|
| 1 | Demolition of concrete of any description and in any position above or below ground level and debris off the premises (outside MD land) etc complete all as specified and as directed. |
| 2 | Material and labour for Plain Cement Concrete (1:4:8) type D2 using 40mm graded stone aggregate as in sub base, filling and mass concrete etc complete all as specified and as directed by Engineer-in-Charge. |
| 3 | Material and labour for Plain Cement Concrete type B-1 (1:2:4), using 20 mm graded stone aggregate as in top layers for hard standing, pavings etc finished with even and fair without using extra cement etc complete all as specified and as directed. |
| 4 | Material and labour for chequered cement concrete tiles (with grey cement and pigment) manufactured in rubber moulded finish of size not less than 300 x 300 x 22-25mm thick, set, jointed and pointed in neat cement slurry over and including 20mm thick cement mortar screed bed in CM (1:6) as in floors complete all as specified and as directed. |
| 5 | Material and labour for heavy duty vitrified parking tiles area of size not exc 0.36 sqm and 8-10mm thick set jointed with grey or coloured cement and pigment and pointed in neat cement slurry over and including 20 mm thick screed bed in CM(1:6) etc complete all as specified and as directed. |
| 6 | Material and labour for 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design and pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness and size / shape, made by table vibratory method using PU mould, laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed. |
| 7 | Material and labour for 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design and pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness and size / shape, made by table vibratory method using PU mould, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed. |
| 8 | Material and labour for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and as directed. |
| 9 | Material and labour for preparation of new concrete or cemented surfaces and applying two coats of plastic emulsion paint of approved tint over a coat cement primer etc complete all as specified and as directed. |
| 10 | Dismantling stone slabs and tiles of any description or thickness in floors, aprons, riser of steps, skirting, dado etc laid in any mortar complete all as specified and as directed. |
| 11 | Material and labour for 18 to 20mm thick granite stone (of any type) work (table rubbed and polished) as in floors, staircase tread and risers of steps, cooking platform, window cill / jambs or in vertical surfaces etc laid over and including 15mm thick CM (1:4) and pointed in white / coloured cement to match coloured tiles including rounding, grinding and mirror polishing complete all as specified and as directed. NOTE :- Colour of granite shall be as approved by Engineer-in-Charge. |
| 12 | Material and labour in repairs to stainless steel (Grade 304) railing made of hollow tubes, channels, plates, chains etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement and including taking down existing railing of any descriptions etc complete all as specified and as directed. |
| 13 | Demolition of brick work or stone masonry built in cement mortar including quoins, arches, pillars etc and precast concrete articles and deposing off the debris outside MD land complete all as specified and as directed. |
| 14 | Material and labour for precast cement concrete solid block masonry with solid blocks using Plain Cement Concrete 1:3:6, type C1 (using 20mm graded stone aggregate), exc.10cm in width, set in CM (1:6) complete all as specified and as directed. |
| 15 | Material and labour for walling of squared rubble, uncoursed, well bonded, bedded and solidly hearted, built in built in cement mortar (1:4) complete all as specified and as directed. |
| 16 | Taking down cement plaster on brick /stone masonry / concrete surfaces of wall / ceiling incl raking out joints, hacking for key, scrubbing down with water etc and deposited the debris outside the MD land complete all as specified and as directed. |
| 17 | Material and labour for rendering 15mm thick in cement plaster (1:4) on fair faces of brick work or concrete surfaces finishes the surfaces even and smooth without extra cement etc complete all as specified and as directed. |
| 18 | Material and labour for preparation on newly plastered wall surface and applying two coats of cement base paint of approved tint complete all as specified and as directed. |
| 19 | Material and labour for flush pointing to squared rubble masonry coursed or uncoursed in cement mortar (1:3) complete all as specified and as directed. |
| 20 | Demolition of reinforced cement concrete in any position of any description not otherwise specifically provided for, reinforcement cut through to facilitate demolition and deposing off the debris outside MD land complete all as specified and as directed. |
| 21 | Material and labour for precast Reinforced Cement Concrete, (1:2:4), type B1 using 20mm graded stone aggregate as in manholes / drain cover slab etc, set in cement mortar (1:4) including necessary form work etc complete all as specified and as directed. |
| 22 | Material and labour for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings, culverts and similar work; flat and rough finished surfaces not exceeding 200mm thick (Horizontal or sloping) etc complete all as specified and as directed. |
| 23 | Material and labour for reinforced cement concrete Type B1 1:2:4 using 20mm graded stone aggregates as in slabs supported on walls, beams, culverts and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like etc complete all as specified and as directed. |
| 24 | Material and labour for 300mm bore reinforced concrete pipes, class NP3, laid in trenches or in any locations and jointed complete with collars etc complete all as specified and as directed. |
| 25 | Material and labour for TMT mild steel bars 10mm dia and over, cut to length, bent to shape required including cranking bending mild steel wire annealed not less than 0.9mm dia or securing with clips complete all as specified and as directed. |
| 26 | Material and labour for providing Plain Cement Concrete, type B1, (1:2:4) using 20 mm graded stone aggregate as in kerbs of mud stops, borders, copings etc,. rounded or chamfered on edges, complete all as specified and as directed. |
| 27 | Material and labour for Plain Cement Concrete type B2 (1:2:4), using 40mm graded stone aggregate as in surface channels and drains etc complete all as specified and as directed. |
| 28 | Extra for forming fair finished drain or channel 30 to 45 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred / stopped ends etc complete all as specified and as directed. |
| 29 | Dismantling wrought iron or mild steel work of any description and in any position etc complete all as specified and as directed. |
| 30 | Supply and fix rolled mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290 Gde E-165 etc complete all as specified and as directed. |
| 31 | Material and labour for preparation of new steel surfaces over 10cm in width or girth not otherwise described and applying two coats of synthetic enamel paint of approved tint over one coat of red oxide zinc chrome primer complete all as specified and as directed. |
| 32 | Material and labour for preparation of old concrete or cemented surfaces and applying one coats of plastic emulsion paint of approved tint complete all as specified and as directed. |
| 33 | Material and labour for preparation and cleaning of floor or concrete surfaces and applying one coat of terracotta paint of approved tint complete all as specified and as directed. Please Enable Macros to View BoQ information |
