries, rails, and fastenings and heavy bracket framing, (beam, tee, angle, channels or flat sections) including notching, drilling, fitting, riveting and / or welding or connecting with bolts and nuts (including rivets or bolts and nuts) conforming to Fe 410 W Gde E- 250, Quality B complete all as specified and as directed by Engineer-in-Charge. |
| 55 | Supply and fix Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick as per approved profile of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or L type or J type or cranked hook bolts or as per manufacture instruction complete all as specified and as directed by Engineer-in-Charge.Make: JINDAL / INDALCO / HINDALCO / ASSOCIATED Profiles and Aluminium Ltd / ESSAR colour coated sheets/Tata |
| 56 | Supply & Fix Gallon seal for Pump Motor, Sluice valves of any size complete all as specified and as directed by Engr-in-charge. |
| 57 | Material and labour for replacement of valve chamber cover/ UG Sump cover/ladder made of iron including all material ,fabrication,fixing,supporting frame,anti corrosive surface and applying synthetic enamel paint two coat of red oxide primer complete with all as specified and as directed. |
| 58 | Material and labour for Dismantling and taking down centrifugal pump set 15 to 40 HP capacity, 3 phase, 440 volts from foundation, disconnecting all electrical connection from induction motor, transportation from installation to workshop, renewal of u/s spare parts, re-assembling pumping set including testing and commisioning including proper allignment of pump with motor complete all as specified and as directed by Engr-in-charge. |
| 59 | Supply only following spare parts( Item No a to j) suitable for existing 15 to 40 HP centrifugal pump set as required:- |
| 60 | Ball bearing suitable for centrifugal pump set 15 to 25 HP. |
| 61 | Ball bearing suitable for centrifugal pump set 30 to 40 HP. |
| 62 | CI impeller suitable for centrifugal pump set 15 to 40 HP. |
| 63 | Fan blade set |
| 64 | Low jaw coupling including necessary key for fixing on shafts as required. |
| 65 | Rubber star packing of size 011/013/015 for jaw coupling fitting . |
| 66 | Supply only SKF wheel bearing Grease of 1 kg box (base oil viscosity 110mm2/s@40 degree c ) operating temprature - (-30 to +120 degree c ) |
| 67 | Supply only lead wool (caulking lead) confirming to IS- 782-1978. |
| 68 | Supply only Chloroscope (Chlorine Testing Kit) 1 PPM to 5 PPM for testing of chlorine in water including orthodine solution complete all as specified. |
| 69 | Material and labour for removing existing old unserviceable water meter and supply, fix and testing new water meter of size 80mm (3\\") industrial type, super dry dial, helix turbine type removable mechanism and works on magnetic drive, class 'B' with flanged ends including CI collar with flange, suitable hexagonal bolts, nuts with rubber gasket and fasteners etc complete all as specified and as directed by Engineer-in-Charge. Note: The rates includes testing meter to concern BMC Office and test report shall be submitted by the contractor to Dept. before installing new meter. Make: Kranti / Captan / Anand - Zenner / Kaycee / Fedrel |
| 70 | Material and labour for Plain Cement Concrete 1:4:8 type D2 using 40mm graded stone aggregate as in foundation / mass concrete/filling complete all as specified and as directed by the Engineer-in-charge |
| 71 | Supply & Fix Sign glossy boards of size 150cm x 120cm and made out of 3mm thick glossy sheet with 40mm medium grade pipe frame & 3 mtr height above gound level including grouted in PCC (1:2:4) type B1 (using 20 mm graded stone aggregate), the board should duly written MES Pump House No ---------Name------- ,GE(N Santacruz complete all as specified and as directed by Engr-in-charge. Note: The content and size of chart/ poster /diagram / name plate etc shall be as per standard engineering practice given by the Engr in charge during execution of work. |
