|
| 1 | Taking down copper/aluminium point wiring of any description and any position (light, fan, socket or power point) complete, including fixture and fittings such as switches,socket, ceiling rose,lamp holder,pendants, bracket and regulator etc removing material from site and making good disturbed surface to match with the existing surface complete all as specified. |
| 2 | M&L for point wiring with 1100 volt grade PVC insulated and unsheathed 1.5 Sq mm (FRLS) multistranded copper conductor cable with continuous earth wire of 1.5 Sq mm (FRLS) multistranded copper conductor cable PVC insulated and unsheathed, drawn in & including concealed/surface with PVC rigid conduit medium grade with fittings (ISI marked) not less than 20 mm dia & 1.6 mm thick sunken pressed steel galvanised terminal boxes with top cover ISI marked 3 mm thick plastic laminated hylam sheet for housing/ fixing switches etc complete all as specified and directed for the following-Note- (i) The quoted rete is deemed to be included for the chases cutting. (ii) Cutting chases for concealed shall be made good using CM 1:4 and surface finished to match the existing surface & colour. |
| 3 | One light/ holder/fan/exhaust/bell point controlled by one switch. |
| 4 | S&F in replacement of Switch Piano flush type 5 Amp single pole one way. |
| 5 | S&F in replacement of ceiling rose three terminal type made of high grade PVC/Poly carbonate isolated body, AC 230 Volts supply complete with necessary fixing accessories, complete all as specified and directed. |
| 6 | S & F in replacement Building security LED Light 25 Watt made up pressure die-cast aluminium housing with high power LED as lighting source and lens embedded PC having top opening separate driver compartment with IP-66 protection and impact resistance of IK 07 for building secuity purpose with bracket size made of GI pipe medium grade 32 mm dia 1.5 mtr long bend to shape as required and fixing with two nos MS Clamp of size 40x6 mm for fixing of builiding security light fittings completed all as specified and directed. |
| 7 | S&F in replacement LED street light 70 W made up of pressure die cast aluminium housing with polycarbonate cover and high power LEDs and secondary lenses with IP 66 protection 10 KV SPD included efficacy 110 LM/ 5700 K complete all as specified and directed. |
| 8 | S&F in replacment Post Top for 360 Degree 40W indirect light IP-65 protection resistant to impact and corrosion Glare. free and better uniformity incl provision of 50mm dia light grade GI pipe upto 0.6 mtr and incl painting of GI pipe, all connection complete all as specified and directed. |
| 9 | S&F in replacment LED bollard garden light IP 65, acts as an imposing street furniture. Resistant to impact and corrosion. Glare free and better uniformity incl necessary PCC foundation of size 200mmx200mmx200mm using (1:3:6) type C-1 (using 20mm graded stone aggregate) and fixing of PVC junction box and connection complete all as specified and directed. Note : Junction box will be measured and paid separately. |
| 10 | S & F in replacement pole mounted automatic street light controller panel with smart timer nature switch enclouser made of IP66 (Dust & Powerful jet water proof) as per IEC 60529, Self-Extinguishing & Flame Retardant, Silicone Free, Halogen Free, Corrosiveness of Fumes as per IEC 60754-2. Environment Friendly & Recyclable, Locking Arrangement: Transparent Lid is fitted with half-turn spring return fasteners for easy operation, material: Thermoplastic Polycarbonate, Durable for decades. Special moulding compound having facility duriation base 3-Phase load of 8kW with 3 nos. Incoming-Outgoing, MCBs of 16-20 Amps & 3 nos. Contactors (SP/2-pole/3-pole) of 20Amps & Circuit wiring (Copper) of 6 sq.mm, Three phase, incl suitable size of FI clamps 02 Nos with the following accessories and all as directed. Make:- For Contactor : Siemens/Lauritz Knudsen (L&T)/BCH / make given in Appx 'B'For MCBs : Schneider/Lauritz Knudsen (L&T)/Siemens / make given in Appx 'B'For Enclosure: : Hensel, GE, Walther or equivalent / make given in Appx 'B'For Circuit Wiring : Polycab/Finolex / make given in Appx 'B' Make : SWADEEP (KAKATIYA) or equivalent as approved by Accepting Officer |
