|
| 1 | Interlocking road (MORTH ITEMS) |
| 2 | OD9549/2026-2027: Granular sub-base/base/surface course with local materials (Table 400.13) by mix in place method normal. Construction of granular sub-base by providing local material spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at once and compacting with smooth wheel roller to achieve the desired density complete as per Clause 401.4 as per Technical Specification Clause 408. (ii) Using Gravel mix soil. |
| 3 | 55.23:Supplying and laying interlocking tile 80mm or nearest size thickness, minimum strength M30 including providing a layer of 6mm aggregate for 5cm thickness, then laying interlock cobbles in lines and levels as per the directions of the departmental officers at site inclusive of all cost & conveyance charges etc. complete. |
| 4 | Interlocking road (DSR ITEMS) |
| 5 | 2.31:Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared |
| 6 | 2.6.1:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.All kinds of soil |
| 7 | 4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III)derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 8 | 10.26.3:Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approves steel primer.G.I. pipes |
| 9 | 13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work |
| 10 | OD52249/2025-2026:Name board of size 75X60 cm installed in the appropriate place visible to the public made of brick wall with granite plaque should be inserted and engraving letters etc. complete as per departmental officers at site. |
| 11 | OD52315/2025-2026:Manufacturing, supplying and fixing sign boards of size 1.2 x 0.6m made up of 2 mm thick Japan sheet, support frame of M.S. angle iron of size 25x25x3 mm to 2 vertical posts 2.2m long made up of M.S. Tee section ISNT 40x40x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer .Backside of sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat and firmly fixed to the ground after excavation by means of properly designed foundation of size 0.25x0.25x0.45m with CC 1:2:4 using 20mm broken stone including all cost and conveyance of materials, labour charges, leads and lifts etc. complete as per drawing , specification and direction of Engineer--in-charge. (excluding lettering which is paid separately) |
| 12 | 13.71:Lettering with black Japan pint of approved brand and manufacture Please Enable Macros to View BoQ information |