| 72 | Supply, fixing, testing and commissioning of Automation Panel for Motor starter panel for controlling of two centrifugal pump sets including Programmable Logic control (PLC), 240 volt AC Relay,Modular Card, SMPS, LED indicator lamps with push buttons including internal wiring with 32 Amp 4 pole MCB and 10 Amp SPN MCB with all connections, fabrication, Spray painting with smoke grey colour complete all as specified and as directed by Engr-in-charge. Make:- MITSUBISHI or equivalent Siemens or existing make/brand spare parts or any reputed suitable make and as approved by Engineer-in- Charge Note:- Any changes to control/communication circuits to be done in presence of OEM of panel manufacturer and Engineer-in- Charge |
| 73 | Supply & fix in repair Coil with Solenoid Valve - 15mm 230 V a.c complete all as specified and directed by Engineer-in- Charge Make: Avcon/Jhonson Control |
| 74 | Supply & fix in repair Coil with Solenoid Valve - 10mm 230 V a.c complete all as specified and directed by Engineer-in- Charge Make: Avcon/Jhonson Control |
| 75 | Supply & fix in repair Magnetic Level Sensor complete all as specified and directed by Engineer-in- Charge Make: SMI/CRYSTAL/SPLASH |
| 76 | Supply & fix in repair SS FLAP Butterfly valve of size 80 mm dia with actuator and single phase electric motor complete all as specified and as directed by Engr-in-charge. Make: AUDCO/ VIRGO/ INTERVALVE/L&T |
| 77 | Supply & fix in repair SS FLAP Butterfly valve of size 100 mm dia with actuator and single phase electric motor complete all as specified and as directed by Engr-in-charge. Make: AUDCO/ VIRGO/ INTERVALVE/L&T |
| 78 | Supply & fix in repair SS FLAP Butterfly valve of size 150 mm dia with actuator and single phase electric motor complete all as specified and as directed by Engr-in-charge. Make: AUDCO/ VIRGO/ INTERVALVE/L&T |
| 79 | Supply & fix in repair Limit Switch for Actuator suitable for 80 / 100 / 150 mm dia Butterfly Valve complete all as specified and directed |
| 80 | Supply & fix in repair Pressure Switch 0 - 10 kg/sq.cm complete all as specified and as directed by Engr-in-charge. Make: Indfos/ Danfoss |
| 81 | Supply & Fix in repair/replacement of 3 core 1.0 Sqmm armoured copper cable complete all as specified and as directed by Engr in chargeMake- Polycab/Havells/Prime Cab/ Finolex |
| 82 | Supply & Fix in repair/replacement of 4 core 6.0 Sqmm armoured copper cable complete all as specified and as directed by Engr in chargeMake- Polycab/Havells/Prime Cab/ Finolex |
| 83 | Supply & Fix in repair/replacement of 5 core 0.5 Sqmm armoured copper cable complete all as specified and as directed by Engr in chargeMake- Polycab/Havells/Prime Cab/ Finolex |
| 84 | Material and labour for dismantling existing GI pipe laid on surface upto 50mm size including fittings and relaying into underground trench including all type of GI fittings ( bends, elbows, union, nipple, Tees) complete all as specified and as directed by Engr in charge.Note- Excavation, Returning and filling, removing, gate valve, sluice valve will be measured and paid seperately under respective items of Schedule.) |
| 85 | Material and labour for dismantling existing GI pipe laid on surface upto 80/100mm size including fittings and relaying into underground trench including all type of GI fittings ( bends, elbows, union, nipple, Tees) complete all as specified and as directed by Engr in charge.Note- Excavation, Returning and filling, removing, gate valve, sluice valve will be measured and paid seperately under respective items of Schedule.) |
| 86 | Note: Deduct Credit for demolished / dismantled material of Rs. (-) 49,375.00 (Minus) as listed in Schedule of Credit. Tenderers will not quote against this item being a tentative amount to be considered to arrive at the 'Contract Sum' Please Enable Macros to View BoQ information |