| 11 | S & F in replacement of LED lamp 9 Watt B22 completed all as specified and directed. |
| 12 | M&L for earthing complete with galvanised steel earth plate electrode 600 x 600 x 6 mm thick, burried directly into the ground (earth pit not less than 2.25 mtr below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to GI earth wire 4 mm dia by means of bolts, nuts, check nuts, and washers of galvanised iron or steel all as shown in electrical plate No - 3 connected to earthing test point all as specified or indicated including excavation and connected earth work, PCC chamber and cover, watering pipe, funnel wire mesh but without earth lead protection pipe and test on completion after dismantling unserviceable erthing (above GL only) complete all as directed incl dismantling of existing earthing. ( Note :- On testing after completion if desired earth resistence is not obtained, the earthing will be redone at no extra cost.) |
| 13 | M & L in replacement for Thermoplastic cable junction boxes of size 240mm x 130mm x 110mm, IP 65/66 with metric knockouts for cable entry, weather proof for outdoor installation and including glands and with 4 terminals for terminating one incoming and outgoing UG cable of size 10/16 sqmm 3.5/4 core and fixed to the PCC/Steel Poles by means of suitable size of clamps with nut and bolts and all specified and directed. |
| 14 | All as per item 12.00 above but of size 140mmx140mmx95mm |
| 15 | Supply, Laying, testing and commissioning in replacement of LT cable XLPE Insulated screened PVC bedded, galvanized steel strip armoured service cable pole to building electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 Sqmm 4.0 Core incl dismantling old cable complete all as specified and directed. |
| 16 | All as per item 14.00 above but of size 10 Sqmm 4.0 Core |
| 17 | All as per item 14.00 above but of size 6 Sqmm 4.0 Core |
| 18 | S & F in replacement of PVC insulated and PVC sheathed three core 1.5 Sqmm multistranded copper conductor cable 1100 volts complete all as specified and directed. |
| 19 | S & F in replacement of 40 mm bore GI Tubing light grade with all fittings for cable protection laid across roads, in trenches or across PCC drain, along electric pole or floor/wall including suitable size MS Clamps, nuts and bolts and washers complete all as specified and directed. |
| 20 | All as per item 18.00 above but of size 25mm bore |
| 21 | M & L Sand cushioning & cover for protection of under ground electric cable in trenches and punning to specified thickness complete all as specified and directed.Note :- (i) Approved dry sand free from vegetation, grass & other deleterious substances shall be used.(ii) For the purpose of payment, only punned thickness shall be measured. |
| 22 | M & L for old size sub class 'B' bricks well burnt, laid flat, for cable protection complete all as specified and directed. |
| 23 | Excavation in trenches not exceeding 1.5 mtrs wide and not exceeding 1.5 mtrs in depth for laying of cables including getting out in any type of soil complete all as specified and directed. |
| 24 | Returning filling in including spreading, leveling ,and well ramming, in layers not exceeding 25 cm each layer of any type of soil complete all as specified and directed |
| 25 | Removing surplus excavated material from site not exceeding 50 mtrs from starting point and depositing where directed at level not exceeding 1.5 mtr above the starting point complete all as specified and directed |
| 26 | M&L for PCC (1:3:6) type C-1 (using 20mm graded stone aggregate) as in coping/stay of pole etc, including form work (straight or curved) & finishing the surfaces even & smooth without using extra cement complete all as specified and as directed. |
| 27 | S&F in replacement of street light bracket made of 40 mm dia light grade GI pipe, 1.5 long long, bent to shape (120º), fixed with two pairs of 50 x 5 mm MS flat iron clamps with suitable nuts and bolts for mounting security light fittings in steel tubular poles including aluminium painting on clamps, complete all as specified and directed. Please Enable Macros to View BoQ information |
